Create a new version of paste:

smartctl 6.2 2013-04-20 r3812 [x86_64-linux-3.11.0-12-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Scorpio Blue Serial ATA
Device Model:     WDC WD3200BEVT-22ZCT0
Serial Number:    WD-WXE308P51203
LU WWN Device Id: 5 0014ee 2ac0b78e3
Firmware Version: 11.01A11
User Capacity:    320,072,933,376 bytes [320 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS (minor revision not indicated)
SATA Version is:  SATA 2.5, 1.5 Gb/s
Local Time is:    Sun Nov 17 14:08:41 2013 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      ( 121)	The previous self-test completed having
					the read element of the test failed.
Total time to complete Offline 
data collection: 		(10800) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 127) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x303f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       963
  3 Spin_Up_Time            0x0027   193   186   021    Pre-fail  Always       -       1341
  4 Start_Stop_Count        0x0032   096   096   000    Old_age   Always       -       4915
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   100   253   051    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   070   070   000    Old_age   Always       -       22093
 10 Spin_Retry_Count        0x0033   100   098   051    Pre-fail  Always       -       0
 11 Calibration_Retry_Count 0x0032   100   100   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   096   096   000    Old_age   Always       -       4225
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       566
193 Load_Cycle_Count        0x0032   129   129   000    Old_age   Always       -       215661
194 Temperature_Celsius     0x0022   105   074   000    Old_age   Always       -       42
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   199   199   000    Old_age   Always       -       75
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0009   100   253   051    Pre-fail  Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 5124 (device log contains only the most recent five errors)
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 5124 occurred at disk power-on lifetime: 22093 hours (920 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 00 00 00 e0  Error: UNC at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 00 00 00 00 00      01:21:34.150  READ DMA
  ef 10 02 00 00 00 00 00      01:21:34.150  SET FEATURES [Enable SATA feature]
  27 00 00 00 00 00 00 00      01:21:34.149  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 00 00      01:21:34.149  IDENTIFY DEVICE
  ef 03 42 00 00 00 00 00      01:21:34.149  SET FEATURES [Set transfer mode]

Error 5123 occurred at disk power-on lifetime: 22093 hours (920 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 00 00 00 e0  Error: UNC at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 20 00 00 00 00 00      01:21:31.202  READ DMA
  ef 10 02 00 00 00 00 00      01:21:31.202  SET FEATURES [Enable SATA feature]
  27 00 00 00 00 00 00 00      01:21:31.202  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 00 00      01:21:31.201  IDENTIFY DEVICE
  ef 03 42 00 00 00 00 00      01:21:31.201  SET FEATURES [Set transfer mode]

Error 5122 occurred at disk power-on lifetime: 22093 hours (920 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  01 51 00 00 00 00 e0  Error: AMNF at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 20 00 00 00 00 00      01:21:28.107  READ DMA
  ef 10 02 00 00 00 00 00      01:21:28.107  SET FEATURES [Enable SATA feature]
  27 00 00 00 00 00 00 00      01:21:28.107  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 00 00      01:21:28.106  IDENTIFY DEVICE
  ef 03 42 00 00 00 00 00      01:21:28.106  SET FEATURES [Set transfer mode]

Error 5121 occurred at disk power-on lifetime: 22093 hours (920 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  01 51 00 00 00 00 e0  Error: AMNF at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 20 00 00 00 00 00      01:21:25.014  READ DMA
  25 00 08 a8 ea 42 25 00      01:21:25.014  READ DMA EXT
  ef 10 02 00 00 00 00 00      01:21:25.014  SET FEATURES [Enable SATA feature]
  27 00 00 00 00 00 00 00      01:21:25.013  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 00 00      01:21:25.013  IDENTIFY DEVICE

Error 5120 occurred at disk power-on lifetime: 22093 hours (920 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 00 00 00 e0  Error: UNC at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 00 00 00 00 00      01:21:21.767  READ DMA
  ef 10 02 00 00 00 00 00      01:21:21.767  SET FEATURES [Enable SATA feature]
  27 00 00 00 00 00 00 00      01:21:21.767  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 00 00      01:21:21.766  IDENTIFY DEVICE
  ef 03 42 00 00 00 00 00      01:21:21.766  SET FEATURES [Set transfer mode]

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed: read failure       90%     22093         0
# 2  Short offline       Completed: read failure       90%     22093         0
# 3  Short offline       Completed: read failure       90%     22093         0
# 4  Extended offline    Completed: read failure       90%     22093         0

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.