=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.09.28 18:43:19 =~=~=~=~=~=~=~=~=~=~=~=
†!UÒššŠÂ’j
BT : 11:35:50 Sep  7 2015
PMU:rn5t618
DC01 v:1100, 0x[36]: 18 -> 28
DC02 v:1150, 0x[37]: 18 -> 2c
DC03 v:1500, 0x[38]: 38 -> 48
LDO01 v:2900, 0x[4c]: 4e -> 50
LDO02 v:1800, 0x[4d]: 24 -> 24
LDO03 v:1800, 0x[4e]: 30 -> 30
LDO04 v:2850, 0x[4f]: 4e -> 4e
LDO05 v:1800, 0x[50]: 24 -> 24
LDO0a v:2700, 0x[56]: 28 -> 28
LDO0b v:900, 0x[57]: 00 -> 00

CPU clock is 1200MHz

CPU type: M8
DDR info: 2GB(auto) @ 792MHz(1T)
DDR channel: DDR 0 + DDR 1

DDR init use : 11897 us

HHH
Boot From SPI
ucl decompress...pass
0x12345678
Boot from internal device 1st SPI

TE : 403797

System Started


U-boot(m8_k200_v1@t8) (Sep 07 2015 - 11:35:45)

clr h-ram
DRAM:  2 GiB
relocation Offset is: 6feb0000
show partition table:
part: 0, name :       logo, size : 2000000
part: 1, name :   recovery, size : 2000000
part: 2, name :       misc, size : 2000000
part: 3, name :       boot, size : 2000000
part: 4, name :     system, size : 40000000
part: 5, name :      cache, size : 20000000
part: 6, name :       data, size : end
aml_card_type=0x100
MMC:   [mmc_register] add mmc dev_num=0, port=1, if_type=6
[mmc_register] add mmc dev_num=1, port=2, if_type=6
SDIO Port B: 0, SDIO Port C: 1
PMU fault status:
reg[0x9A] = 0x1d
LSI version:03, OTP version:06
PMU type:RN5T618
register usb cfg[0][1] = 7ff68014
register usb cfg[2][0] = 7ff6b93c
NAND:  SPI BOOT: boot_device_flag 0
Nand PHY driver Version: 2.01.001.0004 (c) 2013 Amlogic Inc.
amlnf_phy_init : amlnf init flag 0
NAND device id: 2c 64 44 4b a9 0 0 0
detect NAND device: B revision NAND 8GiB MT29F64G08CBABA
nand chip ce mask 1
AML_NAND_NEW_OOB : new oob
bus_cycle=6, bus_timing=8,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
NAND CKECK  : arg nbbt: arg_valid= 1, valid_blk_addr = 7, valid_page_addr = 0
nand block at blk 4 is bad
nand block at blk 5 is bad
NAND CKECK  : arg ncnf: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 0
nand block at blk 4 is bad
nand block at blk 5 is bad
NAND CKECK  : arg nkey: arg_valid= 1, valid_blk_addr = 6, valid_page_addr = 5
i=0,register --- nand_key
driver_version in nand  1.01.001.0004
nand partition table changed:  misc partition->size: from 1000000	to 2000000
nand dev nfcode : nr_partitions num changed from 5 to 2
nand configs confirm failed
nand configs confirm failed
shipped_bbt_valid_ops and ret:-19
get device configs failed and ret:ffffffed
nandphy_init failed and ret=0xffffffed
get_boot_device_flag: init_ret 1
get_boot_device_flag   SPI BOOT:
nand init success, change the device_boot_flag to 4 : spi+nand
SPI BOOT,spi_env_relocate_spec : env_relocate_spec 53
SF: Detected MX25L1605D with page size 256, total 2 MiB

SPI NOR Flash have write protect!!!
set_storage_device_flag: store 4
nand get nftl dev boot  failed
nftl_dev be NULL
nand cmd read failed

nand cmd store failed
Err imgread(L123):Fail to read 0x1000B from part[boot] at offset 0
check dts: FDT_ERR_BADMAGIC, load default vpu parameters
vpu driver detect cpu type: m8
vpu clk_level = 7
set vpu clk: 364300000Hz, readback: 364300000Hz(0x700)
Net:   Meson_Ethernet
init suspend firmware done. (ret:0)
cvbs trimming.1.v5: 0xa0, 0x0
charging
wipe_data=successful
wipe_cache=successful
has.accelerometer = false
cvbsmode = 576cvbs
hdmimode = 1080p
outputmode = 1080p
Using default environment

set_storage_device_flag: store 0
set_storage_device_flag: set  store to 4
SPI BOOT,spi_saveenv : saveenv 97
Erasing SPI flash...Writing to SPI flash...done
Saving Environment to SPI Flash...
SPI BOOT,spi_saveenv : saveenv 97
Erasing SPI flash...Writing to SPI flash...done
reboot_mode=charging
TV mode 1080p selected.
mode = 8  vic = 16
set HDMI vic: 16
config HPLL
config HPLL done
reconfig packet setting done
nand get nftl dev logo  failed
nftl_dev be NULL
nand cmd read failed

nand cmd store failed
Err imgread(L519):Fail to read 0x2000B from part[logo] at offset 0
There is no valid bmp file at the given address
bmp scale:  mode=1080p , x=0, y=0, w=1920, h=1080
Hit Enter key to stop autoboot -- :  1  0
exit abortboot: 0
current storer:nand_key
key save is auto select storer(nand or emmc)
write key code version3_flush:708,prov->write:7fed9a10
nand detect bad blk at 4 chip 0
nand detect bad blk at 4 chip 0
buf should never be NULL
nand write failed
buf should never be NULL
nand write failed
rewrite!
nand detect bad blk at 4 chip 0
buf should never be NULL
nand write failed
buf should never be NULL
nand write failed
rewrite!
nand detect bad blk at 4 chip 0
nand detect bad blk at 5 chip 0
nand detect bad blk at 4 chip 0
buf should never be NULL
nand write failed
buf should never be NULL
nand write failed
rewrite!
nand detect bad blk at 4 chip 0
nand detect bad blk at 5 chip 0
nand detect bad blk at 5 chip 0
buf should never be NULL
nand write failed
test block 3 times, operating environment maybe wrong!
 NAND SAVE :  arg  nkey faild at blk:5
save key error,nand_key_write
write key ok!!
Booting...
 error: image data is not a fdt
key_unify_init:364,unify key config table parse fail
Err key(L47):fail in key_drv_init
nand get nftl dev boot  failed
nftl_dev be NULL
nand cmd read failed

nand cmd store failed
Err imgread(L323):Fail to read 0x100000B from part[boot] at offset 0
Wrong Image Format for bootm command
ERROR: can't get kernel image!
enter recovery
 sdio_detect return 1
sdio debug board detected, no sd card in
(Re)start USB(0)...
USB0:   dwc_usb driver version: 2.94 6-June-2012
USB (1) peri reg base: c1108820
USB (1) use clock source: XTAL input
USB (1) base addr: 0xc90c0000
Force id mode: Host
dwc_otg: Highspeed device found !

scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

** Invalid boot device **
nand get nftl dev recovery  failed
nftl_dev be NULL
nand cmd read failed

nand cmd store failed
Err imgread(L323):Fail to read 0x100000B from part[recovery] at offset 0
no recovery in flash
m8_k200_v1#