Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 2017.09 (Sep 17 2021 - 11:59:28 +0000)
- Model: Pine64 RK3566 Quartz64 Board
- PreSerial: 2, raw, 0xfe660000
- DRAM: 2 GiB
- Sysmem: init
- Relocation Offset: 7d39f000, fdt: 7b9f9fb8
- no mmc device at slot 1
- dwmmc@fe2b0000: 1 (SD), dwmmc@fe2c0000: 2, sdhci@fe310000: 0
- Bootdev(atags): mmc 1
- MMC1: Legacy, 50Mhz
- PartType: EFI
- No misc partition
- boot mode: None
- FIT: No fdt blob
- No resource partition
- Failed to load DTB
- Failed to get kernel dtb, ret=-19
- io-domain: OK
- ** Unable to use mmc 1:3 for loading the env **
- Using default environment
- Model: Pine64 RK3566 Quartz64 Board
- rockchip_set_serialno: could not find efuse/otp device
- CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
- apll 816000 KHz
- dpll 528000 KHz
- gpll 1188000 KHz
- cpll 1000000 KHz
- npll 24000 KHz
- vpll 24000 KHz
- hpll 24000 KHz
- ppll 100000 KHz
- armclk 816000 KHz
- aclk_bus 150000 KHz
- pclk_bus 50000 KHz
- aclk_top_high 300000 KHz
- aclk_top_low 200000 KHz
- hclk_top 150000 KHz
- pclk_top 50000 KHz
- aclk_perimid 300000 KHz
- hclk_perimid 150000 KHz
- pclk_pmu 50000 KHz
- Net: clk_get_by_name(master_bus) failed: -22eqos_probe_resources() failed: -22No ethernet found.
- Hit key to stop autoboot('CTRL+C'): 0
- ## Booting FIT Image FIT: No fit blob
- FIT: No FIT image
- Could not find misc partition
- ANDROID: reboot reason: "(none)"
- optee api revision: 2.0
- TEEC: Waring: Could not find security partition
- Not AVB images, AVB skip
- No valid android hdr
- Android image load failed
- Android boot failed, error -1.
- switch to partitions #0, OK
- mmc1 is current device
- Scanning mmc 1:2...
- Found /extlinux/extlinux.conf
- Retrieving file: /extlinux/extlinux.conf
- reading /extlinux/extlinux.conf
- 353 bytes read in 4 ms (85.9 KiB/s)
- Select the boot mode
- 1: linux
- Enter choice: 1: linux
- Retrieving file: /rootfs.cpio.lz4
- reading /rootfs.cpio.lz4
- 20469711 bytes read in 1747 ms (11.2 MiB/s)
- Retrieving file: /extlinux/Image_5.16
- reading /extlinux/Image_5.16
- 36026880 bytes read in 3074 ms (11.2 MiB/s)
- append: earlycon=uart8250,mmio32,0xfe660000 console=ttyS2,1500000n8
- Retrieving file: /extlinux/dtb_5.16
- reading /extlinux/dtb_5.16
- 45219 bytes read in 11 ms (3.9 MiB/s)
- Fdt Ramdisk skip relocation
- ## Flattened Device Tree blob at 0x0a100000
- Booting using the fdt blob at 0x0a100000
- Using Device Tree in place at 000000000a100000, end 000000000a10e0a2
- can't found rockchip,drm-logo, use rockchip,fb-logo
- WARNING: could not set reg FDT_ERR_BADOFFSET.
- failed to reserve fb-loader-logo memory
- Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
- Adding bank: 0x09400000 - 0x80000000 (size: 0x76c00000)
- Total: 7278.723 ms
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
- [ 0.000000] Linux version 5.16.0-rc4-r2pro-00027-g2980767edc50-dirty (frank@frank-G5-U20) (aarch64-linux-gnu-gcc (Ubuntu 9.3.0-171
- [ 0.000000] Machine model: Bananapi-R2 Pro (RK3568) DDR4 V00 Board
- [ 0.000000] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options '')
- [ 0.000000] printk: bootconsole [uart8250] enabled
- [ 0.000000] efi: UEFI not found.
- [ 0.000000] NUMA: No NUMA configuration found
- [ 0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x000000007fffffff]
- [ 0.000000] NUMA: NODE_DATA [mem 0x7fbc3a80-0x7fbc5fff]
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA [mem 0x0000000000200000-0x000000007fffffff]
- [ 0.000000] DMA32 empty
- [ 0.000000] Normal empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000200000-0x00000000083fffff]
- [ 0.000000] node 0: [mem 0x0000000009400000-0x000000007fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x000000007fffffff]
- [ 0.000000] On node 0, zone DMA: 512 pages in unavailable ranges
- [ 0.000000] On node 0, zone DMA: 4096 pages in unavailable ranges
- [ 0.000000] cma: Reserved 32 MiB at 0x000000007b800000
- [ 0.000000] psci: probing for conduit method from DT.
- [ 0.000000] psci: PSCIv1.1 detected in firmware.
- [ 0.000000] psci: Using standard PSCI v0.2 function IDs
- [ 0.000000] psci: Trusted OS migration not required
- [ 0.000000] psci: SMC Calling Convention v1.2
- [ 0.000000] percpu: Embedded 28 pages/cpu s74200 r8192 d32296 u114688
- [ 0.000000] pcpu-alloc: s74200 r8192 d32296 u114688 alloc=28*4096
- [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
- [ 0.000000] Detected VIPT I-cache on CPU0
- [ 0.000000] CPU features: detected: GIC system register CPU interface
- [ 0.000000] CPU features: detected: Virtualization Host Extensions
- [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
- [ 0.000000] alternatives: patching kernel code
- [ 0.000000] Fallback order for Node 0: 0
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 511496
- [ 0.000000] Policy zone: DMA
- [ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0xfe660000 console=ttyS2,1500000n8
- [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
- [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
- [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
- [ 0.000000] Memory: 1949440K/2078720K available (18496K kernel code, 3054K rwdata, 7476K rodata, 6016K init, 618K bss, 96512K res)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
- [ 0.000000] ftrace: allocating 60079 entries in 235 pages
- [ 0.000000] ftrace: allocated 235 pages with 6 groups
- [ 0.000000] trace event string verifier disabled
- [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
- [ 0.000000] rcu: RCU event tracing is enabled.
- [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
- [ 0.000000] Trampoline variant of Tasks RCU enabled.
- [ 0.000000] Rude variant of Tasks RCU enabled.
- [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
- [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
- [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
- [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
- [ 0.000000] GICv3: 320 SPIs implemented
- [ 0.000000] GICv3: 0 Extended SPIs implemented
- [ 0.000000] GICv3: Distributor has no Range Selector support
- [ 0.000000] GICv3: MBI range [296:319]
- [ 0.000000] GICv3: Using MBI frame 0x00000000fd410000
- [ 0.000000] Root IRQ handler: gic_handle_irq
- [ 0.000000] GICv3: 16 PPIs implemented
- [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
- [ 0.000000] ITS: No ITS available, not enabling LPIs
- [ 0.000000] random: get_random_bytes called from start_kernel+0x77c/0x968 with crng_init=0
- [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
- [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
- [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
- [ 0.001516] Console: colour dummy device 80x25
- [ 0.002081] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
- [ 0.003101] pid_max: default: 32768 minimum: 301
- [ 0.003672] LSM: Security Framework initializing
- [ 0.004220] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
- [ 0.004969] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
- [ 0.008674] rcu: Hierarchical SRCU implementation.
- [ 0.010204] EFI services will not be available.
- [ 0.011347] smp: Bringing up secondary CPUs ...
- I/TC: Secondary CPU 1 initializing
- I/TC: Secondary CPU 1 switching to normal world boot
- I/TC: Secondary CPU 2 initializing
- I/TC: Secondary CPU 2 switching to normal world boot
- I/TC: Secondary CPU 3 initializing
- I/TC: Secondary CPU 3 switching to normal world boot
- [ 0.013502] Detected VIPT I-cache on CPU1
- [ 0.013554] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
- [ 0.013629] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
- [ 0.015558] Detected VIPT I-cache on CPU2
- [ 0.015603] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
- [ 0.015656] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
- [ 0.017426] Detected VIPT I-cache on CPU3
- [ 0.017464] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000
- [ 0.017512] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
- [ 0.017701] smp: Brought up 1 node, 4 CPUs
- [ 0.023347] SMP: Total of 4 processors activated.
- [ 0.023818] CPU features: detected: 32-bit EL0 Support
- [ 0.024323] CPU features: detected: 32-bit EL1 Support
- [ 0.024830] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
- [ 0.025672] CPU features: detected: Common not Private translations
- [ 0.026313] CPU features: detected: CRC32 instructions
- [ 0.026825] CPU features: detected: RCpc load-acquire (LDAPR)
- [ 0.027390] CPU features: detected: LSE atomic instructions
- [ 0.027937] CPU features: detected: Privileged Access Never
- [ 0.028484] CPU features: detected: RAS Extension Support
- [ 0.029016] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
- [ 0.072497] CPU: All CPU(s) started at EL2
- [ 0.075694] devtmpfs: initialized
- [ 0.088017] KASLR disabled due to lack of seed
- [ 0.088732] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
- [ 0.089710] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
- [ 0.091774] pinctrl core: initialized pinctrl subsystem
- [ 0.092854] regulator-dummy: no parameters, enabled
- [ 0.093578]
- [ 0.093736] *************************************************************
- [ 0.094402] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
- [ 0.095118] ** **
- [ 0.095787] ** IOMMU DebugFS SUPPORT HAS BEEN ENABLED IN THIS KERNEL **
- [ 0.096449] ** **
- [ 0.097113] ** This means that this kernel is built to expose internal **
- [ 0.097776] ** IOMMU data structures, which may compromise security on **
- [ 0.098439] ** your system. **
- [ 0.099102] ** **
- [ 0.099782] ** If you see this message and you are not debugging the **
- [ 0.100448] ** kernel, report this immediately to your vendor! **
- [ 0.101113] ** **
- [ 0.101775] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
- [ 0.102439] *************************************************************
- [ 0.103429] DMI not present or invalid.
- [ 0.104549] NET: Registered PF_NETLINK/PF_ROUTE protocol family
- [ 0.107634] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
- [ 0.108614] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
- [ 0.109666] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
- [ 0.110532] audit: initializing netlink subsys (disabled)
- [ 0.111329] audit: type=2000 audit(0.108:1): state=initialized audit_enabled=0 res=1
- [ 0.113368] thermal_sys: Registered thermal governor 'fair_share'
- [ 0.113382] thermal_sys: Registered thermal governor 'bang_bang'
- [ 0.113985] thermal_sys: Registered thermal governor 'step_wise'
- [ 0.114575] thermal_sys: Registered thermal governor 'user_space'
- [ 0.115165] thermal_sys: Registered thermal governor 'power_allocator'
- [ 0.116369] cpuidle: using governor menu
- [ 0.117687] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
- [ 0.118547] ASID allocator initialised with 65536 entries
- [ 0.119235] Serial: AMBA PL011 UART driver
- [ 0.150405] rockchip-gpio fdd60000.gpio: probed /pinctrl/gpio@fdd60000
- [ 0.151930] rockchip-gpio fe740000.gpio: probed /pinctrl/gpio@fe740000
- [ 0.153427] rockchip-gpio fe750000.gpio: probed /pinctrl/gpio@fe750000
- [ 0.154903] rockchip-gpio fe760000.gpio: probed /pinctrl/gpio@fe760000
- [ 0.156375] rockchip-gpio fe770000.gpio: probed /pinctrl/gpio@fe770000
- [ 0.184191] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
- [ 0.184875] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
- [ 0.185638] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
- [ 0.186301] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
- [ 0.187926] cryptd: max_cpu_qlen set to 1000
- [ 0.189893] ACPI: Interpreter disabled.
- [ 0.190897] dc_12v: 12000 mV, enabled
- [ 0.191479] reg-fixed-voltage dc-12v: dc_12v supplying 12000000uV
- [ 0.192322] vcc3v3_sys: will resolve supply early: vin
- [ 0.192838] reg-fixed-voltage vcc3v3-sys: Looking up vin-supply from device tree
- [ 0.193576] vcc3v3_sys: supplied by dc_12v
- [ 0.194086] dc_12v: could not add device link regulator.2: -ENOENT
- [ 0.194770] vcc3v3_sys: 3300 mV, enabled
- [ 0.195346] reg-fixed-voltage vcc3v3-sys: vcc3v3_sys supplying 3300000uV
- [ 0.196222] vcc5v0_sys: will resolve supply early: vin
- [ 0.196737] reg-fixed-voltage vcc5v0-sys: Looking up vin-supply from device tree
- [ 0.197474] vcc5v0_sys: supplied by dc_12v
- [ 0.197910] dc_12v: could not add device link regulator.3: -ENOENT
- [ 0.198586] vcc5v0_sys: 5000 mV, enabled
- [ 0.199167] reg-fixed-voltage vcc5v0-sys: vcc5v0_sys supplying 5000000uV
- [ 0.200047] vcc3v3_lcd0_n: no parameters, enabled
- [ 0.200721] reg-fixed-voltage vcc3v3-lcd0-n: vcc3v3_lcd0_n supplying 0uV
- [ 0.201611] vcc3v3_lcd1_n: no parameters, enabled
- [ 0.202281] reg-fixed-voltage vcc3v3-lcd1-n: vcc3v3_lcd1_n supplying 0uV
- [ 0.203590] iommu: Default domain type: Passthrough
- [ 0.205392] vgaarb: loaded
- [ 0.206058] SCSI subsystem initialized
- [ 0.206752] libata version 3.00 loaded.
- [ 0.207499] usbcore: registered new interface driver usbfs
- [ 0.208113] usbcore: registered new interface driver hub
- [ 0.208688] usbcore: registered new device driver usb
- [ 0.209856] pps_core: LinuxPPS API ver. 1 registered
- [ 0.210351] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- [ 0.211325] PTP clock support registered
- [ 0.211762] EDAC MC: Ver: 3.0.0
- [ 0.213250] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
- [ 0.213999] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
- [ 0.215786] Advanced Linux Sound Architecture Driver Initialized.
- [ 0.217299] Bluetooth: Core ver 2.22
- [ 0.217708] NET: Registered PF_BLUETOOTH protocol family
- [ 0.218235] Bluetooth: HCI device and connection manager initialized
- [ 0.218872] Bluetooth: HCI socket layer initialized
- [ 0.219397] Bluetooth: L2CAP socket layer initialized
- [ 0.219932] Bluetooth: SCO socket layer initialized
- [ 0.221331] clocksource: Switched to clocksource arch_sys_counter
- [ 0.317920] VFS: Disk quotas dquot_6.6.0
- [ 0.318409] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
- [ 0.319751] pnp: PnP ACPI: disabled
- [ 0.333642] NET: Registered PF_INET protocol family
- [ 0.334372] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
- [ 0.336664] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
- [ 0.337644] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
- [ 0.338565] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear)
- [ 0.339542] TCP: Hash tables configured (established 16384 bind 16384)
- [ 0.340342] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
- [ 0.341050] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
- [ 0.342029] NET: Registered PF_UNIX/PF_LOCAL protocol family
- [ 0.343208] RPC: Registered named UNIX socket transport module.
- [ 0.343798] RPC: Registered udp transport module.
- [ 0.344262] RPC: Registered tcp transport module.
- [ 0.344726] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 0.346431] PCI: CLS 0 bytes, default 64
- [ 0.347159] Trying to unpack rootfs image as initramfs...
- [ 0.358619] hw perfevents: enabled with armv8_cortex_a55 PMU driver, 7 counters available
- [ 0.360209] kvm [1]: IPA Size Limit: 40 bits
- [ 0.360686] kvm [1]: GICv3: no GICV resource entry
- [ 0.361168] kvm [1]: disabling GICv2 emulation
- [ 0.361689] kvm [1]: GIC system register CPU interface enabled
- [ 0.362587] kvm [1]: vgic interrupt IRQ9
- [ 0.363337] kvm [1]: VHE mode initialized successfully
- [ 0.367902] Initialise system trusted keyrings
- [ 0.368834] workingset: timestamp_bits=42 max_order=19 bucket_order=0
- [ 0.380473] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.382428] NFS: Registering the id_resolver key type
- [ 0.382990] Key type id_resolver registered
- [ 0.383410] Key type id_legacy registered
- [ 0.384010] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
- [ 0.384688] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
- [ 0.386026] ksmbd: The ksmbd server is experimental, use at your own risk.
- [ 0.386722] ntfs3: Max link count 4000
- [ 0.387093] ntfs3: Read-only LZX/Xpress compression included
- [ 0.388223] 9p: Installing v9fs 9p2000 file system support
- [ 0.442707] Key type asymmetric registered
- [ 0.443152] Asymmetric key parser 'x509' registered
- [ 0.443939] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
- [ 0.444686] io scheduler mq-deadline registered
- [ 0.445140] io scheduler kyber registered
- [ 0.453913] EINJ: ACPI disabled.
- [ 0.462017] dma-pl330 fe530000.dmac: Loaded driver for PL330 DMAC-241330
- [ 0.462711] dma-pl330 fe530000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
- [ 0.466922] dma-pl330 fe550000.dmac: Loaded driver for PL330 DMAC-241330
- [ 0.467615] dma-pl330 fe550000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
- [ 0.470711] arm-scmi firmware:scmi: Failed. SCMI protocol 22 not active.
- [ 0.477059] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
- [ 0.481718] printk: console [ttyS2] disabled
- [ 0.482272] fe660000.serial: ttyS2 at MMIO 0xfe660000 (irq = 30, base_baud = 1500000) is a 16550A
- [ 0.483508] printk: console [ttyS2] enabled
- [ 0.483508] printk: console [ttyS2] enabled
- [ 0.484306] printk: bootconsole [uart8250] disabled
- [ 0.484306] printk: bootconsole [uart8250] disabled
- [ 0.491217] cacheinfo: Unable to detect cache hierarchy for CPU 0
- [ 0.504874] brd: module loaded
- [ 0.515072] loop: module loaded
- [ 0.516293] zram: Added device: zram0
- [ 0.516900] megasas: 07.719.03.00-rc1
- [ 0.521697] SPI driver mtd_dataflash has no spi_device_id for atmel,at45
- [ 0.522317] SPI driver mtd_dataflash has no spi_device_id for atmel,dataflash
- [ 0.525993] libphy: Fixed MDIO Bus: probed
- [ 0.528990] tun: Universal TUN/TAP device driver, 1.6
- [ 0.529955] e100: Intel(R) PRO/100 Network Driver
- [ 0.530392] e100: Copyright(c) 1999-2006 Intel Corporation
- [ 0.530977] e1000: Intel(R) PRO/1000 Network Driver
- [ 0.531418] e1000: Copyright (c) 1999-2006 Intel Corporation.
- [ 0.532056] e1000e: Intel(R) PRO/1000 Network Driver
- [ 0.532504] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
- [ 0.533119] igb: Intel(R) Gigabit Ethernet Network Driver
- [ 0.533654] igb: Copyright (c) 2007-2014 Intel Corporation.
- [ 0.534272] Intel(R) 2.5G Ethernet Linux Driver
- [ 0.534681] Copyright(c) 2018 Intel Corporation.
- [ 0.535173] igbvf: Intel(R) Gigabit Virtual Function Network Driver
- [ 0.535730] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
- [ 0.536336] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver
- [ 0.536882] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
- [ 0.537983] ixgbevf: Intel(R) 10 Gigabit PCI Express Virtual Function Network Driver
- [ 0.538690] ixgbevf: Copyright (c) 2009 - 2018 Intel Corporation.
- [ 0.539761] i40e: Intel(R) Ethernet Connection XL710 Network Driver
- [ 0.540339] i40e: Copyright (c) 2013 - 2019 Intel Corporation.
- [ 0.541422] ixgb: Intel(R) PRO/10GbE Network Driver
- [ 0.541877] ixgb: Copyright (c) 1999-2008 Intel Corporation.
- [ 0.542507] iavf: Intel(R) Ethernet Adaptive Virtual Function Network Driver
- [ 0.543139] Copyright (c) 2013 - 2018 Intel Corporation.
- [ 0.544112] Intel(R) Ethernet Switch Host Interface Driver
- [ 0.544618] Copyright(c) 2013 - 2019 Intel Corporation.
- [ 0.545577] ice: Intel(R) Ethernet Connection E800 Series Linux Driver
- [ 0.546174] ice: Copyright (c) 2018, Intel Corporation.
- [ 0.548599] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found
- [ 0.549545] rk_gmac-dwmac fe010000.ethernet: Looking up phy-supply from device tree
- [ 0.550262] rk_gmac-dwmac fe010000.ethernet: Looking up phy-supply property in node /ethernet@fe010000 failed
- [ 0.551182] rk_gmac-dwmac fe010000.ethernet: no regulator found
- [ 0.551718] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output).
- [ 0.552358] rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay.
- [ 0.552992] rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30
- [ 0.553608] rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay.
- [ 0.554254] rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10
- [ 0.554817] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
- [ 0.560490] rk_gmac-dwmac fe010000.ethernet: init for RGMII_ID
- [ 0.561626] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51
- [ 0.562304] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5
- [ 0.562771] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register supported
- [ 0.563437] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine supported
- [ 0.564100] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported
- [ 0.564722] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported
- [ 0.565497] rk_gmac-dwmac fe010000.ethernet: TSO supported
- [ 0.566005] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watchdog Timer
- [ 0.566725] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled
- [ 0.567265] rk_gmac-dwmac fe010000.ethernet: Using 32 bits DMA width
- [ 0.568591] libphy: stmmac: probed
- [ 0.571892] rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found
- [ 0.572739] rk_gmac-dwmac fe2a0000.ethernet: Looking up phy-supply from device tree
- [ 0.573493] rk_gmac-dwmac fe2a0000.ethernet: Looking up phy-supply property in node /ethernet@fe2a0000 failed
- [ 0.574418] rk_gmac-dwmac fe2a0000.ethernet: no regulator found
- [ 0.574954] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (output).
- [ 0.575592] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay.
- [ 0.576224] rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0x30
- [ 0.576770] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay.
- [ 0.577432] rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0x10
- [ 0.578000] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no).
- [ 0.583662] rk_gmac-dwmac fe2a0000.ethernet: init for RGMII_ID
- [ 0.584682] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51
- [ 0.585388] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5
- [ 0.585857] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register supported
- [ 0.586522] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine supported
- [ 0.587184] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported
- [ 0.587807] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported
- [ 0.588513] rk_gmac-dwmac fe2a0000.ethernet: TSO supported
- [ 0.589012] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
- [ 0.589813] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled
- [ 0.590360] rk_gmac-dwmac fe2a0000.ethernet: Using 32 bits DMA width
- [ 0.591672] libphy: stmmac: probed
- [ 0.592325] mdio_bus stmmac-0: MDIO device at address 0 is missing.
- [ 0.595770] usbcore: registered new interface driver rtl8192cu
- [ 0.596846] usbcore: registered new interface driver rtl8xxxu
- [ 0.597698] usbcore: registered new interface driver ax88179_178a
- [ 0.598661] VFIO - User Level meta-driver version: 0.3
- [ 0.601260] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 0.601923] ehci-pci: EHCI PCI platform driver
- [ 0.602491] ehci-platform: EHCI generic platform driver
- [ 0.603344] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 0.603943] ohci-pci: OHCI PCI platform driver
- [ 0.604493] ohci-platform: OHCI generic platform driver
- [ 0.606202] usbcore: registered new interface driver usb-storage
- [ 0.608157] i2c_dev: i2c /dev entries driver
- [ 0.612793] rk808 0-0020: chip id: 0x8090
- [ 0.654545] random: fast init done
- [ 0.694557] rk808-regulator rk808-regulator: there is no dvs0 gpio
- [ 0.695162] rk808-regulator rk808-regulator: there is no dvs1 gpio
- [ 0.698345] vdd_logic: will resolve supply early: vcc1
- [ 0.698845] rk808 0-0020: Looking up vcc1-supply from device tree
- [ 0.699416] vdd_logic: supplied by vcc3v3_sys
- [ 0.699824] vcc3v3_sys: could not add device link regulator.6: -ENOENT
- [ 0.704403] vdd_logic: 500 <--> 1350 mV at 900 mV, enabled
- [ 0.709354] vdd_gpu: 500 <--> 1350 mV at 900 mV, enabled
- [ 0.710686] rk808 0-0020: Looking up vcc2-supply from device tree
- [ 0.711264] vdd_gpu: supplied by vcc3v3_sys
- [ 0.712805] vcc_ddr: will resolve supply early: vcc3
- [ 0.713263] rk808 0-0020: Looking up vcc3-supply from device tree
- [ 0.713879] vcc_ddr: supplied by vcc3v3_sys
- [ 0.714267] vcc3v3_sys: could not add device link regulator.8: -ENOENT
- [ 0.717721] vcc_ddr: at 500 mV, enabled
- [ 0.721920] vdd_npu: 500 <--> 1350 mV at 900 mV, disabled
- [ 0.723170] rk808 0-0020: Looking up vcc4-supply from device tree
- [ 0.723737] vdd_npu: supplied by vcc3v3_sys
- [ 0.725700] vcc_1v8: will resolve supply early: vcc9
- [ 0.726156] rk808 0-0020: Looking up vcc9-supply from device tree
- [ 0.726714] vcc_1v8: supplied by vcc3v3_sys
- [ 0.727097] vcc3v3_sys: could not add device link regulator.10: -ENOENT
- [ 0.730077] vcc_1v8: 1800 mV, enabled
- [ 0.732788] vdda0v9_image: 900 mV, disabled
- [ 0.733912] rk808 0-0020: Looking up vcc5-supply from device tree
- [ 0.734479] vdda0v9_image: supplied by vcc3v3_sys
- [ 0.736434] vdda_0v9: will resolve supply early: vcc5
- [ 0.736899] rk808 0-0020: Looking up vcc5-supply from device tree
- [ 0.737491] vdda_0v9: supplied by vcc3v3_sys
- [ 0.737885] vcc3v3_sys: could not add device link regulator.12: -ENOENT
- [ 0.741395] vdda_0v9: 900 mV, enabled
- [ 0.744160] vdda0v9_pmu: will resolve supply early: vcc5
- [ 0.744647] rk808 0-0020: Looking up vcc5-supply from device tree
- [ 0.745209] vdda0v9_pmu: supplied by vcc3v3_sys
- [ 0.745659] vcc3v3_sys: could not add device link regulator.13: -ENOENT
- [ 0.749636] vdda0v9_pmu: 900 mV, enabled
- [ 0.752343] vccio_acodec: 3300 mV, disabled
- [ 0.753512] rk808 0-0020: Looking up vcc6-supply from device tree
- [ 0.754081] vccio_acodec: supplied by vcc3v3_sys
- [ 0.757000] vccio_sd: 1800 <--> 3300 mV at 3300 mV, enabled
- [ 0.758300] rk808 0-0020: Looking up vcc6-supply from device tree
- [ 0.758867] vccio_sd: supplied by vcc3v3_sys
- [ 0.760943] vcc3v3_pmu: will resolve supply early: vcc6
- [ 0.761472] rk808 0-0020: Looking up vcc6-supply from device tree
- [ 0.762036] vcc3v3_pmu: supplied by vcc3v3_sys
- [ 0.762441] vcc3v3_sys: could not add device link regulator.16: -ENOENT
- [ 0.766442] vcc3v3_pmu: 3300 mV, enabled
- [ 0.769052] vcca_1v8: will resolve supply early: vcc7
- [ 0.769550] rk808 0-0020: Looking up vcc7-supply from device tree
- [ 0.770114] vcca_1v8: supplied by vcc3v3_sys
- [ 0.770505] vcc3v3_sys: could not add device link regulator.17: -ENOENT
- [ 0.774025] vcca_1v8: 1800 mV, enabled
- [ 0.776754] vcca1v8_pmu: will resolve supply early: vcc7
- [ 0.777242] rk808 0-0020: Looking up vcc7-supply from device tree
- [ 0.777839] vcca1v8_pmu: supplied by vcc3v3_sys
- [ 0.778259] vcc3v3_sys: could not add device link regulator.18: -ENOENT
- [ 0.782273] vcca1v8_pmu: 1800 mV, enabled
- [ 0.785029] vcca1v8_image: 1800 mV, disabled
- [ 0.786313] rk808 0-0020: Looking up vcc7-supply from device tree
- [ 0.786897] vcca1v8_image: supplied by vcc3v3_sys
- [ 0.788467] vcc_3v3: will resolve supply early: vcc9
- [ 0.788941] rk808 0-0020: Looking up vcc9-supply from device tree
- [ 0.789552] vcc_3v3: supplied by vcc3v3_sys
- [ 0.789947] vcc3v3_sys: could not add device link regulator.20: -ENOENT
- [ 0.792524] vcc_3v3: at 3300 mV, enabled
- [ 0.794752] vcc3v3_sd: no parameters, enabled
- [ 0.795464] rk808 0-0020: Looking up vcc8-supply from device tree
- [ 0.796036] vcc3v3_sd: supplied by vcc3v3_sys
- [ 0.803170] input: rk805 pwrkey as /devices/platform/fdd40000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input0
- [ 0.816956] rk808-rtc rk808-rtc: registered as rtc0
- [ 0.820201] rk808-rtc rk808-rtc: setting system clock to 2017-08-05T09:00:09 UTC (1501923609)
- [ 0.822757] arm-scmi firmware:scmi: Failed. SCMI protocol 21 not active.
- [ 0.828725] arm-scmi firmware:scmi: Failed. SCMI protocol 19 not active.
- [ 0.830220] sdhci: Secure Digital Host Controller Interface driver
- [ 0.830773] sdhci: Copyright(c) Pierre Ossman
- [ 0.831335] Synopsys Designware Multimedia Card Interface Driver
- [ 0.832115] sdhci-pltfm: SDHCI platform and OF driver helper
- [ 0.832615] dwmmc_rockchip fe2b0000.mmc: IDMAC supports 32-bit address mode.
- [ 0.833263] dwmmc_rockchip fe2b0000.mmc: Using internal DMA controller.
- [ 0.833886] dwmmc_rockchip fe2b0000.mmc: Version ID is 270a
- [ 0.834433] dwmmc_rockchip fe2b0000.mmc: DW MMC controller at irq 23,32 bit host data width,256 deep fifo
- [ 0.835365] dwmmc_rockchip fe2b0000.mmc: Looking up vmmc-supply from device tree
- [ 0.836148] dwmmc_rockchip fe2b0000.mmc: Looking up vqmmc-supply from device tree
- [ 0.836980] dwmmc_rockchip fe2b0000.mmc: Got CD GPIO
- [ 0.837720] ledtrig-cpu: registered to indicate activity on CPUs
- [ 0.838673] sdhci-dwcmshc fe310000.mmc: Looking up vmmc-supply from device tree
- [ 0.838933] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
- [ 0.839328] sdhci-dwcmshc fe310000.mmc: Looking up vmmc-supply property in node /mmc@fe310000 failed
- [ 0.839975] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
- [ 0.840735] sdhci-dwcmshc fe310000.mmc: Looking up vqmmc-supply from device tree
- [ 0.841596] usbcore: registered new interface driver usbhid
- [ 0.841957] sdhci-dwcmshc fe310000.mmc: Looking up vqmmc-supply property in node /mmc@fe310000 failed
- [ 0.842427] usbhid: USB HID core driver
- [ 0.843792] ashmem: initialized
- [ 0.849747] NET: Registered PF_PACKET protocol family
- [ 0.850483] Bluetooth: RFCOMM TTY layer initialized
- [ 0.850947] Bluetooth: RFCOMM socket layer initialized
- [ 0.851432] Bluetooth: RFCOMM ver 1.11
- [ 0.851780] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
- [ 0.852249] Bluetooth: BNEP filters: protocol multicast
- [ 0.852741] Bluetooth: BNEP socket layer initialized
- [ 0.853185] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
- [ 0.853785] Bluetooth: HIDP socket layer initialized
- [ 0.854408] 9pnet: Installing 9P2000 support
- [ 0.854875] Key type dns_resolver registered
- [ 0.855783] registered taskstats version 1
- [ 0.856166] Loading compiled-in X.509 certificates
- [ 0.857565] mmc_host mmc0: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
- [ 0.861544] zswap: loaded using pool zstd/zsmalloc
- [ 0.873383] mmc1: SDHCI controller on fe310000.mmc [fe310000.mmc] using ADMA
- [ 0.901472] rockchip-iodomain fdc20000.syscon:io-domains: Looking up pmuio1-supply from device tree
- [ 0.903443] rockchip-iodomain fdc20000.syscon:io-domains: Looking up pmuio2-supply from device tree
- [ 0.905265] rockchip-iodomain fdc20000.syscon:io-domains: Looking up vccio1-supply from device tree
- [ 0.907011] rockchip-iodomain fdc20000.syscon:io-domains: Looking up vccio2-supply from device tree
- [ 0.907934] rockchip-iodomain fdc20000.syscon:io-domains: Looking up vccio2-supply property in node /syscon@fdc20000/io-domains fd
- [ 0.909159] rockchip-iodomain fdc20000.syscon:io-domains: Looking up vccio3-supply from device tree
- [ 0.911229] rockchip-iodomain fdc20000.syscon:io-domains: Looking up vccio4-supply from device tree
- [ 0.913346] rockchip-iodomain fdc20000.syscon:io-domains: Looking up vccio5-supply from device tree
- [ 0.914973] rockchip-iodomain fdc20000.syscon:io-domains: Looking up vccio6-supply from device tree
- [ 0.916199] Freeing initrd memory: 19988K
- [ 0.916334] rockchip-iodomain fdc20000.syscon:io-domains: Looking up vccio7-supply from device tree
- [ 0.918998] cfg80211: Loading compiled-in X.509 certificates for regulatory database
- [ 0.925590] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
- [ 0.926293] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
- [ 0.927051] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db
- [ 0.928750] vccio_sd: ramp_delay not set
- [ 0.955582] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 100000000Hz, actual 50000000HZ div = 0)
- [ 0.957396] mmc1: new HS200 MMC card at address 0001
- [ 0.958449] mmcblk1: mmc1:0001 SPeMMC 14.5 GiB
- [ 0.961428] mmcblk1boot0: mmc1:0001 SPeMMC 4.00 MiB
- [ 0.963406] mmcblk1boot1: mmc1:0001 SPeMMC 4.00 MiB
- [ 0.965878] mmcblk1rpmb: mmc1:0001 SPeMMC 4.00 MiB, chardev (238:0)
- [ 0.979537] dwmmc_rockchip fe2b0000.mmc: Successfully tuned phase to 352
- [ 0.980142] mmc0: new ultra high speed SDR50 SDXC card at address aaaa
- [ 0.981485] mmcblk0: mmc0:aaaa SL64G 59.5 GiB
- [ 0.990738] mmcblk0: p1 p2 p3
- [ 1.068600] ALSA device list:
- [ 1.068883] No soundcards found.
- [ 1.069464] dw-apb-uart fe660000.serial: forbid DMA for kernel console
- [ 1.074874] Freeing unused kernel memory: 6016K
- [ 1.081398] Run /init as init process
- [ 1.081726] with arguments:
- [ 1.081987] /init
- [ 1.082189] with environment:
- [ 1.082467] HOME=/
- [ 1.082677] TERM=linux
- Starting syslogd: OK
- Starting klogd: OK
- Running sysctl: OK
- Saving random seed: [ 1.158352] random: dd: uninitialized urandom read (512 bytes read)
- OK
- Starting network: OK
- Starting dhcpcd...
- dhcpcd-9.4.0 starting
- [ 1.196425] random: dhcpcd: uninitialized urandom read (112 bytes read)
- forked to background, child pid 195
- [ 1.252753] rk_gmac-dwmac fe010000.ethernet eth0: no phy at addr -1
- no interfaces have a carrier
- [ 1.253467] rk_gmac-dwmac fe010000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
- [ 1.254850] rk_gmac-dwmac fe2a0000.ethernet eth1: no phy at addr -1
- [ 1.255427] rk_gmac-dwmac fe2a0000.ethernet eth1: stmmac_open: Cannot attach to PHY (error: -19)
- [ 5.761358] random: crng init done
- ssh-keygen: generating new host keys: RSA DSA ECDSA ED25519
- Starting sshd: OK
- Welcome to Buildroot
- buildroot login: [ 31.713552] vcc3v3_lcd0_n: disabling
- [ 31.713935] vcc3v3_lcd1_n: disabling
- [ 31.714851] vdd_gpu: disabling
- [ 62.433715] cfg80211: failed to load regulatory.db
- Welcome to Buildroot
- buildroot login: root
- #
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement