Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- F0: 102B 0000
- F6: 0000 0000
- V0: 0000 0000 [0001]
- 00: 0000 0000
- BP: 0000 0041 [0000]
- G0: 0190 0000
- T0: 0000 036D [000F]
- Jump to BL
- UNIVPLL_CON0 = 0xFE000000!!!
- mt_pll_init: Set pll frequency for 25M crystal
- RAM_CONSOLE preloader last status: 0x0 0x0 0x0 0x0 0x0 0x0
- [PMIC_WRAP]wrap_init pass,the return value=0.
- [pmic_init] Preloader Start..................
- [pmic_init] MT6380 CHIP Code, reg_val = 0, 1:E2 0:E3
- [pmic_init] Done...................
- Chip part number:7622B
- MT7622 Version: 1.2.8, (iPA)
- SSC OFF
- mt_pll_post_init: mt_get_cpu_freq = 1350000Khz
- mt_pll_post_init: mt_get_mem_freq = 1600000Khz
- mt_pll_post_init: mt_get_bus_freq = 279980Khz
- [PLFM] Init I2C: OK(0)
- [BLDR] Build Time: 20210316-161525
- ==== Dump RGU Reg ========
- RGU MODE: 14
- RGU LENGTH: FFE0
- RGU STA: 40000000
- RGU INTERVAL: FFF
- RGU SWSYSRST: 8000
- ==== Dump RGU Reg End ====
- RGU: g_rgu_satus:2
- mtk_wdt_mode_config mode value=10, tmp:22000010
- PL RGU RST: ??
- SW reset with bypass power key flag
- Find bypass powerkey flag
- WDT NONRST=0x20000000
- WDT IRQ_EN=0x300002
- RGU mtk_wdt_init:MTK_WDT_DEBUG_CTL(590200F3)
- [EMI] MDL number = 2
- [EMI] DRAMC calibration start
- [DDR] Gating glitch patched (0<cnt<=6)
- [EMI] DRAMC calibration end
- [EMI]rank size auto detect
- [EMI]start_addr[0x40000000]=0x12345678, test_addr[0x48000000]= 0xEDCBA987
- [EMI]start_addr[0x40000000]=0xEDCBA987, test_addr[0x50000000]= 0xEDCBA987
- [EMI]rank0 size: 0x10000000
- [MEM] complex R/W mem test pass
- RAM_CONSOLE wdt status (0x2)=0x2
- mtk_snand_get_device_info
- 2-Recognize NAND: ID [C8 51 ], Device Name [GD5F1GQ5UEYIG], Page Size [2048]B Spare Size [128]B Total Size [128]MB
- [BBT] BMT.v2 is found at 0x3FF
- [PLFM] Init Boot Device: OK(0)
- [PART] blksz: 2048B
- [PART] [0x0000000000000000-0x000000000007FFFF] "PRELOADER" (256 blocks)
- [PART] [0x0000000000080000-0x00000000000BFFFF] "tee1" (128 blocks)
- [PART] [0x00000000000C0000-0x000000000013FFFF] "lk" (256 blocks)
- Device APC domain init setup:
- Domain Setup (0x0)
- Domain Setup (0x0)
- Device APC domain after setup:
- Domain Setup (0x0)
- Domain Setup (0x0)
- [PART] Image with part header
- [PART] name : U-Boot
- [PART] addr : 41E00000h mode : -1
- [PART] size : 356560
- [PART] magic: 58881688h
- [PART] load "lk" from 0x00000000000C0200 (dev) to 0x41E00000 (mem) [SUCCESS]
- [PART] load speed: 16581KB/s, 356560 bytes, 21ms
- load lk (ret=0)
- [PART] Image with part header
- [PART] name : atf
- [PART] addr : FFFFFFFFh mode : -1
- [PART] size : 57936
- [PART] magic: 58881688h
- [PART] load "tee1" from 0x0000000000080200 (dev) to 0x43000DC0 (mem) [SUCCESS]
- [PART] load speed: 14144KB/s, 57936 bytes, 4ms
- load tee1 (ret=0)
- [BLDR] bldr load tee part ret=0x0, addr=0x43001000
- [BLDR] boot part. not found
- [BLDR] part_load_images ret=0x0
- [BLDR] Others, jump to ATF
- [BLDR] jump to 0x41E00000
- [BLDR] <0x41E00000>=0xEA00000F
- [BLDR] <0x41E00004>=0xE59FF014
- U-Boot 2014.04-rc1 (Nov 12 2021 - 05:58:34)
- auto detection g_total_rank_size = 0x F000000
- DRAM: 240 MiB
- Turn on power orange!
- NAND: Recognize SNAND: ID [c8 51 ], Device Name [GD5F1GQ5UEYIG], Page Size [2048]B Spare Size [128]B Total Size [128]MB
- [mtk_snand] probe successfully!
- Not found in UBOOT NAND flash list
- [BBT] BMT.v2 is found at 0x3ff
- 128 MiB
- In: serial
- Out: serial
- Err: serial
- Net: mtk_eth
- Uip activated
- *** U-Boot SPI NAND ***
- 1. Load firmware 0 and bootup.
- 2. Load firmware 1 and bootup.
- 3. Load firmware selected by Xiaoqiang and bootup.
- U-Boot console
- trigger button release!
- Press UP/DOWN to move or Press 1~3 to choose, ENTER to select
- Erasing NAND...
- [mtk_nand_erase_hw] mtk_nand_erase_hw @4249, ret:0x40. page:0x280
- Erasing at 0x140000 -- 100% complete.
- Writing to NAND... OK
- Booting System 1
- NAND read: device 0 offset 0x2c0000, size 0x2000
- 8192 bytes read: OK
- [do_read_image_blks] This is a FIT image,img_size = 0x39750c
- [do_read_image_blks] img_blks = 0x72f
- [do_read_image_blks] img_align_size = 0x397800
- NAND read: device 0 offset 0x2c0000, size 0x397800
- 3766272 bytes read: OK
- bootm flag=0, states=70f
- ## Loading kernel from FIT Image at 4007ff28 ...
- Using 'config-1' configuration
- Trying 'kernel-1' kernel subimage
- Description: ARM64 OpenWrt Linux-5.10.138
- Type: Kernel Image
- Compression: lzma compressed
- Data Start: 0x40080014
- Data Size: 3734891 Bytes = 3.6 MiB
- Architecture: AArch64
- OS: Linux
- Load Address: 0x44000000
- Entry Point: 0x44000000
- Hash algo: crc32
- Hash value: 34277d02
- Hash algo: sha1
- Hash value: 59350071fab74c7ebc25527d129b8df03b928550
- Verifying Hash Integrity ... crc32+ sha1+ OK
- ## Loading fdt from FIT Image at 4007ff28 ...
- Using 'config-1' configuration
- Trying 'fdt-1' fdt subimage
- Description: ARM64 OpenWrt xiaomi_redmi-router-ax6s device tree blob
- Type: Flat Device Tree
- Compression: uncompressed
- Data Start: 0x4040fec8
- Data Size: 28699 Bytes = 28 KiB
- Architecture: AArch64
- Hash algo: crc32
- Hash value: 5266c96c
- Hash algo: sha1
- Hash value: 971ba76339e05a4af50e447c1c18ffe13e6b9242
- Verifying Hash Integrity ... crc32+ sha1+ OK
- Booting using the fdt blob at 0x4040fec8
- Uncompressing Kernel Image ... OK
- Loading Device Tree to 4cf39000, end 4cf4301a ... OK
- Starting kernel ...
- [ATF][ 7.834669]save kernel info
- [ATF][ 7.837606]Kernel_EL2
- [ATF][ 7.840276]Kernel is 64Bit
- [ATF][ 7.843364]pc=0x44000000, r0=0x4cf39000, r1=0x0
- INFO: BL3-1: Preparing for EL3 exit to normal world, Kernel
- INFO: BL3-1: Next image address = 0x44000000
- INFO: BL3-1: Next image spsr = 0x3c9
- [ATF][ 7.861062]el3_exit
- [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
- [ 0.000000] Linux version 5.10.138 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19685-512e76967f) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sat Sep 3 02:55:34 2022
- [ 0.000000] Machine model: Xiaomi Redmi Router AX6S
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA [mem 0x0000000040000000-0x000000004fffffff]
- [ 0.000000] DMA32 empty
- [ 0.000000] Normal empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
- [ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
- [ 0.000000] node 0: [mem 0x0000000043030000-0x000000004fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000004fffffff]
- [ 0.000000] On node 0 totalpages: 65536
- [ 0.000000] DMA zone: 1024 pages used for memmap
- [ 0.000000] DMA zone: 0 pages reserved
- [ 0.000000] DMA zone: 65536 pages, LIFO batch:15
- [ 0.000000] psci: probing for conduit method from DT.
- [ 0.000000] psci: PSCIv0.2 detected in firmware.
- [ 0.000000] psci: Using standard PSCI v0.2 function IDs
- [ 0.000000] psci: Trusted OS migration not required
- [ 0.000000] percpu: Embedded 20 pages/cpu s43992 r8192 d29736 u81920
- [ 0.000000] pcpu-alloc: s43992 r8192 d29736 u81920 alloc=20*4096
- [ 0.000000] pcpu-alloc: [0] 0 [0] 1
- [ 0.000000] Detected VIPT I-cache on CPU0
- [ 0.000000] CPU features: detected: ARM erratum 845719
- [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
- [ 0.000000] CPU features: detected: ARM erratum 843419
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64512
- [ 0.000000] Kernel command line: console=ttyS0,115200n1 loglevel=8 swiotlb=512 rootfstype=squashfs firmware=1 uart_en=1
- [ 0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
- [ 0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
- [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
- [ 0.000000] Memory: 232880K/262144K available (8254K kernel code, 894K rwdata, 1440K rodata, 448K init, 300K bss, 29264K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] rcu: Hierarchical RCU implementation.
- [ 0.000000] Tracing variant of Tasks RCU enabled.
- [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
- [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
- [ 0.000000] GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set
- [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
- [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
- [ 0.000003] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
- [ 0.000189] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000)
- [ 0.000199] pid_max: default: 32768 minimum: 301
- [ 0.000271] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
- [ 0.000278] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
- [ 0.001282] rcu: Hierarchical SRCU implementation.
- [ 0.001384] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
- [ 0.001571] smp: Bringing up secondary CPUs ...
- [ 0.001907] Detected VIPT I-cache on CPU1
- [ 0.001952] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
- [ 0.002012] smp: Brought up 1 node, 2 CPUs
- [ 0.002020] SMP: Total of 2 processors activated.
- [ 0.002025] CPU features: detected: 32-bit EL0 Support
- [ 0.002029] CPU features: detected: CRC32 instructions
- [ 0.002140] CPU: All CPU(s) started at EL2
- [ 0.002151] alternatives: patching kernel code
- [ 0.005400] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.005419] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
- [ 0.005502] pinctrl core: initialized pinctrl subsystem
- [ 0.006628] NET: Registered protocol family 16
- [ 0.006933] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
- [ 0.006957] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
- [ 0.006981] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
- [ 0.007247] thermal_sys: Registered thermal governor 'fair_share'
- [ 0.007250] thermal_sys: Registered thermal governor 'bang_bang'
- [ 0.007255] thermal_sys: Registered thermal governor 'step_wise'
- [ 0.007258] thermal_sys: Registered thermal governor 'user_space'
- [ 0.007480] ASID allocator initialised with 65536 entries
- [ 0.007914] pstore: Registered ramoops as persistent store backend
- [ 0.007920] ramoops: using 0x10000@0x42ff0000, ecc: 0
- [ 0.033761] cryptd: max_cpu_qlen set to 1000
- [ 0.035548] SCSI subsystem initialized
- [ 0.035674] libata version 3.00 loaded.
- [ 0.035828] usbcore: registered new interface driver usbfs
- [ 0.035856] usbcore: registered new interface driver hub
- [ 0.035880] usbcore: registered new device driver usb
- [ 0.036923] clocksource: Switched to clocksource arch_sys_counter
- [ 0.037463] NET: Registered protocol family 2
- [ 0.037565] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
- [ 0.037913] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
- [ 0.037929] TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear)
- [ 0.037947] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear)
- [ 0.037975] TCP: Hash tables configured (established 2048 bind 2048)
- [ 0.038040] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
- [ 0.038055] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
- [ 0.038138] NET: Registered protocol family 1
- [ 0.038157] PCI: CLS 0 bytes, default 64
- [ 0.040892] workingset: timestamp_bits=46 max_order=16 bucket_order=0
- [ 0.043423] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.043433] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.076236] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
- [ 0.080628] mt-pmic-pwrap 10001000.pwrap: unexpected interrupt int=0x1
- [ 0.095027] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.096881] printk: console [ttyS0] disabled
- [ 0.117123] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 21, base_baud = 1562500) is a ST16650V2
- [ 0.709875] printk: console [ttyS0] enabled
- [ 0.714993] mtk_rng 1020f000.rng: registered RNG driver
- [ 0.715158] random: crng init done
- [ 0.720424] cacheinfo: Unable to detect cache hierarchy for CPU 0
- [ 0.732008] loop: module loaded
- [ 0.735152] Loading iSCSI transport class v2.0-870.
- [ 0.741193] mtk-snand 1100d000.snfi: chip is GD5F1GQ5xExxG, size 128MB, page size 2048, oob size 128
- [ 0.754285] [BBT] BMT.v2 is found at 0x3fe
- [ 0.758585] 10 fixed-partitions partitions found on MTD device 1100d000.snfi
- [ 0.765624] Creating 10 MTD partitions on "1100d000.snfi":
- [ 0.771125] 0x000000000000-0x000000080000 : "Preloader"
- [ 0.777537] 0x000000080000-0x0000000c0000 : "ATF"
- [ 0.782901] 0x0000000c0000-0x000000140000 : "u-boot"
- [ 0.788952] 0x000000140000-0x000000180000 : "u-boot-env"
- [ 0.794906] 0x000000180000-0x0000001c0000 : "bdata"
- [ 0.800452] 0x0000001c0000-0x000000240000 : "factory"
- [ 0.806585] 0x000000240000-0x000000280000 : "crash"
- [ 0.812147] 0x000000280000-0x0000002c0000 : "crash_log"
- [ 0.818042] 0x0000002c0000-0x0000006c0000 : "kernel"
- [ 0.831097] 2 fit-fw partitions found on MTD device kernel
- [ 0.836574] Creating 2 MTD partitions on "kernel":
- [ 0.841374] 0x000000000000-0x0000003a0000 : "kernel"
- [ 0.852690] 0x0000003e0000-0x000000400000 : "rootfs"
- [ 0.858102] mtd: device 10 (rootfs) set to be root filesystem
- [ 0.864068] mtdsplit: no squashfs found in "rootfs"
- [ 0.868957] 0x0000006c0000-0x0000075c0000 : "ubi"
- [ 1.112287] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc011c80000, irq 30
- [ 1.121864] i2c /dev entries driver
- [ 1.126279] mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
- [ 1.136980] NET: Registered protocol family 10
- [ 1.142061] Segment Routing with IPv6
- [ 1.145755] NET: Registered protocol family 17
- [ 1.150233] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
- [ 1.163396] 8021q: 802.1Q VLAN Support v1.8
- [ 1.168875] pstore: Using crash dump compression: deflate
- [ 1.183162] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges:
- [ 1.189729] mtk-pcie 1a143000.pcie: Parsing ranges property...
- [ 1.195560] mtk-pcie 1a143000.pcie: MEM 0x0020000000..0x0027ffffff -> 0x0020000000
- [ 1.220095] mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00
- [ 1.226270] pci_bus 0000:00: root bus resource [bus 00-ff]
- [ 1.231759] pci_bus 0000:00: root bus resource [mem 0x20000000-0x27ffffff]
- [ 1.238631] pci_bus 0000:00: scanning bus
- [ 1.242674] pci 0000:00:00.0: [14c3:3258] type 01 class 0x060400
- [ 1.248708] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x1ffffffff 64bit pref]
- [ 1.257373] pci_bus 0000:00: fixups for bus
- [ 1.261552] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0
- [ 1.268252] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
- [ 1.276257] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1
- [ 1.283044] pci_bus 0000:01: scanning bus
- [ 1.287261] pci 0000:01:00.0: [14c3:7915] type 00 class 0x000280
- [ 1.293436] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
- [ 1.300759] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
- [ 1.308086] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
- [ 1.316037] pci 0000:01:00.0: supports D1 D2
- [ 1.320303] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
- [ 1.326935] pci 0000:01:00.0: PME# disabled
- [ 1.331415] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
- [ 1.368077] pci_bus 0000:01: fixups for bus
- [ 1.372253] pci_bus 0000:01: bus scan returning with max=01
- [ 1.377833] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
- [ 1.384442] pci_bus 0000:00: bus scan returning with max=01
- [ 1.390025] pci 0000:00:00.0: BAR 0: no space for [mem size 0x200000000 64bit pref]
- [ 1.397677] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x200000000 64bit pref]
- [ 1.405672] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
- [ 1.412459] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref]
- [ 1.420281] pci 0000:01:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref]
- [ 1.428105] pci 0000:01:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref]
- [ 1.435923] pci 0000:00:00.0: PCI bridge to [bus 01]
- [ 1.440889] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff]
- [ 1.447745] pcieport 0000:00:00.0: of_irq_parse_pci: failed with rc=-22
- [ 1.454350] pcieport 0000:00:00.0: assign IRQ: got 0
- [ 1.459321] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
- [ 1.465422] pcieport 0000:00:00.0: enabling bus mastering
- [ 1.471248] mtk_hsdma 1b007000.dma-controller: Using 3 as missing dma-requests property
- [ 1.479451] mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered
- [ 1.534680] mt7530 mdio-bus:00 wan (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=138)
- [ 1.554293] mt7530 mdio-bus:00 lan1 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=139)
- [ 1.573920] mt7530 mdio-bus:00 lan2 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=140)
- [ 1.593543] mt7530 mdio-bus:00 lan3 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=141)
- [ 1.605131] mt7530 mdio-bus:00: configuring for fixed/2500base-x link mode
- [ 1.612169] DSA: tree 0 setup
- [ 1.612365] mt7530 mdio-bus:00: Link is Up - 2.5Gbps/Full - flow control rx/tx
- [ 1.615867] UBI: auto-attach mtd11
- [ 1.625753] ubi0: attaching mtd11
- [ 1.657505] UBI: EOF marker found, PEBs from 43 will be erased
- [ 1.843228] ubi0: scanning is finished
- [ 1.877175] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 824 LEBs
- [ 1.884016] ubi0: attached mtd11 (name "ubi", size 111 MiB)
- [ 1.889590] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- [ 1.896455] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- [ 1.903239] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
- [ 1.910198] ubi0: good PEBs: 888, bad PEBs: 0, corrupted PEBs: 0
- [ 1.916195] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
- [ 1.923412] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1662173734
- [ 1.932539] ubi0: available PEBs: 0, total reserved PEBs: 888, PEBs reserved for bad PEB handling: 19
- [ 1.941801] ubi0: background thread "ubi_bgt0d" started, PID 773
- [ 1.948954] block ubiblock0_0: created from ubi0:0(rootfs)
- [ 1.961033] List of all partitions:
- [ 1.964532] 1f00 512 mtdblock0
- [ 1.964534] (driver?)
- [ 1.971087] 1f04 256 mtdblock1
- [ 1.971089] (driver?)
- [ 1.977619] 1f08 512 mtdblock2
- [ 1.977621] (driver?)
- [ 1.984144] 1f0c 256 mtdblock3
- [ 1.984146] (driver?)
- [ 1.990678] 1f10 256 mtdblock4
- [ 1.990679] (driver?)
- [ 1.997207] 1f14 512 mtdblock5
- [ 1.997209] (driver?)
- [ 2.003733] 1f18 256 mtdblock6
- [ 2.003734] (driver?)
- [ 2.010265] 1f1c 256 mtdblock7
- [ 2.010266] (driver?)
- [ 2.016788] 1f20 4096 mtdblock8
- [ 2.016790] (driver?)
- [ 2.023320] 1f24 3712 mtdblock9
- [ 2.023322] (driver?)
- [ 2.029850] 1f28 128 mtdblock10
- [ 2.029852] (driver?)
- [ 2.036461] 1f2c 113664 mtdblock11
- [ 2.036463] (driver?)
- [ 2.043079] 103:00000 5084 ubiblock0_0
- [ 2.043080] (driver?)
- [ 2.049782] No filesystem could mount root, tried:
- [ 2.049785] squashfs
- [ 2.054652]
- [ 2.058402] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,40)
- [ 2.066831] SMP: stopping secondary CPUs
- [ 2.070746] Kernel Offset: disabled
- [ 2.074225] CPU features: 0x0000002,04002004
- [ 2.078483] Memory Limit: none
- [ 2.084713] Rebooting in 1 seconds..
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement