API tools faq
paste
benoitm974

H96MAX X3 original boot log

benoitm974
Jan 9th, 2021
83
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 116.20 KB | None | 0 0
raw download clone embed print report
  1. ---------- 2021-01-08 21:48:55 +0100: Logging Started ----------
  2.  
  3. SM1:BL:511f6b:81ca2f;FEAT:A0F83180:20282000;POC:F;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
  4. bl2_stage_init 0x01
  5. bl2_stage_init 0x81
  6. hw id: 0x0001 - pwm id 0x00
  7. bl2_stage_init 0xc0
  8. bl2_stage_init 0x02
  9.  
  10. L0:00000000
  11. L1:00000703
  12. L2:00008067
  13. L3:15000020
  14. S1:00000000
  15. B2:20282000
  16. B1:a0f83180
  17.  
  18. TE: 153062
  19.  
  20. BL2 Built : 20:29:41, Jun 18 2019. g12a ga659aac - luan.yuan@droid15-sz
  21.  
  22. Board ID = 1
  23. Set cpu clk to 24M
  24. Set clk81 to 24M
  25. Use GP1_pll as DSU clk.
  26. DSU clk: 1200 Mhz
  27. CPU clk: 1200 MHz
  28. Set clk81 to 166.6M
  29. eMMC boot @ 0
  30. sw8 s
  31. DDR driver_vesion: LPDDR4_PHY_V_0_1_15 build time: Jun 18 2019 20:29:37
  32. board id: 1
  33. Load FIP HDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
  34. fw parse done
  35. Load ddrfw from eMMC, src: 0x00060200, des: 0xfffd0000, size: 0x0000c000, part: 0
  36. Load ddrfw from eMMC, src: 0x00038200, des: 0xfffd0000, size: 0x00004000, part: 0
  37. PIEI prepare done
  38. fastboot data load
  39. 00000000
  40. emmc switch 1 ok
  41. ddr saved addr:00016000
  42. Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
  43. 00000000
  44. emmc switch 0 ok
  45. fastboot data verify
  46. verify result: 0
  47. enable_fast_boot
  48. dmc_margin_rx==12 dmc_margin_tx==12 steps
  49. DDR3 probe
  50. ddr clk to 672MHz
  51. Load ddrfw from eMMC, src: 0x0002c200, des: 0xfffd0000, size: 0x0000c000, part: 0
  52.  
  53. dmc_version 0001
  54. Check phy result
  55. INFO : End of initialization
  56. INFO : Training has run successfully!
  57. aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_15 build time: Jun 18 2019 20:29:43
  58. DDR cs0 size: 3928MB
  59. DDR cs1 size: 0MB
  60. DMC_DDR_CTRL: 0000002dDDR size: 3928MB
  61. cs0 DataBus test pass
  62. cs0 AddrBus test pass
  63.  
  64. non-sec scramble use zero key
  65. ddr scramble enabled
  66.  
  67. 100bdlr_step_size ps== 418
  68. result report
  69. boot times 0Enable ddr reg access
  70. 00000000
  71. emmc switch 3 ok
  72. Authentication key not yet programmed
  73. get rpmb counter error 0x00000007
  74. 00000000
  75. emmc switch 0 ok
  76. Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
  77. Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000d0000, part: 0
  78. bl2z: ptr: 05129330, size: 00001e40
  79. 0.0;M3 CHK:0;cm4_sp_mode 0
  80. MVN_1=0x00000000
  81. MVN_2=0x00000000
  82. [Image: g12a_v1.1.3389-92241b5 2019-07-02 17:22:49 luan.yuan@droid15-sz]
  83. OPS=0x10
  84. ring efuse init
  85. 2b 0c 10 00 01 17 0c 00 00 0c 31 39 57 4b 52 50
  86. [0.017310 Inits done]
  87. secure task start!
  88. high task start!
  89. low task start!
  90. run into bl31
  91. NOTICE: BL31: v1.3(release):4fc40b1
  92. NOTICE: BL31: Built : 15:57:33, May 22 2019
  93. NOTICE: BL31: G12A normal boot!
  94. NOTICE: BL31: BL33 decompress pass
  95. ERROR: Error initializing runtime service opteed_fast
  96.  
  97.  
  98. U-Boot 2015.01 (Jan 13 2020 - 11:33:31)
  99.  
  100. DRAM: 3.8 GiB
  101. Relocation Offset is: d6e50000
  102. spi_post_bind(spifc): req_seq = 0
  103. register usb cfg[0][1] = 00000000d7f3e500
  104. NAND: get_sys_clk_rate_mtd() 290, clock setting 200!
  105. NAND device id: 0 ff ff ff ff ff
  106. No NAND device found!!!
  107. nand init failed: -6
  108. get_sys_clk_rate_mtd() 290, clock setting 200!
  109. NAND device id: 0 ff ff ff ff ff
  110. No NAND device found!!!
  111. nand init failed: -6
  112. MMC: aml_priv->desc_buf = 0x00000000d3e40a70
  113. aml_priv->desc_buf = 0x00000000d3e42db0
  114. SDIO Port B: 0, SDIO Port C: 1
  115. co-phase 0x2, tx-dly 0, clock 400000
  116. co-phase 0x2, tx-dly 0, clock 400000
  117. co-phase 0x2, tx-dly 0, clock 400000
  118. emmc/sd response timeout, cmd8, status=0x1ff2800
  119. emmc/sd response timeout, cmd55, status=0x1ff2800
  120. co-phase 0x2, tx-dly 0, clock 400000
  121. co-phase 0x2, tx-dly 0, clock 40000000
  122. aml_sd_retry_refix[983]:delay = 0x0,gadjust =0x162000
  123. [mmc_startup] mmc refix success
  124. init_part() 297: PART_TYPE_AML
  125. [mmc_init] mmc init success
  126. Amlogic multi-dtb tool
  127. Single dtb detected
  128. start dts,buffer=00000000d3e45620,dt_addr=00000000d3e45620
  129. get_partition_from_dts() 91: ret 0
  130. Amlogic multi-dtb tool
  131. Single dtb detected
  132. parts: 17
  133. 00: logo 0000000000800000 1
  134. 01: recovery 0000000001800000 1
  135. 02: misc 0000000000800000 1
  136. 03: dtbo 0000000000800000 1
  137. 04: cri_data 0000000000800000 2
  138. 05: param 0000000001000000 2
  139. 06: boot 0000000001000000 1
  140. set has_boot_slot = 0
  141. 07: rsv 0000000001000000 1
  142. 08: metadata 0000000001000000 1
  143. 09: vbmeta 0000000000200000 1
  144. 10: tee 0000000002000000 1
  145. 11: vendor 0000000014000000 1
  146. 12: odm 0000000008000000 1
  147. 13: system 0000000074000000 1
  148. 14: product 0000000008000000 1
  149. 15: cache 0000000046000000 2
  150. 16: data ffffffffffffffff 4
  151. init_part() 297: PART_TYPE_AML
  152. eMMC/TSD partition table have been checked OK!
  153. crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
  154. crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
  155. crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
  156. mmc env offset: 0x4d400000
  157. In: serial
  158. Out: serial
  159. Err: serial
  160. reboot_mode=cold_boot
  161. [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
  162. _verify_dtb_checksum()-3406: calc 6c63d38f, store 6c63d38f
  163. _verify_dtb_checksum()-3406: calc 6c63d38f, store 6c63d38f
  164. dtb_read()-3623: total valid 2
  165. update_old_dtb()-3604: do nothing
  166. Amlogic multi-dtb tool
  167. Single dtb detected
  168. amlkey_init() enter!
  169. [EFUSE_MSG]keynum is 4
  170. vpu: clk_level in dts: 7
  171. vpu: vpu_power_on
  172. vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
  173. vpu: vpu_module_init_config
  174. vpp: vpp_init
  175. vpp: vpp osd2 matrix rgb2yuv..............
  176. cvbs: cpuid:0x2b
  177. Net: dwmac.ff3f0000amlkey_init() enter!
  178. amlkey_init() 71: already init!
  179. [EFUSE_MSG]keynum is 4
  180.  
  181. CONFIG_AVB2: null
  182. Start read misc partition datas!
  183. info->magic =
  184. info->version_major = 1
  185. info->version_minor = 0
  186. info->slots[0].priority = 15
  187. info->slots[0].tries_remaining = 7
  188. info->slots[0].successful_boot = 0
  189. info->slots[1].priority = 14
  190. info->slots[1].tries_remaining = 7
  191. info->slots[1].successful_boot = 0
  192. info->crc32 = -1075449479
  193. active slot = 0
  194. wipe_data=successful
  195. wipe_cache=successful
  196. upgrade_step=2
  197. reboot_mode:::: cold_boot
  198. amlkey_init() enter!
  199. amlkey_init() 71: already init!
  200. [EFUSE_MSG]keynum is 4
  201. [KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
  202. [KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
  203. hpd_state=0
  204. edid preferred_mode is <NULL>[0]
  205. hdr mode is 0
  206. dv mode is ver:0 len: 0
  207. hdr10+ mode is 0
  208. [OSD]load fb addr from dts:/meson-fb
  209. [OSD]load fb addr from dts:/fb
  210. [OSD]set initrd_high: 0x7f800000
  211. [OSD]fb_addr for logo: 0x7f800000
  212. [OSD]load fb addr from dts:/meson-fb
  213. [OSD]load fb addr from dts:/fb
  214. [OSD]fb_addr for logo: 0x7f800000
  215. [OSD]VPP_OFIFO_SIZE:0xfff01fff
  216. [CANVAS]canvas init
  217. [CANVAS]addr=0x7f800000 width=3840, height=2160
  218. [OSD]osd_hw.free_dst_data: 0,719,0,575
  219. [OSD]osd1_update_disp_freescale_enable
  220. vpp: vpp_matrix_update: 2
  221. cvbs performance type = 9, table = 0
  222. cvbs_config_hdmipll_g12a
  223. cvbs_set_vid2_clk
  224. amlkey_init() enter!
  225. amlkey_init() 71: already init!
  226. [EFUSE_MSG]keynum is 4
  227. [KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
  228. [KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
  229. InUsbBurn
  230. noSof
  231. sof timeout, reset usb phy tuning
  232. gpio: pin GPIOAO_3 (gpio 3) value is 1
  233. Command: bcb uboot-command
  234. Start read misc partition datas!
  235. BCB hasn't any datas,exit!
  236. amlkey_init() enter!
  237. amlkey_init() 71: already init!
  238. [EFUSE_MSG]keynum is 4
  239. [KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
  240. [KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
  241. Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
  242.  
  243. ddr_set_t_p==0xd7f845e0
  244.  
  245. uboot enable auto fast boot funciton
  246.  
  247. uboot auto fast boot auto window test is done
  248. pll tsensor avg: 0x1f98, u_efuse: 0x80ca
  249. temp1: 32
  250. ddr tsensor avg: 0x1fa2, u_efuse: 0x80a7
  251. temp2: 33
  252. device cool done
  253. CONFIG_SYSTEM_AS_ROOT: systemroot
  254. system_mode: 1
  255. Start read misc partition datas!
  256. info->magic =
  257. info->version_major = 1
  258. info->version_minor = 0
  259. info->slots[0].priority = 15
  260. info->slots[0].tries_remaining = 7
  261. info->slots[0].successful_boot = 0
  262. info->slots[1].priority = 14
  263. info->slots[1].tries_remaining = 7
  264. info->slots[1].successful_boot = 0
  265. info->crc32 = -1075449479
  266. active slot = 0
  267. CONFIG_AVB2: null
  268. active_slot: normal
  269. avb2: 0
  270. ee_gate_off ...
  271. avb2: 0
  272. ## Booting Android Image at 0x01080000 ...
  273. Kernel command line: androidboot.dtbo_idx=0 --cmdline root=/dev/mmcblk0p18 buildvariant=user
  274. Start read misc partition datas!
  275. info->magic =
  276. info->version_major = 1
  277. info->version_minor = 0
  278. info->slots[0].priority = 15
  279. info->slots[0].tries_remaining = 7
  280. info->slots[0].successful_boot = 0
  281. info->slots[1].priority = 14
  282. info->slots[1].tries_remaining = 7
  283. info->slots[1].successful_boot = 0
  284. info->crc32 = -1075449479
  285. active slot = 0
  286. active_slot is normal
  287. load dtb from 0x1000000 ......
  288. Amlogic multi-dtb tool
  289. Single dtb detected
  290. find 1 dtbos
  291. dtbos to be applied: 0
  292. Apply dtbo 0
  293. Loading Kernel Image(COMP_NONE) ... OK
  294. kernel loaded at 0x01080000, end = 0x0198eea0
  295. Loading Device Tree to 0000000009fe9000, end 0000000009fff533 ... OK
  296.  
  297. Starting kernel ...
  298.  
  299. uboot time: 3501586 us
  300. [ 0.000000@0] Booting Linux on physical CPU 0x0
  301. [ 0.000000@0] Linux version 4.9.113 (user@epyc) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Mon Jan 13 11:39:18 CST 2020
  302. [ 0.000000@0] CPU: ARMv7 Processor [411fd050] revision 0 (ARMv7), cr=10c5383d
  303. [ 0.000000@0] CPU: div instructions available: patching division code
  304. [ 0.000000@0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  305. [ 0.000000@0] OF: fdt:Machine model: Amlogic
  306. [ 0.000000@0] Reserved memory: created CMA memory pool at 0x05000000, size 4 MiB
  307. [ 0.000000@0] OF: reserved mem: initialized node linux,secmon, compatible id shared-dma-pool
  308. [ 0.000000@0] Reserved memory: created CMA memory pool at 0x7f800000, size 8 MiB
  309. [ 0.000000@0] OF: reserved mem: initialized node linux,meson-fb, compatible id shared-dma-pool
  310. [ 0.000000@0] Reserved memory: created CMA memory pool at 0x77800000, size 128 MiB
  311. [ 0.000000@0] OF: reserved mem: initialized node linux,ion-dev, compatible id shared-dma-pool
  312. [ 0.000000@0] Reserved memory: created CMA memory pool at 0xd5800000, size 40 MiB
  313. [ 0.000000@0] OF: reserved mem: initialized node linux,di_cma, compatible id shared-dma-pool
  314. [ 0.000000@0] Reserved memory: regions without no-map are not yet supported
  315. [ 0.000000@0] Reserved memory: created CMA memory pool at 0x64400000, size 308 MiB
  316. [ 0.000000@0] OF: reserved mem: initialized node linux,codec_mm_cma, compatible id shared-dma-pool
  317. [ 0.000000@0] OF: reserved mem: initialized node linux,codec_mm_reserved, compatible id amlogic, codec-mm-reserved
  318. [ 0.000000@0] Reserved memory: created CMA memory pool at 0xd1800000, size 64 MiB
  319. [ 0.000000@0] OF: reserved mem: initialized node linux,vdin1_cma, compatible id shared-dma-pool
  320. [ 0.000000@0] Reserved memory: created CMA memory pool at 0xcf800000, size 32 MiB
  321. [ 0.000000@0] OF: reserved mem: initialized node linux,vm0_cma, compatible id shared-dma-pool
  322. [ 0.000000@0] cma: Reserved 8 MiB at 0xcf000000
  323. [ 0.000000@0] Memory policy: Data cache writealloc
  324. [ 0.000000@0] psci: probing for conduit method from DT.
  325. [ 0.000000@0] psci: PSCIv1.0 detected in firmware.
  326. [ 0.000000@0] psci: Using standard PSCI v0.2 function IDs
  327. [ 0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
  328. [ 0.000000@0] psci: SMC Calling Convention v1.1
  329. [ 0.000000@0] percpu: Embedded 15 pages/cpu @ee482000 s32140 r8192 d21108 u61440
  330. [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 883200
  331. [ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 otg_device=0 reboot_mode_android=normal logo=osd0,loaded,0x3d800000 vout=576cvbs,enable panel_type=lcd_1 hdmitx=,rgb,8bit hdmimode=1080p60hz frac_rate_policy=1 hdmi_read_edid=1 cvbsmode=576cvbs osd_reverse=0 video_reverse=0 irq_check_en=0 androidboot.selinux=permissive androidboot.firstboot=0 jtag=disable androidboot.hardware=amlogic androidboot.serialno=1234567890 mac=00:df:12:00:a3:31 androidboot.mac=00:df:12:00:a3:31 ro rootwait skip_initramfs androidboot.dtbo_idx=0 --cmdline root=/dev/mmcblk0p18 buildvariant=user
  332. [ 0.000000@0] fb: osd0
  333. [ 0.000000@0] fb: loaded
  334. [ 0.000000@0] fb: 0x3d800000
  335. [ 0.000000@0] vout: 576cvbs
  336. [ 0.000000@0] vout: enable: 1
  337. [ 0.000000@0] lcd: panel_type: lcd_1
  338. [ 0.000000@0] vout: get hdmimode: 1080p60hz
  339. [ 0.000000@0] hdmitx: hdmitx boot frac_rate_policy: 1
  340. [ 0.000000@0] vout: get cvbsmode: 576cvbs
  341. [ 0.000000@0] vpp_axis_reverse: bootargs is 0
  342. [ 0.000000@0] phlock_phase_config: bootargs is 0.
  343. [ 0.000000@0] jtag: jtag select disable
  344. [ 0.000000@0] PID hash table entries: 4096 (order: 2, 16384 bytes)
  345. [ 0.000000@0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  346. [ 0.000000@0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  347. [ 0.000000@0] Memory: 2879612K/3538944K available (13312K kernel code, 1248K rwdata, 4820K rodata, 1024K init, 1338K bss, 53124K reserved, 606208K cma-reserved, 2150400K highmem)
  348. [ 0.000000@0] Virtual kernel memory layout:
  349. [ 0.000000@0] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  350. [ 0.000000@0] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
  351. [ 0.000000@0] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
  352. [ 0.000000@0] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
  353. [ 0.000000@0] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  354. [ 0.000000@0] modules : 0xbc000000 - 0xbfe00000 ( 62 MB)
  355. [ 0.000000@0] .text : 0xc0108000 - 0xc0f00000 (14304 kB)
  356. [ 0.000000@0] .init : 0xc1500000 - 0xc1600000 (1024 kB)
  357. [ 0.000000@0] .data : 0xc1600000 - 0xc1738278 (1249 kB)
  358. [ 0.000000@0] .bss : 0xc173a000 - 0xc1888bc4 (1339 kB)
  359. [ 0.000000@0] zone:Normal, spaned pages:196608, total:196608
  360. [ 0.000000@0] zone:HighMem, spaned pages:688128, total:884736
  361. [ 0.000000@0] page_trace_pre_work, trace buffer:edc00000, size:360000, used:edf60000, end:ee000000
  362. [ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  363. [ 0.000000@0] Preemptible hierarchical RCU implementation.
  364. [ 0.000000@0] Build-time adjustment of leaf fanout to 32.
  365. [ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
  366. [ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=4
  367. [ 0.000000@0] NR_IRQS:16 nr_irqs:16 16
  368. [ 0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
  369. [ 0.000000@0] g12a_aoclkc_init: register ao clk ok!
  370. [ 0.000000@0] Meson chip version = RevC (2B:C - 10:0)
  371. [ 0.000000@0] meson_g12a_sdemmc_init: register amlogic sdemmc clk
  372. [ 0.000000@0] meson_g12a_sdemmc_init: register amlogic sdemmc clk
  373. [ 0.000000@0] meson_g12a_gpu_init: register meson gpu clk
  374. [ 0.000000@0] meson_g12a_media_init: register meson media clk
  375. [ 0.000000@0] meson_g12a_misc_init: register amlogic g12a misc clks
  376. [ 0.000000@0] meson_g12a_misc_init: done.
  377. [ 0.000000@0] g12a_clkc_init initialization complete
  378. [ 0.000000@0] sm1 clk probe ok
  379. [ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (virt).
  380. [ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
  381. [ 0.000005@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
  382. [ 0.000019@0] Switching to timer-based delay loop, resolution 41ns
  383. [ 0.000054@0] meson_bc_timer: mclk->mux_reg =f080c190,mclk->reg =f080e194
  384. [ 0.000661@0] Console: colour dummy device 80x30
  385. [ 0.000685@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
  386. [ 0.000700@0] pid_max: default: 32768 minimum: 301
  387. [ 0.000774@0] thread_stack_cache_init, vmap:ed823900, bitmap:ed828400, cache page:cec00
  388. [ 0.000788@0] thread_stack_cache_init, allocation vm area:ed825040, addr:bc000000, size:3001000
  389. [ 0.000843@0] Security Framework initialized
  390. [ 0.000853@0] SELinux: Initializing.
  391. [ 0.000939@0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
  392. [ 0.000956@0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
  393. [ 0.001711@0] CPU: Testing write buffer coherency: ok
  394. [ 0.001749@0] ftrace: allocating 43159 entries in 127 pages
  395. [ 0.085131@0] sched-energy: CPU device node has no sched-energy-costs
  396. [ 0.085150@0] CPU0: update cpu_capacity 1024
  397. [ 0.085157@0] CPU0: thread 0, cpu 0, socket 0, mpidr 81000000
  398. [ 0.085185@0] Setting up static identity map for 0x200000 - 0x200058
  399. [ 0.128549@0] secmon: can't fine clear_range
  400. [ 0.177811@1] CPU1: update cpu_capacity 1024
  401. [ 0.177815@1] CPU1: thread 0, cpu 1, socket 0, mpidr 81000100
  402. [ 0.209900@2] CPU2: update cpu_capacity 1024
  403. [ 0.209904@2] CPU2: thread 0, cpu 2, socket 0, mpidr 81000200
  404. [ 0.242020@3] CPU3: update cpu_capacity 1024
  405. [ 0.242025@3] CPU3: thread 0, cpu 3, socket 0, mpidr 81000300
  406. [ 0.242125@0] Brought up 4 CPUs
  407. [ 0.242151@0] SMP: Total of 4 processors activated (192.00 BogoMIPS).
  408. [ 0.242157@0] CPU: All CPU(s) started in SVC mode.
  409. [ 0.243034@0] addr:bc045cce is in kernel, size fix 4096->10, data:mode=0755
  410. [ 0.243179@0] devtmpfs: initialized
  411. [ 0.269975@0] VFP support v0.3: implementor 41 architecture 3 part 40 variant 5 rev 2
  412. [ 0.270478@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
  413. [ 0.270501@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
  414. [ 0.270701@0] pinctrl core: initialized pinctrl subsystem
  415. [ 0.271911@0] NET: Registered protocol family 16
  416. [ 0.274964@0] DMA: preallocated 256 KiB pool for atomic coherent allocations
  417. [ 0.274975@0] schedtune: init normalization constants...
  418. [ 0.274980@0] schedtune: no energy model data
  419. [ 0.274985@0] schedtune: disabled!
  420. [ 0.289709@0] cpuidle: using governor menu
  421. [ 0.289815@0] register canvas platform driver
  422. [ 0.289887@0] register rdma platform driver
  423. [ 0.289937@0] aml_vdac_init: module init
  424. [ 0.292869@0] clkmsr: clkmsr: driver init
  425. [ 0.292877@0] codec_mm_module_init
  426. [ 0.292926@0] media_configs_system_init
  427. [ 0.293478@0] pstore: using zlib compression
  428. [ 0.294169@0] console [pstore-1] enabled
  429. [ 0.294214@0] pstore: Registered ramoops as persistent store backend
  430. [ 0.294227@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0
  431. [ 0.294239@0] ramoops: ramoops_io_en:0 1 old:0x0 ftrace_size:0x40000
  432. [ 0.296403@0] aml_iomap: amlogic iomap probe done
  433. [ 0.297000@0] vpu: driver version: v20190314(10-sm1)
  434. [ 0.297014@0] vpu: load vpu_clk: 666666667Hz(7)
  435. [ 0.297224@0] vpu: clktree_init
  436. [ 0.297302@0] vpu: vpu_probe OK
  437. [ 0.301816@0] clkmsr: msr_clk_reg0=f09c0004,msr_clk_reg2=f09c200c
  438. [ 0.301838@0] clkmsr: msr_ring_reg0=f09c45fc
  439. [ 0.307954@0] aml_vdac_probe:probe start.cpu_id:8,name:meson-sm1-vdac
  440. [ 0.308196@0] aml_vdac_probe: ok
  441. [ 0.308370@0] canvas_probe reg=ff638000,size=2000
  442. [ 0.308397@0] canvas maped reg_base =f09c6000
  443. [ 0.317268@0] rdma_probe,cpu_type:1, ver:0, len:8
  444. [ 0.317524@0] rdma_register, rdma_table_addr f09e9000 rdma_table_addr_phy cf040000 reg_buf edbc8000
  445. [ 0.317536@0] rdma_register success, handle 1 table_size 32768
  446. [ 0.317544@0] set_rdma_handle video rdma handle = 1.
  447. [ 0.318973@0] aml_snd_reg_map[0], reg:ff661000, size:400
  448. [ 0.318995@0] aml_snd_reg_map[1], reg:ff660000, size:1000
  449. [ 0.319015@0] aml_snd_reg_map[2], reg:ff661400, size:400
  450. [ 0.319035@0] aml_snd_reg_map[3], reg:ff662000, size:1000
  451. [ 0.319057@0] aml_snd_reg_map[4], reg:ffd01000, size:1000
  452. [ 0.319078@0] aml_snd_reg_map[5], reg:ff661800, size:400
  453. [ 0.319095@0] aml_snd_reg_map[6], reg:ff663800, size:30
  454. [ 0.319116@0] aml_snd_reg_map[7], reg:ff663c00, size:20
  455. [ 0.319134@0] aml_snd_reg_map[8], reg:ff663e00, size:10
  456. [ 0.319141@0] amlogic auge_snd_iomap probe done
  457. [ 0.321215@0] cvbs_out: cvbsout_probe, cpu_id:7,name:meson-sm1-cvbsout
  458. [ 0.321242@0] cvbs_out: clk path:0
  459. [ 0.321252@0] cvbs_out: error: failed to get vdac_config
  460. [ 0.321413@0] vout: vout1: register server: cvbs_vout_server
  461. [ 0.321424@0] cvbs_out: register cvbs module server ok
  462. [ 0.321436@0] vout: vout2: register server: cvbs_vout2_server
  463. [ 0.321445@0] cvbs_out: register cvbs module vout2 server ok
  464. [ 0.321455@0] cvbs_out: chrdev devno 264241152 for disp
  465. [ 0.321728@0] cvbs_out: create cdev cvbs
  466. [ 0.321737@0] cvbs_out: cvbsout_probe OK
  467. [ 0.322473@0] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma
  468. [ 0.322579@0] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma
  469. [ 0.322588@0] codec_mm_probe ok
  470. [ 0.568719@0] vgaarb: loaded
  471. [ 0.569041@0] SCSI subsystem initialized
  472. [ 0.569363@0] usbcore: registered new interface driver usbfs
  473. [ 0.569444@0] usbcore: registered new interface driver hub
  474. [ 0.569572@0] usbcore: registered new device driver usb
  475. [ 0.569725@0] Linux video capture interface: v2.00
  476. [ 0.569871@0] pps_core: LinuxPPS API ver. 1 registered
  477. [ 0.569880@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  478. [ 0.569913@0] PTP clock support registered
  479. [ 0.570748@0] secmon: reserve_mem_size:0x300000
  480. [ 0.570854@0] secmon secmon: assigned reserved memory node linux,secmon
  481. [ 0.571142@0] secmon: get page:ee597000, 5000
  482. [ 0.571154@0] secmon: share in base: 0xc50fe000, share out base: 0xc50ff000
  483. [ 0.571163@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
  484. [ 0.571724@0] fb: osd_init_module
  485. [ 0.572218@0] fb: viu vsync irq: 53
  486. [ 0.572241@0] fb: viu2 vsync irq: 61
  487. [ 0.572369@0] 0x000000d8:Y=d8,U=0,V=0
  488. [ 0.572379@0] 0x000000d9:Y=d9,U=0,V=0
  489. [ 0.572388@0] 0x000000da:Y=da,U=0,V=0
  490. [ 0.572398@0] 0x000000db:Y=db,U=0,V=0
  491. [ 0.572407@0] 0x000000dc:Y=dc,U=0,V=0
  492. [ 0.572417@0] 0x000000dd:Y=dd,U=0,V=0
  493. [ 0.572874@0] fb: osd_rdma_init: rdma_table p=0xcf048000,op=0xcf048000 , v=0xf0ad3000
  494. [ 0.572918@0] rdma_register, rdma_table_addr f0ad5000 rdma_table_addr_phy cf049000 reg_buf edb1e000
  495. [ 0.572930@0] rdma_register success, handle 2 table_size 4096
  496. [ 0.572941@0] fb: osd_rdma_init:osd rdma handle = 2.
  497. [ 0.572961@0] fb: mem_size: 0x800000
  498. [ 0.572969@0] fb: mem_size: 0x1980000
  499. [ 0.572977@0] fb: mem_size: 0x100000
  500. [ 0.572986@0] fb: mem_size: 0x100000
  501. [ 0.572995@0] fb: mem_size: 0x800000
  502. [ 0.573058@0] meson-fb fb: assigned reserved memory node linux,meson-fb
  503. [ 0.573070@0] fb: reserved memory base:0x7f800000, size:800000
  504. [ 0.573475@0] vout: error: invalid vinfo1. current vmode is not supported
  505. [ 0.573488@0] fb: init fbdev bpp is:32
  506. [ 0.575466@0] fb: set osd0 reverse as NONE
  507. [ 0.575492@0] vout: error: invalid vinfo1. current vmode is not supported
  508. [ 0.583378@0] fb: osd probe OK
  509. [ 0.584239@0] hdmitx: system: amhdmitx_probe start
  510. [ 0.584250@0] hdmitx: system: Ver: 20190624
  511. [ 0.584285@0] hdmitx: system: hdmitx_device.chip_type : 12
  512. [ 0.584328@0] hdmitx: system: not find match pwr-ctl
  513. [ 0.584374@0] hdmitx: system: not find drm_amhdmitx
  514. [ 0.584404@0] hdmitx: system: hpd irq = 48
  515. [ 0.584512@0] hdmitx: system: hdcp22_tx_skp failed to probe
  516. [ 0.584525@0] hdmitx: system: hdcp22_tx_esm failed to probe
  517. [ 0.585035@0] vout: vout1: register server: hdmitx_vout_server
  518. [ 0.585047@0] vout: vout2: register server: hdmitx_vout2_server
  519. [ 0.585807@0] hdmitx: hdmitx20: Mapped PHY: 0xffd00000
  520. [ 0.585833@0] hdmitx: hdmitx20: Mapped PHY: 0xff634400
  521. [ 0.585852@0] hdmitx: hdmitx20: Mapped PHY: 0xff900000
  522. [ 0.585878@0] hdmitx: hdmitx20: Mapped PHY: 0xff800000
  523. [ 0.585890@0] hdmitx: hdmitx20: Mapped PHY: 0xff63c000
  524. [ 0.585900@0] hdmitx: hdmitx20: Mapped PHY: 0xffd00000
  525. [ 0.585911@0] hdmitx: hdmitx20: Mapped PHY: 0xff608000
  526. [ 0.585924@0] hdmitx: hdmitx20: Mapped PHY: 0xff600000
  527. [ 0.585937@0] hdmitx: hdmitx20: Mapped PHY: 0xffe01000
  528. [ 0.585956@0] hdmitx: hw: hdmitx_get_format:0x0
  529. [ 0.585965@0] hdmitx: hw: P_HHI_HDMI_CLK_CNTL :0x100
  530. [ 0.585974@0] hdmitx: hw: P_HHI_HDMI_PLL_CNTL :0xda0504f7
  531. [ 0.586213@0] hdmitx: hw: avmute set to 1
  532. [ 0.586225@0] hdmitx: system: fmt_attr rgb,8bit
  533. [ 0.586339@0] hdmitx: system: amhdmitx_probe end
  534. [ 0.587336@0] vout: create vout attribute OK
  535. [ 0.587572@0] vout: vout_fops_create OK
  536. [ 0.587583@0] vout: vout1: register server: nulldisp_vout_server
  537. [ 0.587716@0] vout: tvout monitor interval:500(ms), timeout cnt:20
  538. [ 0.587757@0] cvbs_out: mode is 1,sync_duration_den=1,sync_duration_num=50
  539. [ 0.587791@0] cvbs_out: vdac open.0 = 0x8f6001, 0x0
  540. [ 0.587803@0]
  541. [ 0.587803@0] vdac_enable: on:1,module_sel:8
  542. [ 0.587817@0] cvbs_out: already display in uboot
  543. [ 0.587827@0] vout: init mode 576cvbs set ok
  544. [ 0.587837@0] vout: aml_tvout_mode_monitor
  545. [ 0.587859@0] vout: aml_vout_probe OK
  546. [ 0.588519@0] chip type:0x2b
  547. [ 0.588918@0] NO valid ramdump args:0 0
  548. [ 0.591336@3] Advanced Linux Sound Architecture Driver Initialized.
  549. [ 0.592227@3] Bluetooth: Core ver 2.22
  550. [ 0.592364@3] NET: Registered protocol family 31
  551. [ 0.592376@3] Bluetooth: HCI device and connection manager initialized
  552. [ 0.592394@3] Bluetooth: HCI socket layer initialized
  553. [ 0.592412@3] Bluetooth: L2CAP socket layer initialized
  554. [ 0.592461@3] Bluetooth: SCO socket layer initialized
  555. [ 0.593299@3] NetLabel: Initializing
  556. [ 0.593328@3] NetLabel: domain hash size = 128
  557. [ 0.593337@3] NetLabel: protocols = UNLABELED CIPSOv4
  558. [ 0.593425@3] NetLabel: unlabeled traffic allowed by default
  559. [ 0.598266@3] clocksource: Switched to clocksource arch_sys_counter
  560. [ 0.683930@3] VFS: Disk quotas dquot_6.6.0
  561. [ 0.684073@3] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  562. [ 0.700201@3] dtv_dmd:[amldtvdemod..]aml_dtvdemod_init.
  563. [ 0.700233@3] jtag: module init
  564. [ 0.700739@3] NET: Registered protocol family 2
  565. [ 0.701637@3] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
  566. [ 0.701708@3] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
  567. [ 0.701790@3] TCP: Hash tables configured (established 8192 bind 8192)
  568. [ 0.701906@3] UDP hash table entries: 512 (order: 2, 16384 bytes)
  569. [ 0.701960@3] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  570. [ 0.702166@3] NET: Registered protocol family 1
  571. [ 0.705146@3] wifi: power_on_pin_OD = 0;
  572. [ 0.705191@3] aml_wifi wifi: [wifi_dev_probe] no power_on_pin2
  573. [ 0.705420@3] aml_wifi wifi: [pwm_double_channel_conf_dt] wifi pwm dt ok
  574. [ 0.705464@3] aml_wifi wifi: [pwm_double_channel_conf] wifi pwm conf ok
  575. [ 0.705479@3] aml_wifi wifi: [wifi_dev_probe] dhd_static_buf setup
  576. [ 0.705490@3] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem 1.579.77.41.9
  577. [ 0.706543@3] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem prealloc ok
  578. [ 0.706564@3] aml_wifi wifi: [wifi_dev_probe] interrupt_pin=483
  579. [ 0.706577@3] aml_wifi wifi: [wifi_dev_probe] irq_num=0, irq_trigger_type=1
  580. [ 0.706588@3] aml_wifi wifi: [wifi_dev_probe] power_on_pin=482
  581. [ 0.706600@3] aml_wifi wifi: [wifi_dev_probe] clock_32k_pin=0
  582. [ 0.707062@2] aml_wifi wifi: [wifi_setup_dt] wifi_setup_dt
  583. [ 0.707242@2] aml_wifi wifi: [wifi_setup_dt] irq num is:(73)
  584. [ 0.707256@2] aml_wifi wifi: [wifi_setup_dt] interrupt_pin(483)
  585. [ 0.707288@2] aml_wifi wifi: [wifi_setup_dt] power_on_pin(482)
  586. [ 0.711258@2] enable_pmuserenr_all() start
  587. [ 0.711298@2] enable_pmuserenr_all() end
  588. [ 0.711332@2] hw perfevents: clusterb_enabled = 0
  589. [ 0.711346@2] hw perfevents: cpumasks 0xf, 0x0
  590. [ 0.711408@2] hw perfevents: cluster A irq = 25
  591. [ 0.711552@2] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
  592. [ 0.717102@3] audit: initializing netlink subsys (disabled)
  593. [ 0.717265@3] audit: type=2000 audit(0.656:1): initialized
  594. [ 0.718947@2] workingset: timestamp_bits=30 max_order=20 bucket_order=0
  595. [ 0.730123@1] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  596. [ 0.730591@1] exFAT: Version 1.2.9
  597. [ 0.732014@1] Registering sdcardfs 0.1
  598. [ 0.732395@1] ntfs: driver 2.1.32 [Flags: R/O].
  599. [ 0.732779@1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
  600. [ 0.733965@3] fuse init (API version 7.26)
  601. [ 0.742325@3] NET: Registered protocol family 38
  602. [ 0.742383@3] Key type asymmetric registered
  603. [ 0.742398@3] Asymmetric key parser 'x509' registered
  604. [ 0.742608@3] bounce: pool size: 64 pages
  605. [ 0.743041@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
  606. [ 0.743058@3] io scheduler noop registered (default)
  607. [ 0.743069@3] io scheduler deadline registered
  608. [ 0.743127@3] io scheduler cfq registered
  609. [ 0.755543@0] clear:2a000000, free:2a000000, tick:162040 us
  610. [ 0.758396@2] random: fast init done
  611. [ 0.758452@2] random: crng init done
  612. [ 0.770955@3] brd: module loaded
  613. [ 0.777584@3] loop: module loaded
  614. [ 0.778788@3] zram: Added device: zram0
  615. [ 0.779191@3] mtdoops: mtd device (mtddev=name/number) must be supplied
  616. [ 0.780222@3] libphy: Fixed MDIO Bus: probed
  617. [ 0.780512@3] tun: Universal TUN/TAP device driver, 1.6
  618. [ 0.780523@3] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  619. [ 0.781503@3] REG0:Addr = f0cfc540
  620. [ 0.781526@3] Not set cali_val for REG1
  621. [ 0.782029@3] meson6-dwmac ff3f0000.ethernet: no reset control found
  622. [ 0.782043@3] stmmac - user ID: 0x11, Synopsys ID: 0x37
  623. [ 0.782052@3] Ring mode enabled
  624. [ 0.782062@3] DMA HW capability register supported
  625. [ 0.782073@3] Normal descriptors
  626. [ 0.782080@3] RX Checksum Offload Engine supported
  627. [ 0.782089@3] COE Type 2
  628. [ 0.782097@3] TX Checksum insertion supported
  629. [ 0.782105@3] Wake-Up On Lan supported
  630. [ 0.782172@3] Enable RX Mitigation via HW Watchdog Timer
  631. [ 0.785559@3] libphy: stmmac: probed
  632. [ 0.785576@3] eth%d: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
  633. [ 0.785586@3] eth%d: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
  634. [ 0.787174@3] PPP generic driver version 2.4.2
  635. [ 0.787437@3] PPP BSD Compression module registered
  636. [ 0.787449@3] PPP Deflate Compression module registered
  637. [ 0.787476@3] PPP MPPE Compression module registered
  638. [ 0.787485@3] NET: Registered protocol family 24
  639. [ 0.787598@3] usbcore: registered new interface driver asix
  640. [ 0.787711@3] usbcore: registered new interface driver ax88179_178a
  641. [ 0.787797@3] usbcore: registered new interface driver cdc_ether
  642. [ 0.787867@3] usbcore: registered new interface driver net1080
  643. [ 0.787931@3] usbcore: registered new interface driver cdc_subset
  644. [ 0.787995@3] usbcore: registered new interface driver zaurus
  645. [ 0.788082@3] usbcore: registered new interface driver cdc_ncm
  646. [ 0.788741@3] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  647. [ 0.788754@3] ehci-pci: EHCI PCI platform driver
  648. [ 0.788820@3] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  649. [ 0.788853@3] ohci-pci: OHCI PCI platform driver
  650. [ 0.789487@3] usbcore: registered new interface driver cdc_acm
  651. [ 0.789497@3] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  652. [ 0.789581@3] usbcore: registered new interface driver usb-storage
  653. [ 0.789700@3] usbcore: registered new interface driver usbserial
  654. [ 0.790154@3] mousedev: PS/2 mouse device common for all mice
  655. [ 0.790492@3] usbcore: registered new interface driver xpad
  656. [ 0.790674@3] i2c /dev entries driver
  657. [ 0.790961@3] IR NEC protocol handler initialized
  658. [ 0.790971@3] IR RC5(x/sz) protocol handler initialized
  659. [ 0.790979@3] IR RC6 protocol handler initialized
  660. [ 0.790987@3] IR JVC protocol handler initialized
  661. [ 0.790995@3] IR Sony protocol handler initialized
  662. [ 0.791004@3] IR SANYO protocol handler initialized
  663. [ 0.791013@3] IR Sharp protocol handler initialized
  664. [ 0.791020@3] IR MCE Keyboard/mouse protocol handler initialized
  665. [ 0.791030@3] IR XMP protocol handler initialized
  666. [ 0.791126@3] usbcore: registered new interface driver uvcvideo
  667. [ 0.791134@3] USB Video Class driver (1.1.1)
  668. [ 0.791205@3] usbcore: registered new interface driver cx231xx
  669. [ 0.791217@3] md: linear personality registered for level -1
  670. [ 0.791822@3] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
  671. [ 0.791834@3] Bluetooth: HCI UART driver ver 2.3
  672. [ 0.791845@3] Bluetooth: HCI UART protocol H4 registered
  673. [ 0.792160@3] cpuidle: enable-method property 'psci' found operations
  674. [ 0.792304@3] cpuidle: enable-method property 'psci' found operations
  675. [ 0.792446@3] cpuidle: enable-method property 'psci' found operations
  676. [ 0.792561@3] cpuidle: enable-method property 'psci' found operations
  677. [ 0.793837@0] ledtrig-cpu: registered to indicate activity on CPUs
  678. [ 0.794321@0] hidraw: raw HID events driver (C) Jiri Kosina
  679. [ 0.794776@0] usbcore: registered new interface driver usbhid
  680. [ 0.794788@0] usbhid: USB HID core driver
  681. [ 0.794993@0] ashmem: initialized
  682. [ 0.796317@0] value of voltage_tolerance 0
  683. [ 0.797646@0] cpu cpu0: meson_cpufreq_init: CPU 0 initialized
  684. [ 0.799455@0] ff803000.serial: clock gate not found
  685. [ 0.799502@0] meson_uart ff803000.serial: ==uart0 reg addr = f0e9c000
  686. [ 0.799546@0] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 32, base_baud = 1500000) is a meson_uart
  687. [ 0.799565@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200
  688. [ 2.943317@0] console [ttyS0] enabled
  689. [ 2.947917@0] meson_uart ffd24000.serial: ==uart1 reg addr = f0e9e000
  690. [ 2.953448@0] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 47, base_baud = 1500000) is a meson_uart
  691. [ 2.964528@0] amlogic-new-usb2-v2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xf0ed2000
  692. [ 2.973505@0] amlogic-new-usb3-v2 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xf0edd080
  693. [ 2.984328@0] Error: Driver 'meson_reset' is already registered, aborting...
  694. [ 2.990545@0] aml_dma ff63e000.aml_dma: Aml dma
  695. [ 2.996545@0] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma
  696. [ 3.003454@0] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma
  697. [ 3.007977@0] meson-remote: Driver init
  698. [ 3.011597@0] meson-remote: remote_probe
  699. [ 3.015375@0] meson-remote ff808040.rc: protocol = 0x1
  700. [ 3.020445@0] meson-remote ff808040.rc: led_blink = 1
  701. [ 3.025463@0] meson-remote ff808040.rc: led_blink_frq = 100
  702. [ 3.031125@0] meson-remote ff808040.rc: platform_data irq =46
  703. [ 3.036878@0] meson-remote ff808040.rc: custom_number = 4
  704. [ 3.042216@0] meson-remote ff808040.rc: ptable->map_size = 50
  705. [ 3.047908@0] meson-remote ff808040.rc: ptable->custom_name = amlogic-remote-1
  706. [ 3.055123@0] meson-remote ff808040.rc: ptable->custom_code = 0xfb04
  707. [ 3.061430@0] meson-remote ff808040.rc: ptable->release_delay = 80
  708. [ 3.067613@0] meson-remote ff808040.rc: ptable->map_size = 28
  709. [ 3.073321@0] meson-remote ff808040.rc: ptable->custom_name = amlogic-remote-2
  710. [ 3.080499@0] meson-remote ff808040.rc: ptable->custom_code = 0xfe01
  711. [ 3.086819@0] meson-remote ff808040.rc: ptable->release_delay = 80
  712. [ 3.092990@0] meson-remote ff808040.rc: ptable->tab.cursor_code.fn_key_scancode = 0x0
  713. [ 3.100861@0] meson-remote ff808040.rc: ptable->tab.cursor_code.cursor_left_scancode = 0x51
  714. [ 3.109268@0] meson-remote ff808040.rc: ptable->tab.cursor_code.cursor_right_scancode = 0x50
  715. [ 3.117778@0] meson-remote ff808040.rc: ptable->tab.cursor_code.cursor_up_scancode = 0x16
  716. [ 3.125995@0] meson-remote ff808040.rc: ptable->tab.cursor_code.cursor_down_scancode = 0x1a
  717. [ 3.134430@0] meson-remote ff808040.rc: ptable->tab.cursor_code.cursor_ok_scancode = 0x13
  718. [ 3.142650@0] meson-remote ff808040.rc: ptable->map_size = 17
  719. [ 3.148356@0] meson-remote ff808040.rc: ptable->custom_name = amlogic-remote-3
  720. [ 3.155563@0] meson-remote ff808040.rc: ptable->custom_code = 0xbd02
  721. [ 3.161925@0] meson-remote ff808040.rc: ptable->release_delay = 80
  722. [ 3.168048@0] meson-remote ff808040.rc: ptable->map_size = 12
  723. [ 3.173764@0] meson-remote ff808040.rc: ptable->custom_name = amlogic-remote-4
  724. [ 3.180942@0] meson-remote ff808040.rc: ptable->custom_code = 0x7f80
  725. [ 3.187267@0] meson-remote ff808040.rc: ptable->release_delay = 80
  726. [ 3.193438@0] meson-remote ff808040.rc: ptable->tab.cursor_code.fn_key_scancode = 0x48
  727. [ 3.201392@0] meson-remote ff808040.rc: ptable->tab.cursor_code.cursor_left_scancode = 0x37
  728. [ 3.209800@0] meson-remote ff808040.rc: ptable->tab.cursor_code.cursor_right_scancode = 0x39
  729. [ 3.218365@0] meson-remote ff808040.rc: ptable->tab.cursor_code.cursor_up_scancode = 0x38
  730. [ 3.226531@0] meson-remote ff808040.rc: ptable->tab.cursor_code.cursor_down_scancode = 0x40
  731. [ 3.234950@0] meson-remote ff808040.rc: ptable->tab.cursor_code.cursor_ok_scancode = 0x13
  732. [ 3.243173@0] meson-remote ff808040.rc: default protocol = 0x1 and id = 0
  733. [ 3.249927@0] meson-remote ff808040.rc: reg=0x0, val=0x1f40190
  734. [ 3.255749@0] meson-remote ff808040.rc: reg=0x4, val=0x12c00c8
  735. [ 3.261541@0] meson-remote ff808040.rc: reg=0x8, val=0x960050
  736. [ 3.267260@0] meson-remote ff808040.rc: reg=0xc, val=0x480028
  737. [ 3.272995@0] meson-remote ff808040.rc: reg=0x10, val=0x70fa0013
  738. [ 3.278963@0] meson-remote ff808040.rc: reg=0x18, val=0x8616800
  739. [ 3.284853@0] meson-remote ff808040.rc: reg=0x1c, val=0x9f00
  740. [ 3.290486@0] meson-remote ff808040.rc: reg=0x20, val=0x0
  741. [ 3.295876@0] meson-remote ff808040.rc: reg=0x24, val=0x0
  742. [ 3.301233@0] meson-remote ff808040.rc: reg=0x28, val=0x0
  743. [ 3.307680@0] input: aml_keypad as /devices/platform/ff808040.rc/input/input0
  744. [ 3.315576@0] meson-remote: IR XMP protocol handler initialized
  745. [ 3.322389@0] ion_dev soc:ion_dev: assigned reserved memory node linux,ion-dev
  746. [ 3.327292@0] ge2d: ge2d_init_module
  747. [ 3.330650@0] ge2d: ge2d_dev major:237
  748. [ 3.334470@0] ge2d: clock source clk_ge2d_gate cdfa93c0
  749. [ 3.339318@0] ge2d: clock clk_ge2d source cdfa9440
  750. [ 3.344062@0] ge2d: clock source clk_vapb_0 cdfa94c0
  751. [ 3.348986@0] ge2d: ge2d init clock is 500000000 HZ, VPU clock is 666666656 HZ
  752. [ 3.356308@0] ge2d: ge2d clock is 499 MHZ
  753. [ 3.360183@0] ge2d: find address resource
  754. [ 3.364168@0] ge2d: map io source 0xff940000,size=65536 to 0xf1010000
  755. [ 3.370570@0] ge2d: reserved mem init failed
  756. [ 3.374839@0] ge2d: ge2d: pdev=edb9b600, irq=52, clk=cdfa93c0
  757. [ 3.380570@0] ge2d: ge2d start monitor
  758. [ 3.384372@1] ge2d: ge2d workqueue monitor start
  759. [ 3.384782@0] [tsync_pcr_init]init success.
  760. [ 3.384975@0] amvideom vsync irq: 53
  761. [ 3.385621@0] hdmitx: hdcp: hdmitx_hdcp_init
  762. [ 3.386151@0] vout: vout2: create vout2 attribute OK
  763. [ 3.386301@0] vout: vout2: vout2_fops_create OK
  764. [ 3.386470@0] vout: vout2: clktree_init
  765. [ 3.386473@0] vout: vout2: register server: nulldisp_vout2_server
  766. [ 3.386592@0] vout: vout2: init mode null set ok
  767. [ 3.386594@0] vout: vout2: aml_vout2_probe OK
  768. [ 3.386706@0] DI: di_module_init ok.
  769. [ 3.386711@0] DI: di_module_init: major 511
  770. [ 3.387096@0] deinterlace deinterlace: assigned reserved memory node linux,di_cma
  771. [ 3.387101@0] di:flag_cma=1
  772. [ 3.387103@0] DI: CMA size 0x2800000.
  773. [ 3.387120@0] pre_irq:69
  774. [ 3.387128@0] post_irq:70
  775. [ 3.387131@0] DI: di_probe allocate rdma channel 0.
  776. [ 3.387137@0] di_get_vpu_clkb: get clk vpu error.
  777. [ 3.387140@0] DI: vpu clkb <334000000, 667000000>
  778. [ 3.387170@0] get clkb rate:333333328
  779. [ 3.387176@0] DI:enable vpu clkb.
  780. [ 3.387190@0] 0x000000de:Y=de,U=0,V=0
  781. [ 3.387193@0] 0x000000df:Y=df,U=0,V=0
  782. [ 3.387194@0] 0x000000e0:Y=e0,U=0,V=0
  783. [ 3.387197@0] 0x000000e1:Y=e1,U=0,V=0
  784. [ 3.387199@0] 0x000000e2:Y=e2,U=0,V=0
  785. [ 3.387201@0] 0x000000e3:Y=e3,U=0,V=0
  786. [ 3.387203@0] 0x000000f0:Y=f0,U=0,V=0
  787. [ 3.387206@0] 0x000000f1:Y=f1,U=0,V=0
  788. [ 3.387207@0] 0x000000f2:Y=f2,U=0,V=0
  789. [ 3.387208@0] 0x000000f3:Y=f3,U=0,V=0
  790. [ 3.387213@0] 0x000000f4:Y=f4,U=0,V=0
  791. [ 3.387215@0] 0x000000f5:Y=f5,U=0,V=0
  792. [ 3.387216@0] 0x000000f6:Y=f6,U=0,V=0
  793. [ 3.387217@0] 0x000000f7:Y=f7,U=0,V=0
  794. [ 3.387218@0] 0x000000f8:Y=f8,U=0,V=0
  795. [ 3.387220@0] 0x000000f9:Y=f9,U=0,V=0
  796. [ 3.387226@0] 0x000000fa:Y=fa,U=0,V=0
  797. [ 3.387227@0] 0x000000fb:Y=fb,U=0,V=0
  798. [ 3.387228@0] 0x000000fc:Y=fc,U=0,V=0
  799. [ 3.387229@0] 0x000000fd:Y=fd,U=0,V=0
  800. [ 3.387231@0] 0x000000fe:Y=fe,U=0,V=0
  801. [ 3.387232@0] 0x000000ff:Y=ff,U=0,V=0
  802. [ 3.387236@0] 0x0000003a:Y=3a,U=0,V=0
  803. [ 3.387237@0] 0x0000003b:Y=3b,U=0,V=0
  804. [ 3.387238@0] 0x0000003c:Y=3c,U=0,V=0
  805. [ 3.387240@0] DI: support multi decoding 58~59~60.
  806. [ 3.387437@0] DI: di_probe:Di use HRTIMER
  807. [ 3.387547@0] di_probe:ok
  808. [ 3.387630@0] vdin_drv_init: major 510
  809. [ 3.387867@0] vdin_drv_init: vdin driver init done
  810. [ 3.387870@0] [viuin..]viuin_init_module viuin module init
  811. [ 3.388105@0] [viuin..]viuin_probe probe ok.
  812. [ 3.388630@0] [RX]-hdmirx: hdmirx_init.
  813. [ 3.388632@0] ESM HLD: Initializing...
  814. [ 3.388762@0] tvin_afe: tvafe_drv_init: major 508
  815. [ 3.389076@0] tvin_afe: tvafe_drv_init.
  816. [ 3.389242@0] tvafe_vbi: vbi: vbi_init.
  817. [ 3.389443@0] amvdec_csi module: init.
  818. [ 3.389448@0] amvdec_csi_init_module:major 506
  819. [ 3.389596@0] amvdec_csi module: init. ok
  820. [ 3.389600@0] amlvid:info: amlvideo_init called
  821. [ 3.389601@0] amlvid:info: amlvideo_create_instance called
  822. [ 3.389604@0] amlvid:info: v4l2_dev.name=:amlvideo-000
  823. [ 3.389784@0] amlvideo-000: V4L2 device registered as video10
  824. [ 3.389785@0] amlvid:info: amlvideo_create_instance called
  825. [ 3.389788@0] amlvid:info: v4l2_dev.name=:amlvideo-001
  826. [ 3.389903@0] amlvideo-001: V4L2 device registered as video23
  827. [ 3.390055@0] PPMGRDRV: warn: ppmgr module init func called
  828. [ 3.390177@0] PPMGRDRV: err: ppmgr_driver_probe called
  829. [ 3.390286@0] PPMGRDRV: info: ppmgr_dev major:505
  830. [ 3.390501@0] ppmgr: probe of ppmgr failed with error -22
  831. [ 3.390953@0] ionvideo-000: V4L2 device registered as video13
  832. [ 3.391076@0] ionvideo-001: V4L2 device registered as video14
  833. [ 3.391185@0] ionvideo-002: V4L2 device registered as video15
  834. [ 3.391290@0] ionvideo-003: V4L2 device registered as video16
  835. [ 3.391408@0] ionvideo-004: V4L2 device registered as video17
  836. [ 3.391524@0] ionvideo-005: V4L2 device registered as video18
  837. [ 3.391632@0] ionvideo-006: V4L2 device registered as video19
  838. [ 3.391740@0] ionvideo-007: V4L2 device registered as video20
  839. [ 3.391860@0] ionvideo-008: V4L2 device registered as video21
  840. [ 3.391862@0] ionvid: info: Video Technology Magazine Ion Video
  841. [ 3.391863@0] ionvid: info: Capture Board ver 1.0 successfully loaded
  842. [ 3.392181@0] picdec: picdec_driver_probe called.
  843. [ 3.392399@0] picdec: probe of picdec failed with error -22
  844. [ 3.392600@0] videosync_create_instance dev_s ed07d400,dev_s->dev ed0bccc0
  845. [ 3.392602@0] videosync_create_instance reg videosync.0
  846. [ 3.392682@0] aml_vecm_init:module init
  847. [ 3.392686@2] videosync_thread started
  848. [ 3.392898@0]
  849. [ 3.392898@0] VECM probe start
  850. [ 3.393156@0] vlock_status_init vlock_en:0
  851. [ 3.393180@0] Can't find wb_sel.
  852. [ 3.393182@0] hdr:Can't find cfg_en_osd_100.
  853. [ 3.393188@0] amlogic, vecm
  854. [ 3.393188@0] vlock dt support: 1
  855. [ 3.393189@0] vlock dt new_fsm: 0
  856. [ 3.393190@0] vlock dt hwver: 0
  857. [ 3.393191@0] vlock dt phlock_en: 0
  858. [ 3.393193@0] Can't find vlock_en.
  859. [ 3.393194@0] Can't find vlock_mode.
  860. [ 3.393196@0] Can't find vlock_pll_m_limit.
  861. [ 3.393197@0] Can't find vlock_line_limit.
  862. [ 3.393220@0] param_config vlock_en:0
  863. [ 3.393226@0] aml_vecm_probe: ok
  864. [ 3.393278@0] amdolby_vision_init:module init
  865. [ 3.393629@0]
  866. [ 3.393629@0] amdolby_vision probe start & ver: 20181220
  867. [ 3.393637@0]
  868. [ 3.393637@0] cpu_id=2 tvmode=0
  869. [ 3.393792@0] dolby_vision_init_receiver(dvel)
  870. [ 3.393796@0] dolby_vision_init_receiver: dvel
  871. [ 3.396706@0] amdolby_vision_probe: ok
  872. [ 3.396784@0] prime_sl module init
  873. [ 3.397246@0] vm_init .
  874. [ 3.398191@0] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller
  875. [ 3.399158@0] meson-mmc: >>>>>>>>hostbase f1021000, dmode
  876. [ 3.399449@0] meson-mmc: actual_clock :400000, HHI_nand: 0x80
  877. [ 3.399452@0] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c
  878. [ 3.438270@0] meson-mmc: meson_mmc_probe() : success!
  879. [ 3.440559@2] meson-mmc: >>>>>>>>hostbase f10ab000, dmode
  880. [ 3.440614@2] meson-mmc: gpio_cd = 1ca
  881. [ 3.483292@2] meson-mmc: meson_mmc_probe() : success!
  882. [ 3.485244@0] meson-mmc: >>>>>>>>hostbase f1135000, dmode
  883. [ 3.485533@0] meson-mmc: actual_clock :400000, HHI_nand: 0x80
  884. [ 3.485536@0] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c
  885. [ 3.526271@0] meson-mmc: meson_mmc_probe() : success!
  886. [ 3.526769@0] amlogic mtd driver init
  887. [ 3.527625@0] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0
  888. [ 3.528557@0] cectx ff80023c.aocec: cec driver date:2019/6/13:early suspend not report pw status
  889. [ 3.528557@0]
  890. [ 3.528833@0] cectx ff80023c.aocec: compatible:amlogic, aocec-sm1
  891. [ 3.528836@0] cectx ff80023c.aocec: cecb_ver:0x2
  892. [ 3.528839@0] cectx ff80023c.aocec: line_reg:0x1
  893. [ 3.528843@0] cectx ff80023c.aocec: line_bit:0x3
  894. [ 3.528845@0] cectx ff80023c.aocec: ee_to_ao:0x1
  895. [ 3.529014@0] input: cec_input as /devices/virtual/input/input1
  896. [ 3.529193@2] cectx ff80023c.aocec: not find 'port_num'
  897. [ 3.529199@2] cectx ff80023c.aocec: using cec:1
  898. [ 3.529227@2] cectx ff80023c.aocec: no hdmirx regs
  899. [ 3.529230@2] cectx ff80023c.aocec: no hhi regs
  900. [ 3.529239@2] cectx ff80023c.aocec: not find 'output'
  901. [ 3.529246@2] cec: wake up flag:0
  902. [ 3.530714@2] cectx ff80023c.aocec: irq cnt:2
  903. [ 3.530955@2] cectx ff80023c.aocec: wakeup_reason:0x0
  904. [ 3.531049@0] cectx ff80023c.aocec: cev val1: 0x0;val2: 0x0
  905. [ 3.531055@0] cectx ff80023c.aocec: aml_cec_probe success end
  906. [ 3.531441@0] unifykey: storage in base: 0xc5000000
  907. [ 3.531442@0] unifykey: storage out base: 0xc5040000
  908. [ 3.531445@0] unifykey: storage block base: 0xc5080000
  909. [ 3.531446@0] unifykey: probe done!
  910. [ 3.531912@0] unifykey: no efuse-version set, use default value: -1
  911. [ 3.531914@0] unifykey: key unify config unifykey-num is 16
  912. [ 3.531986@0] unifykey: key unify fact unifykey-num is 16
  913. [ 3.531993@0] unifykey: unifykey_devno: 1f200000
  914. [ 3.532384@0] unifykey: device unifykeys created ok
  915. [ 3.532473@0] unifykey: aml_unifykeys_init done!
  916. [ 3.532662@0] meson ts init
  917. [ 3.532714@0] tsensor id: 0
  918. [ 3.532887@0] tsensor trim info: 0xfa0080ca!
  919. [ 3.532890@0] tsensor hireboot: 0xc0ff2af0
  920. [ 3.532965@0] meson ts init
  921. [ 3.532986@0] tsensor id: 1
  922. [ 3.533112@0] tsensor trim info: 0xfa0080a7!
  923. [ 3.533114@0] tsensor hireboot: 0xc0ff2ae0
  924. [ 3.533268@0] audio_dsp: [dsp]register dsp to char divece(257)
  925. [ 3.533527@0] amaudio: amaudio: driver amaudio init!
  926. [ 3.534068@0] amaudio: amaudio_init - amaudio: driver amaudio succuess!
  927. [ 3.534869@0] sysled: module init
  928. [ 3.535220@0] meson_wdt ffd0f0d0.watchdog: start watchdog
  929. [ 3.535224@0] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog
  930. [ 3.535554@0] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done
  931. [ 3.536300@0] amlogic rfkill init
  932. [ 3.536442@0] enter bt_probe of_node
  933. [ 3.536462@0] not get gpio_en
  934. [ 3.536472@0] power on valid level is high
  935. [ 3.536472@0] bt: power_on_pin_OD = 0;
  936. [ 3.536474@0] bt: power_off_flag = 1;
  937. [ 3.536476@0] dis power down = 0;
  938. [ 3.539674@0] meson-aml-mmc ffe07000.emmc: divider requested rate 52000000 != actual rate 50000000: ret=0
  939. [ 3.539677@0] meson-mmc: actual_clock :50000000, HHI_nand: 0x80
  940. [ 3.539680@0] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000354
  941. [ 3.539775@0] meson-aml-mmc ffe07000.emmc: divider requested rate 52000000 != actual rate 50000000: ret=0
  942. [ 3.539779@0] meson-mmc: actual_clock :50000000, HHI_nand: 0x80
  943. [ 3.539782@0] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000354
  944. [ 3.539995@0] emmc: new high speed MMC card at address 0001
  945. [ 3.540481@0] emmc: clock 50000000, 8-bit-bus-width
  946. [ 3.540481@0]
  947. [ 3.540481@0] mmcblk0: emmc:0001 CWBD3R 58.2 GiB
  948. [ 3.544710@0] mmcblk0boot0: emmc:0001 CWBD3R partition 1 4.00 MiB
  949. [ 3.544922@0] mmcblk0boot1: emmc:0001 CWBD3R partition 2 4.00 MiB
  950. [ 3.545122@0] mmcblk0rpmb: emmc:0001 CWBD3R partition 3 4.00 MiB
  951. [ 3.546093@0] meson-mmc: Enter aml_emmc_partition_ops
  952. [ 3.546686@0] meson-mmc: [mmc_read_partition_tbl] mmc read partition OK!
  953. [ 3.546689@0] meson-mmc: add_emmc_partition
  954. [ 3.546867@0] meson-mmc: [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
  955. [ 3.547012@0] meson-mmc: [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
  956. [ 3.547139@0] meson-mmc: [mmcblk0p03] cache offset 0x000006c00000, size 0x000046000000
  957. [ 3.547274@0] meson-mmc: [mmcblk0p04] env offset 0x00004d400000, size 0x000000800000
  958. [ 3.547396@0] meson-mmc: [mmcblk0p05] logo offset 0x00004e400000, size 0x000000800000
  959. [ 3.547539@0] meson-mmc: [mmcblk0p06] recovery offset 0x00004f400000, size 0x000001800000
  960. [ 3.547672@0] meson-mmc: [mmcblk0p07] misc offset 0x000051400000, size 0x000000800000
  961. [ 3.547805@0] meson-mmc: [mmcblk0p08] dtbo offset 0x000052400000, size 0x000000800000
  962. [ 3.547951@0] meson-mmc: [mmcblk0p09] cri_data offset 0x000053400000, size 0x000000800000
  963. [ 3.548073@0] meson-mmc: [mmcblk0p10] param offset 0x000054400000, size 0x000001000000
  964. [ 3.548193@0] meson-mmc: [mmcblk0p11] boot offset 0x000055c00000, size 0x000001000000
  965. [ 3.548320@0] meson-mmc: [mmcblk0p12] rsv offset 0x000057400000, size 0x000001000000
  966. [ 3.548446@0] meson-mmc: [mmcblk0p13] metadata offset 0x000058c00000, size 0x000001000000
  967. [ 3.548578@0] meson-mmc: [mmcblk0p14] vbmeta offset 0x00005a400000, size 0x000000200000
  968. [ 3.548697@0] meson-mmc: [mmcblk0p15] tee offset 0x00005ae00000, size 0x000002000000
  969. [ 3.548837@0] meson-mmc: [mmcblk0p16] vendor offset 0x00005d600000, size 0x000014000000
  970. [ 3.548971@0] meson-mmc: [mmcblk0p17] odm offset 0x000071e00000, size 0x000008000000
  971. [ 3.549096@0] meson-mmc: [mmcblk0p18] system offset 0x00007a600000, size 0x000074000000
  972. [ 3.549226@0] meson-mmc: [mmcblk0p19] product offset 0x0000eee00000, size 0x000008000000
  973. [ 3.549353@0] meson-mmc: [mmcblk0p20] data offset 0x0000f7600000, size 0x000d98200000
  974. [ 3.549370@0] card key: card_blk_probe.
  975. [ 3.549383@0] emmc_key_init:183 emmc key lba_start:0x12020,lba_end:0x12220
  976. [ 3.549385@0] emmc key: emmc_key_init:205 ok.
  977. [ 3.555548@0] meson-mmc: amlmmc_dtb_init: register dtb chardev
  978. [ 3.555549@0] meson-mmc: calc 6c63d38f, store 6c63d38f
  979. [ 3.561616@0] meson-mmc: calc 6c63d38f, store 6c63d38f
  980. [ 3.561618@0] meson-mmc: total valid 2
  981. [ 3.561892@0] meson-mmc: amlmmc_dtb_init: register dtb chardev OK
  982. [ 3.561892@0] meson-mmc: Exit aml_emmc_partition_ops OK.
  983. [ 3.566443@0] BLASTER Driver Init
  984. [ 3.566944@0] irblaster: probe
  985. [ 3.567857@0] dmc_monitor_probe
  986. [ 3.568831@2] aml_atvdemod_init: OK, atv demod version: V2.04.
  987. [ 3.569001@2] defendkey ff630218.defendkey: Reserved memory is not enough!
  988. [ 3.569014@2] defendkey: probe of ff630218.defendkey failed with error -22
  989. [ 3.570794@2] usbcore: registered new interface driver snd-usb-audio
  990. [ 3.571874@2] aml_codec_T9015 ff632000.t9015: aml_T9015_audio_codec_probe
  991. [ 3.571896@2] T9015 acodec used by auge, tdmout:1
  992. [ 3.573978@2] asoc debug: aml_audio_controller_probe-127
  993. [ 3.575623@2] asoc-aml-card auge_sound: aml_card_probe, parse error -517
  994. [ 3.575626@2] aml_card_probe error ret:-517
  995. [ 3.576048@2] aml_tdm_platform_probe, tdm ID = 0, lane_cnt = 2
  996. [ 3.576069@2] snd_tdm ff660000.audiobus:tdm@0: lane_mask_out = 0, lane_oe_mask_out = 0
  997. [ 3.576198@2] aml_tdm_platform_probe(), share en = 1
  998. [ 3.576199@2] No channel mask node Channel_Mask
  999. [ 3.576429@2] aml_tdm_platform_probe, tdm ID = 1, lane_cnt = 8
  1000. [ 3.576490@2] TDM id 1 samesource_sel:3
  1001. [ 3.576499@2] snd_tdm ff660000.audiobus:tdm@1: lane_mask_out = 1, lane_oe_mask_out = 0
  1002. [ 3.576709@2] TDM id 1 output clk enable:1
  1003. [ 3.576736@2] aml_tdm_platform_probe(), share en = 1
  1004. [ 3.576737@2] No channel mask node Channel_Mask
  1005. [ 3.576744@2] TDM id 1 tuning clk enable:1
  1006. [ 3.576898@2] aml_tdm_platform_probe, tdm ID = 2, lane_cnt = 4
  1007. [ 3.576916@2] snd_tdm ff660000.audiobus:tdm@2: lane_mask_out = 0, lane_oe_mask_out = 0
  1008. [ 3.577069@2] aml_tdm_platform_probe(), share en = 1
  1009. [ 3.577069@2] No channel mask node Channel_Mask
  1010. [ 3.578168@2] Spdif id 0 tuning clk enable:1
  1011. [ 3.578188@2] hdmitx: audio: aout notify format CT_PCM
  1012. [ 3.578204@2] aml_spdif_platform_probe, register soc platform
  1013. [ 3.578361@2] aml_spdif_platform_probe, register soc platform
  1014. [ 3.578988@2] meson-g12a-pinctrl pinctrl@ff634480: pin GPIOZ_2 already requested by ff3f0000.ethernet; cannot claim for ff660000.audiobus:pdm
  1015. [ 3.578993@2] meson-g12a-pinctrl pinctrl@ff634480: pin-3 (ff660000.audiobus:pdm) status -22
  1016. [ 3.578998@2] meson-g12a-pinctrl pinctrl@ff634480: could not request pin 3 (GPIOZ_2) from group pdm_din0_z on device pinctrl-meson
  1017. [ 3.579002@2] snd_pdm ff660000.audiobus:pdm: Error applying setting, reverse things back
  1018. [ 3.579007@2] snd_pdm ff660000.audiobus:pdm: Can't get pdm pinmux
  1019. [ 3.579396@2] audio_ddr_mngr: 0, irqs toddr 33, frddr 37
  1020. [ 3.579399@2] audio_ddr_mngr: 1, irqs toddr 34, frddr 38
  1021. [ 3.579402@2] audio_ddr_mngr: 2, irqs toddr 35, frddr 39
  1022. [ 3.579405@2] audio_ddr_mngr: 3, irqs toddr 36, frddr 40
  1023. [ 3.579785@2] datain_src:4, datain_chnum:2, datain_chumask:3
  1024. [ 3.579787@2] datalb_src:1, datalb_chnum:2, datalb_chmask:3
  1025. [ 3.579789@2] datain_lane_mask:0x1, datalb_lane_mask:0x1
  1026. [ 3.580075@2] loopback_platform_probe, p_loopback->id:0 register soc platform
  1027. [ 3.580714@2] effect_platform_probe, line:565
  1028. [ 3.580834@2] eqdrc_clk_set, src pll:399999993, clk:199999997
  1029. [ 3.580840@2] effect_platform_probe module:1, lane_mask:1, ch_mask:3
  1030. [ 3.581585@2] vad_platform_probe vad data source sel:4, level:1
  1031. [ 3.581772@2] input: vad_keypad as /devices/platform/soc/ff660000.audiobus/ff660000.audiobus:vad/input/input2
  1032. [ 3.582223@0] Register vad
  1033. [ 3.582651@0] EARC ff660000.audiobus:earc: Check whether support eARC TX
  1034. [ 3.582655@0] EARC ff660000.audiobus:earc: Check whether support eARC TX
  1035. [ 3.582659@0] EARC ff660000.audiobus:earc: Check whether support eARC TX
  1036. [ 3.582662@0] EARC ff660000.audiobus:earc: Check whether support eARC TX
  1037. [ 3.582690@0] EARC ff660000.audiobus:earc: platform get irq tx_cmdc failed, Check whether support eARC TX
  1038. [ 3.582694@0] EARC ff660000.audiobus:earc: platform get irq tx_dmac failed, Check whether support eARC TX
  1039. [ 3.582705@0] earc_platform_probe, register soc platform
  1040. [ 3.582935@0] GACT probability NOT on
  1041. [ 3.582947@0] Mirror/redirect action on
  1042. [ 3.582954@0] u32 classifier
  1043. [ 3.582954@0] Actions configured
  1044. [ 3.582959@0] Netfilter messages via NETLINK v0.30.
  1045. [ 3.583181@0] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
  1046. [ 3.583420@0] ctnetlink v0.93: registering with nfnetlink.
  1047. [ 3.583988@2] xt_time: kernel timezone is -0000
  1048. [ 3.584066@2] ipip: IPv4 and MPLS over IPv4 tunneling driver
  1049. [ 3.584501@2] IPv4 over IPsec tunneling driver
  1050. [ 3.597507@2] ip_tables: (C) 2000-2006 Netfilter Core Team
  1051. [ 3.597695@2] arp_tables: arp_tables: (C) 2002 David S. Miller
  1052. [ 3.605026@2] Initializing XFRM netlink socket
  1053. [ 3.605463@2] NET: Registered protocol family 10
  1054. [ 3.606628@3] mip6: Mobile IPv6
  1055. [ 3.606647@3] ip6_tables: (C) 2000-2006 Netfilter Core Team
  1056. [ 3.617992@3] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
  1057. [ 3.618867@3] NET: Registered protocol family 17
  1058. [ 3.618887@3] NET: Registered protocol family 15
  1059. [ 3.618912@3] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
  1060. [ 3.619013@0] Bluetooth: RFCOMM TTY layer initialized
  1061. [ 3.619029@0] Bluetooth: RFCOMM socket layer initialized
  1062. [ 3.619049@0] Bluetooth: RFCOMM ver 1.11
  1063. [ 3.619059@0] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  1064. [ 3.619062@0] Bluetooth: BNEP filters: protocol multicast
  1065. [ 3.619068@0] Bluetooth: BNEP socket layer initialized
  1066. [ 3.619070@0] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  1067. [ 3.619076@0] Bluetooth: HIDP socket layer initialized
  1068. [ 3.619099@0] l2tp_core: L2TP core driver, V2.0
  1069. [ 3.619107@0] l2tp_ppp: PPPoL2TP kernel driver, V2.0
  1070. [ 3.619109@0] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
  1071. [ 3.619126@0] l2tp_netlink: L2TP netlink interface
  1072. [ 3.619152@0] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
  1073. [ 3.619169@0] l2tp_debugfs: L2TP debugfs support
  1074. [ 3.619171@0] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
  1075. [ 3.619206@0] NET: Registered protocol family 35
  1076. [ 3.619256@0] Key type dns_resolver registered
  1077. [ 3.620969@0] Registering SWP/SWPB emulation handler
  1078. [ 3.621573@0] registered taskstats version 1
  1079. [ 3.838564@0] asoc-aml-card auge_sound: control 2:0:0:I2SIn CLK:0 is already present
  1080. [ 3.838569@0] snd_tdm ff660000.audiobus:tdm@1: ASoC: Failed to add I2SIn CLK: -16
  1081. [ 3.838571@0] aml_dai_tdm_probe, failed add snd tdm controls
  1082. [ 3.838579@0] asoc-aml-card auge_sound: control 2:0:0:I2SIn CLK:0 is already present
  1083. [ 3.838582@0] snd_tdm ff660000.audiobus:tdm@2: ASoC: Failed to add I2SIn CLK: -16
  1084. [ 3.838583@0] aml_dai_tdm_probe, failed add snd tdm controls
  1085. [ 3.838587@0] aml_dai_spdif_probe
  1086. [ 3.838603@0] aml_dai_spdif_probe
  1087. [ 3.838607@0] asoc debug: earc_dai_probe-342
  1088. [ 3.838639@0] master_mode(1), binv(1), finv(0) out_skew(2), in_skew(3)
  1089. [ 3.839586@0] asoc-aml-card auge_sound: multicodec <-> TDM-A mapping ok
  1090. [ 3.839609@0] master_mode(1), binv(1), finv(1) out_skew(2), in_skew(3)
  1091. [ 3.840097@0] asoc-aml-card auge_sound: multicodec <-> TDM-B mapping ok
  1092. [ 3.840118@0] master_mode(1), binv(1), finv(1) out_skew(2), in_skew(3)
  1093. [ 3.840618@0] asoc-aml-card auge_sound: dummy <-> TDM-C mapping ok
  1094. [ 3.841121@0] asoc-aml-card auge_sound: dummy <-> SPDIF mapping ok
  1095. [ 3.841511@0] asoc-aml-card auge_sound: dummy <-> SPDIF-B mapping ok
  1096. [ 3.841515@0] asoc earc_dai_set_fmt, 0x4000, ecc5a690
  1097. [ 3.841980@0] asoc-aml-card auge_sound: dummy <-> ff660000.audiobus:earc mapping ok
  1098. [ 3.841985@0]
  1099. [ 3.841985@0] loopback_dai_set_sysclk, 0, 12288000, 0
  1100. [ 3.841987@0] asoc loopback_dai_set_fmt, 0x4010, eda57e90
  1101. [ 3.842428@0] asoc-aml-card auge_sound: dummy <-> ff660000.audiobus:loopback@0 mapping ok
  1102. [ 3.845358@0] snd_card_add_kcontrols card:ecce8c10
  1103. [ 3.845422@0] eq/drc v1 function enable
  1104. [ 3.845429@0] no node audio_effect for eq/drc info!
  1105. [ 3.845430@0] Failed to add audio effects v1 controls
  1106. [ 3.846068@2] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host
  1107. [ 3.848823@2] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  1108. [ 3.848851@2] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
  1109. [ 3.849199@2] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x20010010
  1110. [ 3.849249@2] xhci-hcd xhci-hcd.0.auto: irq 29, io mem 0xff500000
  1111. [ 3.849966@3] hub 1-0:1.0: USB hub found
  1112. [ 3.849994@3] hub 1-0:1.0: 2 ports detected
  1113. [ 3.850399@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  1114. [ 3.850410@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
  1115. [ 3.850478@3] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
  1116. [ 3.851035@0] hub 2-0:1.0: USB hub found
  1117. [ 3.851059@0] hub 2-0:1.0: 1 port detected
  1118. [ 3.851823@0] aml_vrtc rtc: setting system clock to 2015-01-01 00:00:08 UTC (1420070408)
  1119. [ 3.852234@0] dwc_otg: usb0: type: 1 speed: 0, config: 0, dma: 0, id: 1, phy: ffe09000, ctrl: 0
  1120. [ 3.852236@0] dwc_otg_driver_probe host only, not probe usb_otg!!!
  1121. [ 3.853895@0] meson_cdev probe
  1122. [ 3.853906@0] thermal: read gpupp failed
  1123. [ 3.854036@0] meson_cdev index: 0
  1124. [ 3.854186@0] thermal: read gpupp failed
  1125. [ 3.854313@0] meson_cdev index: 1
  1126. [ 3.854318@0] cpucore_cooling_register, max_cpu_core_num:4
  1127. [ 3.854529@0] meson_cdev index: 2
  1128. [ 3.854533@0] thermal: read gpupp failed
  1129. [ 3.854576@0] meson_cdev index: 3
  1130. [ 3.854635@0] find tzd id: 0
  1131. [ 3.854748@0] find tzd id: 0
  1132. [ 3.854778@0] meson_cdev probe done
  1133. [ 3.854909@0] gxbb_pm: enter meson_pm_probe!
  1134. [ 3.854938@0] gxbb_pm: meson_pm_probe done
  1135. [ 3.855327@0 5.358565@2] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
  1136. [ 5.466846@2] prepare_namespace() wait 79
  1137. [ 5.466920@2] md: Waiting for all devices to be available before autodetect
  1138. [ 5.472173@2] md: If you don't use raid, use raid=noautodetect
  1139. [ 5.478777@2] md: Autodetecting RAID arrays.
  1140. [ 5.482208@2] md: Scanned 0 and added 0 devices.
  1141. [ 5.486824@2] md: autorun ...
  1142. [ 5.489742@2] md: ... autorun DONE.
  1143. [ 5.494123@2] EXT4-fs (mmcblk0p18): couldn't mount as ext3 due to feature incompatibilities
  1144. [ 5.501932@2] EXT4-fs (mmcblk0p18): couldn't mount as ext2 due to feature incompatibilities
  1145. [ 5.515081@2] EXT4-fs (mmcblk0p18): mounted filesystem without journal. Opts: (null)
  1146. [ 5.517596@2] VFS: Mounted root (ext4 filesystem) readonly on device 179:18.
  1147. [ 5.525471@2] devtmpfs: mounted
  1148. [ 5.528522@2] Freeing unused kernel memory: 1024K
  1149. [ 5.577450@2] init: init first stage started!
  1150. [ 5.578323@2] init: Using Android DT directory /proc/device-tree/firmware/android/
  1151. [ 5.587528@2] init: [libfs_mgr]fs_mgr_read_fstab_default(): failed to find device default fstab
  1152. [ 5.638589@2] EXT4-fs (mmcblk0p17): mounted filesystem without journal. Opts: barrier=1,inode_readahead_blks=8
  1153. [ 5.643120@2] init: [libfs_mgr]__mount(source=/dev/block/odm,target=/odm,type=ext4)=0: Success
  1154. [ 5.654151@2] EXT4-fs (mmcblk0p19): mounted filesystem without journal. Opts: barrier=1,inode_readahead_blks=8
  1155. [ 5.661794@2] init: [libfs_mgr]__mount(source=/dev/block/product,target=/product,type=ext4)=0: Success
  1156. [ 5.681240@2] EXT4-fs (mmcblk0p16): mounted filesystem without journal. Opts: barrier=1,inode_readahead_blks=8
  1157. [ 5.685740@2] init: [libfs_mgr]__mount(source=/dev/block/vendor,target=/vendor,type=ext4)=0: Success
  1158. [ 5.695062@2] init: Skipped setting INIT_AVB_VERSION (not in recovery mode)
  1159. [ 5.702041@2] init: Loading SELinux policy
  1160. [ 5.889642@2] audit: type=1403 audit(1420070410.532:2): policy loaded auid=4294967295 ses=4294967295
  1161. [ 5.893357@2] selinux: SELinux: Loaded policy from /odm/etc/selinux/precompiled_sepolicy
  1162. [ 5.893357@2]
  1163. [ 5.912203@2] selinux: SELinux: Loaded file_contexts
  1164. [ 5.912203@2]
  1165. [ 5.917758@3] init: init second stage started!
  1166. [ 5.943587@3] init: Using Android DT directory /proc/device-tree/firmware/android/
  1167. [ 5.950816@3] selinux: SELinux: Loaded file_contexts
  1168. [ 5.950816@3]
  1169. [ 5.952128@3] init: Running restorecon...
  1170. [ 5.963247@3] audit: type=1400 audit(1420070410.608:3): avc: denied { getattr } for pid=1 comm="init" path="/sbin/su" dev="mmcblk0p18" ino=2693 scontext=u:r:init:s0 tcontext=u:object_r:su_exec:s0 tclass=file permissive=1
  1171. [ 5.985763@3] init: waitid failed: No child processes
  1172. [ 5.990479@3] init: Couldn't load property file '/odm/default.prop': open() failed: No such file or directory: No such file or directory
  1173. [ 6.004395@3] init: Created socket '/dev/socket/property_service', mode 666, user 0, group 0
  1174. [ 6.008086@3] init: Forked subcontext for 'u:r:vendor_init:s0' with pid 2406
  1175. [ 6.014983@3] init: Forked subcontext for 'u:r:vendor_init:s0' with pid 2407
  1176. [ 6.021523@3] init: Parsing file /init.rc...
  1177. [ 6.143538@3] ueventd: ueventd started!
  1178. [ 6.147309@3] selinux: SELinux: Loaded file_contexts
  1179. [ 6.147309@3]
  1180. [ 6.148476@3] ueventd: Parsing file /ueventd.rc...
  1181. [ 6.159215@3] ueventd: Parsing file /vendor/ueventd.rc...
  1182. [ 6.163445@3] ueventd: /vendor/ueventd.rc: 109: /sys/ lines must have 5 entries
  1183. [ 6.166482@3] ueventd: Parsing file /odm/ueventd.rc...
  1184. [ 6.171473@3] ueventd: Unable to read config file '/odm/ueventd.rc': open() failed: No such file or directory
  1185. [ 6.179468@0] mali_kbase: no symbol version for module_layout
  1186. [ 6.179480@0] mali_kbase: loading out-of-tree module taints kernel.
  1187. [ 6.183607@0] mali ffe40000.bifrost: Continuing without Mali regulator control
  1188. [ 6.183703@0] mali ffe40000.bifrost: max pp is 2
  1189. [ 6.183707@0] mali ffe40000.bifrost: set min pp to default 1
  1190. [ 6.183711@0] mali ffe40000.bifrost: min pp is 1
  1191. [ 6.183715@0] mali ffe40000.bifrost: set min clk default to 0
  1192. [ 6.183717@0] mali ffe40000.bifrost: min clk is 0
  1193. [ 6.183735@0] mali ffe40000.bifrost: hiu io source 0xf1785000
  1194. [ 6.183743@0] mali ffe40000.bifrost: hiu io source 0xf1787000
  1195. [ 6.183747@0] mali ffe40000.bifrost: num of pp used most of time 1
  1196. [ 6.183751@0] mali ffe40000.bifrost: clock dvfs cfg table size is 6
  1197. [ 6.183822@0] mali ffe40000.bifrost: max clk set 4
  1198. [ 6.183825@0] mali ffe40000.bifrost: max clk is 4
  1199. [ 6.183829@0] mali ffe40000.bifrost: turbo clk set to 5
  1200. [ 6.183833@0] mali ffe40000.bifrost: turbo clk is 5
  1201. [ 6.183835@0] mali ffe40000.bifrost: default clk set to 4
  1202. [ 6.183838@0] mali ffe40000.bifrost: default clk is 4
  1203. [ 6.183845@0] mali ffe40000.bifrost: ====================0====================
  1204. [ 6.183845@0] clk_freq= 285714285, clk_parent=fclk_div7, voltage=1150, keep_count=5, threshod=<100 190>, clk_sample=285
  1205. [ 6.183849@0] mali ffe40000.bifrost: ====================1====================
  1206. [ 6.183849@0] clk_freq= 400000000, clk_parent=fclk_div5, voltage=1150, keep_count=5, threshod=<152 207>, clk_sample=400
  1207. [ 6.183853@0] mali ffe40000.bifrost: ====================2====================
  1208. [ 6.183853@0] clk_freq= 500000000, clk_parent=fclk_div4, voltage=1150, keep_count=5, threshod=<180 220>, clk_sample=500
  1209. [ 6.183858@0] mali ffe40000.bifrost: ====================3====================
  1210. [ 6.183858@0] clk_freq= 666666666, clk_parent=fclk_div3, voltage=1150, keep_count=5, threshod=<210 236>, clk_sample=666
  1211. [ 6.183865@0] mali ffe40000.bifrost: ====================4====================
  1212. [ 6.183865@0] clk_freq= 846000000, clk_parent= gp0_pll, voltage=1150, keep_count=5, threshod=<230 255>, clk_sample=846
  1213. [ 6.183869@0] mali ffe40000.bifrost: ====================5====================
  1214. [ 6.183869@0] clk_freq= 846000000, clk_parent= gp0_pll, voltage=1150, keep_count=5, threshod=<230 255>, clk_sample=846
  1215. [ 6.183872@0] mali ffe40000.bifrost: clock dvfs table size is 6
  1216. [ 6.184149@0] mali_plat=bf05d2d8
  1217. [ 6.184504@0] find tzd id: 0
  1218. [ 6.184528@0] gpu cooling register okay with err=0
  1219. [ 6.184746@0] find tzd id: 0
  1220. [ 6.184754@0] gpu core cooling register okay with err=0
  1221. [ 6.184780@0] shader_present=1, tiler_present=1, l2_present=1
  1222. [ 6.184861@0] Mali_pwr_on:gpu_irq : 200
  1223. [ 6.185383@2] hrtimer: interrupt took 90734428444296 ns
  1224. [ 6.185976@2] mali ffe40000.bifrost: GPU identified as 0x3 arch 7.0.9 r0p0 status 0
  1225. [ 6.188345@2] mali ffe40000.bifrost: Probed as mali0
  1226. [ 6.194537@2] PPMGRVPP: info: RegisterTB_Function: gfunc (null), func: bf08e024, ver:TB detect: v2016.11.15a *** [ Tue Mar 19 19:21:39 CST 2019]-[ renjiang.han]-[* master]-[67f03d41e0612a58d1edd96db9bc8b92de1a59b1]-[Date: Wed Jul 4 00:44:57 2018 +0800]-[2]
  1227. [ 6.462653@3] ueventd: Parsing file /ueventd.amlogic.rc...
  1228. [ 6.467949@3] ueventd: Unable to read config file '/ueventd.amlogic.rc': open() failed: No such file or directory
  1229. [ 6.929152@3] ueventd: Coldboot took 0.447 seconds
  1230. [ 6.964693@3] audit: type=1400 audit(1420070411.608:4): avc: denied { write } for pid=2406 comm="init" name="watermark_scale_factor" dev="proc" ino=11654 scontext=u:r:vendor_init:s0 tcontext=u:object_r:proc_vm_writable:s0 tclass=file permissive=1
  1231. [ 7.008131@1] EXT4-fs (mmcblk0p20): Ignoring removed nomblk_io_submit option
  1232. [ 7.038020@1] EXT4-fs (mmcblk0p20): recovery complete
  1233. [ 7.038065@1] EXT4-fs (mmcblk0p20): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit
  1234. [ 11.318911@3] e2fsck: e2fsck 1.43.3 (04-Sep-2016)
  1235. [ 11.318911@3]
  1236. [ 11.319668@3] e2fsck: Pass 1: Checking inodes, blocks, and sizes
  1237. [ 11.319668@3]
  1238. [ 11.327320@3] e2fsck: Pass 2: Checking directory structure
  1239. [ 11.327320@3]
  1240. [ 11.334402@3] e2fsck: Pass 3: Checking directory connectivity
  1241. [ 11.334402@3]
  1242. [ 11.341798@3] e2fsck: Pass 4: Checking reference counts
  1243. [ 11.341798@3]
  1244. [ 11.348605@3] e2fsck: Pass 5: Checking group summary information
  1245. [ 11.348605@3]
  1246. [ 11.350267@0] vout: aml_tvout_mode_work: monitor_timeout
  1247. [ 11.361515@3] e2fsck: /dev/block/data: 13035/3570480 files (6.5% non-contiguous), 517895/14254080 blocks
  1248. [ 11.361515@3]
  1249. [ 11.373764@3] init: [libfs_mgr]superblock s_max_mnt_count:65535,/dev/block/data
  1250. [ 11.380661@3] EXT4-fs (mmcblk0p20): Ignoring removed nomblk_io_submit option
  1251. [ 11.396889@3] EXT4-fs (mmcblk0p20): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
  1252. [ 11.402727@3] init: [libfs_mgr]__mount(source=/dev/block/data,target=/data,type=ext4)=0: Success
  1253. [ 11.411487@3] init: [libfs_mgr]/data is file encrypted
  1254. [ 11.417442@3] init: [libfs_mgr]superblock s_max_mnt_count:65535,/dev/block/cache
  1255. [ 11.423860@3] init: [libfs_mgr]Filesystem on /dev/block/cache was not cleanly shutdown; state flags: 0x1, incompat feature flags: 0x246
  1256. [ 11.437084@3] EXT4-fs (mmcblk0p3): Ignoring removed nomblk_io_submit option
  1257. [ 11.445672@3] EXT4-fs (mmcblk0p3): recovery complete
  1258. [ 11.447821@3] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit
  1259. [ 11.458583@3] init: [libfs_mgr]check_fs(): mount(/dev/block/cache,/cache,ext4)=0: Success
  1260. [ 11.487965@3] init: [libfs_mgr]check_fs(): unmount(/cache) succeeded
  1261. [ 11.488712@3] init: [libfs_mgr]Running /system/bin/e2fsck on /dev/block/cache
  1262. [ 11.566407@1] e2fsck: e2fsck 1.43.3 (04-Sep-2016)
  1263. [ 11.566407@1]
  1264. [ 11.567173@1] e2fsck: Pass 1: Checking inodes, blocks, and sizes
  1265. [ 11.567173@1]
  1266. [ 11.574814@1] e2fsck: Pass 2: Checking directory structure
  1267. [ 11.574814@1]
  1268. [ 11.583155@1] EXT4-fs (mmcblk0p3): Ignoring removed nomblk_io_submit option
  1269. [ 11.591410@1] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
  1270. [ 11.600183@1] init: [libfs_mgr]__mount(source=/dev/block/cache,target=/cache,type=ext4)=0: Success
  1271. [ 11.610016@1] init: [libfs_mgr]superblock s_max_mnt_count:65535,/dev/block/metadata
  1272. [ 11.617483@1] EXT4-fs (mmcblk0p13): Ignoring removed nomblk_io_submit option
  1273. [ 11.625949@1] EXT4-fs (mmcblk0p13): recovery complete
  1274. [ 11.628607@1] EXT4-fs (mmcblk0p13): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit
  1275. [ 11.701276@1] EXT4-fs (mmcblk0p13): Ignoring removed nomblk_io_submit option
  1276. [ 11.704859@1] EXT4-fs (mmcblk0p13): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
  1277. [ 11.769683@3] EXT4-fs (mmcblk0p10): Ignoring removed nomblk_io_submit option
  1278. [ 11.774005@3] EXT4-fs (mmcblk0p10): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
  1279. [ 11.834502@1] EXT4-fs (mmcblk0p15): Ignoring removed nomblk_io_submit option
  1280. [ 11.838107@1] EXT4-fs (mmcblk0p15): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
  1281. [ 11.847935@1] init: 31 output lines suppressed due to ratelimiting
  1282. [ 11.875228@1] register clk_set_setting cpu[43]
  1283. [ 11.889853@2] Registered firmware driver success.
  1284. [ 11.891456@2] Try to load video/h264_enc.bin ...
  1285. [ 11.896822@2] load firmware size : 76288, Name : video/h264_enc.bin.
  1286. [ 11.900012@2] the fw pack ver v0.0 is too lower.
  1287. [ 11.904547@2] it may work abnormally so need to be update in time.
  1288. [ 11.911431@2] Try to load video/video_ucode.bin ...
  1289. [ 11.958058@2] load firmware size : 1706240, Name : video/video_ucode.bin.
  1290. [ 11.959431@2] the fw pack ver v0.2 is too lower.
  1291. [ 11.963812@2] it may work abnormally so need to be update in time.
  1292. [ 12.079254@3] Amlogic A/V streaming port init
  1293. [ 12.089589@3] get gate demux control ok ec9a0540
  1294. [ 12.089631@3] get gate parser_top control ok ec9a05c0
  1295. [ 12.098411@2] get gate vdec control ok ecf4f240
  1296. [ 12.098470@2] get gate clk_81 control ok ecf4f1c0
  1297. [ 12.102887@2] get gate clk_vdec_mux control ok ecf4f640
  1298. [ 12.108288@2] get gate clk_hcodec_mux control ok ecf4f3c0
  1299. [ 12.113421@2] get gate clk_hevc_mux control ok ecf4fbc0
  1300. [ 12.118632@2] get gate clk_hevcb_mux control ok ecf4f440
  1301. [ 12.123892@2] get gate ahbarb0 control ok ecf4f0c0
  1302. [ 12.128650@2] get gate asyncfifo control failed (null)
  1303. [ 12.182313@2] ammvdec_h264 module init
  1304. [ 12.253572@3] ammvdec_mpeg12 module init
  1305. [ 12.272976@3] ammvdec_mpeg4_driver_init_module
  1306. [ 12.341060@3] amvenc_avc_probe -- reserved memory config fail.
  1307. [ 12.341258@3] amvenc_avc - cma memory pool size: 60 MB
  1308. [ 12.346490@3] encode_wq_init.
  1309. [ 12.349318@3] encode start monitor.
  1310. [ 12.352898@2] encode workqueue monitor start.
  1311. [ 12.366156@3] vpu_init
  1312. [ 12.366505@3] vpu_probe
  1313. [ 12.366524@3] HevcEnc reserved memory config fail.
  1314. [ 12.370071@3] HevcEnc - cma memory pool size: 64 MB
  1315. [ 12.375007@3] HevcEnc - wave420l_irq: 59
  1316. [ 12.378906@3] vpu base address get from platform driver physical base addr=0xff610000, virtual base=0xf25c0000
  1317. [ 12.390486@3] success to probe vpu device with video memory from cma
  1318. [ 12.521395@3] logd.auditd: start
  1319. [ 12.521456@3] logd.klogd: 12463198463
  1320. [ 15.162533@2] type=1400 audit(1420070419.804:5): avc: denied { setattr } for pid=2406 comm="init" name="droidota" dev="mmcblk0p20" ino=2101250 scontext=u:r:vendor_init:s0 tcontext=u:object_r:update_data_file:s0 tclass=dir permissive=1
  1321. [ 15.177901@2] type=1400 audit(1420070419.804:5): avc: denied { setattr } for pid=2406 comm="init" name="droidota" dev="mmcblk0p20" ino=2101250 scontext=u:r:vendor_init:s0 tcontext=u:object_r:update_data_file:s0 tclass=dir permissive=1
  1322. [ 15.198606@2] type=1400 audit(1420070419.808:6): avc: denied { setattr } for pid=2406 comm="init" name="log" dev="mmcblk0p20" ino=2495234 scontext=u:r:vendor_init:s0 tcontext=u:object_r:log_file:s0 tclass=dir permissive=1
  1323. [ 15.248027@0] ATBM: register atbm8881 demod driver
  1324. [ 15.272807@0] aml dvb init
  1325. [ 15.407595@0] nn is disable,should not do probe continue
  1326. [ 15.453514@2] logd.daemon: reinit
  1327. [ 17.709561@2] init: Could not start service 'tee_preload_fw' as part of class 'core': Cannot find '/vendor/bin/tee_preload_fw': No such file or directory
  1328. [ 17.737881@0] init: setpgid failed for console: Operation not permitted
  1329. [ 17.742922@2] healthd: BatteryTemperaturePath not found
  1330. [ 17.746604@2] healthd: BatteryCycleCountPath not found
  1331. [ 17.758904@0] init: Failed to bind socket 'pdx/system/vr/display/client': No such file or directory
  1332. [ 17.759502@0] init: Failed to bind socket 'pdx/system/vr/display/manager': No such file or directory
  1333. [ 17.759989@0] init: Failed to bind socket 'pdx/system/vr/display/vsync': No such file or directory
  1334. [ 17.771425@1] init: Could not find service hosting interface vendor.amlogic.hardware.systemcontrol@1.1::ISystemControl/default
  1335. [ 17.796704@0] android.hardware.health@2.0-impl: wakealarm_init: timerfd_create failed
  1336. [ 17.797391@2] type=1400 audit(1420070419.808:6): avc: denied { setattr } for pid=2406 comm="init" name="log" dev="mmcblk0p20" ino=2495234 scontext=u:r:vendor_init:s0 tcontext=u:object_r:log_file:s0 tclass=dir permissive=1
  1337. [ 17.797423@2] type=1400 audit(1420070422.440:7): avc: denied { add_name } for pid=2406 comm="init" name="def_vstreambuf_sizeM" scontext=u:r:vendor_init:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=1
  1338. [ 17.797537@2] type=1400 audit(1420070422.440:7): avc: denied { add_name } for pid=2406 comm="init" name="def_vstreambuf_sizeM" scontext=u:r:vendor_init:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=1
  1339. [ 17.797554@2] type=1400 audit(1420070422.440:8): avc: denied { create } for pid=2406 comm="init" name="def_vstreambuf_sizeM" scontext=u:r:vendor_init:s0 tcontext=u:object_r:sysfs:s0 tclass=file permissive=1
  1340. [ 17.811500@3] unifykey: amlkey_init_gen() enter!
  1341. [ 17.882020@0] healthd: battery l=42 v=4 t=42.4 h=2 st=2 c=1 fc=10000000 chg=u
  1342. [ 17.948229@3] hdmitx: system: set hdcp_pwr 1
  1343. console:/ # [ 17.995460@3] emmc_key_read:114, read ok
  1344. [ 17.995498@3] unifykey: amlkey_init_gen() storagekey_info.buffer=c5080000, storagekey_info.size = 40000!
  1345. [ 18.004417@3] init: Could not find service hosting interface vendor.amlogic.hardware.systemcontrol@1.1::ISystemControl/default
  1346. [ 18.019246@1] vfm_map_store:rm default
  1347. [ 18.019603@2] vfm_map_store:add default decoder ppmgr deinterlace amvideo
  1348. [ 18.031476@2] file system registered
  1349. [ 18.034891@0] assign_ffs_buffer FFS_BUFFER_MAX=100!!!
  1350. [ 18.036108@3] hdmitx: system: restore hdcp_pwr 0
  1351. [ 20.608033@0] init: Could not find service hosting interface vendor.amlogic.hardware.systemcontrol@1.1::ISystemControl/default
  1352. [ 20.614760@0] init: Could not find service hosting interface vendor.amlogic.hardware.systemcontrol@1.1::ISystemControl/default
  1353. [ 20.626293@0] init: Could not find service hosting interface vendor.amlogic.hardware.systemcontrol@1.1::ISystemControl/default
  1354. [ 20.843563@1] type=1400 audit(1420070422.440:8): avc: denied { create } for pid=2406 comm="init" name="def_vstreambuf_sizeM" scontext=u:r:vendor_init:s0 tcontext=u:object_r:sysfs:s0 tclass=file permissive=1
  1355. [ 20.856342@1] type=1400 audit(1420070425.488:9): avc: denied { getattr } for pid=1 comm="init" path="/sbin/su" dev="mmcblk0p18" ino=2693 scontext=u:r:init:s0 tcontext=u:object_r:su_exec:s0 tclass=file permissive=1
  1356. [ 20.875395@1] type=1400 audit(1420070425.488:9): avc: denied { getattr } for pid=1 comm="init" path="/sbin/su" dev="mmcblk0p18" ino=2693 scontext=u:r:init:s0 tcontext=u:object_r:su_exec:s0 tclass=file permissive=1
  1357. [ 20.894152@1] type=1400 audit(1420070425.492:10): avc: denied { execute } for pid=3207 comm="init" name="su" dev="mmcblk0p18" ino=2693 scontext=u:r:init:s0 tcontext=u:object_r:su_exec:s0 tclass=file permissive=1
  1358. [ 20.913376@1] type=1400 audit(1420070425.492:10): avc: denied { execute } for pid=3207 comm="init" name="su" dev="mmcblk0p18" ino=2693 scontext=u:r:init:s0 tcontext=u:object_r:su_exec:s0 tclass=file permissive=1
  1359. [ 20.931806@1] type=1400 audit(1420070425.492:11): avc: denied { read open } for pid=3207 comm="init" path="/sbin/su" dev="mmcblk0p18" ino=2693 scontext=u:r:init:s0 tcontext=u:object_r:su_exec:s0 tclass=file permissive=1
  1360. [ 20.933226@0] vout: vout_io_open
  1361. [ 20.969865@1] fb: osd_open, 1497, fb_index=0,fb_rmem_size=26738688
  1362. [ 20.970641@1] fb: osd_open, 1497, fb_index=1,fb_rmem_size=1048576
  1363. [ 20.976696@1] fb: osd_open, 1497, fb_index=2,fb_rmem_size=1048576
  1364. [ 20.982828@1] fb: vpu clkc clock is 199 MHZ
  1365. [ 20.986767@1] vpu: switch_vpu_mem_pd: unsupport vpu mod: 18
  1366. [ 20.992306@1] vpu: switch_vpu_mem_pd: unsupport vpu mod: 22
  1367. [ 20.997890@1] vpu: switch_vpu_mem_pd: unsupport vpu mod: 53
  1368. [ 21.003436@1] fb: osd_open, 1497, fb_index=3,fb_rmem_size=8388608
  1369. [ 21.341497@0] read descriptors
  1370. [ 21.341539@0] read strings
  1371. [ 21.527952@3] audit: audit_lost=1 audit_rate_limit=5 audit_backlog_limit=64
  1372. [ 21.529308@3] audit: rate limit exceeded
  1373. [ 22.766664@0] init: Could not find service hosting interface vendor.amlogic.hardware.hdmicec@1.0::IDroidHdmiCEC/default
  1374. [ 22.823904@0] init: Could not find service hosting interface vendor.amlogic.hardware.systemcontrol@1.1::ISystemControl/default
  1375. [ 22.850076@0] init: Could not find service hosting interface vendor.amlogic.hardware.systemcontrol@1.0::ISystemControl/default
  1376. [ 22.993292@0] init: Could not find service hosting interface vendor.amlogic.hardware.hdmicec@1.0::IDroidHdmiCEC/default
  1377. [ 23.030565@0] init: Could not find service hosting interface vendor.amlogic.hardware.systemcontrol@1.1::ISystemControl/default
  1378. [ 23.053558@0] init: Could not find service hosting interface vendor.amlogic.hardware.systemcontrol@1.0::ISystemControl/default
  1379. [ 23.219138@0] init: Could not find service hosting interface vendor.amlogic.hardware.hdmicec@1.0::IDroidHdmiCEC/default
  1380. [ 23.237268@0] init: Could not find service hosting interface vendor.amlogic.hardware.systemcontrol@1.1::ISystemControl/default
  1381. [ 23.256937@0] init: Could not find service hosting interface vendor.amlogic.hardware.systemcontrol@1.0::ISystemControl/default
  1382. [ 23.419311@0] init: Could not find service hosting interface vendor.amlogic.hardware.hdmicec@1.0::IDroidHdmiCEC/default
  1383. [ 23.489106@1] [DI] load 0x3e00 pq table len 424 later.
  1384. [ 24.116035@2] [DI] load 0x3e00 pq table len 424 later.
  1385. [ 24.116107@2] [DI] remove 0x3e00 table.
  1386. [ 24.144289@3] type=1400 audit(1420070426.172:13): avc: denied { read } for pid=3146 comm="android.hardwar" name="u:object_r:default_prop:s0" dev="tmpfs" ino=11515 scontext=u:r:hal_neuralnetworks_default:s0 tcontext=u:object_r:default_prop:s0 tclass=file permissive=1
  1387. [ 24.162570@3] type=1400 audit(1420070428.788:16): avc: denied { open } for pid=3125 comm="systemcontrol" path="/dev/__properties__/u:object_r:system_prop:s0" dev="tmpfs" ino=11574 scontext=u:r:system_control:s0 tcontext=u:object_r:system_prop:s0 tclass=file permissive=1
  1388. [ 24.276916@1] vout: vout_io_open
  1389. [ 24.276953@1] vout: vout_ioctl: cmd_dir = 0x2, cmd_nr = 0x0
  1390. [ 24.280159@1] vout: vout_io_release
  1391. [ 24.348205@3] avc open
  1392. [ 24.348235@3] amvenc_avc check CMA pool success, max instance: 3.
  1393. [ 24.352621@3] allocating phys 0x64400000, size 20480k, wq:eca8a400.
  1394. [ 24.357523@3] amvenc_avc memory config success, buff start:0x64400000, size is 0x1400000, wq:eca8a400.
  1395. [ 24.366977@3] avc release, wq:eca8a400
  1396. [ 24.370524@3] remove encode_work_queue eca8a400 success, _destroy_encode_work_queue line 3513.
  1397. [ 24.379574@3] [+] vpu_open
  1398. [ 24.384431@3] allocating phys 0x64400000, virt addr 0x0, size 65536k
  1399. [ 24.388423@3] [-] vpu_open, ret: 0
  1400. [ 24.391645@3] vpu_release
  1401. [ 24.394206@3] vpu_free_buffers
  1402. [ 24.397158@3] vpu_free_instances
  1403. [ 24.400438@3] vpu_release, s_video_memory 0x64400000
  1404. [ 26.594460@3] cectx ff80023c.aocec: init_cec_port_info phy_addr:0, port num:1
  1405. [ 26.596088@3] cectx ff80023c.aocec: port_seq=0x0
  1406. [ 26.600865@3] cectx ff80023c.aocec: portinfo id:0 arc:0 phy:1000,type:0
  1407. [ 26.632744@0] healthd: battery l=42 v=4 t=42.4 h=2 st=2 c=1 fc=10000000 chg=u
  1408. [ 27.507963@0] aml_spdif_open
  1409. [ 27.508756@0] aml_spdif_close
  1410. [ 27.509429@0] aml_tdm_open
  1411. [ 27.513435@0] asoc debug: earc_open-138
  1412. [ 27.515670@3] asoc debug: earc_close-209
  1413. [ 27.519291@3] aml_tdm_open
  1414. [ 27.522790@3] loopback_dai_startup
  1415. [ 27.525310@2] loopback_dai_shutdown
  1416. [ 27.529046@2] aml_tdm_open
  1417. [ 35.431484@3] fb: osd[0] enable: 1 scale:0x10001 (HwBinder:3138_2)
  1418. [ 35.432024@3] fb: osd[0] enable: 1 scale:0x10001 (HwBinder:3138_2)
  1419. [ 35.452110@3] fb: free_scale_switch to fb0, mode: 0x10001
  1420. [ 35.452206@3] fb: set logo loaded
  1421. [ 37.449141@1] capability: warning: `main' uses 32-bit capabilities (legacy support in use)
  1422. [ 39.613514@1] early_suspend_state=0
  1423. [ 46.064598@1] healthd: battery l=42 v=4 t=42.4 h=2 st=2 c=1 fc=10000000 chg=u
  1424. [ 46.067875@1] healthd: battery l=42 v=4 t=42.4 h=2 st=2 c=1 fc=10000000 chg=u
  1425. [ 48.664266@3] type=1400 audit(1420070428.788:16): avc: denied { open } for pid=3125 comm="systemcontrol" path="/dev/__properties__/u:object_r:system_prop:s0" dev="tmpfs" ino=11574 scontext=u:r:system_control:s0 tcontext=u:object_r:system_prop:s0 tclass=file permissive=1
  1426. [ 48.683218@3] type=1400 audit(1420070453.308:17): avc: denied { read } for pid=3414 comm="android.ui" name="state" dev="sysfs" ino=9508 scontext=u:r:system_server:s0 tcontext=u:object_r:sysfs_amhdmitx:s0 tclass=file permissive=1
  1427. [ 48.703093@3] type=1400 audit(1420070453.308:17): avc: denied { read } for pid=3414 comm="android.ui" name="state" dev="sysfs" ino=9508 scontext=u:r:system_server:s0 tcontext=u:object_r:sysfs_amhdmitx:s0 tclass=file permissive=1
  1428. [ 48.723115@3] type=1400 audit(1420070453.308:18): avc: denied { open } for pid=3414 comm="android.ui" path="/sys/devices/virtual/amhdmitx/amhdmitx0/hdmi/state" dev="sysfs" ino=9508 scontext=u:r:system_server:s0 tcontext=u:object_r:sysfs_amhdmitx:s0 tclass=file permissive=1
  1429. [ 48.747351@3] type=1400 audit(1420070453.308:18): avc: denied { open } for pid=3414 comm="android.ui" path="/sys/devices/virtual/amhdmitx/amhdmitx0/hdmi/state" dev="sysfs" ino=9508 scontext=u:r:system_server:s0 tcontext=u:object_r:sysfs_amhdmitx:s0 tclass=file permissive=1
  1430. [ 48.771282@3] type=1400 audit(1420070453.308:19): avc: denied { getattr } for pid=3414 comm="android.ui" path="/sys/devices/virtual/amhdmitx/amhdmitx0/hdmi/state" dev="sysfs" ino=9508 scontext=u:r:system_server:s0 tcontext=u:object_r:sysfs_amhdmitx:s0 tclass=file permissive=1
  1431. [ 51.710363@3] cectx ff80023c.aocec: init_cec_port_info phy_addr:0, port num:1
  1432. [ 51.711922@3] cectx ff80023c.aocec: port_seq=0x0
  1433. [ 51.716599@3] cectx ff80023c.aocec: portinfo id:0 arc:0 phy:1000,type:0
  1434. [ 52.031427@1] eth0: device MAC address 00:df:12:00:a3:31
  1435. [ 52.115658@0] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP.
  1436. [ 52.118637@0] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  1437. [ 52.437434@0] sdcardfs version 2.0
  1438. [ 52.437542@0] sdcardfs: dev_name -> /data/media
  1439. [ 52.440005@0] sdcardfs: options -> fsuid=1023,fsgid=1023,multiuser,derive_gid,default_normal,mask=0,userid=0,gid=1015
  1440. [ 52.450800@0] sdcardfs: mnt -> eca87910
  1441. [ 52.455121@3] sdcardfs: mounted on top of /data/media type ext4
  1442. [ 52.461205@3] Remount options were mask=0,gid=9997 for vfsmnt eb30e310.
  1443. [ 52.466714@3] sdcardfs : options - debug:1
  1444. [ 52.470787@3] sdcardfs : options - gid:9997
  1445. [ 52.474943@3] sdcardfs : options - mask:0
  1446. [ 52.479546@3] Remount options were mask=0,gid=9997 for vfsmnt ebfa9b10.
  1447. [ 52.485605@3] sdcardfs : options - debug:1
  1448. [ 52.489564@3] sdcardfs : options - gid:9997
  1449. [ 52.493733@3] sdcardfs : options - mask:0
  1450. [ 55.175281@3] aml_wifi wifi: [usb_power_control] Set WiFi power down
  1451. [ 55.389617@3] aml_wifi wifi: [usb_power_control] Set WiFi power on !
  1452. [ 55.391717@0] meson-mmc: sdio: resp_timeout,vstat:0xa1ff2800,virqc:3fff
  1453. [ 55.396921@0] meson-mmc: sdio: err: wait for irq service, bus_fsm:0x8
  1454. [ 55.404386@0] meson-mmc: sdio: resp_timeout,vstat:0xa1ff2800,virqc:3fff
  1455. [ 55.409923@0] meson-mmc: sdio: err: wait for irq service, bus_fsm:0x8
  1456. [ 55.420939@0] meson-mmc: sdio: resp_timeout,vstat:0xa1ff2800,virqc:3fff
  1457. [ 55.422920@0] meson-mmc: sdio: err: wait for irq service, bus_fsm:0x8
  1458. [ 55.432012@3] meson-mmc: actual_clock :0, HHI_nand: 0x80
  1459. [ 55.434644@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c
  1460. [ 55.458320@3] meson-mmc: actual_clock :400000, HHI_nand: 0x80
  1461. [ 55.458427@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c
  1462. [ 55.483650@3] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
  1463. [ 55.488561@3] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
  1464. [ 55.492040@3] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
  1465. [ 55.595159@3] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0
  1466. [ 55.599282@3] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
  1467. [ 55.605276@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
  1468. [ 55.612287@3] meson-mmc: Data 1 aligned delay is 0
  1469. [ 55.617045@3] meson-mmc: sdio: clk 199999997 tuning start
  1470. [ 55.623587@3] meson-mmc: sdio: rx_tuning_result[0] = 40
  1471. [ 55.628828@3] meson-mmc: sdio: rx_tuning_result[1] = 40
  1472. [ 55.633939@3] meson-mmc: sdio: rx_tuning_result[2] = 40
  1473. [ 55.638044@3] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffb6
  1474. [ 55.646335@3] meson-mmc: sdio: rx_tuning_result[4] = 40
  1475. [ 55.650403@3] meson-mmc: sdio: best_win_start =4, best_win_size =4
  1476. [ 55.656565@3] meson-mmc: sdio: sd_emmc_regs->gclock=0x10000245,sd_emmc_regs->gadjust=0x12000
  1477. [ 55.669579@3] sdio: new ultra high speed SDR104 SDIO card at address 0001
  1478. [ 55.671721@3] sdio: clock 199999997, 4-bit-bus-width
  1479. [ 55.677656@1] meson-mmc: [sdio_reinit] finish
  1480. [ 55.681255@1] aml_wifi wifi: [usb_power_control] Set WiFi power on !
  1481. [ 55.890335@1] aml_wifi wifi: [pci_reinit] pci wifi reinit!
  1482. [ 55.890375@1] aml_wifi wifi: [wifi_power_ioctl] Set sdio wifi power up!
  1483. [ 55.896886@1] aml_wifi wifi: [wifi_power_ioctl] wifi interface dev type: sdio, length = 4
  1484. [ 56.999540@3] dhd_module_init: in Dongle Host Driver, version 100.10.315.3 (r771911)
  1485. [ 57.001669@3] ======== dhd_wlan_init_plat_data ========
  1486. [ 57.007050@3] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=73, oob_irq_flags=0x418
  1487. [ 57.014540@3] dhd_wlan_init_gpio: WL_REG_ON=-1
  1488. [ 57.018885@3] dhd_wifi_platform_load: Enter
  1489. [ 57.023116@3] Power-up adapter 'DHD generic adapter'
  1490. [ 57.028027@3] wifi_platform_set_power = 1
  1491. [ 57.032002@3] ======== PULL WL_REG_ON(-1) HIGH! ========
  1492. [ 57.037279@3] aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 482
  1493. [ 57.244219@3] aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 482
  1494. [ 57.750578@3] wifi_platform_bus_enumerate device present 1
  1495. [ 57.750613@3] ======== Card detection to detect SDIO card! ========
  1496. [ 57.756706@3] sdio_reset_comm():
  1497. [ 57.759932@3] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0
  1498. [ 57.769618@3] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
  1499. [ 57.775601@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
  1500. [ 57.784717@3] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0
  1501. [ 57.792316@3] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
  1502. [ 57.798322@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
  1503. [ 57.806387@3] meson-mmc: actual_clock :400000, HHI_nand: 0x80
  1504. [ 57.811029@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
  1505. [ 57.820872@3] meson-mmc: actual_clock :0, HHI_nand: 0x80
  1506. [ 57.823341@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
  1507. [ 57.850344@3] meson-mmc: actual_clock :400000, HHI_nand: 0x80
  1508. [ 57.850452@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
  1509. [ 57.875432@3] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
  1510. [ 57.880345@3] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
  1511. [ 57.883803@3] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
  1512. [ 57.989198@2] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0
  1513. [ 57.993341@2] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
  1514. [ 58.001574@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
  1515. [ 58.006711@2] meson-mmc: Data 1 aligned delay is 0
  1516. [ 58.012772@2] meson-mmc: sdio: clk 199999997 tuning start
  1517. [ 58.018189@2] meson-mmc: sdio: rx_tuning_result[0] = 40
  1518. [ 58.024841@3] meson-mmc: sdio: rx_tuning_result[1] = 40
  1519. [ 58.027969@3] meson-mmc: sdio: rx_tuning_result[2] = 40
  1520. [ 58.032143@3] meson-mmc: Tuning transfer error: nmatch=1 tuning_err:0xffffffac
  1521. [ 58.040420@3] meson-mmc: sdio: rx_tuning_result[4] = 40
  1522. [ 58.044470@3] meson-mmc: sdio: best_win_start =4, best_win_size =4
  1523. [ 58.050609@3] meson-mmc: sdio: sd_emmc_regs->gclock=0x10000245,sd_emmc_regs->gadjust=0x12000
  1524. [ 58.059032@3] meson-mmc: [sdio_reinit] finish
  1525. [ 58.080646@3] bcmsdh_sdmmc_probe: Enter num=1
  1526. [ 58.080779@3] bcmsdh_sdmmc_probe: Enter num=2
  1527. [ 58.083755@3] bus num (host idx)=2, slot num (rca)=1
  1528. [ 58.088679@3] found adapter info 'DHD generic adapter'
  1529. [ 58.093786@3] Wifi: bcmdhd_mem_prealloc: sectoin 3, size 139264
  1530. [ 58.099701@3] succeed to alloc static buf
  1531. [ 58.103672@3] Wifi: bcmdhd_mem_prealloc: sectoin 4, size 0
  1532. [ 58.109216@3] sdioh_attach: set sd_f2_blocksize 256
  1533. [ 58.114038@3] sdioh_attach: sd clock rate = 0
  1534. [ 58.118691@3] dhdsdio_probe : no mutex held. set lock
  1535. [ 58.123535@3] F1 signature read @0x18000000=0x16024335
  1536. [ 58.133202@3] F1 signature OK, socitype:0x1 chip:0x4339 rev:0x1 pkg:0x0
  1537. [ 58.135735@3] DHD: dongle ram size is set to 786432(orig 786432) at 0x180000
  1538. [ 58.142209@2] Wifi: bcmdhd_mem_prealloc: sectoin 7, size 24928
  1539. [ 58.147889@2] dhd_conf_set_chiprev: chip=0x4339, chiprev=1
  1540. [ 58.153386@2] Wifi: bcmdhd_mem_prealloc: sectoin 0, size 10320
  1541. [ 58.159905@2] Wifi: bcmdhd_mem_prealloc: sectoin 5, size 65536
  1542. [ 58.165453@2] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
  1543. [ 58.172823@2] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
  1544. [ 58.180692@2] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
  1545. [ 58.188563@2] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
  1546. [ 58.196451@2] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
  1547. [ 58.204340@2] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
  1548. [ 58.212234@2] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
  1549. [ 58.220134@2] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
  1550. [ 58.228020@2] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
  1551. [ 58.235918@2] wl_escan_attach: Enter
  1552. [ 58.239464@2] Wifi: bcmdhd_mem_prealloc: sectoin 19, size 67244
  1553. [ 58.245358@2] wl_escan_init: Enter
  1554. [ 58.248881@2] wl_create_event_handler(): thread:wl_escan_handler:e23 started
  1555. [ 58.248894@3] tsk Enter, tsk = 0xcde30160
  1556. [ 58.259759@2] Wifi: bcmdhd_mem_prealloc: sectoin 20, size 262144
  1557. [ 58.265797@2] Wifi: bcmdhd_mem_prealloc: sectoin 22, size 65536
  1558. [ 58.271754@2] dhd_attach(): thread:dhd_watchdog_thread:e24 started
  1559. [ 58.277897@2] dhd_attach(): thread:dhd_dpc:e25 started
  1560. [ 58.282945@2] dhd_attach(): thread:dhd_rxf:e26 started
  1561. [ 58.288028@2] dhd_deferred_work_init: work queue initialized
  1562. [ 58.293622@2] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 2
  1563. [ 58.300340@2] dhd_get_memdump_info: MEMDUMP ENABLED = 0
  1564. [ 58.305517@2] Wifi: bcmdhd_mem_prealloc: sectoin 1, size 10300
  1565. [ 58.311327@2] Wifi: bcmdhd_mem_prealloc: sectoin 2, size 65536
  1566. [ 58.317453@2] sdioh_cis_read: func_cis_ptr[0]=0x10ac
  1567. [ 58.337669@3] Dongle Host Driver, version 100.10.315.3 (r771911)
  1568. [ 58.339035@3] ANDROID-MSG) wl_ext_iapsta_attach_netdev: ifidx=0, bssidx=0
  1569. [ 58.344853@3] Register interface [wlan0] MAC: f4:09:d8:7e:44:48
  1570. [ 58.344853@3]
  1571. [ 58.352547@3] dhd_dbg_detach_pkt_monitor, 1914
  1572. [ 58.356887@3] dhd_bus_devreset: == Power OFF ==
  1573. [ 58.362174@1] dhd_txglom_enable: enable 0
  1574. [ 58.365525@1] dhd_conf_set_txglom_params: txglom_mode=copy
  1575. [ 58.370843@1] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0
  1576. [ 58.377914@1] dhd_conf_set_txglom_params: txinrx_thres=128, dhd_txminmax=-1
  1577. [ 58.384608@1] dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=300
  1578. [ 58.391549@1] dhd_bus_devreset: WLAN OFF DONE
  1579. [ 58.396071@2] wifi_platform_set_power = 0
  1580. [ 58.399953@2] ======== PULL WL_REG_ON(-1) LOW! ========
  1581. [ 58.405141@2] wl_escan_deinit: Enter
  1582. [ 58.408736@2] wl_destroy_event_handler(): thread:wl_escan_handler:e23 wait for terminate
  1583. [ 58.408750@1] wl_escan_event_handler: was terminated
  1584. [ 58.421724@2] wl_destroy_event_handler(): thread:wl_escan_handler:e23 terminated OK
  1585. [ 58.429347@2] dhdsdio_probe : the lock is released.
  1586. [ 58.434504@2] dhd_module_init: Exit err=0
  1587. [ 62.486380@0] fb: mem_free_work, free memory: addr:800000
  1588. [ 67.023599@2] dhd_open: Enter ec90a000
  1589. [ 67.023629@2] dhd_open : no mutex held. set lock
  1590. [ 67.026733@2]
  1591. [ 67.026733@2] Dongle Host Driver, version 100.10.315.3 (r771911)
  1592. [ 67.034169@2] ANDROID-MSG) wl_ext_iapsta_attach_netdev: ifidx=0, bssidx=0
  1593. [ 67.040906@2] wl_android_wifi_on in 1
  1594. [ 67.044521@2] wl_android_wifi_on in 2: g_wifi_on=0
  1595. [ 67.049275@2] wifi_platform_set_power = 1
  1596. [ 67.053208@2] ======== PULL WL_REG_ON(-1) HIGH! ========
  1597. [ 67.058448@2] aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 482
  1598. [ 67.265565@2] aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 482
  1599. [ 67.774278@2] sdio_reset_comm():
  1600. [ 67.774342@2] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0
  1601. [ 67.781636@2] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
  1602. [ 67.787581@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
  1603. [ 67.796757@2] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0
  1604. [ 67.804373@2] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
  1605. [ 67.810314@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
  1606. [ 67.818396@2] meson-mmc: actual_clock :400000, HHI_nand: 0x80
  1607. [ 67.823028@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
  1608. [ 67.832978@2] meson-mmc: actual_clock :0, HHI_nand: 0x80
  1609. [ 67.835339@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
  1610. [ 67.862383@2] meson-mmc: actual_clock :400000, HHI_nand: 0x80
  1611. [ 67.862489@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
  1612. [ 67.887571@2] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
  1613. [ 67.892490@2] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
  1614. [ 67.896040@2] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
  1615. [ 67.998471@2] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0
  1616. [ 68.002621@2] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
  1617. [ 68.008613@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
  1618. [ 68.015787@2] meson-mmc: Data 1 aligned delay is 0
  1619. [ 68.020412@2] meson-mmc: sdio: clk 199999997 tuning start
  1620. [ 68.027008@3] meson-mmc: sdio: rx_tuning_result[0] = 40
  1621. [ 68.032253@3] meson-mmc: sdio: rx_tuning_result[1] = 40
  1622. [ 68.037395@3] meson-mmc: sdio: rx_tuning_result[2] = 40
  1623. [ 68.041357@2] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
  1624. [ 68.049768@2] meson-mmc: sdio: rx_tuning_result[4] = 40
  1625. [ 68.053735@2] meson-mmc: sdio: best_win_start =4, best_win_size =4
  1626. [ 68.059891@2] meson-mmc: sdio: sd_emmc_regs->gclock=0x10000245,sd_emmc_regs->gadjust=0x12000
  1627. [ 68.068410@2] sdioh_start: set sd_f2_blocksize 256
  1628. [ 68.073503@3]
  1629. [ 68.073503@3]
  1630. [ 68.073503@3] dhd_bus_devreset: == WLAN ON ==
  1631. [ 68.080828@3] F1 signature read @0x18000000=0x16024335
  1632. [ 68.090647@3] F1 signature OK, socitype:0x1 chip:0x4339 rev:0x1 pkg:0x0
  1633. [ 68.093044@3] DHD: dongle ram size is set to 786432(orig 786432) at 0x180000
  1634. [ 70.733270@1] dhd_os_open_image1: /vendor/etc/wifi/6335/config.txt (102 bytes) open success
  1635. [ 70.761290@1] dhd_conf_read_sdio_params: dhd_slpauto = 0
  1636. [ 70.761346@1] dhd_conf_read_others: ccode = XS
  1637. [ 70.766175@1] dhd_conf_read_others: regrev = 0
  1638. [ 70.775574@1] Final fw_path=/vendor/etc/wifi/6335/fw_bcm4339a0_ag.bin
  1639. [ 70.776420@1] Final nv_path=/vendor/etc/wifi/6335/nvram_ap6335.txt
  1640. [ 70.783315@1] Final clm_path=/vendor/etc/wifi/6335/clm.blob
  1641. [ 70.788249@1] Final conf_path=/vendor/etc/wifi/6335/config.txt
  1642. [ 70.800582@2] dhd_os_open_image1: /vendor/etc/wifi/6335/fw_bcm4339a0_ag.bin (543862 bytes) open success
  1643. [ 70.939103@0] dhd_os_open_image1: /vendor/etc/wifi/6335/nvram_ap6335.txt (2994 bytes) open success
  1644. [ 70.955811@0] NVRAM version: hs2735F
  1645. [ 70.958541@2] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
  1646. [ 71.105375@1] BT_RADIO going: on
  1647. [ 71.105407@1] AML_BT: going ON
  1648. [ 71.131597@1] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
  1649. [ 71.132731@1] bcmsdh_oob_intr_register: HW_OOB irq=73 flags=0x8
  1650. [ 71.138311@1] dhd_get_memdump_info: MEMDUMP ENABLED = 0
  1651. [ 71.144792@1] Disable tdls_auto_op failed. -1
  1652. [ 71.147486@1] dhd_tcpack_suppress_set: TCP ACK Suppress mode 2 -> mode 1
  1653. [ 71.154763@1] dhd_apply_default_clm: Ignore clm file /vendor/etc/wifi/6335/clm.blob
  1654. [ 71.171855@3] Firmware up: op_mode=0x0005, MAC=f4:09:d8:7e:44:48
  1655. [ 71.184437@1] dhd_preinit_ioctls event_msgs_ext not support or version mismatch -23
  1656. [ 71.194583@3] Driver: 100.10.315.3 (r771911)
  1657. [ 71.194583@3] Firmware: wl0: Dec 6 2013 15:47:10 version 6.37.32.RC23.34.10 (r)
  1658. [ 71.194583@3] CLM: 6.8.1
  1659. [ 71.204307@3] dhd_txglom_enable: enable 1
  1660. [ 71.207907@3] dhd_conf_set_txglom_params: txglom_mode=copy
  1661. [ 71.213326@3] dhd_conf_set_txglom_params: txglomsize=36, deferred_tx_len=0
  1662. [ 71.220150@3] dhd_conf_set_txglom_params: txinrx_thres=128, dhd_txminmax=-1
  1663. [ 71.227115@3] dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=300
  1664. [ 71.234113@3] dhd_conf_get_disable_proptx: fw_proptx=1, disable_proptx=-1
  1665. [ 71.241707@1] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64
  1666. [ 71.249174@2] dhd_pno_init: Support Android Location Service
  1667. [ 71.295908@0] dhd_wlfc_enable: ret=0
  1668. [ 71.295958@0] CFG80211-ERROR) wl_cfg80211_event : Event handler is not created
  1669. [ 71.301289@0] CFG80211-ERROR) wl_cfg80211_event : Event handler is not created
  1670. [ 71.308583@2] rtt_do_get_ioctl: failed to send getbuf proxd iovar (CMD ID : 1), status=-23
  1671. [ 71.316595@2] dhd_rtt_init : FTM is not supported
  1672. [ 71.322895@2] dhd_wl_ioctl_get_intiovar: get int iovar wnm_bsstrans_resp failed, ERR -23
  1673. [ 71.329320@2] failed to get wnm_bsstrans_resp
  1674. [ 71.334063@2] failed to set WNM capabilities
  1675. [ 71.350541@0] dhd_preinit_ioctls: Failed to get preserve log # !
  1676. [ 71.351269@2] dhd_wlfc_enable: ret=0
  1677. [ 71.351288@0] dhd_conf_set_country: set country XS, revision 0
  1678. [ 71.360393@0] CFG80211-ERROR) wl_cfg80211_event : Event handler is not created
  1679. [ 71.367796@1] CFG80211-ERROR) wl_cfg80211_event : Event handler is not created
  1680. [ 71.375847@3] Country code: XS (XS/0)
  1681. [ 71.381628@3] wl_android_wifi_on: Success
  1682. [ 71.429396@0] dhd_wlfc_enable: ret=0
  1683. [ 71.453879@3] wl_escan_init: Enter
  1684. [ 71.454040@0] wl_create_event_handler(): thread:wl_escan_handler:eda started
  1685. [ 71.454047@3] tsk Enter, tsk = 0xcde30160
  1686. [ 71.463412@0] dhd_open : the lock is released.
  1687. [ 71.467820@0] dhd_open: Exit ret=0
  1688. [ 71.518763@1] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600
  1689. [ 71.521282@0] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 9600
  1690. [ 71.529629@2] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200
  1691. [ 71.543579@1] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 115200 to 2000000
  1692. [ 71.608923@1] P2P interface registered
  1693. [ 71.608956@1] wl_cfgp2p_add_p2p_disc_if: wdev: eac92000, wdev->net: (null)
  1694. [ 71.629936@1] WLC_E_IF: NO_IF set, event Ignored
  1695. [ 73.897036@3] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 2000000 to 115200
  1696. [ 74.106134@3] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 115200 to 2000000
  1697. [ 74.316667@1] zram0: detected capacity change from 0 to 268435456
  1698. [ 74.354548@0] mkswap: Swapspace size: 262140k, UUID=a7bfa5b1-1cbe-4cd5-8e31-7ab02e9da5c5
  1699. [ 74.357597@0] Adding 262140k swap on /dev/block/zram0. Priority:-1 extents:1 across:262140k SS
  1700. [ 74.371708@2] selinux: SELinux: Skipping restorecon_recursive(/data/system_ce/0)
  1701. [ 74.371708@2]
  1702. [ 74.503965@1] selinux: SELinux: Skipping restorecon_recursive(/data/misc_ce/0)
  1703. [ 74.503965@1]
  1704. [ 74.597758@3] read descriptors
  1705. [ 74.597801@3] read strings
  1706. [ 97.888388@2] Random MAC OUI to be used - da:1:19
  1707. [ 97.894300@1] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1708. [ 97.895714@2] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1709. [ 97.904726@1] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1710. [ 97.914083@0] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1711. [ 97.916313@2] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1712. [ 97.923198@2] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1713. [ 97.928095@0] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1714. [ 97.934615@1] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1715. [ 97.940651@1] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1716. [ 97.946969@1] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1717. [ 97.953299@1] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1718. [ 97.959552@1] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1719. [ 97.965895@3] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1720. [ 97.974139@3] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1721. [ 97.978665@1] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1722. [ 97.984916@1] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1723. [ 97.991321@1] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1724. [ 97.997575@3] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1725. [ 98.003883@3] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1726. [ 98.010224@3] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1727. [ 98.016491@3] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1728. [ 98.022874@3] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1729. [ 98.029147@3] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1730. [ 98.035460@3] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1731. [ 98.041761@3] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1732. [ 98.048193@3] dhd_dbg_set_event_log_tag set log tag iovar failed -23
  1733. [ 98.055620@3] dhd_dbg_attach_pkt_monitor, 1316
  1734. [ 98.061996@3] net_os_enable_packet_filter: val = 0
  1735. [ 98.064628@3] net_os_rxfilter_add_remove: add_remove = 0, num = 2
  1736. [ 98.071046@3] net_os_enable_packet_filter: val = 1
  1737. [ 98.075253@3] net_os_enable_packet_filter: val = 0
  1738. [ 98.079857@3] net_os_rxfilter_add_remove: add_remove = 0, num = 3
  1739. [ 98.086508@3] net_os_enable_packet_filter: val = 1
  1740. [ 98.090684@3] dhd_set_suspend: Remove extra suspend setting
  1741. [ 98.095550@3] dhd_enable_packet_filter: enter, value = 0
  1742. [ 98.166844@3] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 0, bssidx: 0
  1743. [ 101.186999@3] audio_dsp: dts_dec_control/0x0
  1744. [ 101.747417@1] audio_dsp: drc high cut scale set to 100%
  1745. [ 101.747977@1] audio_dsp: drc low boost scale set to 100%
  1746. [ 101.753056@0] audio_dsp: drc mode set to LINE
  1747. [ 102.465831@0] [wlan0] wl_escan_handler : SCAN COMPLETED: scanned AP count=11
  1748. [ 106.479512@2] type=1400 audit(1420070453.308:19): avc: denied { getattr } for pid=3414 comm="android.ui" path="/sys/devices/virtual/amhdmitx/amhdmitx0/hdmi/state" dev="sysfs" ino=9508 scontext=u:r:system_server:s0 tcontext=u:object_r:sysfs_amhdmitx:s0 tclass=file permissive=1
  1749. [ 106.645089@2] type=1400 audit(1420070511.124:20): avc: denied { execute } for pid=4737 comm="Thread-2" name="su" dev="mmcblk0p18" ino=593 scontext=u:r:priv_app:s0:c512,c768 tcontext=u:object_r:su_exec:s0 tclass=file permissive=1
  1750. [ 106.817612@2] type=1400 audit(1420070511.124:20): avc: denied { execute } for pid=4737 comm="Thread-2" name="su" dev="mmcblk0p18" ino=593 scontext=u:r:priv_app:s0:c512,c768 tcontext=u:object_r:su_exec:s0 tclass=file permissive=1
  1751. [ 106.954406@2] type=1400 audit(1420070511.124:21): avc: denied { read open } for pid=4737 comm="Thread-2" path="/system/xbin/su" dev="mmcblk0p18" ino=593 scontext=u:r:priv_app:s0:c512,c768 tcontext=u:object_r:su_exec:s0 tclass=file permissive=1
  1752. [ 107.006509@0] type=1400 audit(1420070511.124:21): avc: denied { read open } for pid=4737 comm="Thread-2" path="/system/xbin/su" dev="mmcblk0p18" ino=593 scontext=u:r:priv_app:s0:c512,c768 tcontext=u:object_r:su_exec:s0 tclass=file permissive=1
  1753. [ 107.023348@0] type=1400 audit(1420070511.124:22): avc: denied { execute_no_trans } for pid=4737 comm="Thread-2" path="/system/xbin/su" dev="mmcblk0p18" ino=593 scontext=u:r:priv_app:s0:c512,c768 tcontext=u:object_r:su_exec:s0 tclass=file permissive=1
  1754. [ 109.683222@1] type=1400 audit(1420070511.124:22): avc: denied { execute_no_trans } for pid=4737 comm="Thread-2" path="/system/xbin/su" dev="mmcblk0p18" ino=593 scontext=u:r:priv_app:s0:c512,c768 tcontext=u:object_r:su_exec:s0 tclass=file permissive=1
  1755. [ 109.700288@1] type=1400 audit(1420070514.324:23): avc: denied { search } for pid=3145 comm="memtrack@1.0-se" name="3126" dev="proc" ino=1523 scontext=u:r:hal_memtrack_default:s0 tcontext=u:r:hal_allocator_default:s0 tclass=dir permissive=1
  1756. [ 109.723639@1] type=1400 audit(1420070514.324:23): avc: denied { search } for pid=3145 comm="memtrack@1.0-se" name="3126" dev="proc" ino=1523 scontext=u:r:hal_memtrack_default:s0 tcontext=u:r:hal_allocator_default:s0 tclass=dir permissive=1
  1757. [ 109.742466@1] type=1400 audit(1420070514.328:24): avc: denied { read } for pid=3145 comm="memtrack@1.0-se" name="status" dev="proc" ino=34748 scontext=u:r:hal_memtrack_default:s0 tcontext=u:r:hal_allocator_default:s0 tclass=file permissive=1
  1758. [ 110.057131@0] audit: audit_lost=3 audit_rate_limit=5 audit_backlog_limit=64
  1759. [ 110.058716@0] audit: rate limit exceeded
  1760. [ 111.086189@1] audit: audit_lost=11 audit_rate_limit=5 audit_backlog_limit=64
  1761. [ 111.087682@1] audit: rate limit exceeded
  1762. [ 115.380306@0] binder_alloc: 3937: binder_alloc_buf size 1056768 failed, no address space
  1763. [ 115.382834@0] binder_alloc: allocated: 1720 (num: 9 largest: 1660), free: 1038664 (num: 6 largest: 1035100)
  1764. [ 115.393541@0] binder: 4159:4318 transaction failed 29201/-28, size 1056768-0 line 3258
  1765. [ 120.749864@1] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 1, bssidx: 0
  1766. [ 125.016924@2] [wlan0] wl_escan_handler : SCAN COMPLETED: scanned AP count=14
  1767.  
  1768. console:/ # free -h
  1769. total used free shared buffers
  1770. Mem: 3.3G 1.3G 2.0G 736K 17M
  1771. -/+ buffers/cache: 1.3G 2.0G
  1772. Swap: 256M 0 256M
  1773. console:/ # df -h
  1774. Filesystem Size Used Avail Use% Mounted on
  1775. /d[e v /1r55.596093@1] type=1400 audit(1420070515.728:43): avc: denied { search } for pid=3145 comm="memtrack@1.0-se" name="3224" dev="proc" ino=15452 scontext=u:r:hal_memtrack_default:s0 tcontext=u:r:storaged:s0 tclass=dir permissive=1
  1776. [ 155.616779@1] type=1400 audit(1420070560.236:47): avc: denied { getattr } for pid=5557 comm="df" path="/mnt/vendor/param" dev="mmcblk0p10" ino=2 scontext=u:r:shell:s0 tcontext=u:object_r:param_tv_file:s0 tclass=dir permissive=1
  1777. oot 1.7G 1.4G 376M 80% /
  1778. tmpfs 1.6G 460K 1.6G 1% /dev
  1779. tmpfs 1.6G 0 1.6G 0% /mnt
  1780. /dev/block/odm 124M 508K 123M 1% /odm
  1781. /dev/block/product 124M 3.5M 120M 3% /product
  1782. /dev/block/vendor 310M 224M 86M 73% /vendor
  1783. /dev/block/data 53G 893M 52G 2% /data
  1784. /dev/block/cache 1.0G 1.3M 1.0G 1% /cache
  1785. /dev/block/metadata 11M 40K 11M 1% /metadata
  1786. /dev/block/param 11M 764K 11M 7% /mnt/vendor/param
  1787. /dev/block/tee 27M 28K 27M 1% /mnt/vendor/tee
  1788. /data/media 53G 893M 52G 2% /mnt/runtime/default/emulated
  1789. console:/ # ifconfig[ 168.464997@1] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 2, bssidx: 0
  1790. -a
  1791. [ 170.780410@1] type=1400 audit(1420070560.236:47): avc: denied { getattr } for pid=5557 comm="df" path="/mnt/vendor/param" dev="mmcblk0p10" ino=2 scontext=u:r:shell:s0 tcontext=u:object_r:param_tv_file:s0 tclass=dir permissive=1
  1792. [ 170.795054@1] type=1400 audit(1420070575.424:48): avc: denied { net_raw } for pid=5563 comm="ifconfig" capability=13 scontext=u:r:shell:s0 tcontext=u:r:shell:s0 tclass=capability permissive=1
  1793. [ 170.812374@1] type=1400 audit(1420070575.424:48): avc: denied { net_raw } for pid=5563 comm="ifconfig" capability=13 scontext=u:r:shell:s0 tcontext=u:r:shell:s0 tclass=capability permissive=1
  1794. [ 170.829888@1] type=1400 audit(1420070575.424:49): avc: denied { ioctl } for pid=5563 comm="ifconfig" path="socket:[47843]" dev="sockfs" ino=47843 ioctlcmd=0x8927 scontext=u:r:shell:s0 tcontext=u:r:shell:s0 tclass=udp_socket permissive=1
  1795. [ 170.850716@1] type=1400 audit(1420070575.424:49): avc: denied { ioctl } for pid=5563 comm="ifconfig" path="socket:[47843]" dev="sockfs" ino=47843 ioctlcmd=0x8927 scontext=u:r:shell:s0 tcontext=u:r:shell:s0 tclass=udp_socket permissive=1
  1796. [ 170.870796@1] type=1400 audit(1420070575.424:50): avc: denied { ioctl } for pid=5563 comm="ifconfig" path="socket:[47843]" dev="sockfs" ino=47843 ioctlcmd=0x891d scontext=u:r:shell:s0 tcontext=u:r:shell:s0 tclass=udp_socket permissive=1
  1797. [ 170.891940@1] type=1400 audit(1420070575.424:50): avc: denied { ioctl } for pid=5563 comm="ifconfig" path="socket:[47843]" dev="sockfs" ino=47843 ioctlcmd=0x891d scontext=u:r:shell:s0 tcontext=u:r:shell:s0 tclass=udp_socket permissive=1
  1798. [ 170.912598@1] type=1400 audit(1420070575.424:51): avc: denied { ioctl } for pid=5563 comm="ifconfig" path="socket:[47843]" dev="sockfs" ino=47843 ioctlcmd=0x8970 scontext=u:r:shell:s0 tcontext=u:r:shell:s0 tclass=udp_socket permissive=1
  1799. sit0 Link encap:IPv6-in-IPv4
  1800. NOARP MTU:1480 Metric:1
  1801. RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  1802. TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  1803. collisions:0 txqueuelen:1
  1804. RX bytes:0 TX bytes:0
  1805.  
  1806. ip6_vti0 Link encap:UNSPEC
  1807. NOARP MTU:1500 Metric:1
  1808. RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  1809. TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  1810. collisions:0 txqueuelen:1
  1811. RX bytes:0 TX bytes:0
  1812.  
  1813. tunl0 Link encap:UNSPEC
  1814. NOARP MTU:1480 Metric:1
  1815. RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  1816. TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  1817. collisions:0 txqueuelen:1
  1818. RX bytes:0 TX bytes:0
  1819.  
  1820. wlan0 Link encap:Ethernet HWaddr f4:09:d8:7e:44:48 Driver bcmsdh_sdmmc
  1821. UP BROADCAST MULTICAST MTU:1500 Metric:1
  1822. RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  1823. TX packets:23 errors:0 dropped:0 overruns:0 carrier:0
  1824. collisions:0 txqueuelen:1000
  1825. RX bytes:0 TX bytes:4207
  1826.  
  1827. lo Link encap:Local Loopback
  1828. inet addr:127.0.0.1 Mask:255.0.0.0
  1829. inet6 addr: ::1/128 Scope: Host
  1830. UP LOOPBACK RUNNING MTU:65536 Metric:1
  1831. RX packets:67 errors:0 dropped:0 overruns:0 frame:0
  1832. TX packets:67 errors:0 dropped:0 overruns:0 carrier:0
  1833. collisions:0 txqueuelen:1
  1834. RX bytes:11264 TX bytes:11264
  1835.  
  1836. eth0 Link encap:Ethernet HWaddr 00:df:12:00:a3:31 Driver meson6-dwmac
  1837. UP BROADCAST MULTICAST MTU:1500 Metric:1
  1838. RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  1839. TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  1840. collisions:0 txqueuelen:1000
  1841. RX bytes:0 TX bytes:0
  1842. Interrupt:28
  1843.  
  1844. ip6tnl0 Link encap:UNSPEC
  1845. NOARP MTU:1452 Metric:1
  1846. RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  1847. TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  1848. collisions:0 txqueuelen:1
  1849. RX bytes:0 TX bytes:0
  1850.  
  1851. ip_vti0 Link encap:UNSPEC
  1852. NOARP MTU:1480 Metric:1
  1853. RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  1854. TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  1855. collisions:0 txqueuelen:1
  1856. RX bytes:0 TX bytes:0
  1857.  
  1858. console:/ # [ 172.735992@1] [wlan0] wl_escan_handler : SCAN COMPLETED: scanned AP count=11
  1859. uname -a
  1860. Linux localhost 4.9.113 #1 SMP PREEMPT Mon Jan 13 11:39:18 CST 2020 armv7l
  1861. console:/ # cat /dev/cpu
  1862. cpu_dma_latency cpuctl/ cpuset/
  1863. console:/ # cat /proc/cpu
  1864. cpu/ cpuinfo
  1865. console:/ # cat /proc/cpuinfo
  1866. processor : 0
  1867. model name : ARMv7 Processor rev 0 (v7l)
  1868. BogoMIPS : 56.16
  1869. Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm aes pmull sha1 sha2 crc32
  1870. CPU implementer : 0x41
  1871. CPU architecture: 7
  1872. CPU variant : 0x1
  1873. CPU part : 0xd05
  1874. CPU revision : 0
  1875.  
  1876. processor : 1
  1877. model name : ARMv7 Processor rev 0 (v7l)
  1878. BogoMIPS : 56.16
  1879. Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm aes pmull sha1 sha2 crc32
  1880. CPU implementer : 0x41
  1881. CPU architecture: 7
  1882. CPU variant : 0x1
  1883. CPU part : 0xd05
  1884. CPU revision : 0
  1885.  
  1886. processor : 2
  1887. model name : ARMv7 Processor rev 0 (v7l)
  1888. BogoMIPS : 56.16
  1889. Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm aes pmull sha1 sha2 crc32
  1890. CPU implementer : 0x41
  1891. CPU architecture: 7
  1892. CPU variant : 0x1
  1893. CPU part : 0xd05
  1894. CPU revision : 0
  1895.  
  1896. processor : 3
  1897. model name : ARMv7 Processor rev 0 (v7l)
  1898. BogoMIPS : 56.16
  1899. Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm aes pmull sha1 sha2 crc32
  1900. CPU implementer : 0x41
  1901. CPU architecture: 7
  1902. CPU variant : 0x1
  1903. CPU part : 0xd05
  1904. CPU revision : 0
  1905.  
  1906. Serial : 2b0c100001170c00000c3139574b5250
  1907. Hardware : Amlogic
  1908.  
  1909. console:/ # [ 248.454375@2] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 3, bssidx: 0
  1910. [ 252.726417@0] [wlan0] wl_escan_handler : SCAN COMPLETED: scanned AP count=11
  1911.  
  1912.  
  1913. ---------- 2021-01-08 21:53:30 +0100: Logging Stopped ----------
Add Comment
Please, Sign In to add comment
Public Pastes
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!