Untitled

ROM VER: 1.0.3
CFG 01
Read EEPROMX
 X


SHC Danube-External-Flash-Boot - Version V1.2
Mem-config:
Flash:  8MB- 8MBx1
Ram:   32MB-32MBx1

Low level dbg is active...

CPU0
MEMS

ROM VER: 1.0.3
CFG 01
Read EEPROMX
 X


SHC Danube-External-Flash-Boot - Version V1.2
Mem-config:
Flash:  8MB- 8MBx1
Ram:   32MB-32MBx1

Low level dbg is active...

CPU0
MEMS

[32m	-- Danube Primary loader --
	Version		: 4.1.24.52.12
	Build Profile	: sx76x_danube_a
	Build Date	: Jun 10 2009 - 17:11:31[0m

	--> Extract primary loader			[[32m  OK  [0m]
	--> Validate secondary loader (FLASH)		[[32m  OK  [0m]

[32m	-- Danube Secondary loader --
	Version		: 4.1.28.52.12
	Build Profile	: sx76x_danube_b
	Build Date	: Dec 15 2009 - 17:54:55[0m

	--> Extract secondary loader			[[32m  OK  [0m]
	--> Press enter to activate cli			[  01  ]00
## Starting application at 0xB0020000 ...


U-Boot 2010.03 (Apr 29 2011 - 22:24:28)

Board: unknown, chip part number 0x12B V1.3, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM:  32 MB
Flash:  8 MB
Net:   lq_cpe_eth
Hit any key to stop autoboot:  2  0
DANUBE => run update_openwrt
Using lq_cpe_eth device
TFTP from server 192.168.2.16; our IP address is 192.168.2.1
Filename 'openwrt-lantiq-xway-GIGASX76X-squashfs.image'.
Load address: 0x80500000
Loading: *#################################################################
	 #################################################################
	 #################################################################
	 ###################################################
done
Bytes transferred = 3604484 (370004 hex)

........................................................ done
Erased 56 sectors
Copy to Flash... 9....8....7....6....5....4....3....2....1....done
DANUBE => run flash_flash
## Booting kernel from Legacy Image at b0050000 ...
   Image Name:   MIPS OpenWrt Linux-2.6.37.6
   Created:      2011-05-01  20:38:14 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    905967 Bytes = 884.7 kB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.37.6 (kombajn@SPEEDTOUCH) (gcc version 4.5.2 (Linaro GCC 4.5-2011.02-0) ) #8 Sun May 1 22:38:10 CEST 2011

cpu: 333333334

fpi: 83333333

io: 83250000

SoC: Danube rev1.3 333Mhz

bootconsole [early0] enabled

CPU revision is: 00019641 (MIPS 24Kc)

Determined physical RAM map:

 memory: 02000000 @ 00000000 (usable)

Initrd not found or empty - disabling initrd

Zone PFN ranges:

  Normal   0x00000000 -> 0x00002000

Movable zone start PFN for each node

early_node_map[1] active PFN ranges

    0: 0x00000000 -> 0x00002000

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128

Kernel command line: console=ttyS1,115200 rootfstype=squashfs,jffs2 machtype=GIGASX76X

PID hash table entries: 128 (order: -3, 512 bytes)

Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)

Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)

Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.

Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

Writing ErrCtl register=0001e438

Readback ErrCtl register=0001e438

Memory: 29668k/32768k available (2140k kernel code, 3100k reserved, 352k data, 152k init, 0k highmem)

NR_IRQS:256

Calibrating delay loop... 221.69 BogoMIPS (lpj=443392)

pid_max: default: 32768 minimum: 301

Mount-cache hash table entries: 512

NET: Registered protocol family 16

MIPS: machine is GIGASX76X - Gigaset SX762 and SX763

bio: create slab <bio-0> at 0

pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]

pci 0000:00:0e.0: BAR 0: set to [mem 0x18000000-0x1800ffff] (PCI address [0x18000000-0x1800ffff])

pci 0000:00:0e.1: BAR 1: assigned [mem 0x18010000-0x18010fff]

pci 0000:00:0e.1: BAR 1: set to [mem 0x18010000-0x18010fff] (PCI address [0x18010000-0x18010fff])

pci 0000:00:0e.1: BAR 0: assigned [io  0x1ae00000-0x1ae00007]

pci 0000:00:0e.1: BAR 0: set to [io  0x1ae00000-0x1ae00007] (PCI address [0x1ae00000-0x1ae00007])

arch/mips/pci/pci-lantiq.c:pcibios_map_irq[263]14 1

arch/mips/pci/pci-lantiq.c:pcibios_map_irq[263]14 1

Switching to clocksource MIPS

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 1024 (order: 1, 8192 bytes)

TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

TCP: Hash tables configured (established 1024 bind 1024)

TCP reno registered

UDP hash table entries: 256 (order: 0, 4096 bytes)

UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

NET: Registered protocol family 1

gptu: totally 6 16-bit timers/counters

gptu: misc_register on minor 63

gptu: succeeded to request irq 126

gptu: succeeded to request irq 127

gptu: succeeded to request irq 128

gptu: succeeded to request irq 129

gptu: succeeded to request irq 130

gptu: succeeded to request irq 131

squashfs: version 4.0 (2009/01/31) Phillip Lougher

JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

msgmni has been set to 57

io scheduler noop registered

io scheduler deadline registered (default)

lq_asc.0: ttyS0 at MMIO 0x1e100400 (irq = 104) is a lq_asc

lq_asc.1: ttyS1 at MMIO 0x1e100c00 (irq = 112) is a lq_asc

console [ttyS1] enabled, bootconsole disabled
console [ttyS1] enabled, bootconsole disabled

lq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001000
Amd/Fujitsu Extended Query Table at 0x0040
  Amd/Fujitsu Extended Query version 1.3.
number of CFI chips: 1
Creating 6 MTD partitions on "lq_nor":
0x00000000e000-0x000000010000 : "secondary_env"
0x000000010000-0x000000020000 : "secondary_boot"
0x000000020000-0x000000030000 : "uboot"
0x000000030000-0x000000050000 : "uboot_env"
0x000000050000-0x0000007f0000 : "linux"
Creating 2 MTD partitions on "lq_nor":
0x000000050000-0x00000012d32f : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x00000012d32f-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=3B0000, len=440000
0x0000003b0000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "board_config"
Loading ADM6996 driver...

6996I SMI Mode-Chip ID:71023

eth0: using mac=12:9C:E1:21:C9:8E
lq_mii: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:00, irq=-1)
lq_etop: driver loaded!
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
All bugs added by David S. Miller <[email protected]>
VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
Freeing unused kernel memory: 152k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -

Please press Enter to activate this console. device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering forwarding state
br-lan: port 1(eth0) entering forwarding state
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 8
NET: Registered protocol family 20
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
nf_conntrack version 0.5.0 (465 buckets, 1860 max)
xt_time: kernel timezone is -0000
IFX MEI Version 5.00.00

Infineon CPE API Driver version: DSL CPE API V3.24.4.4
Infineon Technologies ATM driver version 1.0.8
Infineon Technologies ATM (A1) firmware version 0.1
ifxmips_atm: ATM init succeed
dwc_otg: version 2.60a 22-NOV-2006
DWC_otg: Using DMA mode
dwc_otg dwc_otg.0: DWC OTG Controller
dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
dwc_otg dwc_otg.0: irq 62, io mem 0xffffffffbe101000
DWC_otg: Init: Port Power? op_state=1
DWC_otg: Init: Power Port (0)
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
DISCONNECTED PORT
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.


BusyBox v1.18.4 (2011-04-28 19:41:38 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 ATTITUDE ADJUSTMENT (bleeding edge, r26773) ----------
  * 1/4 oz Vodka      Pour all ingredents into mixing
  * 1/4 oz Gin        tin with ice, strain into glass.
  * 1/4 oz Amaretto
  * 1/4 oz Triple sec
  * 1/4 oz Peach schnapps
  * 1/4 oz Sour mix
  * 1 splash Cranberry juice
 -----------------------------------------------------
root@OpenWrt:/# jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
JFFS2 notice: (1236) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
u32 classifier
    Performance counters on
    input device check on
    Actions configured
Mirror/redirect action on