[    5.766080] zswap: loaded using pool lzo/zbud
[    5.771505] Key type ._fscrypt registered
[    5.775675] Key type .fscrypt registered
[    5.779654] Key type fscrypt-provisioning registered
[    5.788987] Btrfs loaded, crc32c=crc32c-generic
[    5.793801] AppArmor: AppArmor sha1 policy hashing enabled
[    5.825149] OMAP GPIO hardware version 0.1
[    5.856023] tps65217-pmic: Failed to locate of_node [id: -1]
[    5.873771] tps65217-bl: Failed to locate of_node [id: -1]
[    5.882894] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set
[    5.890411] input: tps65217_pwr_but as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0
[    5.909078] tps65217 0-0024: TPS65217 ID 0xe version 1.2
[    5.915164] at24 0-0050: supply vcc not found, using dummy regulator
[    5.922522] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
[    5.930768] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
[    5.940423] at24 2-0054: supply vcc not found, using dummy regulator
[    5.979341] at24 2-0055: supply vcc not found, using dummy regulator
[    6.015047] at24 2-0056: supply vcc not found, using dummy regulator
[    6.051034] at24 2-0057: supply vcc not found, using dummy regulator
[    6.086564] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz
[    6.112660] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22)
[    6.122786] remoteproc remoteproc0: powering up wkup_m3
[    6.134162] remoteproc remoteproc0: Booting fw image am335x-pm-firmware.elf, size 217148
[    6.146183] PM: Cannot get wkup_m3_ipc handle
[    6.150913] sdhci-omap 48060000.mmc: Got CD GPIO
[    6.155977] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator
[    6.164866] remoteproc remoteproc0: remote processor wkup_m3 is now up
[    6.164887] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version = 0x192
[    6.207758] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA
[    6.287481] mmc0: new high speed SDHC card at address aaaa
[    6.294288] mmcblk0: mmc0:aaaa SC16G 14.8 GiB
[    6.307945] tda998x 0-0070: found TDA19988
[    6.317875]  mmcblk0: p1 p2
[    6.323633] tilcdc 4830e000.lcdc: bound 0-0070 (ops 0xc109add0)
[    6.331533] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0
[    6.339518] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes
[    6.349095] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes
[    6.358213] PM: bootloader does not support rtc-only!
[    6.366305] ALSA device list:
[    6.369590]   #0: TI BeagleBone Black
[    6.387921] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    6.396271] VFS: Mounted root (ext4 filesystem) readonly on device 179:770.
[    6.408618] Freeing unused kernel memory: 1024K
[    6.414003] Run /sbin/init as init process
[    6.418164]   with arguments:
[    6.421181]     /sbin/init
[    6.423925]     earlyprintk
[    6.426732]   with environment:
[    6.429912]     HOME=/
[    6.432306]     TERM=linux
[    6.447558] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist.