Guest User

Untitled

a guest
Nov 1st, 2018
1,117
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. GXM:BL1:dc8b51:76f1a5;FEAT:ADFD718C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
  2. TE: 217662
  3.  
  4. BL2 Built : 11:04:41, Jan 26 2018.
  5. gxl g034b32c - xingyu.chen@droid12-sz
  6.  
  7. set vdd cpu_a to 1120 mv
  8. set vdd cpu_b to 1050 mv
  9. set vddee to 1000 mv
  10. Board ID = 1
  11. CPU clk: 1200MHz
  12. DQS-corr enabled
  13. DDR scramble enabled
  14. DDR3 chl: Rank0+1 @ 912MHz
  15. bist_test rank: 0 1a 00 34 32 1d 47 17 00 2f 38 20 50 18 00 31 30 19 48 1e 02 3a 2d 12 48 660 rank: 1 19 04 2e 33 1d 49 14 00 28 38 20 50 17 00 2f 31 1a 48 1e 07 35 2d 13 48 660 - PASS
  16.  
  17. Rank0: 1024MB(auto)-2T-13
  18.  
  19. Rank1: 1024MB(auto)-2T-13
  20. AddrBus test pass!
  21. -s
  22. Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
  23. New fip structure!
  24. Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
  25. Load bl31 from eMMC, src: 0x00020200, des: 0x05100000, size: 0x0002c600
  26. Load bl32 from eMMC, src: 0x00050200, des: 0x05300000, size: 0x00036600
  27. Load bl33 from eMMC, src: 0x00088200, des: 0x01000000, size: 0x00053000
  28. NOTICE: BL3-1: v1.0(release):35dd647
  29. NOTICE: BL3-1: Built : 15:20:30, Feb 7 2018
  30. NOTICE: BL31: BL33 decompress pass
  31. mpu_config_enable:ok
  32.  
  33. [Image: gxl_v1.1.3243-377db0f 2017-09-07 11:28:58 qiufang.dai@droid07]
  34.  
  35. OPS=0x82
  36.  
  37. wdt: reset registers!
  38.  
  39. 51 ff eb 27 fe e0 e6 a9 65 38 ca 8f [0.682951 Inits done]
  40.  
  41. secure task start!
  42. high task start!
  43. low task start!
  44. INFO: BL3-2: ATOS-V2.0.2-g4bffb3e #1 Wed Sep 27 19:06:53 CST 2017 arm
  45. INFO: BL3-2: Chip: Unknown Rev: A (22:A - 80:2)
  46. INFO: BL3-2: crypto engine DMA
  47. INFO: BL3-2: secure time TEE
  48. INFO: BL3-2: CONFIG_DEVICE_SECURE 0xb200000e
  49.  
  50.  
  51. U-Boot 2015.01-gd4767ac-dirty (Aug 14 2018 - 12:19:03)
  52.  
  53. DRAM: 2 GiB
  54. Relocation Offset is: 76ed6000
  55. register usb cfg[0][1] = 0000000077f5cf98
  56. [CANVAS]canvas init
  57. MMC: aml_priv->desc_buf = 0x0000000073ed6640
  58. aml_priv->desc_buf = 0x0000000073ed8960
  59. SDIO Port B: 0, SDIO Port C: 1
  60. emmc/sd response timeout, cmd8, status=0x3ff2800
  61. emmc/sd response timeout, cmd55, status=0x3ff2800
  62. init_part() 293: PART_TYPE_AML
  63. [mmc_init] mmc init success
  64. dtb magic edfe0dd0
  65. start dts,buffer=0000000073edb1b0,dt_addr=0000000073edb1b0
  66. parts: 11
  67. 00: logo 0000000002000000 1
  68. 01: recovery 0000000002000000 1
  69. 02: rsv 0000000000800000 1
  70. 03: tee 0000000000800000 1
  71. 04: crypt 0000000002000000 1
  72. 05: misc 0000000002000000 1
  73. 06: instaboot 0000000020000000 1
  74. 07: boot 0000000002000000 1
  75. 08: system 0000000040000000 1
  76. 09: cache 0000000020000000 2
  77. 10: data ffffffffffffffff 4
  78. init_part() 293: PART_TYPE_AML
  79. eMMC/TSD partition table have been checked OK!
  80. check pattern success
  81. mmc env offset: 0x27400000
  82. In: serial
  83. Out: serial
  84. Err: serial
  85. reboot_mode=cold_boot
  86. [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
  87. _verify_dtb_checksum()-917: calc e2e48a5f, store e2e48a5f
  88. _verify_dtb_checksum()-917: calc e2e48a5f, store e2e48a5f
  89. dtb_read()-1039: total valid 2
  90. dtb_read()-1106: do nothing
  91. vpu: clk_level in dts: 7
  92. vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
  93. vpu: vpu_clk_gate_init_off
  94. vpp: vpp_init
  95. hpd_state=0
  96. cvbs performance type = 6, table = 0
  97. vpp: vpp_pq_load pq val error !!!
  98. Net: Phy 0 not found
  99. dwmac.c9410000amlkey_init() enter!
  100. [EFUSE_MSG]keynum is 4
  101. [BL31]: tee size: 0
  102.  
  103. Start read misc partition datas!
  104. info->attemp_times = 0
  105. info->active_slot = 0
  106. info->slot_info[0].bootable = 1
  107. info->slot_info[0].online = 1
  108. info->slot_info[1].bootable = 0
  109. info->slot_info[1].online = 0
  110. info->attemp_times = 0
  111. attemp_times = 0
  112. active slot = 0
  113. wipe_data=successful
  114. wipe_cache=successful
  115. upgrade_step=2
  116. saradc - saradc sub-system
  117.  
  118. Usage:
  119. saradc saradc open <channel> - open a SARADC channel
  120. saradc close - close the SARADC
  121. saradc getval - get the value in current channel
  122. saradc test - test the SARADC by channel-7
  123. saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
  124.  
  125. [OSD]load fb addr from dts
  126. [OSD]fb_addr for logo: 0x7d851000
  127. [OSD]load fb addr from dts
  128. [OSD]fb_addr for logo: 0x7d851000
  129. [CANVAS]addr=0x7d851000 width=3840, height=2160
  130. amlkey_init() enter!
  131. amlkey_init() 71: already init!
  132. [EFUSE_MSG]keynum is 4
  133. [BL31]: tee size: 0
  134. [KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
  135. [KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet
  136. [KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
  137. gpio: pin GPIOAO_2 (gpio 102) value is 1
  138. Hit Enter or space or Ctrl+C key to stop autoboot -- : 1  0
  139. card out
  140. emmc/sd response timeout, cmd8, status=0x1ff2800
  141. emmc/sd response timeout, cmd55, status=0x1ff2800
  142. emmc/sd response timeout, cmd1, status=0x1ff2800
  143. emmc/sd response timeout, cmd8, status=0x1ff2800
  144. emmc/sd response timeout, cmd55, status=0x1ff2800
  145. emmc/sd response timeout, cmd1, status=0x1ff2800
  146. ** Bad device mmc 0 **
  147. (Re)start USB...
  148. USB0: USB3.0 XHCI init start
  149. Register 3000140 NbrPorts 3
  150. Starting the controller
  151. USB XHCI 1.00
  152. scanning bus 0 for devices... 2 USB Device(s) found
  153. scanning usb for storage devices... 0 Storage Device(s) found
  154. ** Bad device usb 0 **
  155. ee_gate_off ...
  156. ## Booting Android Image at 0x01080000 ...
  157. reloc_addr =73f5b380
  158. copy done
  159. load dtb from 0x1000000 ......
  160. Uncompressing Kernel Image ... OK
  161. kernel loaded at 0x01080000, end = 0x01bb21d8
  162. Loading Ramdisk to 73aa8000, end 73ec4400 ... OK
  163. Loading Device Tree to 000000001fff2000, end 000000001fffff77 ... OK
  164. signature:
  165. fdt_instaboot: no instaboot image
  166.  
  167. Starting kernel ...
  168.  
  169. uboot time: 5773780 us
  170. [ 0.000000@0] Initializing cgroup subsys cpuset
  171. [ 0.000000@0] Initializing cgroup subsys cpu
  172. [ 0.000000@0] Initializing cgroup subsys cpuacct
  173. [ 0.000000@0] Linux version 3.14.29 (imac@imac-Parallels-Virtual-Platform) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP Fri Oct 26 20:38:34 CEST 2018
  174. [ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
  175. [ 0.000000@0] no prop version_code
  176. [ 0.000000@0] bootconsole [earlycon0] enabled
  177. [ 0.000000@0] fdt Reserved memory table:
  178. [ 0.000000@0] linux,di: 0x000000007d300000 - 0x000000007f100000 (30 MiB)
  179. [ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007d300000, size 30 MiB
  180. [ 0.000000@0] linux,ion-dev: 0x0000000079300000 - 0x000000007d300000 (64 MiB)
  181. [ 0.000000@0] linux,vdin1_cma: 0x0000000078000000 - 0x0000000079000000 (16 MiB)
  182. [ 0.000000@0] cma: Reserved 16 MiB at 78000000, total cma pages:4096
  183. [ 0.000000@0] linux,ppmgr: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
  184. [ 0.000000@0] linux,codec_mm_cma: 0x0000000067800000 - 0x0000000073800000 (192 MiB)
  185. [ 0.000000@0] cma: Reserved 192 MiB at 67800000, total cma pages:53248
  186. [ 0.000000@0] linux,picdec: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
  187. [ 0.000000@0] Reserved memory: incorrect alignment of CMA region
  188. [ 0.000000@0] linux,codec_mm_reserved: 0x0000000073f00000 - 0x0000000078000000 (65 MiB)
  189. [ 0.000000@0] fdt Reserved memory total: 403 MiB
  190. [ 0.000000@0] cma: Reserved 8 MiB at 67000000, total cma pages:55296
  191. [ 0.000000@0] psci: probing function IDs from device-tree
  192. [ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc07926c000 s17536 r8192 d23424 u49152
  193. [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 499800
  194. [ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=permissive logo=osd1,loaded,0x3d800000,576cvbs maxcpus=8 vout=576cvbs,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 pq= androidboot.firstboot=0 jtag=apee androidboot.hardware=amlogic androidboot.slot_suffix=_a console=tty0 systemd.show_status=auto ssh
  195. [ 0.000000@0] logo: osd1
  196. [ 0.000000@0] logo: loaded
  197. [ 0.000000@0] logo: 0x3d800000
  198. [ 0.000000@0] logo: 576cvbs
  199. [ 0.000000@0] vout_serve: 576cvbs
  200. [ 0.000000@0] vout_serve: en: 1
  201. [ 0.000000@0] vout_serve: set_vout_init_vmode: 576cvbs
  202. [ 0.000000@0] vout_serve: 576cvbs
  203. [ 0.000000@0] vout_serve: enable: 1
  204. [ 0.000000@0] logo: get hdmimode: 1080p60hz
  205. [ 0.000000@0] logo: get cvbsmode: 576cvbs
  206. [ 0.000000@0] tv_vout: cvbs performance line = 0
  207. [ 0.000000@0] [amvecm] pq string error !!!
  208. [ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
  209. [ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
  210. [ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
  211. [ 0.000000@0] Memory: 1590440K/2043904K available (7065K kernel code, 832K rwdata, 2644K rodata, 913K init, 2908K bss, 453464K reserved)
  212. [ 0.000000@0] Virtual kernel memory layout:
  213. [ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
  214. [ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff8042bbd800 ( 43 MB)
  215. [ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
  216. [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07f100000 ( 2033 MB)
  217. [ 0.000000@0] .init : 0xffffffc0019fd000 - 0xffffffc001ae1480 ( 914 kB)
  218. [ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc0019fc774 ( 9714 kB)
  219. [ 0.000000@0] .data : 0xffffffc001ae2000 - 0xffffffc001bb21d8 ( 833 kB)
  220. [ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x019fbfff]
  221. [ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1
  222. [ 0.000000@0] arch_multi_cluster:1
  223. [ 0.000000@0] Hierarchical RCU implementation.
  224. [ 0.000000@0] RCU debugfs-based tracing is enabled.
  225. [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
  226. [ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
  227. [ 0.000005@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
  228. [ 0.008247@0] meson_bc_timer: mclk->mux_reg =ffffff8000014990,mclk->reg =ffffff8000016994
  229. [ 0.016780@0] Console: colour dummy device 80x25
  230. [ 0.021087@0] console [tty0] enabled
  231. [ 0.024672@0] bootconsole [earlycon0] disabled
  232. domain-0 init dvfs: 4
  233.  
  234. domain-1 init dvfs: 4
  235.  
  236. [ 0.000000@0] Initializing cgroup subsys cpuset
  237. [ 0.000000@0] Initializing cgroup subsys cpu
  238. [ 0.000000@0] Initializing cgroup subsys cpuacct
  239. [ 0.000000@0] Linux version 3.14.29 (imac@imac-Parallels-Virtual-Platform) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP Fri Oct 26 20:38:34 CEST 2018
  240. [ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
  241. [ 0.000000@0] no prop version_code
  242. [ 0.000000@0] bootconsole [earlycon0] enabled
  243. [ 0.000000@0] fdt Reserved memory table:
  244. [ 0.000000@0] linux,di: 0x000000007d300000 - 0x000000007f100000 (30 MiB)
  245. [ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007d300000, size 30 MiB
  246. [ 0.000000@0] linux,ion-dev: 0x0000000079300000 - 0x000000007d300000 (64 MiB)
  247. [ 0.000000@0] linux,vdin1_cma: 0x0000000078000000 - 0x0000000079000000 (16 MiB)
  248. [ 0.000000@0] cma: Reserved 16 MiB at 78000000, total cma pages:4096
  249. [ 0.000000@0] linux,ppmgr: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
  250. [ 0.000000@0] linux,codec_mm_cma: 0x0000000067800000 - 0x0000000073800000 (192 MiB)
  251. [ 0.000000@0] cma: Reserved 192 MiB at 67800000, total cma pages:53248
  252. [ 0.000000@0] linux,picdec: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
  253. [ 0.000000@0] Reserved memory: incorrect alignment of CMA region
  254. [ 0.000000@0] linux,codec_mm_reserved: 0x0000000073f00000 - 0x0000000078000000 (65 MiB)
  255. [ 0.000000@0] fdt Reserved memory total: 403 MiB
  256. [ 0.000000@0] cma: Reserved 8 MiB at 67000000, total cma pages:55296
  257. [ 0.000000@0] psci: probing function IDs from device-tree
  258. [ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc07926c000 s17536 r8192 d23424 u49152
  259. [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 499800
  260. [ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=permissive logo=osd1,loaded,0x3d800000,576cvbs maxcpus=8 vout=576cvbs,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 pq= androidboot.firstboot=0 jtag=apee androidboot.hardware=amlogic androidboot.slot_suffix=_a console=tty0 systemd.show_status=auto ssh
  261. [ 0.000000@0] logo: osd1
  262. [ 0.000000@0] logo: loaded
  263. [ 0.000000@0] logo: 0x3d800000
  264. [ 0.000000@0] logo: 576cvbs
  265. [ 0.000000@0] vout_serve: 576cvbs
  266. [ 0.000000@0] vout_serve: en: 1
  267. [ 0.000000@0] vout_serve: set_vout_init_vmode: 576cvbs
  268. [ 0.000000@0] vout_serve: 576cvbs
  269. [ 0.000000@0] vout_serve: enable: 1
  270. [ 0.000000@0] logo: get hdmimode: 1080p60hz
  271. [ 0.000000@0] logo: get cvbsmode: 576cvbs
  272. [ 0.000000@0] tv_vout: cvbs performance line = 0
  273. [ 0.000000@0] [amvecm] pq string error !!!
  274. [ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
  275. [ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
  276. [ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
  277. [ 0.000000@0] Memory: 1590440K/2043904K available (7065K kernel code, 832K rwdata, 2644K rodata, 913K init, 2908K bss, 453464K reserved)
  278. [ 0.000000@0] Virtual kernel memory layout:
  279. [ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
  280. [ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff8042bbd800 ( 43 MB)
  281. [ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
  282. [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07f100000 ( 2033 MB)
  283. [ 0.000000@0] .init : 0xffffffc0019fd000 - 0xffffffc001ae1480 ( 914 kB)
  284. [ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc0019fc774 ( 9714 kB)
  285. [ 0.000000@0] .data : 0xffffffc001ae2000 - 0xffffffc001bb21d8 ( 833 kB)
  286. [ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x019fbfff]
  287. [ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1
  288. [ 0.000000@0] arch_multi_cluster:1
  289. [ 0.000000@0] Hierarchical RCU implementation.
  290. [ 0.000000@0] RCU debugfs-based tracing is enabled.
  291. [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
  292. [ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
  293. [ 0.000005@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
  294. [ 0.008247@0] meson_bc_timer: mclk->mux_reg =ffffff8000014990,mclk->reg =ffffff8000016994
  295. [ 0.016780@0] Console: colour dummy device 80x25
  296. [ 0.021087@0] console [tty0] enabled
  297. [ 0.024672@0] bootconsole [earlycon0] disabled
  298. [ 0.030650@0] allocated 8388608 bytes of page_cgroup
  299. [ 0.030660@0] please try 'cgroup_disable=memory' option if you don't want memory cgroups
  300. [ 0.030684@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
  301. [ 0.030701@0] pid_max: default: 32768 minimum: 301
  302. [ 0.030825@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
  303. [ 0.030838@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
  304. [ 0.036228@0] Initializing cgroup subsys memory
  305. [ 0.036262@0] Initializing cgroup subsys devices
  306. [ 0.036272@0] Initializing cgroup subsys freezer
  307. [ 0.036282@0] Initializing cgroup subsys blkio
  308. [ 0.036290@0] Initializing cgroup subsys net_prio
  309. [ 0.036336@0] ftrace: allocating 23918 entries in 94 pages
  310. [ 0.064628@0] /cpus/cpu@0: Missing clock-frequency property
  311. [ 0.064651@0] /cpus/cpu@1: Missing clock-frequency property
  312. [ 0.064662@0] /cpus/cpu@2: Missing clock-frequency property
  313. [ 0.064674@0] /cpus/cpu@3: Missing clock-frequency property
  314. [ 0.064686@0] /cpus/cpu@100: Missing clock-frequency property
  315. [ 0.064698@0] /cpus/cpu@101: Missing clock-frequency property
  316. [ 0.064711@0] /cpus/cpu@102: Missing clock-frequency property
  317. [ 0.064724@0] /cpus/cpu@103: Missing clock-frequency property
  318. [ 0.066220@0] Meson chip version = RevA (22:A - 82:0)
  319. [ 0.066735@1] CPU1: Booted secondary processor
  320. [ 0.067130@2] CPU2: Booted secondary processor
  321. [ 0.067500@3] CPU3: Booted secondary processor
  322. [ 0.067871@4] CPU4: Booted secondary processor
  323. [ 0.068262@5] CPU5: Booted secondary processor
  324. [ 0.068625@6] CPU6: Booted secondary processor
  325. [ 0.068988@7] CPU7: Booted secondary processor
  326. [ 0.069069@0] Brought up 8 CPUs
  327. [ 0.069129@0] SMP: Total of 8 processors activated.
  328. [ 0.069628@0] devtmpfs: initialized
  329. [ 0.075845@2] sched: registering cpufreq notifiers for scale-invariant loads
  330. [ 0.075885@2] instabooting: 0
  331. [ 0.083141@0] cma: cma_init_reserved_areas, use_cma_first:1
  332. [ 0.083216@0] pinctrl core: initialized pinctrl subsystem
  333. [ 0.083760@2] regulator-dummy: no parameters
  334. [ 0.084484@2] NET: Registered protocol family 16
  335. [ 0.085718@2] ramoops: using module parameters
  336. [ 0.086185@2] pstore: Registered ramoops as persistent store backend
  337. [ 0.086204@2] ramoops: attached 0x100000@0x7300000, ecc: 0/0
  338. [ 0.086957@2] aml_vdac_init: module init
  339. [ 0.087096@0] register canvas platform driver
  340. [ 0.087172@3] register rdma platform driver
  341. [ 0.088265@3] vdso: 2 pages (1 code, 1 data) at base ffffffc001aec000
  342. [ 0.088643@3] DMA: preallocated 256 KiB pool for atomic allocations
  343. [ 0.089499@3] software IO TLB [mem 0x62800000-0x62c00000] (4MB) mapped at [ffffffc062800000-ffffffc062bfffff]
  344. [ 0.089890@3] aml_i2c version: 20140813
  345. [ 0.090108@2] i2c-core: driver [pmu4] using legacy resume method
  346. [ 0.090197@3] codec_mm:codec_mm_module_init
  347. [ 0.090538@0] gxbb_mpll_clk: register mpll_clk_out0 success done
  348. [ 0.090552@0] gxbb_mpll_clk: register mpll_clk_out1 success done
  349. [ 0.090565@0] gxbb_mpll_clk: register mpll_clk_out2 success done
  350. [ 0.090771@0] clk_sys: register PLL sys_pll success done
  351. [ 0.090789@0] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
  352. [ 0.090799@0] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
  353. [ 0.090809@0] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
  354. [ 0.090818@0] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
  355. [ 0.090827@0] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
  356. [ 0.090836@0] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
  357. [ 0.090845@0] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
  358. [ 0.090854@0] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
  359. [ 0.090862@0] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
  360. [ 0.090895@0] gxl_clk: clock initialization complete
  361. [ 0.091100@0] clkmsr: Gxl msr_clk_reg0=ffffff800003c75c,msr_clk_reg2=ffffff800003e764
  362. [ 0.093345@2] aml_iomap: amlogic iomap probe done
  363. [ 0.093867@2] pinmux-gxl c1109880.pinmux: Init pinux probe!
  364. [ 0.094702@2] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
  365. [ 0.095474@3] aml-i2c c1108500.i2c: add adapter aml_i2c_adap1(ffffffc0624560e0)
  366. [ 0.096442@2] aml-i2c c11087c0.i2c: add adapter aml_i2c_adap2(ffffffc0624568e0)
  367. [ 0.096724@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xc0)
  368. [ 0.096750@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xc0)
  369. [ 0.096899@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xc0)
  370. [ 0.096921@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xc0)
  371. [ 0.099173@0] dvfs [scpi_dvfs_get_opps] - buf.opp[0].freq_hz = 100000000
  372. [ 0.099185@0] dvfs [scpi_dvfs_get_opps] - buf.opp[1].freq_hz = 250000000
  373. [ 0.099195@0] dvfs [scpi_dvfs_get_opps] - buf.opp[2].freq_hz = 500000000
  374. [ 0.099205@0] dvfs [scpi_dvfs_get_opps] - buf.opp[3].freq_hz = 667000000
  375. [ 0.099214@0] dvfs [scpi_dvfs_get_opps] - buf.opp[4].freq_hz = 1000000000
  376. [ 0.099223@0] dvfs [scpi_dvfs_get_opps] - buf.opp[5].freq_hz = 1200000000
  377. [ 0.099232@0] dvfs [scpi_dvfs_get_opps] - buf.opp[6].freq_hz = 1512000000
  378. [ 0.099242@0] dvfs [scpi_dvfs_get_opps] - new count 7, max_freq 1512000000
  379. [ 0.101414@0] dvfs [scpi_dvfs_get_opps] - buf.opp[0].freq_hz = 100000000
  380. [ 0.101425@0] dvfs [scpi_dvfs_get_opps] - buf.opp[1].freq_hz = 250000000
  381. [ 0.101435@0] dvfs [scpi_dvfs_get_opps] - buf.opp[2].freq_hz = 500000000
  382. [ 0.101444@0] dvfs [scpi_dvfs_get_opps] - buf.opp[3].freq_hz = 667000000
  383. [ 0.101454@0] dvfs [scpi_dvfs_get_opps] - buf.opp[4].freq_hz = 1000000000
  384. [ 0.101463@0] dvfs [scpi_dvfs_get_opps] - new count 5, max_freq 1000000000
  385. [ 0.103365@0] codec_mm has 2 memory regions
  386. [ 0.103413@0] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
  387. [ 0.103432@0] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
  388. [ 0.103525@2] codec_mm has 2 memory regions
  389. [ 0.103545@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
  390. [ 0.103561@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
  391. [ 0.105426@3] vpu: driver version: v03
  392. [ 0.105468@3] vpu: load vpu_clk: 666667000Hz(7)
  393. [ 0.105550@0] vpu: vpu_probe OK
  394. [ 0.106710@2] tv_vout: tvout_probe
  395. [ 0.106729@2] tv_vout: chrdev devno 265289728 for disp
  396. [ 0.106737@2] vout_notify: vout_register_server
  397. [ 0.106746@2] tv_vout: register tv module server ok
  398. [ 0.106996@0] tv_vout: create cdev tv
  399. [ 0.107009@0] tv_vout: tvout_probe OK
  400. [ 0.107550@2] canvas_probe reg=00000000c8838000,size=400
  401. [ 0.107582@2] canvas maped reg_base =ffffff800009e000
  402. [ 0.111244@3] rdma_probe
  403. [ 0.316941@3] bio: create slab <bio-0> at 0
  404. [ 0.317833@3] SCSI subsystem initialized
  405. [ 0.318336@3] usbcore: registered new interface driver usbfs
  406. [ 0.318431@0] usbcore: registered new interface driver hub
  407. [ 0.318553@2] usbcore: registered new device driver usb
  408. [ 0.319243@2] i2c-gpio i2c_gpio.39: using pins 172 (SDA) and 173 (SCL)
  409. [ 0.319416@0] pps_core: LinuxPPS API ver. 1 registered
  410. [ 0.319427@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  411. [ 0.319496@2] PTP clock support registered
  412. [ 0.319987@3] hdmitx: system: amhdmitx_init
  413. [ 0.319998@3] hdmitx: system: Ver: 2014May6
  414. [ 0.320179@3] hdmitx: system: amhdmitx_probe
  415. [ 0.320495@2] hdmitx: system: not find match init-data
  416. [ 0.320511@2] hdmitx hpd irq = 89
  417. [ 0.321043@2] hdmitx20: Mapped PHY: 0xc0800000
  418. [ 0.321061@2] hdmitx20: Mapped PHY: 0xc1104400
  419. [ 0.321085@2] hdmitx20: Mapped PHY: 0xc8100000
  420. [ 0.321095@2] hdmitx20: Mapped PHY: 0xc8834000
  421. [ 0.321104@2] hdmitx20: Mapped PHY: 0xc883a000
  422. [ 0.321112@2] hdmitx20: Mapped PHY: 0xc883c000
  423. [ 0.321124@2] hdmitx20: Mapped PHY: 0xd0100000
  424. [ 0.321134@2] hdmitx20: Mapped PHY: 0xda83a000
  425. [ 0.321393@2] avmute set to 1
  426. [ 0.321792@3] tv_vout: tv_set_current_vmode[919]fps_target_mode=7
  427. [ 0.321807@3] tv_vout: mode is 7,sync_duration_den=1,sync_duration_num=50
  428. [ 0.321824@3] tv_vout: already display in uboot
  429. [ 0.321832@3] vout_serve: vinfo mode is: 576cvbs
  430. [ 0.321840@3] vout_serve: init mode 576cvbs
  431. [ 0.322077@2] vout_serve: create_vout_fops OK
  432. [ 0.322088@2] vout_serve: create vout attribute OK
  433. [ 0.322096@2] vout_serve: meson_vout_probe OK
  434. [ 0.322253@2] logo: logo_init
  435. [ 0.322495@2] osd_rdma: osd_rdma_init: rdma_table p=0x67041000,op=0x67041000 , v=0xffffff80000b9000
  436. [ 0.322528@2] rdma_register, rdma_table_addr ffffff80000c9000 rdma_table_addr_phy 67042000 reg_buf ffffffc0626cc000
  437. [ 0.322542@2] rdma_register success, handle 1 table_size 4096
  438. [ 0.322551@2] osd_rdma: osd_rdma_init:osd reset rdma handle = 1.
  439. [ 0.322588@2] rdma_register, rdma_table_addr ffffff80000d9000 rdma_table_addr_phy 67043000 reg_buf ffffffc0626cd000
  440. [ 0.322601@2] rdma_register success, handle 2 table_size 4096
  441. [ 0.322610@2] osd_rdma: osd_rdma_init:osd rdma handle = 2.
  442. [ 0.322993@0] Advanced Linux Sound Architecture Driver Initialized.
  443. [ 0.325115@0] Switched to clocksource arch_sys_counter
  444. [ 0.334035@0] FS-Cache: Loaded
  445. [ 0.342505@2] NET: Registered protocol family 2
  446. [ 0.342952@2] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
  447. [ 0.343078@2] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
  448. [ 0.343299@2] TCP: Hash tables configured (established 16384 bind 16384)
  449. [ 0.343369@2] TCP: reno registered
  450. [ 0.343384@2] UDP hash table entries: 1024 (order: 3, 32768 bytes)
  451. [ 0.343431@2] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
  452. [ 0.343668@2] NET: Registered protocol family 1
  453. [ 0.344133@0] pwm: probe ok
  454. [ 0.344394@0] wifi: power_on_pin_OD = 0;
  455. [ 0.344410@0] aml_wifi wifi.34: [wifi_dev_probe] no power_on_pin2
  456. [ 0.344444@0] aml_wifi wifi.34: [pwm_double_channel_conf_dt] pwm phandle val=32;pwm-channel1=4;pwm-channel2=12
  457. [ 0.344459@0] aml_wifi wifi.34: [pwm_double_channel_conf_dt] pwm_config1[0] = 30541
  458. [ 0.344472@0] aml_wifi wifi.34: [pwm_double_channel_conf_dt] pwm_config2[0] = 30518
  459. [ 0.344484@0] aml_wifi wifi.34: [pwm_double_channel_conf_dt] pwm_config1[1] = 15270
  460. [ 0.344497@0] aml_wifi wifi.34: [pwm_double_channel_conf_dt] pwm_config2[1] = 15259
  461. [ 0.344510@0] aml_wifi wifi.34: [pwm_double_channel_conf_dt] pwm_config1[2] = 6
  462. [ 0.344522@0] aml_wifi wifi.34: [pwm_double_channel_conf_dt] pwm_config2[2] = 9
  463. [ 0.344534@0] aml_wifi wifi.34: [pwm_double_channel_conf_dt] wifi pwm dt ok
  464. [ 0.344559@0] aml_wifi wifi.34: [pwm_double_channel_conf] wifi pwm conf ok
  465. [ 0.344613@0] aml_wifi wifi.34: [wifi_dev_probe] dhd_static_buf setup
  466. [ 0.344691@0] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem: WIFI MEM Allocated
  467. [ 0.344704@0] aml_wifi wifi.34: [wifi_dev_probe] interrupt_pin=241
  468. [ 0.344715@0] aml_wifi wifi.34: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
  469. [ 0.344727@0] aml_wifi wifi.34: [wifi_dev_probe] power_on_pin=240
  470. [ 0.344737@0] aml_wifi wifi.34: [wifi_dev_probe] clock_32k_pin=0
  471. [ 0.344998@2] aml_wifi wifi.34: [wifi_setup_dt] wifi_setup_dt
  472. [ 0.345130@2] aml_wifi wifi.34: [wifi_setup_dt] interrupt_pin(241)
  473. [ 0.345150@2] aml_wifi wifi.34: [wifi_setup_dt] power_on_pin(240)
  474. [ 0.345354@3] Unpacking initramfs...
  475. [ 0.355581@3] Freeing initrd memory: 4208K (ffffffc073aa8000 - ffffffc073ec4000)
  476. [ 0.358278@2] futex hash table entries: 2048 (order: 5, 131072 bytes)
  477. [ 0.367709@3] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  478. [ 0.368176@3] msgmni has been set to 3546
  479. [ 0.369233@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
  480. [ 0.369336@3] io scheduler noop registered (default)
  481. [ 0.369347@3] io scheduler deadline registered
  482. [ 0.369375@3] io scheduler cfq registered
  483. [ 0.370192@0] meson-rng c8834000.rng: hwrng registered
  484. [ 0.373581@0] loop: module loaded
  485. [ 0.375389@2] tun: Universal TUN/TAP device driver, 1.6
  486. [ 0.375410@2] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  487. [ 0.500007@3] libphy: stmmac: probed
  488. [ 0.500030@3] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
  489. [ 0.500041@3] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
  490. [ 0.500441@0] PPP generic driver version 2.4.2
  491. [ 0.500705@3] NET: Registered protocol family 24
  492. [ 0.500824@0] usbcore: registered new interface driver smsc95xx
  493. [ 0.501155@3] platform c9000000.dwc3: Driver dwc3 requests probe deferral
  494. [ 0.501275@3] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  495. [ 0.501299@3] ehci-h20ahb: H20AHB-EHCI Host Controller driver
  496. [ 0.501505@0] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  497. [ 0.501798@3] usbcore: registered new interface driver usb-storage
  498. [ 0.501998@3] usbcore: registered new interface driver usbserial
  499. [ 0.502085@3] usbcore: registered new interface driver usbserial_generic
  500. [ 0.502168@0] usbserial: USB Serial support registered for generic
  501. [ 0.502246@1] usbcore: registered new interface driver pl2303
  502. [ 0.502324@3] usbserial: USB Serial support registered for pl2303
  503. [ 0.502832@3] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff80000fe000
  504. [ 0.503041@3] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
  505. [ 0.503103@3] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff800010a080
  506. [ 0.503409@1] mousedev: PS/2 mouse device common for all mice
  507. [ 0.506599@0] rtc-aml_hym8563 2-0051: rtc core: registered rtc_hym8563 as rtc0
  508. [ 0.506787@3] i2c /dev entries driver
  509. [ 0.507799@1] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
  510. [ 0.510052@0] cpu cpu4: bL_cpufreq_init: CPU 4 initialized
  511. [ 0.511317@0] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
  512. [ 0.511924@3] ledtrig-cpu: registered to indicate activity on CPUs
  513. [ 0.512069@1] hidraw: raw HID events driver (C) Jiri Kosina
  514. [ 0.514103@3] usbcore: registered new interface driver usbhid
  515. [ 0.514122@3] usbhid: USB HID core driver
  516. [ 0.514302@0] ashmem: initialized
  517. [ 0.514654@1] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff800010c4c0
  518. [ 0.514686@1] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
  519. [ 0.514706@1] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
  520. [ 2.182990@0] console [ttyS0] enabled
  521. [ 2.187006@0] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff800010e4c0
  522. [ 2.193686@0] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
  523. [ 2.203521@3] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
  524. [ 2.212923@3] meson-gpu-clkgen: probe of c883c000.gpu_clk failed with error -16
  525. [ 2.220621@3] hdmitx: system: hdmitx_hdcp_init
  526. [ 2.224967@3] secmon has 1 memory regions
  527. [ 2.228567@3] secmon: share in base: 0xffffff800011a000, share out base: 0xffffff800011c000
  528. [ 2.236812@3] secmon secmon.4: assigned reserved memory node linux,secmon ok
  529. [ 2.243777@3] secmon: probe done
  530. [ 2.247529@3] storage: storage in base: 0xffffff8001800000
  531. [ 2.252404@3] storage: storage out base: 0xffffff8001880000
  532. [ 2.257952@3] storage: storage block base: 0xffffff8001900000
  533. [ 2.263615@3] storage: probe done!
  534. [ 2.267783@3] aml_sd_emmc_probe: line 3594
  535. [ 2.271036@3] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
  536. [ 2.281165@3] aml_sd_emmc_reg_init 1149
  537. [ 2.284285@3] get property: ocr_avail, value:0x00200080
  538. [ 2.290717@3] get property: f_min, value:300000
  539. [ 2.296847@3] get property: f_max, value:100000000
  540. [ 2.303208@3] get property: max_req_size, value:0x00020000
  541. [ 2.309693@3] get property: pinname, str:emmc
  542. [ 2.315466@3] get property: card_type, value:1
  543. [ 2.321166@3] get property: gpio_dat3, str:
  544. [ 2.326592@3] get property: hw_reset, str:
  545. [ 2.332054@3] emmc:pdata->caps = c0000d47
  546. [ 2.335994@3] emmc:pdata->caps2 = 18060
  547. [ 2.339777@3] emmc:pdata->pm_caps = 0
  548. [ 2.343412@3] storage 1, boot 1
  549. [ 2.346518@3] get_storage_dev return 1
  550. [ 2.385019@0] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
  551. [ 2.385235@0] aml_sd_emmc_probe: line 3594
  552. [ 2.389660@0] aml_sd_emmc_reg_init 1149
  553. [ 2.393185@0] get property: ocr_avail, value:0x00200080
  554. [ 2.399617@0] get property: f_min, value:400000
  555. [ 2.405761@0] get property: f_max, value:100000000
  556. [ 2.412036@0] get property: max_req_size, value:0x00020000
  557. [ 2.418508@0] get property: irq_in, value:3
  558. [ 2.424212@0] get property: irq_out, value:5
  559. [ 2.429973@0] get property: gpio_cd, str:
  560. [ 2.435328@0] get property: pinname, str:sd
  561. [ 2.440946@0] get property: jtag_pin, str:
  562. [ 2.446463@0] get property: card_type, value:5
  563. [ 2.452055@0] get property: card_in_delay, value:400
  564. [ 2.457931@0] get property: gpio_dat3, str:
  565. [ 2.463388@0] sd:pdata->caps = 7
  566. [ 2.466625@0] sd:pdata->caps2 = 0
  567. [ 2.469823@0] sd:pdata->pm_caps = 0
  568. [ 2.505215@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
  569. [ 2.505440@3] aml_sd_emmc_probe: line 3594
  570. [ 2.509868@3] aml_sd_emmc_reg_init 1149
  571. [ 2.513308@3] get property: ocr_avail, value:0x00200080
  572. [ 2.519747@3] get property: f_min, value:400000
  573. [ 2.525858@3] get property: f_max, value:200000000
  574. [ 2.532234@3] get property: max_req_size, value:0x00020000
  575. [ 2.538713@3] get property: pinname, str:sdio
  576. [ 2.539184@2] emmc: BKOPS_EN bit is not set
  577. [ 2.545618@2] emmc: trying cali 0-th time(s)
  578. [ 2.549409@2] emmc: delay[0]= 1600 padding= 2, bidx=1
  579. [ 2.549413@2] emmc: delay[1]= 1800 padding= 1, bidx=1
  580. [ 2.549417@2] emmc: delay[2]= 1600 padding= 2, bidx=1
  581. [ 2.549421@2] emmc: delay[3]= 1800 padding= 1, bidx=1
  582. [ 2.549425@2] emmc: delay[4]= 1800 padding= 1, bidx=1
  583. [ 2.549428@2] emmc: delay[5]= 1800 padding= 1, bidx=1
  584. [ 2.549432@2] emmc: delay[6]= 1600 padding= 2, bidx=1
  585. [ 2.549436@2] emmc: delay[7]= 1800 padding= 1, bidx=1
  586. [ 2.549440@2] emmc: calibration result @ 0: max(1800), min(1600)
  587. [ 2.549444@2] emmc: line_delay =0x1000101, max_cal_result =1800
  588. [ 2.549447@2] emmc: base_index_max 1, base_index_min 1
  589. [ 2.549454@2] emmc: clk 100000000 SDR mode tuning start
  590. [ 2.549971@2] emmc: rx_tuning_result[1] = 10
  591. [ 2.550436@2] emmc: rx_tuning_result[2] = 10
  592. [ 2.550902@2] emmc: rx_tuning_result[3] = 10
  593. [ 2.551368@2] emmc: rx_tuning_result[4] = 10
  594. [ 2.551832@2] emmc: rx_tuning_result[5] = 10
  595. [ 2.552296@2] emmc: rx_tuning_result[6] = 10
  596. [ 2.552760@2] emmc: rx_tuning_result[7] = 10
  597. [ 2.553223@2] emmc: rx_tuning_result[8] = 10
  598. [ 2.553688@2] emmc: rx_tuning_result[9] = 10
  599. [ 2.553692@2] emmc: best_win_start =1, best_win_size =9
  600. [ 2.553697@2] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x52000
  601. [ 2.553702@2] emmc: gclock =0x100024a, gdelay=0x1000101, gadjust=0x52000
  602. [ 2.553884@2] emmc: support driver strength type 1
  603. [ 2.553972@2] emmc: try set sd/emmc to DDR mode
  604. [ 2.553977@2] emmc: try set sd/emmc to DDR mode
  605. [ 2.554149@2] emmc: new HS400 MMC card at address 0001
  606. [ 2.554829@2] emmc: clock 100000000, 8-bit-bus-width
  607. [ 2.554829@2]
  608. [ 2.554829@2] mmcblk0: emmc:0001 AJNB4R 14.5 GiB
  609. [ 2.555077@2] mmcblk0boot0: emmc:0001 AJNB4R partition 1 4.00 MiB
  610. [ 2.555299@2] mmcblk0boot1: emmc:0001 AJNB4R partition 2 4.00 MiB
  611. [ 2.555535@2] mmcblk0rpmb: emmc:0001 AJNB4R partition 3 4.00 MiB
  612. [ 2.556522@1] mmcblk0: unknown partition table
  613. [ 2.557288@2] [mmc_read_partition_tbl] mmc read partition OK!
  614. [ 2.557290@2] add_emmc_partition
  615. [ 2.557611@1] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
  616. [ 2.557853@2] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
  617. [ 2.558075@1] [mmcblk0p03] cache offset 0x000006c00000, size 0x000020000000
  618. [ 2.558298@2] [mmcblk0p04] env offset 0x000027400000, size 0x000000800000
  619. [ 2.558525@1] [mmcblk0p05] logo offset 0x000028400000, size 0x000002000000
  620. [ 2.558752@2] [mmcblk0p06] recovery offset 0x00002ac00000, size 0x000002000000
  621. [ 2.558968@1] [mmcblk0p07] rsv offset 0x00002d400000, size 0x000000800000
  622. [ 2.559188@2] [mmcblk0p08] tee offset 0x00002e400000, size 0x000000800000
  623. [ 2.559424@1] [mmcblk0p09] crypt offset 0x00002f400000, size 0x000002000000
  624. [ 2.559653@2] [mmcblk0p10] misc offset 0x000031c00000, size 0x000002000000
  625. [ 2.559935@1] [mmcblk0p11] instaboot offset 0x000034400000, size 0x000020000000
  626. [ 2.560180@2] [mmcblk0p12] boot offset 0x000054c00000, size 0x000002000000
  627. [ 2.560411@1] [mmcblk0p13] system offset 0x000057400000, size 0x000040000000
  628. [ 2.560645@2] [mmcblk0p14] data offset 0x000097c00000, size 0x00030c200000
  629. [ 2.560684@2] card key: card_blk_probe.
  630. [ 2.560690@2] emmc_key_init:527 emmc key lba_start:0x12020,lba_end:0x12220
  631. [ 2.560694@2] emmc key: emmc_key_init:552 ok.
  632. [ 2.563436@2] amlmmc_dtb_init: register dtb chardev
  633. [ 2.563437@2] calc e2e48a5f, store e2e48a5f
  634. [ 2.565939@2] calc e2e48a5f, store e2e48a5f
  635. [ 2.565941@2] total valid 2
  636. [ 2.566580@1] amlmmc_dtb_init: register dtb chardev OK
  637. [ 2.566581@1] Exit aml_emmc_partition_ops OK.
  638. [ 2.567991@2] mmcblk0boot1: unknown partition table
  639. [ 2.569123@2] mmcblk0boot0: unknown partition table
  640. [ 2.569448@1] clear_emmc_wait_flag
  641. [ 2.904161@3] get property: card_type, value:3
  642. [ 2.905351@4] [aml_is_card_insert] card OUT
  643. [ 2.914006@3] sdio:pdata->caps = 78107
  644. [ 2.917689@3] sdio:pdata->caps2 = 0
  645. [ 2.921135@3] sdio:pdata->pm_caps = 1
  646. [ 2.965024@2] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
  647. [ 2.965565@2] ion_dev has 1 memory regions
  648. [ 2.996955@0] fb: osd_init_module
  649. [ 2.997123@0] fb: viu vsync irq: 35
  650. [ 2.998107@0] fb: failed to init reserved memory
  651. [ 3.002724@0] fb: osd_probe vinfo:ffffffc001b498a0
  652. [ 3.007444@0] fb: init fbdev bpp is:32
  653. [ 3.011721@0] fb: set osd0 reverse as NONE
  654. [ 3.019661@0] fb: osd probe OK
  655. [ 3.019889@0] ge2d: ge2d_init_module
  656. [ 3.021742@0] ge2d: ge2d_dev major:241
  657. [ 3.025842@0] ge2d: ge2d clock is 400 MHZ
  658. [ 3.029414@0] ge2d: ge2d: pdev=ffffffc06246aa00, irq=182, rstc=0xffffffc061cea880, clk=ffffffc062418700
  659. [ 3.038775@0] ge2d: mapped phy: 0xd0160000
  660. [ 3.042824@0] ge2d: ge2d start monitor
  661. [ 3.046672@1] ge2d: ge2d workqueue monitor start
  662. [ 3.047196@0] codec:Amlogic A/V streaming port init
  663. [ 3.049829@2] codec:get gate demux control ok ffffffc0626dae00
  664. [ 3.049837@2] codec:get gate parser_top control ok ffffffc0626daa80
  665. [ 3.049845@2] codec:get gate vpu_intr control ok ffffffc0626da680
  666. [ 3.049855@2] codec:get gate vdec control ok ffffffc0626da3c0
  667. [ 3.050952@2] codec:[tsync_pcr_init]init success.
  668. [ 3.051144@2] codec:amvideocap_probe,amvideocap
  669. [ 3.051147@2] codec:use cma buf.
  670. [ 3.054592@2] codec:vdec_request_irq ffffffc001570b48, vsync
  671. [ 3.054902@0] codec:create_ge2d_work_queue video task ok
  672. [ 3.103073@2] rdma_register, rdma_table_addr ffffff8000256000 rdma_table_addr_phy 67050000 reg_buf ffffffc061d88000
  673. [ 3.113176@2] rdma_register success, handle 3 table_size 32768
  674. [ 3.118949@2] video_rdma:rdma_init video rdma handle = 3.
  675. [ 3.124292@2] codec:used fix clk for vdec clk source!
  676. [ 3.129305@2] codec:register clk_set_setting cpu[34]
  677. [ 3.135111@0] DI: di_module_init ok.
  678. [ 3.137748@0] DI: di_module_init: major 237
  679. [ 3.142285@1] DI: di_probe
  680. [ 3.144800@0] deinterlace has 1 memory regions
  681. [ 3.149037@0] deinterlace deinterlace.26: assigned reserved memory node linux,di ok
  682. [ 3.156561@0] DI-di_probe: get flag_cma error.
  683. [ 3.161076@1] di_irq:78,timerc_irq:38
  684. [ 3.164696@1] rdma_register, rdma_table_addr ffffff800017b000 rdma_table_addr_phy 6704a000 reg_buf ffffffc061db4000
  685. [ 3.174938@1] rdma_register success, handle 4 table_size 8192
  686. [ 3.180614@1] DI: di_probe allocate rdma channel 4.
  687. [ 3.185444@1] DI: DI hw version 2.
  688. [ 3.188810@1] 0x000000db:Y=db,U=0,V=0
  689. [ 3.192424@1] 0x000000dc:Y=dc,U=0,V=0
  690. [ 3.196052@1] 0x000000dd:Y=dd,U=0,V=0
  691. [ 3.199669@1] 0x000000de:Y=de,U=0,V=0
  692. [ 3.203292@1] 0x000000df:Y=df,U=0,V=0
  693. [ 3.206919@1] 0x000000e0:Y=e0,U=0,V=0
  694. [ 3.210537@1] 0x000000e1:Y=e1,U=0,V=0
  695. [ 3.214159@1] 0x000000e2:Y=e2,U=0,V=0
  696. [ 3.217786@1] 0x000000e3:Y=e3,U=0,V=0
  697. [ 3.221404@1] 0x000000f0:Y=f0,U=0,V=0
  698. [ 3.225033@1] 0x000000f1:Y=f1,U=0,V=0
  699. [ 3.228649@1] 0x000000f2:Y=f2,U=0,V=0
  700. [ 3.232272@1] 0x000000f3:Y=f3,U=0,V=0
  701. [ 3.235902@1] 0x000000f4:Y=f4,U=0,V=0
  702. [ 3.239517@1] 0x000000f5:Y=f5,U=0,V=0
  703. [ 3.243139@1] 0x000000f6:Y=f6,U=0,V=0
  704. [ 3.246767@1] 0x000000f7:Y=f7,U=0,V=0
  705. [ 3.250384@1] 0x000000f8:Y=f8,U=0,V=0
  706. [ 3.254006@1] 0x000000f9:Y=f9,U=0,V=0
  707. [ 3.257633@1] 0x000000fa:Y=fa,U=0,V=0
  708. [ 3.261251@1] 0x000000fb:Y=fb,U=0,V=0
  709. [ 3.264874@1] 0x000000fc:Y=fc,U=0,V=0
  710. [ 3.268952@1] efusekeynum: 4
  711. [ 3.271350@1] efusekeyname: mac offset: 0 size: 6
  712. [ 3.277755@1] efusekeyname: mac_bt offset: 6 size: 6
  713. [ 3.284112@1] efusekeyname: mac_wifi offset: 12 size: 6
  714. [ 3.290510@1] efusekeyname: usid offset: 18 size: 16
  715. [ 3.297172@0] efuse efuse.10: probe OK!
  716. [ 3.301045@0] key unify config unifykey-num is 14
  717. [ 3.305386@0] key unify fact unifykey-num is 14
  718. [ 3.305484@5] [aml_is_card_insert] card OUT
  719. [ 3.313953@0] aml_unifykeys_probe:1280=============unifykey_devno:eb00000
  720. [ 3.321034@0] 6unifykey: device unifykeys created ok
  721. [ 3.325807@0] 6aml_unifykeys_init done!
  722. [ 3.329562@0] PPMGRDRV: warn: ppmgr module init func called
  723. [ 3.335218@0] PPMGRDRV: err: ppmgr_driver_probe called
  724. [ 3.340220@0] ppmgr has 1 memory regions
  725. [ 3.344082@0] PPMGRDRV: info: ppmgr_dev major:234
  726. [ 3.349151@0] PPMGRDRV: info: ppmgr_probe done
  727. [ 3.353597@1] amlogic rfkill init
  728. [ 3.356555@1] enter bt_probe of_node
  729. [ 3.359936@1] not get gpio_en
  730. [ 3.362855@1] power on valid level is high
  731. [ 3.366765@1] bt: power_on_pin_OD = 0;
  732. [ 3.786475@0] audio_dsp: [dsp]register dsp to char divece(257)
  733. [ 3.793968@1] amaudio: amaudio: driver amaudio succuess!
  734. [ 3.799117@0] [RX]-hdmirx: hdmirx_init.
  735. [ 3.799299@0] ESM HLD: Initializing...
  736. [ 3.801579@0] ESM HLD: Registering device range 'esm_rx'...
  737. [ 3.806982@0] ESM HLD: Device range 'esm_rx' has been registered.
  738. [ 3.812830@0] ESM HLD: Creating class /sys/class/elliptic_rx...
  739. [ 3.819957@0] ESM HLD: The class /sys/class/elliptic_rx has been created.
  740. [ 3.825746@0] ESM HLD: Creating device 'esm_rx'...
  741. [ 3.831496@0] ESM HLD: Device 'esm_rx' has been created.
  742. [ 3.835529@0] ESM HLD: Done initializing the HLD driver.
  743. [ 3.840936@0] module init
  744. [ 3.844143@0]
  745. [ 3.844143@0] VECM probe start
  746. [ 3.848780@1] dolby_vision_init_receiver(dvel)
  747. [ 3.852407@1] dolby_vision_init_receiver: dvel
  748. [ 3.856848@1] aml_vecm_probe: ok
  749. [ 3.861296@0] saradc c1108680.saradc: initialized by BL30
  750. [ 3.865400@0] saradc c1108680.saradc: calibration start:
  751. [ 3.870647@0] saradc c1108680.saradc: nominal=0, value=6
  752. [ 3.875915@0] saradc c1108680.saradc: nominal=256, value=231
  753. [ 3.881619@0] saradc c1108680.saradc: nominal=512, value=461
  754. [ 3.887134@0] saradc c1108680.saradc: nominal=768, value=691
  755. [ 3.892725@0] saradc c1108680.saradc: nominal=1023, value=919
  756. [ 3.898382@0] saradc c1108680.saradc: calibration end: coef=4559
  757. [ 3.905608@3] remote: Driver init
  758. [ 3.908373@3] gpio-key gpio_keypad.49: gpio_key: 0 name(power) pin()
  759. [ 3.913901@3] gpio-key gpio_keypad.49: amlogic_gpio_name_map_num pin 0!::
  760. [ 3.920693@3] gpio-key gpio_keypad.49: gpio_key: 0 power(147)
  761. [ 3.926411@3] gpio-key gpio_keypad.49: start setup_timer
  762. [ 3.931583@3] gpio-key gpio_keypad.49: power key(116) registed.
  763. [ 3.937873@1] input: gpio_keypad as /devices/gpio_keypad.49/input/input0
  764. [ 3.944431@2] gpio-key gpio_keypad.49: gpio keypad register input device completed.
  765. [ 3.951730@2] input input0: gpio keypad major:231
  766. [ 3.957090@2] cpuinfo: probe done
  767. [ 3.961080@1] input: cec_input as /devices/virtual/input/input1
  768. [ 3.966094@1] cectx aocec: aml_cec_probe(): no hdmirx reg resource
  769. [ 3.971601@1] cectx aocec: aml_cec_probe(): no hhi reg resource
  770. [ 3.977666@1] cectx aocec: aml_cec_probe(): can't find hdmirx
  771. [ 3.984316@1] cec: wake up flag:0
  772. [ 3.991107@2] aml-i2s-dai I2S.41: I2S Mic is in platform!
  773. [ 3.992252@1] aml_pcm_dai: pcm mode detection =1
  774. [ 3.998726@1] es8323 1-0010: id read invalid, id=56
  775. [ 4.025079@3] input input0: key 116 up
  776. [ 4.536745@1] es8323 init ok, drv version = v1.0
  777. [ 4.537953@1] aml_snd_card: headphone detection disable=1
  778. [ 4.541229@1] aml_snd_card: no spk event delay time set
  779. [ 4.549887@1] aml_snd_m8_card aml_m8_snd.48: es8323-hifi <-> I2S.41 mapping ok
  780. [ 4.555605@1] aml_snd_m8_card aml_m8_snd.48: dit-hifi <-> SPDIF.42 mapping ok
  781. [ 4.560838@1] aml_pcm: enter aml_pcm_new dai->name: PCM.43 dai->id: 0
  782. [ 4.567726@1] aml_snd_m8_card aml_m8_snd.48: pcm2bt-pcm <-> PCM.43 mapping ok
  783. [ 4.574170@1] aml_snd_m8_card aml_m8_snd.48: ASoC: no source widget found for LOUTL
  784. [ 4.581738@1] aml_snd_m8_card aml_m8_snd.48: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
  785. [ 4.590522@1] aml_snd_m8_card aml_m8_snd.48: ASoC: no source widget found for LOUTR
  786. [ 4.598082@1] aml_snd_m8_card aml_m8_snd.48: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
  787. [ 4.613727@3] aml_snd_card: audio use jtag pinmux as i2s output, read val =0
  788. [ 4.615526@2] TCP: cubic registered
  789. [ 4.621956@1] NET: Registered protocol family 10
  790. [ 4.625847@1] NET: Registered protocol family 17
  791. [ 4.627869@1] Key type dns_resolver registered
  792. [ 4.637405@1] Registering SWP/SWPB emulation handler
  793. [ 4.639909@2] regulator-dummy: disabling
  794. [ 5.344887@0] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  795. [ 5.344958@0] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
  796. [ 5.353624@0] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0xc9000000
  797. [ 5.358894@0] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
  798. [ 5.365740@0] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  799. [ 5.372955@0] usb usb1: Product: xHCI Host Controller
  800. [ 5.377992@0] usb usb1: Manufacturer: Linux 3.14.29 xhci-hcd
  801. [ 5.383588@0] usb usb1: SerialNumber: xhci-hcd.0.auto
  802. [ 5.390231@0] hub 1-0:1.0: USB hub found
  803. [ 5.392490@1] hub 1-0:1.0: 3 ports detected
  804. [ 5.396965@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  805. [ 5.402202@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
  806. [ 5.410131@1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
  807. [ 5.416874@1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  808. [ 5.424188@1] usb usb2: Product: xHCI Host Controller
  809. [ 5.429210@1] usb usb2: Manufacturer: Linux 3.14.29 xhci-hcd
  810. [ 5.434796@1] usb usb2: SerialNumber: xhci-hcd.0.auto
  811. [ 5.441703@1] hub 2-0:1.0: USB hub found
  812. [ 5.443717@2] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
  813. [ 5.453660@5] console [netcon0] enabled
  814. [ 5.454733@5] netconsole: network logging started
  815. [ 5.460156@5] rtc-aml_hym8563 2-0051: setting system clock to 2018-11-01 15:42:56 UTC (1541086976)
  816. [ 5.478077@5] gxbb_pm: enter meson_pm_probe!
  817. [ 5.478443@5] gxbb_pm: meson_pm_probe done
  818. [ 5.485743@1] cpucore_cooling_register, max_cpu_core_num:4
  819. [ 5.486575@1] cpucore_cooling_register, max_cpu_core_num:4
  820. [ 5.507533@0] aml_istbt_dev_ready NULL
  821. [ 5.507631@0] ALSA device list:
  822. [ 5.508781@0] #0: AML-M8AUDIO
  823. [ 5.513185@0] Freeing unused kernel memory: 912K (ffffffc0019fd000 - ffffffc001ae1000)
  824. [?25hCoreELEC:~ # [BL31]: tee size: 0
RAW Paste Data