Khadas Vim infinite bootloop

Resetting CPU ...

resetting ...
GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 102009

BL2 Built : 14:59:36, Aug  9 2017.
gxl ge8c6a83 - xiaobo.gu@droid12

set vcck to 1120 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 768MHz - PASS
Rank0: 1024MB(auto)-2T-11
Rank1: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x05100000, size: 0x0002c600
Load bl33 from eMMC, src: 0x00050200, des: 0x01000000, size: 0x00065200
NOTICE:  BL3-1: v1.0(release):801e730
NOTICE:  BL3-1: Built : 22:09:38, Aug 10 2017
[BL31]: GXL CPU setup!
NOTICE:  BL31: BL33 decompress pass
mpu_config_enable:ok
[Image: gxl_v1.1.3244-a3237e2 2017-08-16 14:01:18 hong.guo@droid04]
OPS=0x82
e2 a0 1 a7 87 16 68 d fb 59 4 21 [0.326213 Inits done]
secure task start!
high task start!
low task start!
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01-gc4149cc16e (Oct 19 2017 - 15:35:09)

DRAM:  2 GiB
Relocation Offset is: 76eb7000
register usb cfg[0][1] = 0000000077f58a60
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpu: vpu_clk_gate_init_off
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC:   aml_priv->desc_buf = 0x0000000073eb76b0
aml_priv->desc_buf = 0x0000000073eb99d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
init_part() 293: PART_TYPE_AML
[mmc_init] mmc init success
start dts,buffer=0000000073ebc200,dt_addr=0000000073ebc200
get_partition_from_dts: not find /partitions node FDT_ERR_NOTFOUND.
get_ptbl_from_dtb()-260: get partition table from dts faild
mmc_device_init()-1082: get partition table from dtb failed
init_part() 293: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x6c00000
In:    serial
Out:   serial
Err:   serial
reboot_mode=watchdog_reboot
itest - return true/false on integer compare

Usage:
itest [.b, .w, .l, .s] [*]value1 <op> [*]value2
hpd_state=0
set hdmitx VIC = 16
config HPLL = 2970000
HPLL: 0xc000027b
config HPLL done
j = 4  vid_clk_div = 1
hdmitx: set enc for VIC: 16
HDMITX-DWC addr=0x10004006 rd_data=0x40
Error: HDMITX-DWC exp_data=0xff mask=0x9f
rx version is 1.4 or below  div=10
hdmtix: set audio
hdmitx phy setting done
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-909: calc 487f8ec0, store 487f8ec0
_verify_dtb_checksum()-909: calc 487f8ec0, store 487f8ec0
dtb_read()-1031: total valid 2
dtb_read()-1098: do nothing
saradc: not find the node /saradc: FDT_ERR_NOTFOUND
"Synchronous Abort" handler, esr 0x96000210
ELR:     77efa294
LR:      77efa288
x0 : 0000000077fbb620 x1 : 0000000000000000
x2 : 0000000000000000 x3 : 00000000c81004c0
x4 : 0000000000000000 x5 : 0000000000000020
x6 : ffffff80ffffffc8 x7 : 0000000000005598
x8 : 0000000073ea69b0 x9 : 0000000000000000
x10: 0000000000000000 x11: 0000000073ea684c
x12: 00000000ffffffff x13: 00000000ffffffff
x14: 0000000000000000 x15: 0000000000000000
x16: 0000000000000000 x17: 0000000000000000
x18: 0000000073ea6e28 x19: 0000000000000001
x20: 0000000073ebd0b0 x21: 0000000000000000
x22: 0000000000000003 x23: 0000000077f70a78
x24: 0000000000000000 x25: 0000000000000000
x26: 0000000000000000 x27: 0000000000000000
x28: 0000000073ebd0e0 x29: 0000000073ea6b10

Resetting CPU ...