Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- ; Configuration file for Duet WiFi (firmware version 3.3)
- ; executed by the firmware on start-up
- ;
- ; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Jun 06 2022 08:44:23 GMT+0200 (centraleuropeisk sommartid)
- ; General preferences
- M575 P1 S1 B57600 ; enable support for PanelDue
- G90 ; send absolute coordinates...
- M83 ; ...but relative extruder moves
- M550 P"Prusa Bear" ; set printer name
- ; Network
- M552 S1 ; enable network
- M586 P0 S1 ; enable HTTP
- M586 P1 S0 ; disable FTP
- M586 P2 S0 ; disable Telnet
- ; Drives
- M569 P0 S0 ; physical drive 0 goes forwards X-motor
- M569 P1 S0 ; physical drive 1 goes forwards Y-motor
- M569 P2 S0 ; physical drive 2 goes forwards Z-motor
- M569 P3 S1 ; physical drive 3 goes forwards Extruder-motor
- M569 P4 S0 ; physical drive 4 goes forwards Z-motor
- M584 X0 Y1 Z2:4 E3 ; set drive mapping
- M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
- M92 X100.00 Y100.00 Z397.00 E146.100 ; set steps per mm
- M566 X900.00 Y900.00 Z160.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
- M203 X9000.00 Y9000.00 Z400.00 E1200.00 ; set maximum speeds (mm/min)
- M201 X500.00 Y500.00 Z180.00 E250.00 ; set accelerations (mm/s^2)
- M906 X700 Y700 Z700 E700 I30 ; set motor currents (mA) and motor idle factor in per cent
- M84 S5 ; Set idle timeout
- ; Axis Limits
- M208 X0 Y0 Z0 S1 ; set axis minima
- M208 X250 Y210 Z210 S0 ; set axis maxima
- M564 H0 ; Allow unhomed movement "NY"
- ; Endstops
- M574 X1 S1 P"xstop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
- M574 Y1 S1 P"ystop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
- M574 Z1 S2 ; configure Z-probe endstop for low end on Z
- M556 S100 X0,053 ; Kalibrering Califlower
- ; Z-Probe
- M558 P1 C"zprobe.in" H3 F800 T10000 ; set Z probe type to unmodulated and the dive height + speeds (FXXX är hastigheten)
- G31 P1000 X11 Y2 Z0.260 ; set Z probe trigger value, offset and trigger height
- M557 X15:230 Y15:195 S35 ; define mesh grid (SXX ändrar distansen mellan probepunkterna)
- ; Bed Heater
- M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp PIDTUNE= m303 H0 S(TEMP)
- M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
- M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
- M140 H0 ; map heated bed to heater 0
- M143 H0 S110 ; set temperature limit for heater 0 to 110C
- ; Nozzle Heater
- M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp PIDTUNE= m303 H1 S(TEMP)
- M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
- M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
- M143 H1 S310 ; set temperature limit for heater 1 to 300C
- ; Fans
- M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
- M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
- M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
- M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
- ; Tools
- M563 P0 D0 H1 F0 ; define tool 0
- G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
- G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
- ;Filamentsensor
- ;M591 D0 P1 C"e0stop" S1 ; simple sensor (low signal when filament present) connected to E0 endstop for drive 0, enabled
- M584 X0 Y1 Z2:4 E3; two Z motors connected to driver 2 (left motor) and driver 4 (right motor)
- M671 X-20:250 Y0:0 S1:5 ; position of leadscrew/bed pivot point at left and right of X axis
- M208 X-5:250 Y0:210 ; X carriage moves from -5 to 205, Y bed goes from 0 to 200
- M501 ; Custom settings are not defined
- T0 ; select first tool
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
