Create a new version of paste:

# smartctl --all /dev/sda
smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.11
Device Model:     ST31000340AS
Serial Number:    9QJ0G2LP
Firmware Version: SD15
User Capacity:    1 000 204 886 016 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   8
ATA Standard is:  ATA-8-ACS revision 4
Local Time is:    Mon Jun  4 12:04:05 2012 MSD
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever 
                                        been run.
Total time to complete Offline 
data collection:                 ( 634) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine 
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        ( 222) minutes.
Conveyance self-test routine
recommended polling time:        (   2) minutes.
SCT capabilities:              (0x103b) SCT Status supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   091   090   006    Pre-fail  Always       -       24097928
  3 Spin_Up_Time            0x0003   091   089   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       209
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       706
  7 Seek_Error_Rate         0x000f   066   057   030    Pre-fail  Always       -       266578322119
  9 Power_On_Hours          0x0032   074   074   000    Old_age   Always       -       23146
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       1
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       205
184 Unknown_Attribute       0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   001   001   000    Old_age   Always       -       308
188 Unknown_Attribute       0x0032   100   099   000    Old_age   Always       -       4295032834
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   071   060   045    Old_age   Always       -       29 (Lifetime Min/Max 17/37)
194 Temperature_Celsius     0x0022   029   040   000    Old_age   Always       -       29 (0 14 0 0)
195 Hardware_ECC_Recovered  0x001a   013   012   000    Old_age   Always       -       24097928
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       27
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       27
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 308 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 308 occurred at disk power-on lifetime: 23143 hours (964 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 ff ff ff ef 00  33d+06:01:22.093  READ DMA EXT
  27 00 00 00 00 00 e0 00  33d+06:01:21.993  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 a0 00  33d+06:01:21.966  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00  33d+06:01:21.948  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00  33d+06:01:21.930  READ NATIVE MAX ADDRESS EXT

Error 307 occurred at disk power-on lifetime: 23143 hours (964 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 ff ff ff ef 00  33d+06:01:18.977  READ DMA EXT
  27 00 00 00 00 00 e0 00  33d+06:01:18.909  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 a0 00  33d+06:01:18.886  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00  33d+06:01:18.875  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00  33d+06:01:18.856  READ NATIVE MAX ADDRESS EXT

Error 306 occurred at disk power-on lifetime: 23143 hours (964 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 ff ff ff ef 00  33d+06:01:15.913  READ DMA EXT
  27 00 00 00 00 00 e0 00  33d+06:01:15.846  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 a0 00  33d+06:01:15.826  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00  33d+06:01:15.806  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00  33d+06:01:15.783  READ NATIVE MAX ADDRESS EXT

Error 305 occurred at disk power-on lifetime: 23143 hours (964 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 ff ff ff ef 00  33d+06:01:12.820  READ DMA EXT
  27 00 00 00 00 00 e0 00  33d+06:01:12.740  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 a0 00  33d+06:01:12.716  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00  33d+06:01:12.703  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00  33d+06:01:12.682  READ NATIVE MAX ADDRESS EXT

Error 304 occurred at disk power-on lifetime: 23143 hours (964 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 ff ff ff ef 00  33d+06:01:09.694  READ DMA EXT
  27 00 00 00 00 00 e0 00  33d+06:01:09.618  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 a0 00  33d+06:01:09.605  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00  33d+06:01:09.546  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00  33d+06:01:09.327  READ NATIVE MAX ADDRESS EXT

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.