API tools faq
paste
Advertisement
WiredLuddite

Wise Tiger RT-8501 TFTP Boot Log

WiredLuddite
Dec 30th, 2020
44
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 14.64 KB | None | 0 0
raw download clone embed print report
  1. U-Boot 1.1.3 (Aug 1 2017 - 14:19:32)
  2.  
  3. Board: Ralink APSoC DRAM: 64 MB
  4. relocate_code Pointer at: 83fb8000
  5. enable ephy clock...done. rf reg 29 = 5
  6. SSC disabled.
  7. spi_wait_nsec: 29
  8. spi device id: c2 20 17 c2 20 (2017c220)
  9. find flash: MX25L6405D
  10. raspi_read: from:30000 len:1000
  11. raspi_read: from:30000 len:1000
  12. ============================================
  13. Ralink UBoot Version: 5.0.0.0
  14. --------------------------------------------
  15. ASIC 7620_MP (Port5<->None)
  16. DRAM component: 512 Mbits DDR, width 16
  17. DRAM bus: 16 bit
  18. Total memory: 64 MBytes
  19. Flash component: SPI Flash
  20. Date:Aug 1 2017 Time:14:19:32
  21. ============================================
  22. icache: sets:512, ways:4, linesz:32 ,total:65536
  23. dcache: sets:256, ways:4, linesz:32 ,total:32768
  24.  
  25. ##### The CPU freq = 580 MHZ ####
  26. estimate memory size =64 Mbytes
  27.  
  28. Please choose the operation:
  29. 1: Load system code to SDRAM via TFTP.
  30. 2: Load system code then write to Flash via TFTP.
  31. 3: Boot system code via Flash (default).
  32. 4: Entr boot command line interface.
  33. 7: Load Boot Loader code then write to Flash via Serial.
  34. 9: Load Boot Loader code then write to Flash via TFTP.
  35.  
  36. You choosed 1
  37. 0
  38. raspi_read: from:40028 len:6
  39.  
  40.  
  41. 1: System Load Linux to SDRAM via TFTP.
  42. Please Input new ones /or Ctrl-C to discard
  43. Input device IP (192.168.9.233) ==:192.168.9.233
  44. Input server IP (192.168.9.234) ==:192.168.9.234
  45. Input Linux Kernel filename (test-openwrt.bin) ==:test-openwrt.bin
  46.  
  47. NetTxPacket = 0x83FE5D80
  48.  
  49. KSEG1ADDR(NetTxPacket) = 0xA3FE5D80
  50.  
  51. NetLoop,call eth_halt !
  52.  
  53. NetLoop,call eth_init !
  54. Trying Eth0 (10/100-M)
  55.  
  56. Waitting for RX_DMA_BUSY status Start... done
  57.  
  58.  
  59. ETH_STATE_ACTIVE!!
  60. TFTP from server 192.168.9.234; our IP address is 192.168.9.233
  61. Filename 'test-openwrt.bin'.
  62.  
  63. TIMEOUT_COUNT=10,Load address: 0x80a00000
  64. Loading: Got ARP REPLY, set server/gtwy eth addr (54:e1:ad:fb:10:bb)
  65. Got it
  66. #################################################################
  67. ####################################################checksum bad
  68. checksum bad
  69. checksum bad
  70. checksum bad
  71. #############
  72. #################################################################
  73. #################################################################
  74. ####checksum bad
  75. #############################################################
  76. #################################################################
  77. #################################################################
  78. #################################################################
  79. #################################################################
  80. #################################################################
  81. #################################################################
  82. #################################################################
  83. #################################################################
  84. #################################################################
  85. ########################################################
  86. done
  87. Bytes transferred = 4941058 (4b6502 hex)
  88. LoadAddr=80a00000 NetBootFileXferSize= 004b6502
  89. Automatic boot of image at addr 0x80A00000 ...
  90. ## Booting image at 80a00000 ...
  91. Image Name: MIPS OpenWrt Linux-5.4.85
  92. Image Type: MIPS Linux Kernel Image (lzma compressed)
  93. Data Size: 4940994 Bytes = 4.7 MB
  94. Load Address: 80000000
  95. Entry Point: 80000000
  96. Verifying Checksum ... OK
  97. Uncompressing Kernel Image ... OK
  98. No initrd
  99. ## Transferring control to Linux (at address 80000000) ...
  100. ## Giving linux memsize in MB, 64
  101.  
  102. Starting kernel ...
  103.  
  104. [ 0.000000] Linux version 5.4.85 (zero@blackbox) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r15369-75900a25ed)) #0 Mon Dec 28 23:03:26 2020
  105. [ 0.000000] Board has DDR2
  106. [ 0.000000] Analog PMU set to hw control
  107. [ 0.000000] Digital PMU set to hw control
  108. [ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
  109. [ 0.000000] printk: bootconsole [early0] enabled
  110. [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
  111. [ 0.000000] MIPS: machine is Wise Tiger RT-8501
  112. [ 0.000000] Initrd not found or empty - disabling initrd
  113. [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  114. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  115. [ 0.000000] Zone ranges:
  116. [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
  117. [ 0.000000] Movable zone start for each node
  118. [ 0.000000] Early memory node ranges
  119. [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
  120. [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
  121. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
  122. [ 0.000000] Kernel command line: console=ttyS1,57600 rootfstype=squashfs,jffs2
  123. [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
  124. [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
  125. [ 0.000000] Writing ErrCtl register=0001bb2e
  126. [ 0.000000] Readback ErrCtl register=0001bb2e
  127. [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
  128. [ 0.000000] Memory: 54624K/65536K available (4701K kernel code, 203K rwdata, 1040K rodata, 4032K init, 205K bss, 10912K reserved, 0K cma-reserved)
  129. [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  130. [ 0.000000] NR_IRQS: 256
  131. [ 0.000000] random: get_random_bytes called from start_kernel+0x32c/0x520 with crng_init=0
  132. [ 0.000000] CPU Clock: 580MHz
  133. [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
  134. [ 0.000000] systick: enable autosleep mode
  135. [ 0.000000] systick: running - mult: 214748, shift: 32
  136. [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
  137. [ 0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
  138. [ 0.015475] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
  139. [ 0.059570] pid_max: default: 32768 minimum: 301
  140. [ 0.068961] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
  141. [ 0.083372] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
  142. [ 0.105645] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
  143. [ 0.124954] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
  144. [ 0.138555] pinctrl core: initialized pinctrl subsystem
  145. [ 0.149453] NET: Registered protocol family 16
  146. [ 0.420508] PCI host bridge /pcie@10140000 ranges:
  147. [ 0.429908] MEM 0x0000000020000000..0x000000002fffffff
  148. [ 0.440276] IO 0x0000000010160000..0x000000001016ffff
  149. [ 0.473561] rt2880_gpio 10000600.gpio: registering 24 gpios
  150. [ 0.484624] rt2880_gpio 10000600.gpio: registering 24 irq handlers
  151. [ 0.497667] PCI host bridge to bus 0000:00
  152. [ 0.505720] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
  153. [ 0.519337] pci_bus 0000:00: root bus resource [io 0xffffffff]
  154. [ 0.531108] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
  155. [ 0.544606] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
  156. [ 0.560401] pci 0000:00:00.0: [1814:0801] type 01 class 0x060400
  157. [ 0.572332] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
  158. [ 0.584767] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
  159. [ 0.597308] pci 0000:00:00.0: supports D1
  160. [ 0.605185] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
  161. [ 0.618701] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  162. [ 0.634737] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
  163. [ 0.646636] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
  164. [ 0.660089] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
  165. [ 0.673492] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
  166. [ 0.687538] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
  167. [ 0.700590] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
  168. [ 0.713741] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
  169. [ 0.726862] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
  170. [ 0.740711] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
  171. [ 0.754211] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
  172. [ 0.768576] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
  173. [ 0.782086] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
  174. [ 0.796633] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
  175. [ 0.810976] pci 0000:00:00.0: PCI bridge to [bus 01]
  176. [ 0.820845] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
  177. [ 0.834340] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
  178. [ 0.848820] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
  179. [ 0.872550] clocksource: Switched to clocksource systick
  180. [ 0.884406] NET: Registered protocol family 2
  181. [ 0.893871] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
  182. [ 0.910447] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
  183. [ 0.925607] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
  184. [ 0.939619] TCP: Hash tables configured (established 1024 bind 1024)
  185. [ 0.952400] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
  186. [ 0.965312] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
  187. [ 0.979450] NET: Registered protocol family 1
  188. [ 0.988079] PCI: CLS 0 bytes, default 32
  189. [ 1.484530] random: fast init done
  190. [ 6.550087] rt-timer 10000100.timer: maximum frequency is 1220Hz
  191. [ 6.564089] workingset: timestamp_bits=14 max_order=14 bucket_order=0
  192. [ 6.585314] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  193. [ 6.596822] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  194. [ 6.633859] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
  195. [ 6.647503] 10000500.uart: ttyS0 at MMIO 0x10000500 (irq = 13, base_baud = 2500000) is a Palmchip BK-3103
  196. [ 6.667240] 10000c00.uartlite: ttyS1 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
  197. [ 6.686945] printk: console [ttyS1] enabled
  198. [ 6.686945] printk: console [ttyS1] enabled
  199. [ 6.703459] printk: bootconsole [early0] disabled
  200. [ 6.703459] printk: bootconsole [early0] disabled
  201. [ 6.728847] spi spi0.0: force spi mode3
  202. [ 6.737487] spi-nor spi0.0: mx25l6405d (8192 Kbytes)
  203. [ 6.747522] 5 fixed-partitions partitions found on MTD device spi0.0
  204. [ 6.760195] Creating 5 MTD partitions on "spi0.0":
  205. [ 6.769755] 0x000000000000-0x000000030000 : "Bootloader"
  206. [ 6.781454] 0x000000030000-0x000000040000 : "Config"
  207. [ 6.792420] 0x000000040000-0x000000050000 : "Factory"
  208. [ 6.803544] 0x000000050000-0x000000060000 : "params"
  209. [ 6.814509] 0x000000060000-0x000000800000 : "firmware"
  210. [ 6.826684] libphy: Fixed MDIO Bus: probed
  211. [ 6.847160] gsw: setting port4 to ephy mode
  212. [ 6.855595] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 1 link up (100Mbps/Full duplex)
  213. [ 6.873791] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 3 link up (100Mbps/Full duplex)
  214. [ 6.892071] mtk_soc_eth 10100000.ethernet: generated random MAC address be:dd:d1:e5:9b:6d
  215. [ 6.908620] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
  216. [ 6.921170] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
  217. [ 6.938192] rt2880_wdt 10000120.watchdog: Initialized
  218. [ 6.949763] NET: Registered protocol family 10
  219. [ 6.962725] Segment Routing with IPv6
  220. [ 6.970246] NET: Registered protocol family 17
  221. [ 6.979196] 8021q: 802.1Q VLAN Support v1.8
  222. [ 7.011986] Freeing unused kernel memory: 4032K
  223. [ 7.021047] This architecture does not have kernel memory protection.
  224. [ 7.033880] Run /init as init process
  225. [ 7.613880] init: Console is alive
  226. [ 7.621087] init: - watchdog -
  227. [ 7.652825] kmodloader: loading kernel modules from /etc/modules-boot.d/*
  228. [ 7.672627] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
  229. [ 7.689957] init: - preinit -
  230. [ 7.952251] random: jshn: uninitialized urandom read (4 bytes read)
  231. [ 8.051906] random: jshn: uninitialized urandom read (4 bytes read)
  232. [ 8.087139] random: jshn: uninitialized urandom read (4 bytes read)
  233. [ 8.297012] 8021q: adding VLAN 0 to HW filter on device eth0
  234. Press the [f] key and hit [enter] to enter failsafe mode
  235. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  236. [ 8.902057] procd: - early -
  237. [ 8.908016] procd: - watchdog -
  238. [ 9.024848] procd: - watchdog -
  239. [ 9.031630] procd: - ubus -
  240. [ 9.047207] urandom_read: 6 callbacks suppressed
  241. [ 9.047217] random: ubusd: uninitialized urandom read (4 bytes read)
  242. [ 9.074207] procd: - init -
  243. Please press Enter to activate this console.
  244. [ 9.765087] kmodloader: loading kernel modules from /etc/modules.d/*
  245. [ 9.827593] Loading modules backported from Linux version v5.8.18-0-gab435ce49bd1
  246. [ 9.842595] Backport generated by backports.git v5.8.18-1-0-ga630fd46
  247. [ 9.930705] xt_time: kernel timezone is -0000
  248. [ 10.110054] PPP generic driver version 2.4.2
  249. [ 10.132119] NET: Registered protocol family 24
  250. [ 10.236009] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
  251. [ 10.258552] urngd: jent-rng init failed, err: 2
  252. [ 10.268734] rt2800_wmac 10180000.wmac: Direct firmware load for soc_wmac.eeprom failed with error -2
  253. [ 10.287014] rt2800_wmac 10180000.wmac: Falling back to sysfs fallback for: soc_wmac.eeprom
  254. [ 10.379380] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to request EEPROM.
  255. [ 10.396336] rt2800_wmac: probe of 10180000.wmac failed with error -12
  256. [ 10.436849] kmodloader: done loading kernel modules from /etc/modules.d/*
  257. [ 15.718100] random: crng init done
  258.  
  259.  
  260.  
  261. BusyBox v1.31.1 () built-in shell (ash)
  262.  
  263. _______ ________ __
  264. | |.-----.-----.-----.| | | |.----.| |_
  265. | - || _ | -__| || | | || _|| _|
  266. |_______|| __|_____|__|__||________||__| |____|
  267. |__| W I R E L E S S F R E E D O M
  268. -----------------------------------------------------
  269. OpenWrt SNAPSHOT, r15369-75900a25ed
  270. -----------------------------------------------------
  271. === WARNING! =====================================
  272. There is no root password defined on this device!
  273. Use the "passwd" command to set up a new password
  274. in order to prevent unauthorized SSH logins.
  275. --------------------------------------------------
  276. root@OpenWrt:/#
  277.  
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!