Create a new version of paste:

Linux version 2.6.36 (root@wiair-desktop) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r9319) ) #314 Wed Apr 12 11:49:31 CST 2017

 The CPU feqenuce set to 580 MHz
 PCIE: bypass PCIe DLL.
 PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
 disable all power about PCIe
CPU revision is: 00019650 (MIPS 24Kc)
Software DMA cache coherency
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
User-defined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
On node 0 totalpages: 16384
free_area_init_node: node 0, pgdat 803f7c80, node_mem_map 81000000
  Normal zone: 128 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 16256 pages, LIFO batch:3
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: mem=64M console=ttyS1,57600n8 root=/dev/mtdblock6 rootfstype=squashfs  console=ttyS0 init_debug=99
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0007326f
Readback ErrCtl register=0007326f
Memory: 60424k/65536k available (3376k kernel code, 5112k reserved, 691k data, 160k init, 0k highmem)
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 4096 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 1a311d
RALINK_GPIOMODE = 18311d
PPLL_CFG1=0xe6c000
MT7620 PPLL lock
PPLL_DRV =0x80080504
start PCIe register access
RALINK_RSTCTRL = 2400000
RALINK_CLKCFG1 = 75afffc0

*************** MT7620 PCIe RC mode *************
PCIE0 enabled
init_rt2880pci done
bio: create slab <bio-0> at 0
SCSI subsystem initialized
pci 0000:00:00.0: reg 10: [mem 0x00000000-0x7fffffff]
pci 0000:00:00.0: reg 14: [mem 0x00000000-0x0000ffff]
pci 0000:00:00.0: supports D1
pci 0000:00:00.0: PME# supported from D0 D1 D3hot
pci 0000:00:00.0: PME# disabled
pci 0000:01:00.0: reg 10: [mem 0x00000000-0x000fffff 64bit]
pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff 64bit] (PCI address [0x20000000-0x200fffff]
pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [io  disabled]
pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]
PCI: Setting latency timer of device 0000:00:00.0 to 64
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 20200000
res[1]->end = 2020ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20000000
res[0]->end = 200fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
PCI: CLS 80 bytes, default 32
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (ZLIB) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 118
io scheduler noop registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
brd: module loaded
deice id : c2 20 17 c2 20 (2017c220)
MX25L6405D(c2 2017c220) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
Creating 6 MTD partitions on "raspi":
0x000000000000-0x000000800000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "params"
0x000000060000-0x000000800000 : "firmware"
mtd: try split firmware partition
mtd: split_firmware
mtd: firmware_partition->size   0x7a0000
mtd: firmware_partition->offset 0x600.e84e
SMACCR0 -- : 0x064bc9a2
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
u32 classifier
nf_conntrack version 0.5.0 (944 buckets, 3776 max)
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
 ---EDUP LED GPIO INIT--- 
----------------------------
--------igd inited----------
----------------------------
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
Freeing unused kernel memory: 160k freed
JFFS2 notice: (70) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (1 unchecked, 1 orphan) and 12 of xref (0 dead, 6 orphan) found.
JFFS2 notice: (67) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (1 unchecked, 1 orphan) and 12 of xref (0 dead, 6 orphan) found.
register rt2860
PCI: Setting latency timer of device 0000:01:00.0 to 64


=== pAd = c0602000, size = 2163888 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc0500000, csr_addr=0xc0500000!
device_id =0x7662
==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
E2pAccessMode=2
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Not Equal!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(1)
Key1Str is Invalid key length(0) or Type(1)
Key2Str is Invalid key length(0) or Type(1)
Key2Str is Invalid key length(0) or Type(1)
Key3Str is Invalid key length(0) or Type(1)
Key3Str is Invalid key length(0) or Type(1)
Key4Str is Invalid key length(0) or Type(1)
Key4Str is Invalid key length(0) or Type(1)
WiFi Mcast disabled=0
RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
NVM is FLASH mode (pAd->flash_offset = 0x48000)
get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
fill: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
l7 inited
PPTP driver version 0.8.5
Raeth v3.1 (NAPI
)

phy_tx_ring = 0x02810000, tx_ring = 0xa2810000

phy_rx_ring0 = 0x02812000, rx_ring0 = 0xa2812000
SMACCR1 -- : 0x0000e84e
SMACCR0 -- : 0x064bc9a2
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20710000
device eth0.1 entered promiscuous mode
device eth0 entered promiscuous mode
-------->fdb_create, 402!!!
br-lan: port 1(eth0.1) entering learning state
br-lan: port 1(eth0.1) entering learning state
0x1300 = 00064320
device ra0 entered promiscuous mode
br-lan: port 2(ra0) entering learning state
br-lan: port 2(ra0) entering learning state
device ra1 entered promiscuous mode
-------->fdb_create, 402!!!
build time = 
20141115060606a
rom patch for E3 IC

platform = 
ALPS
hw/sw version = 
ä.ä.
patch version = 
.
FW Version:0.0.00 Build:1
Build Time:201507311614____
fw for E3 IC
RX[0] DESC a35ec000 size = 4096
RX[1] DESC a35ed000 size = 4096
E2pAccessMode=2
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Not Equal!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(1)
Key1Str is Invalid key length(0) or Type(1)
Key2Str is Invalid key length(0) or Type(1)
Key2Str is Invalid key length(0) or Type(1)
Key3Str is Invalid key length(0) or Type(1)
Key3Str is Invalid key length(0) or Type(1)
Key4Str is Invalid key length(0) or Type(1)
Key4Str is Invalid key length(0) or Type(1)
WiFi Mcast disabled=0
1. Phy Mode = 49
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (171)
get_chl_grp:illegal channel (171)
/home/wiair/cs/n/project/7620_1263/kernel//mt76x2e-p4rev-170120/build/../src/chips/mt76x2.c:3034 assert (ad->TxPower[choffset].Channel == 42)failed
Country Region from e2p = ffff
mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0
mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=1
mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=15, low_temp_slope=9
mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0
mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4
mt76x2_read_tx_alc_info_.= rt28xx_init, Status=0
get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=apclii
RTMPDrvOpen(1):Check if PDMA is idle!
RTMPDrvOpen(2):Check if PDMA is idle!
device rai0 entered promiscuous mode
-------->fdb_create, 402!!!
br-lan: port 4(rai0) entering learning state
br-lan: port 4(rai0) entering learning state
device rai1 entered promiscuous mode
-------->fdb_create, 402!!!
br-lan: port 1(eth0.1) entering forwarding state
br-lan: port 2(ra0) entering forwarding state
br-lan: port 4(rai0) entering forwarding state