Create a new version of paste:

[include lcd_tweaks.cfg]
[include macros.cfg]
[include temp_sensor.cfg]

[stepper_x]
step_pin: PB13
dir_pin: PB12
enable_pin: !PB14
step_distance: 0.0125
endstop_pin: ^!PC0
position_endstop: 250
position_min: 0
position_max: 250
homing_speed: 70
homing_positive_dir: true

[tmc2209 stepper_x]
uart_pin: PC11
tx_pin: PC10
uart_address: 0
microsteps: 16
run_current: 0.5
hold_current: 0.3
interpolate: True
stealthchop_threshold: 250
#stealthchop_threshold: 0


[stepper_y]
step_pin: PB3
dir_pin: !PB4
enable_pin: !PD2
step_distance: 0.0125
endstop_pin: ^!PC1
position_endstop: 220
#position_endstop: 250
position_min: 0
position_max: 220
homing_speed: 70
homing_positive_dir: true

[tmc2209 stepper_y]
uart_pin: PC11
tx_pin: PC10
uart_address: 3
microsteps: 16
run_current: 0.5
hold_current: 0.3
interpolate: True
stealthchop_threshold: 250
#stealthchop_threshold: 0

[stepper_z]
step_pin: PB0
dir_pin: PC5
enable_pin: !PB1
step_distance: .0125
endstop_pin: probe:z_virtual_endstop
position_max: 250
homing_speed: 40
position_min: -3.0

[tmc2209 stepper_z]
uart_pin: PC11
tx_pin: PC10
uart_address: 1
microsteps: 16
run_current: 0.5
hold_current: 0.3
interpolate: True
stealthchop_threshold: 250
#stealthchop_threshold: 0

#[input_shaper]
#shaper_freq_x: 47.69
#shaper_freq_y: 44.54
#shaper_type: ei

[homing_override]
axes: z
set_position_z: 0
gcode:
    G90
    G0 Z5 F500
    G28 X0 Y0
    G0 X125 Y100 F9000
    G28 Z0
    G0 Z5 F500

[bed_mesh]
speed: 150
horizontal_move_z: 5
mesh_min: 25,35.0
mesh_max: 225.0,210
probe_count: 5,5
# the following valued is calculated with: [(probe_count x probe_count)-1] / 2
relative_reference_index: 12
algorithm: bicubic
#algorithm: lagrange
fade_start: 1
fade_end: 10
fade_target: 0

[probe]
pin: ^PC2
x_offset: 0.0
y_offset: 25.0
#z_offset: 1.85
speed: 40
samples: 2

[extruder]
max_extrude_only_distance: 700.0
max_extrude_cross_section: 2
step_pin: PB10
dir_pin: PB2
enable_pin: !PB11
#Afterburner steps:
step_distance: 0.00239605344
#M4 steps:
#step_distance: 0.0008685
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PC8
pressure_advance: 0.07
pressure_advance_smooth_time: 0.040
sensor_type: ATC Semitec 104GT-2

sensor_pin: PA0
#control = pid
#pid_kp = 18.973
#pid_ki = 0.771
#pid_kd = 116.683
min_extrude_temp: 15
min_temp: 0
max_temp: 270

[tmc2209 extruder]
uart_pin: PC11
tx_pin: PC10
uart_address: 2
microsteps: 16
run_current: 0.4
hold_current: 0.4
interpolate: false

[firmware_retraction]
retract_length: 1
retract_speed: 50
unretract_speed: 50

[heater_fan my_controller_fan]
pin: PA1
max_power: 1.00
kick_start_time: 0.100
heater: heater_bed
heater_temp: 50.0
#idle_timeout: 5

[heater_bed]
heater_pin: PC9
sensor_type: ATC Semitec 104GT-2
sensor_pin: PC3
#control = pid
#pid_kp = 60.695
#pid_ki = 1.073
#pid_kd = 858.069
min_temp: 0
max_temp: 130

[verify_heater heater_bed]
max_error: 240
hysteresis: 10

[fan]
pin: PC6

# thermally controlled hotend fan
[heater_fan my_nozzle_fan]
pin: PC7
max_power: 1.0
kick_start_time: 0.100
heater: extruder
heater_temp: 50.0
fan_speed: 0.7

[mcu]
serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_35FFD3054246303323730257-if00
restart_method: command

[force_move]
enable_force_move: True

[printer]
kinematics: corexz
max_velocity: 200
max_accel: 2500
max_accel_to_decel: 2500
max_z_velocity: 50
max_z_accel: 1000
square_corner_velocity: 4.0

[static_digital_output usb_pullup_enable]
pins: !PA14

[output_pin case_light]
pin: PC14
value: 0
shutdown_value: 0

[display]
#    FYSETC mini12864 LCD Display v2.1
lcd_type: uc1701
cs_pin: PB8
a0_pin: PB15
rst_pin: PB9
encoder_pins: ^PA9,^PA10
click_pin: ^!PB5
contrast: 63
spi_software_sclk_pin: PA5
spi_software_mosi_pin: PA7
spi_software_miso_pin: PA6
display_group: __voron_display

[neopixel fysetc_mini12864]
#    To control Neopixel RGB in mini12864 display
pin: PA15
chain_count: 3
initial_RED: 0.0
initial_GREEN: 0.0
initial_BLUE: 1.0
color_order: GRB

#[moonraker]
#trusted_clients:
#    192.168.1.0/24

[virtual_sdcard]
path: ~/sdcard


[pause_resume]
[display_status]

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	  -0.018750, -0.125000, -0.150000, -0.150000, -0.006250
#*# 	  0.081250, 0.037500, 0.006250, -0.050000, 0.081250
#*# 	  0.118750, 0.056250, 0.000000, 0.006250, -0.037500
#*# 	  0.218750, 0.125000, -0.018750, 0.012500, -0.068750
#*# 	  0.243750, 0.012500, -0.037500, -0.131250, -0.112500
#*# tension = 0.2
#*# min_x = 25.0
#*# algo = bicubic
#*# y_count = 5
#*# mesh_y_pps = 2
#*# min_y = 35.0
#*# x_count = 5
#*# max_y = 210.0
#*# mesh_x_pps = 2
#*# max_x = 225.0
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 58.221
#*# pid_ki = 0.958
#*# pid_kd = 884.234
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 22.272
#*# pid_ki = 1.116
#*# pid_kd = 111.083
#*#
#*# [probe]
#*# z_offset = 2.506