Untitled

c@c-desktop:~$ sudo smartctl -a /dev/sdb
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-9-amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     HGST Travelstar 5K1000
Device Model:     HGST HTS541010A9E680
Serial Number:    JD100ACC2MXK4K
LU WWN Device Id: 5 000cca 792e53d3e
Firmware Version: JA0OA560
User Capacity:    1 000 204 886 016 bytes [1,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Sun Jul 12 19:21:07 2020 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (   45) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 241) minutes.
SCT capabilities:              (0x003d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   062    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   100   100   040    Pre-fail  Offline      -       0
  3 Spin_Up_Time            0x0007   253   253   033    Pre-fail  Always       -       1
  4 Start_Stop_Count        0x0012   099   099   000    Old_age   Always       -       2333
  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   040    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0012   013   013   000    Old_age   Always       -       38236
 10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       1097
191 G-Sense_Error_Rate      0x000a   100   100   000    Old_age   Always       -       65536
192 Power-Off_Retract_Count 0x0032   099   099   000    Old_age   Always       -       374
193 Load_Cycle_Count        0x0012   086   086   000    Old_age   Always       -       142721
194 Temperature_Celsius     0x0002   166   166   000    Old_age   Always       -       36 (Min/Max 17/48)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       44
197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0
223 Load_Retry_Count        0x000a   100   100   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 537 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 537 occurred at disk power-on lifetime: 12619 hours (525 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 d8 c4 67 00  Error: UNC at LBA = 0x0067c4d8 = 6800600

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 08 10 d8 c4 67 40 00      13:43:35.264  READ FPDMA QUEUED
  2f 00 01 10 00 00 e0 00      13:43:35.263  READ LOG EXT
  60 08 08 d8 c4 67 40 00      13:43:31.442  READ FPDMA QUEUED
  2f 00 01 10 00 00 e0 00      13:43:31.441  READ LOG EXT
  60 08 f8 d8 c4 67 40 00      13:43:27.609  READ FPDMA QUEUED

Error 536 occurred at disk power-on lifetime: 12619 hours (525 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 d8 c4 67 00  Error: UNC at LBA = 0x0067c4d8 = 6800600

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 08 08 d8 c4 67 40 00      13:43:31.442  READ FPDMA QUEUED
  2f 00 01 10 00 00 e0 00      13:43:31.441  READ LOG EXT
  60 08 f8 d8 c4 67 40 00      13:43:27.609  READ FPDMA QUEUED
  2f 00 01 10 00 00 e0 00      13:43:27.608  READ LOG EXT
  60 08 f0 d8 c4 67 40 00      13:43:23.775  READ FPDMA QUEUED

Error 535 occurred at disk power-on lifetime: 12619 hours (525 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 d8 c4 67 00  Error: UNC at LBA = 0x0067c4d8 = 6800600

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 08 f8 d8 c4 67 40 00      13:43:27.609  READ FPDMA QUEUED
  2f 00 01 10 00 00 e0 00      13:43:27.608  READ LOG EXT
  60 08 f0 d8 c4 67 40 00      13:43:23.775  READ FPDMA QUEUED
  2f 00 01 10 00 00 e0 00      13:43:23.774  READ LOG EXT
  60 08 e8 d8 c4 67 40 00      13:43:19.931  READ FPDMA QUEUED

Error 534 occurred at disk power-on lifetime: 12619 hours (525 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 d8 c4 67 00  Error: UNC at LBA = 0x0067c4d8 = 6800600

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 08 f0 d8 c4 67 40 00      13:43:23.775  READ FPDMA QUEUED
  2f 00 01 10 00 00 e0 00      13:43:23.774  READ LOG EXT
  60 08 e8 d8 c4 67 40 00      13:43:19.931  READ FPDMA QUEUED
  2f 00 01 10 00 00 e0 00      13:43:19.930  READ LOG EXT
  60 08 e0 d8 c4 67 40 00      13:43:16.109  READ FPDMA QUEUED

Error 533 occurred at disk power-on lifetime: 12619 hours (525 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 d8 c4 67 00  Error: UNC at LBA = 0x0067c4d8 = 6800600

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 08 e8 d8 c4 67 40 00      13:43:19.931  READ FPDMA QUEUED
  2f 00 01 10 00 00 e0 00      13:43:19.930  READ LOG EXT
  60 08 e0 d8 c4 67 40 00      13:43:16.109  READ FPDMA QUEUED
  2f 00 01 10 00 00 e0 00      13:43:16.108  READ LOG EXT
  60 08 d8 d8 c4 67 40 00      13:43:12.275  READ FPDMA QUEUED

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.