VBus is low (not a "chinese charger"), SoftService is not asserted...
CONF_FUSE 0-4 = 0x0077bd4b 0x02041447 0x30044809 0xbc67bb5f 0x0020c3f0
HW_REVISION_NUMBER = 0x202400e1
OEM_ID = 0x00010001

SEMCSEC Secure Bootstrap "1226-2253 S1Boot QSD8x50 CRH1099189_R8A033" (2010-09-28 12:04)
Detected memories:
 SMI CS0: Samsung 64MB LPDDR (SR 0x4e01)
 EBI1 CS0: Micron 256MB LPDDR (SR 0x630f)
 EBI1 CS1: Micron 128MB LPDDR (SR 0x6b0f)
 EBI2 CS0: Micron 1024MB NAND (0x002c 0x00b3)
OTP User segment locked
OTP User segment locked
TA @ 0x08100000 (8*128kB)
Hardware Config: verification OK
MSN=CB511TLMFQ IMEI=01259000617646
OTP User segment locked
Service Mode Config From TA: KEYS:1 USB:ON SERVICEMODE:USB SERVICE_PIN:ENABLED
TA_ReadData FlaFla is set
S1 BOOT waiting for USB connection
s1_main_loop: No Service mode comm interface found!
Configuring long press:800
plf_bootos QSD8x50
Startup reason before override: PWRKEY
Partition table contents:
 PartID     Descr   Attribs    StartBlock NumBlocks  UsedAs
 0x00000001 S1Boot  0x00000022 0x00000000 0x00000001
 0x00000002 TA      0x00000001 0x00000008 0x00000008
 0x00000005 ModemSW 0x00000022 0x00000016 0x000000bf mARM image
 0x00000008 AppDSP  0x00000022 0x000001d3 0x000000a2 aDSP image
 0x0000000f AppsFS3 0x00000001 0x00001c64 0x0000037a
 0x0000000b FOTA0   0x00000022 0x0000012d 0x00000022
 0x0000000c FOTA1   0x00000022 0x0000014f 0x00000022
 0x00000003 Linux   0x00000022 0x00000275 0x00000062 aARM image
 0x00000006 ModemFS 0x00000001 0x000000d5 0x00000058 mARM-FS image
 0x00000004 AppsFS1 0x00000001 0x000002d7 0x00000b05
 0x00000009 AppsFS2 0x00000001 0x00000ddc 0x00000e88
 0x0000000e Recover 0xc0000022 0x00000171 0x00000062
 0x00000010 AppLog  0x80000001 0x00001fde 0x00000022
ARM ELF image (0x0028), entry point @ 0x00400000
QDSP6 ELF image (0x00a4), entry point @ 0x2e802000
SIN Verification of aARM failed!
ARM ELF image (0x0028), entry point @ 0x20008000
plf_ta_cmd_params()
Adding TA 8a2 as 8a2 to commandline
ta_to_cmdline() unit is 8a2 label is 8a2
The label string is:000008A2.
The data string is:58313069.
The new command line entry:semcandroidboot.000008A2=58313069
Commandline:semcandroidboot.serialno=CB511TLMFQ semcandroidboot.startup=0x00000001 semcandroidboot.000008A2=58313069.
Warmboot address calculated: 0x20000000
TCSR_SPARE2(SA_fuse)=0xa037, EF_CFG2=0x40040801, EF_CFG3=0x04024002, EF_CFG4=0xed41e600, EF_CFG6=0x083007e0
Longpress NOT OK - startup inhibited


VBus is low (not a "chinese charger"), SoftService is not asserted...
CONF_FUSE 0-4 = 0x0077bd4b 0x02041447 0x30044809 0xbc67bb5f 0x0020c3f0
HW_REVISION_NUMBER = 0x202400e1
OEM_ID = 0x00010001

SEMCSEC Secure Bootstrap "1226-2253 S1Boot QSD8x50 CRH1099189_R8A033" (2010-09-28 12:04)
Detected memories:
 SMI CS0: Samsung 64MB LPDDR (SR 0x4e01)
 EBI1 CS0: Micron 256MB LPDDR (SR 0x630f)
 EBI1 CS1: Micron 128MB LPDDR (SR 0x6b0f)
 EBI2 CS0: Micron 1024MB NAND (0x002c 0x00b3)
OTP User segment locked
OTP User segment locked
TA @ 0x08100000 (8*128kB)
Hardware Config: verification OK
MSN=CB511TLMFQ IMEI=01259000617646
OTP User segment locked
Service Mode Config From TA: KEYS:1 USB:ON SERVICEMODE:USB SERVICE_PIN:ENABLED
TA_ReadData FlaFla is set
S1 BOOT waiting for USB connection
s1_main_loop: No Service mode comm interface found!
Configuring long press:800
plf_bootos QSD8x50
Startup reason before override: PWRKEY
Partition table contents:
 PartID     Descr   Attribs    StartBlock NumBlocks  UsedAs
 0x00000001 S1Boot  0x00000022 0x00000000 0x00000001
 0x00000002 TA      0x00000001 0x00000008 0x00000008
 0x00000005 ModemSW 0x00000022 0x00000016 0x000000bf mARM image
 0x00000008 AppDSP  0x00000022 0x000001d3 0x000000a2 aDSP image
 0x0000000f AppsFS3 0x00000001 0x00001c64 0x0000037a
 0x0000000b FOTA0   0x00000022 0x0000012d 0x00000022
 0x0000000c FOTA1   0x00000022 0x0000014f 0x00000022
 0x00000003 Linux   0x00000022 0x00000275 0x00000062 aARM image
 0x00000006 ModemFS 0x00000001 0x000000d5 0x00000058 mARM-FS image
 0x00000004 AppsFS1 0x00000001 0x000002d7 0x00000b05
 0x00000009 AppsFS2 0x00000001 0x00000ddc 0x00000e88
 0x0000000e Recover 0xc0000022 0x00000171 0x00000062
 0x00000010 AppLog  0x80000001 0x00001fde 0x00000022
ARM ELF image (0x0028), entry point @ 0x00400000
QDSP6 ELF image (0x00a4), entry point @ 0x2e802000
SIN Verification of aARM failed!
ARM ELF image (0x0028), entry point @ 0x20008000
plf_ta_cmd_params()
Adding TA 8a2 as 8a2 to commandline
ta_to_cmdline() unit is 8a2 label is 8a2
The label string is:000008A2.
The data string is:58313069.
The new command line entry:semcandroidboot.000008A2=58313069
Commandline:semcandroidboot.serialno=CB511TLMFQ semcandroidboot.startup=0x00000001 semcandroidboot.000008A2=58313069.
Warmboot address calculated: 0x20000000
TCSR_SPARE2(SA_fuse)=0xa037, EF_CFG2=0x40040801, EF_CFG3=0x04024002, EF_CFG4=0xed41e600, EF_CFG6=0x083007e0
Longpress OK - starting up
EBI1 MPU Partition 0 start:0x2e802000 end:0x2fe26000
SMI  MPU Partition 0 start:0x00400000 end:0x02585000
SMI  MPU Partition 1 start:0x00200000 end:0x00400000
NAND MPU Partition 0 start:0x00001fde end:0x00002000
NAND MPU Partition 1 start:0x00000171 end:0x000001d3
NAND MPU OFF according to partition table
Jumping to code @ 0x00400000, goodbye and thanks for all the fish...
Linux version 2.6.29-FXP (SEMCUser@SEMCHost) (gcc version 4.4.3 (GCC) ) #1 PREEMPT Wed Feb 15 20:56:52 EET 2012
CPU: ARMv7 Processor [510f00f2] revision 2 (ARMv7), cr=10c5387f
CPU: VIPT nonaliasing data cache, VIVT ASID tagged instruction cache
Machine: ES209RA
Partition (from atag) cache -- Offset:1c64 Size:37a
Partition (from atag) system -- Offset:2d7 Size:b05
Partition (from atag) userdata -- Offset:ddc Size:e88
Partition (from atag) appslog -- Offset:1fde Size:22
Partition (from atag) boot -- Offset:275 Size:62
Memory policy: ECC disabled, Data cache writeback
allocating 163840 bytes at c0a00000 (20a00000 physical) for kernel ebi1 pmem arena
allocating 29954048 bytes at c0a28000 (20a28000 physical) for mdp pmem arena
allocating 35217408 bytes at c4139000 (24139000 physical) for adsp pmem arena
using 3145728 bytes of SMI at 2b00000 physical for fb
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 91138
Kernel command line: console=ttyMSM0 semcandroidboot.serialno=CB511TLMFQ semcandroidboot.startup=0x00000001 semcandroidboot.000008A2=58313069
USB serial number: CB511TLMFQ
Unknown boot option `semcandroidboot.startup=0x00000001': ignoring
Unknown boot option `semcandroidboot.000008A2=58313069': ignoring
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 232MB 127MB = 359MB total
Memory: 292736KB available (5076K code, 909K data, 156K init)
Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 936 bytes
NET: Registered protocol family 16
Waiting for Modem...
socinfo_init: v3, id=30, ver=0.0, raw_id=0, raw_ver=0, hw_plat=0
es209ra_init: startup_reason: 0x00000000
PVR0F2: 0
PVR0F2: 10
Max ACPU freq from efuse data is 1228800 KHz
ACPU running at 384000 KHz
21 scaling frequencies supported.
ram_console: got buffer at 37fe0000, size 20000
ram_console: no valid data in buffer (sig = 0x40001000)
console [ram-1] enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
msm_i2c_probe
msm_i2c_probe: clk_ctl 316, 384000 Hz
msm_i2c_gpio_config: es209ra has only primary I2C.
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: calling CRDA failed - unable to update world regulatory domain, using static definition
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 1248K
last_amsslog: Log not present
smd_alloc_channel() cid 41 does not exist
SMD Control Port Driver Initialized.
smd_alloc_channel() cid 51 does not exist
Using very old AMSS modem firmware.
H2W: Registering H2W (headset) driver
input: es209ra_keypad as /devices/virtual/input/input0
ES209RA Audio Jack Driver : irq locked. value = 1
ES209RA Audio Jack Driver : probe finished
RPC_TIME_TOD_SET_APPS_BASES:
        tick = 202915
        stamp = 1026516069
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
ashmem: initialized
fuse init (API version 7.11)
yaffs Feb 15 2012 20:56:45 Installing.
msgmni has been set to 574
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler bfq registered (default)
msm_fb_probe:  phy_Addr = 0x2b00000 virt = 0xd8400000
MDP HW Base phy_Address = 0xaa200000 virt = 0xd8100000
primary mddi base phy_addr = 0xaa600000 virt = 0xd8010000
__msm_rpc_connect: server not found 30000061:30001
__msm_rpc_connect: server not found 30000061:20001
FrameBuffer[0] 480x854 size=1770752 bytes is registered successfully!
diagfwd initializing ..
diag opened SMD port ; r = 0
diag opened SMD port ; r = 0
diagchar initializing ..
diagchar initialized
[drm] Initialized drm 1.1.0 20060810
msm_serial: detected port #0
msm_serial.0: ttyMSM0 at MMIO 0xa9a00000 (irq = 229) is a MSM
msm_serial: console setup on port #0
console [ttyMSM0] enabled
msm_serial: driver initialized
msm_serial_hs.1: ttyHS1 at MMIO 0xa0900000 (irq = 52) is a MSM HS UART
msm_serial_hs module loaded
brd: module loaded
loop: module loaded
pmem: Initializing pmem_kernel_ebi1 (in-kernel)
pmem: Initializing pmem (user-space) as cached
pmem: Initializing pmem_adsp (user-space) as non-cached
pmem: Initializing pmem_venc (user-space) as non-cached
PROXIMITY driver installation succeeded
wlan_power init
TPS65023: PMIC probed.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
CSLIP: code copyright 1989 Regents of the University of California.
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
rmnet0 (): not using net_device_ops yet
rmnet1 (): not using net_device_ops yet
rmnet2 (): not using net_device_ops yet
Linux video capture interface: v2.00
Driver 'sd' needs updating - please use bus_type methods
SCSI Media Changer driver v0.25
Driver 'ch' needs updating - please use bus_type methods
msm_nand: phys addr 0xa0a00000
dmac 0x7
allocated dma buffer at ffc13000, dma_addr 370ec000
status: e03020
nandid: 55d1b32c maker 2c device b3
Found a supported NAND device
NAND Id  : 0x55d1b32c
Buswidth : 16 Bits
Density  : 1024 MByte
Pagesize : 2048 Bytes
Erasesize: 131072 Bytes
Oobsize  : 64 Bytes
ecmdcycle: 3 erase cycle
2nd_bbm  : 0
CFG0 Init  : 0xa85408c0
CFG1 Init  : 0x0004745e
ECCBUFCFG  : 0x00000203
Creating 5 MTD partitions on "msm_nand":
0x000038c80000-0x00003fbc0000 : "cache"
0x000005ae0000-0x00001bb80000 : "system"
ES209RA Audio Jack Driver : previous_state = 0
ES209RA Audio Jack Driver : current_state = 0
0x00001bb80000-0x000038c80000 : "userdata"
0x00003fbc0000-0x000040000000 : "appslog"
0x000004ea0000-0x000005ae0000 : "boot"
msm_hsusb_rpc_connect: rpc connect success vers = 10001
msm_otg_probe: rpc_connect(0)
msm72k_udc: msm72k_probe
__msm_rpc_connect: server not found 3000001a:20001
msm_chg_rpc_connect: connected to rpc vers = 10001
peripheral driver registered w/ tranceiver
msm_otg_suspend: usb in low power mode
android_probe pdata: c05308e4
android_bind
android_usb gadget: android_usb ready
msm72k_udc: registered gadget driver 'android_usb'
f_adb init
android_register_function adb
f_mass_storage init
android_register_function usb_mass_storage
f_serial init
android_register_function modem
android_register_function nmea
f_rndis init
android_register_function rndis
f_diag init
android_register_function diag
rndis_function_bind_config MAC: 02:17:0E:78:77:60
android_usb gadget: using random self ethernet address
android_usb gadget: using random host ethernet address
usb0: MAC 1a:8d:74:4a:e9:a0
usb0: HOST MAC 0a:f2:68:99:03:97
mass_storage_function_add
fsg_probe pdata: c0532474
android_usb gadget: Number of LUNs=1
adb_bind_config
diag_function_add
input: es209ra_touch as /devices/platform/spi_qsd.0/spi0.0/input/input1

es209ra_touch, module init, result = 0
GPIO Matrix Keypad Driver: Start keypad matrix for es209ra_keypad in interrupt mode
GPIO Input Driver: Start gpio inputs for es209ra_keypad in interrupt mode
input: es209ra_keypad as /devices/virtual/input/input2
input: bma150 as /devices/virtual/input/input3
msm_rpc_client_req: RPC call was not successful (3)
rs30000048 rs30000048.65536: rtc core: registered msm_rtc as rtc0
rs30000048 rs30000048.65536: rtc core: registered msm_rtc_secure as rtc1
i2c /dev entries driver
input: compass as /devices/virtual/input/input4
Error: Driver 'bma150' is already registered, aborting...
max17040 fuel gauge driver init
max17040_fuel_gauge 0-0036: max17040 fuel gauge driver probe
max17040_fuel_gauge 0-0036: Load custom model
max17040_fuel_gauge 0-0036: SOC register's value that verify custom model : 0xdc61
max17040_fuel_gauge 0-0036: Succeeded to verify custom model. SOC register's value match desired value.
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: MSM Sleep Mode Driver Ver 1.1
mmc0: Qualcomm MSM SDCC at 0x00000000a0300000 irq 24,87 dma 8
mmc0: 8 bit data mode disabled
mmc0: 4 bit data mode enabled
mmc0: polling status mode disabled
mmc0: MMC clock 144000 -> 49152000 Hz, PCLK 30720000 Hz
mmc0: Slot eject status = 0
mmc0: Power save feature enable = 1
mmc0: DM non-cached buffer at ffc17000, dma_addr 0x37162000
mmc0: DM cmd busaddr 0x37162000, cmdptr busaddr 0x37162300
mmc1: No card detect facilities available
mmc1: Qualcomm MSM SDCC at 0x00000000a0400000 irq 26,0 dma 8
mmc1: 8 bit data mode disabled
mmc1: 4 bit data mode enabled
mmc1: polling status mode disabled
mmc1: MMC clock 144000 -> 49152000 Hz, PCLK 30720000 Hz
mmc1: Slot eject status = 0
mmc1: Power save feature enable = 1
mmc1: DM non-cached buffer at ffc18000, dma_addr 0x37165000
mmc1: DM cmd busaddr 0x37165000, cmdptr busaddr 0x37165300
Registered led device: lv5219lg:rgb1:red
Registered led device: lv5219lg:rgb1:green
Registered led device: lv5219lg:rgb1:blue
Registered led device: lv5219lg:fled
Registered led device: lv5219lg:mled
Registered led device: lv5219lg:sled
lv5219lg probed
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
logger: created 64K log 'log_system'
ramzswap: num_devices not specified. Using default: 1
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (5744 buckets, 22976 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
clock_late_init() disabled 22 unused clocks
input: 8k_handset as /devices/virtual/input/input5
hs_rpc_cb_init: couldn't open rpc client with version 2 err -113
hs_rpc_cb_init:▒yaffs: dev is 32505857 name is "mtdblock1"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.1, "mtdblock1"
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new high speed SDHC card at address 2171
mmcblk0: mmc0:2171 APPSD 15.4 GiB
 mmcblk0: p1
yaffs: restored from checkpoint
yaffs_read_super: isCheckpointed 1
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: restored from checkpoint
yaffs_read_super: isCheckpointed 0
yaffs: dev is 32505856 name is "mtdblock0"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.0, "mtdblock0"
yaffs: restored from checkpoint
yaffs_read_super: isCheckpointed 1
save exit: isCheckpointed 1
enabling adb
adb_open
^@sh: can't access tty; job control turned off
$ warning: `rild' uses 32-bit capabilities (legacy support in use)
select 711 (ueventd), adj 0, size 36, to kill
send sigkill to 711 (ueventd), adj 0, size 36
ramzswap: /dev/ramzswap0 initialized: disksize_kb=76564<6>Adding 76556k swap on /dev/block/ramzswap0.  Priority:-1 extents:1 across:76556k SS
pcm_out: open
audio: init: codecs
dal_attach: status = 0, name = 'DAL_AQ_AUD'
audio: init: INIT
audio: init: OPEN control
audio: init: attach ACDB
dal_attach: status = 0, name = 'DAL_AM_AUD'
audio: init: attach ADIE
dal_attach: status = 0, name = 'DAL_AM_AUD'
msm_kgsl kgsl-3d0: firmware: requesting yamato_pm4.fw
msm_kgsl kgsl-3d0: firmware: requesting yamato_pfp.fw
msm_kgsl: initialized dev=0 mmu=on per_process_pagetable=off
Normal WIFI mode.
ar6000_pwr_on --enter
wow_irq 158, ret 0
ar6000_readwrite_file: file /sys/devices/platform/msm_sdcc.2/detect_change filp_open error -2
mmc1: new SDIO card at address 0001
ar6000_available
ar6000_readwrite_file: file /sys/devices/platform/msm_sdcc.2/detect_change filp_open error -2
AR6000: Unsupported configuration opcode: 3
Firmware mode set
AR6000: Unsupported configuration opcode: 3
AR6000: Unsupported configuration opcode: 5
 BMI enabled
ar6000_avail: name=wlan0 hifdevice=0xd6c71000, dev=0xd6f18000 (0), ar=0xd6f18360
old options [0] old sleep [29]
Set hi_refclk_hz : Ref Clock=19200000
get_reg_code_from_file: file read error, length=[0x0]
AR6000: eeprom transfer by HOST
eeprom_ar6000_transfer: Enter
enable_SI
read_mac_addr_from_file try to open file /data/misc/wifi/mac_address
read_mac_addr_from_file file offset opsition: 0h
read_mac_addr_from_file: length=17
update_regCode : 0x60
AR6K: Original Region Code= 0x4067
disable_SI
AR6000: BMISetAppStart
AR6000: enable HI_OPTION_TIMER_WAR
AR6000: firmware_transfer
firmware_transfer: /system/lib/modules/athwlan.bin.z77 size 95404 bufsize 98304
firmware_transfer: BMILZData: len=8192, remaining=90112
firmware_transfer: BMILZData: len=8192, remaining=81920
ES209RA Audio Jack Driver : No Device
firmware_transfer: BMILZData: len=8192, remaining=73728
firmware_transfer: BMILZData: len=8192, remaining=65536
firmware_transfer: BMILZData: len=8192, remaining=57344
firmware_transfer: BMILZData: len=8192, remaining=49152
firmware_transfer: BMILZData: len=8192, remaining=40960
firmware_transfer: BMILZData: len=8192, remaining=32768
firmware_transfer: BMILZData: len=8192, remaining=24576
firmware_transfer: BMILZData: len=8192, remaining=16384
firmware_transfer: BMILZData: len=8192, remaining=8192
request_suspend_state: wakeup (3->0) at 18630525709 (2017-03-29 15:12:09.274708790 UTC)
firmware_transfer: BMILZData: len=8192, remaining=0
ADDRCONF(NETDEV_UP): wlan0: link is not ready
firmware_transfer: /system/lib/modules/data.patch.hw2_0.bin size 1328 bufsize 4096
ar6000_init() Got WMI @ 0xd6e78e00.
mac address = 8c:64:22:1c:90:77
wmi_control_rx() : Unknown id 0x101e
ar6000_init() WMI is ready
AR6000 Reg Code = 0x60
AR6K: set txpwr : 14 successfully
AR6000 scan complete: 0
channel hint set to 2462
Connect called with authmode 5 dot11 auth 1 PW crypto 4 PW crypto Len 0 GRP crypto 4 GRP crypto Len 0
AR6000 connected event on freq 2462 with bssid e2:4a:03:76:ff:90  listenInterval=1000, beaconInterval = 100, beaconIeLen = 22 assocReqLen=65 assocRespLen =57
Network: Infrastructure

BeaconIEs= 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00

AssocRespIEs= 01 08 82 84 8b 96 12 24 48 6c 32 04 0c 18 30 60 dd 18 00 50 f2 02 01 01 00 00 03 a4 00 00 27 a4 00 00 42 43 5e 00 62 32 2f 00 dd 07 00 0c 43 04 00 00 00
AssocReqIEs= 00 0c 52 6f 73 73 43 6f 6d 50 6f 7a 6f 72 01 08 82 84 8b 0c 12 96 18 24 32 04 30 48 60 6c 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00 dd 07 00 50 f2 02 00 01 00
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
AR6000 Neighbor Report Event
bssid e2:4a:03:76:ff:90
Enter - streamType=5, status=2
DHCP DISCOVER stop A2DP
Enter - streamType=5, status=1
DHCP ACK received start A2DP
RPC_TIME_TOD_SET_APPS_BASES:
        tick = 1214375
        stamp = 61595246978400256
rs30000048 rs30000048.65536: setting system clock to 2017-03-29 15:21:47 UTC (1490800907)