Create a new version of paste:

Terminal ready
U-Boot SPL 2013.01.01 (Mar 13 2013 - 17:06:24)
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img


U-Boot 2013.01.01 (Mar 13 2013 - 17:06:24)

OMAP3530-GP ES3.0, CPU-OPP2, L3-165MHz, Max CPU Clock 600 mHz
OMAP3 Beagle board + LPDDR/NAND
I2C:   ready
DRAM:  256 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Beagle Rev C1/C2/C3
timed out in wait_for_pin: I2C_STAT=0
No EEPROM on expansion board
Die ID #0a8600030000000004013f780600a00e
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 1.400 
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 480ab000 using PIO, IRQ 0
Net:   usb_ether
Hit any key to stop autoboot:  3  2  1  0 
mmc0 is current device
gpio: pin 173 (gpio 173) value is 1
gpio: pin 7 (gpio 7) value is 0
SD/MMC found on device 0
reading uEnv.txt
690 bytes read in 5 ms (134.8 KiB/s)
Loaded environment from uEnv.txt
Importing environment from mmc ...
Running uenvcmd ...
gpio: pin 173 (gpio 173) value is 1
gpio: pin 7 (gpio 7) value is 0
baudrate=115200
beaglerev=Cx
bootargs=console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait earlyprintk
bootcmd=if run userbutton; then run bootcmd_dt; else run bootcmd_nodt; fi
bootcmd_dt=printenv;echo "NOTE: DT BOOT: booting from MMC filesystem";sleep 1;run fatloaduimage; sleep 1; run loaddtb; echo "starting.."; sleep 1; run bootwdtb
bootcmd_nodt=printenv;echo "NOTE: NODT BOOT: booting from MMC filesystem";run fatloaduimage;  ; echo "starting..";  bootm ${loadaddr}
bootdelay=3
bootenv=uEnv.txt
bootfile=uImage.beagle
bootwdtb=bootm ${loadaddr} - ${fdtbaddr}
buddy=none
camera=none
console=ttyO2,115200n8
defaultdisplay=dvi
dieid#=0a8600030000000004013f780600a00e
dvimode=640x480MR-16@60
ethact=usb_ether
fatloaduimage=fatload mmc 0:1 ${loadaddr} uImage
fdtbaddr=0x80F80000
filesize=0x2b2
importbootenv=echo Importing environment from mmc ...; env import -t $loadaddr $filesize
loadaddr=0x80200000
loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}
loaddtb=fatload mmc 0:1 ${fdtbaddr} omap3-beagle.dtb; fdt addr ${fdtbaddr}; fdt resize
loadramdisk=fatload mmc ${mmcdev} ${rdaddr} ramdisk.gz
loaduimage=ext2load mmc ${mmcdev}:2 ${loadaddr} /boot/uImage
loaduimagefat=fatload mmc ${mmcdev} ${loadaddr} uImage
mmcargs=setenv bootargs console=${console} ${optargs} mpurate=${mpurate} buddy=${buddy} camera=${camera} vram=${vram} omapfb.mode=dvi:${dvimode} omapdss.def_disp=${defaultdisplay} root=${mmcroot} rootfstype=${mmcrootfstype}
mmcboot=echo Booting from mmc ...; run mmcargs; bootm ${loadaddr}
mmcdev=0
mmcroot=/dev/mmcblk0p2 rw
mmcrootfstype=ext3 rootwait
mpurate=auto
nandargs=setenv bootargs console=${console} ${optargs} mpurate=${mpurate} buddy=${buddy} camera=${camera} vram=${vram} omapfb.mode=dvi:${dvimode} omapdss.def_disp=${defaultdisplay} root=${nandroot} rootfstype=${nandrootfstype}
nandboot=echo Booting from nand ...; run nandargs; nand read ${loadaddr} 280000 400000; bootm ${loadaddr}
nandroot=ubi0:rootfs ubi.mtd=4
nandrootfstype=ubifs
ramargs=setenv bootargs console=${console} ${optargs} mpurate=${mpurate} buddy=${buddy} vram=${vram} omapfb.mode=dvi:${dvimode} omapdss.def_disp=${defaultdisplay} root=${ramroot} rootfstype=${ramrootfstype}
ramboot=echo Booting from ramdisk ...; run ramargs; bootm ${loadaddr}
ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M
ramrootfstype=ext2
rdaddr=0x81000000
stderr=serial
stdin=serial
stdout=serial
uenvcmd=boot
usbtty=cdc_acm
userbutton=if gpio input 173; then run userbutton_xm; else run userbutton_nonxm; fi;
userbutton_nonxm=gpio input 7;
userbutton_xm=gpio input 4;
vram=12M

Environment size: 2688/131068 bytes
NOTE: DT BOOT: booting from MMC filesystem
reading uImage
3850592 bytes read in 293 ms (12.5 MiB/s)
reading omap3-beagle.dtb
11872 bytes read in 8 ms (1.4 MiB/s)
starting..
## Booting kernel from Legacy Image at 80200000 ...
   Image Name:   Linux-3.9.0-11594-gb4376c4
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3850528 Bytes = 3.7 MiB
   Load Address: 80800000
   Entry Point:  80800000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 80f80000
   Booting using the fdt blob at 0x80f80000
   Loading Kernel Image ... OK
OK
   reserving fdt memory region: addr=80f80000 size=3000
   Loading Device Tree to 87ffa000, end 87ffffff ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.9.0-11594-gb4376c4 (nmenon@kahuna) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #18 SMP Wed May 8 11:40:11 CDT 2013
[    0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: Generic OMAP3-GP (Flattened Device Tree), model: TI OMAP3 BeagleBoard
[    0.000000] cma: CMA: reserved 16 MiB at 8e800000
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] OMAP3430/3530 ES3.0 (l2cache iva sgx neon isp )
[    0.000000] PERCPU: Embedded 9 pages/cpu @c0a14000 s12864 r8192 d15808 u36864
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64768
[    0.000000] Kernel command line: console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait earlyprintk
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 255MB = 255MB total
[    0.000000] Memory: 234108k/234108k available, 28036k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06be418   (6874 kB)
[    0.000000]       .init : 0xc06bf000 - 0xc0722240   ( 397 kB)
[    0.000000]       .data : 0xc0724000 - 0xc079e740   ( 490 kB)
[    0.000000]        .bss : 0xc079e740 - 0xc080a7fc   ( 433 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[    0.000000] Total of 96 interrupts on 1 active controller
[    0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
[    0.000000] OMAP clockevent source: timer12 at 32768 Hz
[    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[    0.000000] OMAP clocksource: 32k_counter at 32768 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000366] Calibrating delay loop... 317.03 BogoMIPS (lpj=1585152)
[    0.047760] pid_max: default: 32768 minimum: 301
[    0.048004] Security Framework initialized
[    0.048095] Mount-cache hash table entries: 512
[    0.053314] CPU: Testing write buffer coherency: ok
[    0.053833] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[    0.053924] Setting up static identity map for 0xc04c7650 - 0xc04c76a8
[    0.055358] Brought up 1 CPUs
[    0.055389] SMP: Total of 1 processors activated (317.03 BogoMIPS).
[    0.055419] CPU: All CPU(s) started in SVC mode.
[    0.056488] devtmpfs: initialized
[    0.120422] pinctrl core: initialized pinctrl subsystem
[    0.121765] regulator-dummy: no parameters
[    0.124298] NET: Registered protocol family 16
[    0.128662] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.139404] Reprogramming SDRC clock to 332000000 Hz
[    0.145629] OMAP GPIO hardware version 2.5
[    0.160675] platform 49022000.mcbsp: alias fck already exists
[    0.161346] platform 49024000.mcbsp: alias fck already exists
[    0.169647] omap-gpmc 6e000000.gpmc: GPMC revision 5.0
[    0.171936] No ATAGs?
[    0.171936] hw-breakpoint: debug architecture 0x4 unsupported.
[    0.175048] OMAP DMA hardware revision 4.0
[    0.175720] Serial: AMBA PL011 UART driver
[    0.214538] bio: create slab <bio-0> at 0
[    0.262298] omap-dma-engine omap-dma-engine: OMAP DMA engine driver
[    0.263427] hsusb2_reset: 3300 mV 
[    0.263671] platform hsusb2_power_reg.20: Driver reg-fixed-voltage requests probe deferral
[    0.269287] SCSI subsystem initialized
[    0.270629] usbcore: registered new interface driver usbfs
[    0.270935] usbcore: registered new interface driver hub
[    0.271362] usbcore: registered new device driver usb
[    0.273223] omap_i2c i2c.9: did not get pins for i2c error: -19
[    0.274108] omap_i2c i2c.9: bus 0 rev3.3 at 2600 kHz
[    0.280670] twl 0-0048: PIH (irq 23) chaining IRQs 338..346
[    0.280853] twl 0-0048: power (irq 343) chaining IRQs 346..353
[    0.283355] VDD1: 600 <--> 1450 mV at 1275 mV 
[    0.285003] VDAC: 1800 mV 
[    0.286621] VPLL2: 1800 mV 
[    0.288269] VMMC1: 1850 <--> 3150 mV at 3150 mV 
[    0.289550] VUSB1V5: 1500 mV 
[    0.290710] VUSB1V8: 1800 mV 
[    0.291839] VUSB3V1: 3100 mV 
[    0.293090] VSIM: 1800 <--> 3000 mV at 1800 mV 
[    0.294586] twl4030_gpio gpio.32: gpio (irq 338) chaining IRQs 354..371
[    0.297088] omap_i2c i2c.10: did not get pins for i2c error: -19
[    0.297882] omap_i2c i2c.10: bus 1 rev3.3 at 100 kHz
[    0.298034] omap_i2c i2c.11: did not get pins for i2c error: -19
[    0.298767] omap_i2c i2c.11: bus 2 rev3.3 at 100 kHz
[    0.302612] Switching to clocksource 32k_counter
[    0.363067] NET: Registered protocol family 2
[    0.364044] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.364105] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    0.364166] TCP: Hash tables configured (established 2048 bind 2048)
[    0.364318] TCP: reno registered
[    0.364318] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.364379] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.364746] NET: Registered protocol family 1
[    0.365295] RPC: Registered named UNIX socket transport module.
[    0.365295] RPC: Registered udp transport module.
[    0.365325] RPC: Registered tcp transport module.
[    0.365325] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.365783] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.365966] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[    0.569183] VFS: Disk quotas dquot_6.5.2
[    0.569458] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.570617] NFS: Registering the id_resolver key type
[    0.570709] Key type id_resolver registered
[    0.570709] Key type id_legacy registered
[    0.570770] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.571105] msgmni has been set to 489
[    0.572723] io scheduler noop registered
[    0.572723] io scheduler deadline registered
[    0.572784] io scheduler cfq registered (default)
[    0.574798] pinctrl-single 48002030.pinmux: 742 pins at pa fa002030 size 1484
[    0.575103] pinctrl-single 48002a00.pinmux: 46 pins at pa fa002a00 size 92
[    0.577636] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.581237] omap_uart serial.6: did not get pins for uart0 error: -19
[    0.581512] serial.6: ttyO0 at MMIO 0x4806a000 (irq = 88) is a OMAP UART0
[    0.582366] omap_uart serial.7: did not get pins for uart1 error: -19
[    0.582641] serial.7: ttyO1 at MMIO 0x4806c000 (irq = 89) is a OMAP UART1
[    0.583465] omap_uart serial.8: did not get pins for uart2 error: -19
[    0.583709] serial.8: ttyO2 at MMIO 0x49020000 (irq = 90) is a OMAP UART2
[    1.277740] console [ttyO2] enabled
[    1.301910] brd: module loaded
[    1.316406] loop: module loaded
[    1.322967] mtdoops: mtd device (mtddev=name/number) must be supplied
[    1.330169] OneNAND driver initializing
[    1.335235] omap2_mcspi spi.12: pins are not configured from the driver
[    1.343017] omap2_mcspi spi.13: pins are not configured from the driver
[    1.350646] omap2_mcspi spi.14: pins are not configured from the driver
[    1.358428] omap2_mcspi spi.15: pins are not configured from the driver
[    1.369903] usbcore: registered new interface driver asix
[    1.375976] usbcore: registered new interface driver ax88179_178a
[    1.382781] usbcore: registered new interface driver cdc_ether
[    1.389221] usbcore: registered new interface driver smsc95xx
[    1.395782] usbcore: registered new interface driver net1080
[    1.402008] usbcore: registered new interface driver cdc_subset
[    1.408569] usbcore: registered new interface driver zaurus
[    1.414916] usbcore: registered new interface driver cdc_ncm
[    1.421966] usbcore: registered new interface driver cdc_wdm
[    1.428314] usbcore: registered new interface driver usb-storage
[    1.434967] usbcore: registered new interface driver usbtest
[    1.441864] mousedev: PS/2 mouse device common for all mice
[    1.451202] twl_rtc rtc.22: Enabling TWL-RTC
[    1.458374] twl_rtc rtc.22: rtc core: registered rtc.22 as rtc0
[    1.465545] i2c /dev entries driver
[    1.470825] Driver for 1-wire Dallas network protocol.
[    1.479217] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[    1.490692] omap-dma-engine omap-dma-engine: allocating channel for 62
[    1.497711] omap-dma-engine omap-dma-engine: allocating channel for 61
[    1.505920] omap_hsmmc mmc.16: pins are not configured from the driver
[    1.557373] usbcore: registered new interface driver usbhid
[    1.563323] usbhid: USB HID core driver
[    1.568298] oprofile: using arm/armv7
[    1.572570] TCP: cubic registered
[    1.576110] Initializing XFRM netlink socket
[    1.580627] NET: Registered protocol family 17
[    1.585357] NET: Registered protocol family 15
[    1.590179] Key type dns_resolver registered
[    1.594818] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
[    1.604614] PM: no software I/O chain control; some wakeups may be lost
[    1.611968] ThumbEE CPU extension supported.
[    1.616607] Registering SWP/SWPB emulation handler
[    1.624603] VUSB3V1: disabling
[    1.629089] VUSB1V8: disabling
[    1.634460] VUSB1V5: disabling
[    1.638092] VPLL2: disabling
[    1.641479] VDAC: disabling
[    1.646362] hsusb2_vbus: 3300 mV 
[    1.652984] twl_rtc rtc.22: setting system clock to 2000-01-01 00:24:20 UTC (946686260)
[    1.662506] Waiting for root device /dev/mmcblk0p2...
[    1.677795] mmc0: host does not support reading read-only switch. assuming write-enable.
[    1.689117] mmc0: new high speed SDHC card at address 1234
[    1.696014] mmcblk0: mmc0:1234 SA04G 3.63 GiB 
[    1.703521]  mmcblk0: p1 p2
[    4.030029] EXT4-fs (mmcblk0p2): recovery complete
[    4.039916] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    4.048492] VFS: Mounted root (ext4 filesystem) on device 179:2.
[    4.066528] devtmpfs: mounted
[    4.070648] Freeing unused kernel memory: 396K (c06bf000 - c0722000)
Mounting proc : OK
Mounting sysfs : OK
Mounting devtmpfs:mount: mounting none on /dev failed: Device or resource busy
boot mounted: OK
/dev/ttyO2 linked to /dev/tty-bd - using as console

******************************************
Starting System Init for GenericOMAP3-GP(FlattenedDeviceTree)
Release: X.x
Kernel: Linux GenericOMAP3-GP(FlattenedDeviceTree) 3.9.0-11594-gb4376c4 #18 SMP Wed May 8 11:40:11 CDT 2013 armv7l GNU/Linux
******************************************
Saving kernel ring buffer : OK
Mounting devpts : OK
Setting up networking
Configuring lo : OK
Starting syslogd : OK
Starting klogd : OK
Mounting filesystems : OK
mount: mounting none on /proc/bus/usb/ failed: No such file or directory

Please press Enter to activate this console. 
/ # 
/ # 
/ # 
/ # test.sh
-/bin/sh: test.sh: not found
/ # ./test.sh
===================
System CPUFREQ Configuration:
===================
Scaling driver: generic_cpu0
Scaling Regulator: /sys/class/regulator/regulator.2 : VDD1
125000 250000 500000 550000 600000  are the available frequencies
===================
Boot Configuration:
===================
bogomips@ boot:
BogoMIPS	: 317.03
Boot scaling frequency =600000
Boot VDD1 Scaling voltage(uV) =1275000
===================
Single OPP transition walk through test:
===================
1: TESTING for 1 seconds at 125000
current scaling frequency(for 125000) =125000
current VDD1 Scaling voltage(uV) =975000
bogomips@ frequency 125000:
BogoMIPS	: 66.04
2: TESTING for 1 seconds at 250000
current scaling frequency(for 250000) =250000
current VDD1 Scaling voltage(uV) =1075000
bogomips@ frequency 250000:
BogoMIPS	: 132.09
3: TESTING for 1 seconds at 500000
current scaling frequency(for 500000) =500000
current VDD1 Scaling voltage(uV) =1200000
bogomips@ frequency 500000:
BogoMIPS	: 264.19
4: TESTING for 1 seconds at 550000
current scaling frequency(for 550000) =550000
current VDD1 Scaling voltage(uV) =1275000
bogomips@ frequency 550000:
BogoMIPS	: 290.61
5: TESTING for 1 seconds at 600000
current scaling frequency(for 600000) =600000
current VDD1 Scaling voltage(uV) =1350000
bogomips@ frequency 600000:
BogoMIPS	: 317.03
===================
Rapid transitions test (print every 1000 all OPP combinations):
===================
[0] 1000: 6 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:39 CST 1999
[1] 1000: 6 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:39 CST 1999
[2] 1000: 6 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:39 CST 1999
[3] 1000: 6 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:39 CST 1999
[4] 1000: 6 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:39 CST 1999
[5] 1000: 6 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:39 CST 1999
[6] 1000: 6 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:39 CST 1999
[7] 1000: 7 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:40 CST 1999
[8] 1000: 7 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:40 CST 1999
[9] 1000: 7 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:40 CST 1999
[10] 1000: 7 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:40 CST 1999
[11] 1000: 7 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:40 CST 1999
[12] 1000: 7 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:40 CST 1999
[13] 1000: 7 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:40 CST 1999
[14] 1000: 7 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:40 CST 1999
[15] 1000: 7 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:40 CST 1999
[16] 1000: 7 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:40 CST 1999
[17] 1000: 7 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:41 CST 1999
[18] 1000: 8 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:41 CST 1999
[19] 1000: 8 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:41 CST 1999
[20] 1000: 8 Seconds: Fri Dec 31 18:24:33 CST 1999 : time now = Fri Dec 31 18:24:41 CST 1999