API tools faq
paste
Advertisement
Guest User

QCA8334...

a guest
Jun 15th, 2019
359
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
Python 19.95 KB | None | 0 0
raw download clone embed print report
  1.  
  2. U-Boot 1.1.4 (Jun 22 2014 - 15:02:11)
  3.  
  4. ap135 - Scorpion 1.0DRAM:
  5. sri
  6. Scorpion 1.0
  7. ath_ddr_initial_config(200): (32bit) ddr2 init
  8. tap = 0x00000003
  9. Tap (low, high) = (0x4, 0x1d)
  10. Tap values = (0x10, 0x10, 0x10, 0x10)
  11. 128 MB
  12. Top of RAM usable for U-Boot at: 88000000
  13. Reserving 208k for U-Boot at: 87fc8000
  14. Reserving 192k for malloc() at: 87f98000
  15. Reserving 44 Bytes for Board Info at: 87f97fd4
  16. Reserving 36 Bytes for Global Data at: 87f97fb0
  17. Reserving 128k for boot params() at: 87f77fb0
  18. Stack Pointer at: 87f77f98
  19. Now running in RAM - U-Boot at: 87fc8000
  20. Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
  21. flash size 16MB, sector count = 256
  22. Flash: 32 MB
  23. *** Warning *** : PCIe WLAN Module not found !!!
  24. In:    serial
  25. Out:   serial
  26. Err:   serial
  27. Net:   ath_gmac_enet_initialize...
  28. athrs_sgmii_res_cal: cal value = 0x1
  29. Fetching MAC Address from 0x87feaa8c
  30. Fetching MAC Address from 0x87feaa8c
  31. ath_gmac_enet_initialize: reset mask:c02200
  32. Scorpion  ----> S17 PHY *
  33. Vlan config...
  34. s17 phy0 register value 0x00004140
  35. TEST: FINAL REG VAL after TX Calibration - 0x86000000
  36. TEST: FINAL XMII VAL after RX Calibration - 0x96000000
  37. TEST: FINAL ETH_CFG VAL after RX Calibration - 0x00000001
  38. athrs17_reg_init: complete
  39. : cfg1 0x80000000 cfg2 0x7335
  40. eth0: 88:b1:e1:be:d3:1f
  41. eth0 up
  42. athrs17_reg_init_wan done
  43. SGMII in forced mode
  44. athr_gmac_sgmii_setup SGMII done
  45. : cfg1 0x800c0000 cfg2 0x7214
  46. eth1: 88:b1:e1:be:d3:1e
  47. eth1 up
  48. eth0, eth1
  49. Setting 0x18116290 to 0x50a1a14f
  50. Hit enter key to stop autoboot:  0
  51. multiboot=1
  52. Trying eth0
  53. dup 1 speed 1000
  54. Using eth0 device
  55. TFTP from server 192.168.1.100; our IP address is 192.168.1.1
  56. Filename 'openwrt-ath79-generic-airtight_c-75-initramfs-kernel.bin'.
  57. Load address: 0x81000000
  58. Loading: #################################################################
  59.          #################################################################
  60.          #################################################################
  61.          #################################################################
  62.          #################################################################
  63.          #################################################################
  64.          #################################################################
  65.          #################################################################
  66.          #################################################################
  67.          #################################################################
  68.          #################################################################
  69.          #################################################################
  70.          ####################################
  71. done
  72. Bytes transferred = 4177552 (3fbe90 hex)
  73.  
  74. ## Checking Image at 81000000 ...
  75.    Image Name:   MIPS OpenWrt Linux-4.14.125
  76.    Created:      2019-06-15  18:34:34 UTC
  77.    Image Type:   MIPS Linux Kernel Image (lzma compressed)
  78.    Data Size:    4177488 Bytes =  4 MB
  79.    Load Address: 80060000
  80.    Entry Point:  80060000
  81.    Verifying Checksum ... OK
  82. Attempting to boot OpenWRT Ram Image...
  83. ## Booting image at 81000000 ...
  84.    Image Name:   MIPS OpenWrt Linux-4.14.125
  85.    Created:      2019-06-15  18:34:34 UTC
  86.    Image Type:   MIPS Linux Kernel Image (lzma compressed)
  87.    Data Size:    4177488 Bytes =  4 MB
  88.    Load Address: 80060000
  89.    Entry Point:  80060000
  90.    Verifying Checksum at 0x81000040 ...OK
  91.    Uncompressing Kernel Image ... OK
  92. No initrd
  93. ## Transferring control to Linux (at address 80060000) ...
  94. ## Giving linux memsize in bytes, 134217728
  95.  
  96. Starting kernel ...
  97.  
  98. [    0.000000] Linux version 4.14.125 (osboxes@openwrt-dev) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10209-0301f5e9ec)) #0 Fri Jun 14 01:15:27 2019
  99. [    0.000000] bootconsole [early0] enabled
  100. [    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
  101. [    0.000000] MIPS: machine is AirTight C-75
  102. [    0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
  103. [    0.000000] Determined physical RAM map:
  104. [    0.000000]  memory: 08000000 @ 00000000 (usable)
  105. [    0.000000] Initrd not found or empty - disabling initrd
  106. [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  107. [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  108. [    0.000000] Zone ranges:
  109. [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
  110. [    0.000000] Movable zone start for each node
  111. [    0.000000] Early memory node ranges
  112. [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
  113. [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
  114. [    0.000000] random: get_random_bytes called from start_kernel+0x98/0x4a0 with crng_init=0
  115. [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
  116. [    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
  117. [    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
  118. [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  119. [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  120. [    0.000000] Writing ErrCtl register=00000000
  121. [    0.000000] Readback ErrCtl register=00000000
  122. [    0.000000] Memory: 115308K/131072K available (4006K kernel code, 161K rwdata, 944K rodata, 8704K init, 210K bss, 15764K reserved, 0K cma-reserved)
  123. [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  124. [    0.000000] NR_IRQS: 51
  125. [    0.000000] CPU clock: 720.000 MHz
  126. [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
  127. [    0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
  128. [    0.008292] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
  129. [    0.074984] pid_max: default: 32768 minimum: 301
  130. [    0.080108] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  131. [    0.087145] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  132. [    0.098381] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  133. [    0.108879] futex hash table entries: 256 (order: -1, 3072 bytes)
  134. [    0.115468] pinctrl core: initialized pinctrl subsystem
  135. [    0.121799] NET: Registered protocol family 16
  136. [    0.132217] PCI host bridge /ahb/apb/pcie-controller@180c0000 ranges:
  137. [    0.139082]  MEM 0x0000000010000000..0x0000000011ffffff
  138. [    0.144669]   IO 0x0000000000000000..0x0000000000000000
  139. [    0.150560] PCI host bridge /ahb/apb/pcie-controller@18250000 ranges:
  140. [    0.157450]  MEM 0x0000000012000000..0x0000000013ffffff
  141. [    0.163004]   IO 0x0000000000000001..0x0000000000000001
  142. [    0.168566] ar724x-pci 18250000.pcie-controller: PCIe link is down
  143. [    0.190088] PCI host bridge to bus 0000:00
  144. [    0.194451] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
  145. [    0.201798] pci_bus 0000:00: root bus resource [io  0x0000]
  146. [    0.207725] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
  147. [    0.214949] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
  148. [    0.223775] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
  149. [    0.231594] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
  150. [    0.239405] PCI host bridge to bus 0000:01
  151. [    0.243789] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
  152. [    0.251094] pci_bus 0000:01: root bus resource [io  0x0001]
  153. [    0.257025] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
  154. [    0.264240] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
  155. [    0.275069] clocksource: Switched to clocksource MIPS
  156. [    0.281350] NET: Registered protocol family 2
  157. [    0.286648] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  158. [    0.294067] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  159. [    0.300873] TCP: Hash tables configured (established 1024 bind 1024)
  160. [    0.307748] UDP hash table entries: 256 (order: 0, 4096 bytes)
  161. [    0.313972] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  162. [    0.320932] NET: Registered protocol family 1
  163. [    0.485151] Crashlog allocated RAM at address 0x3f00000
  164. [    0.491956] workingset: timestamp_bits=14 max_order=15 bucket_order=1
  165. [    0.503733] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  166. [    0.509977] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  167. [    0.580868] io scheduler noop registered
  168. [    0.585041] io scheduler deadline registered (default)
  169. [    0.592309] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68
  170. [    0.600601] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  171. [    0.607988] console [ttyS0] disabled
  172. [    0.611820] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 8, base_baud = 2500000) is a 16550A
  173. [    0.621031] console [ttyS0] enabled
  174. [    0.621031] console [ttyS0] enabled
  175. [    0.628446] bootconsole [early0] disabled
  176. [    0.628446] bootconsole [early0] disabled
  177. [    0.642422] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
  178. [    0.647626] 4 fixed-partitions partitions found on MTD device spi0.0
  179. [    0.654062] Creating 4 MTD partitions on "spi0.0":
  180. [    0.658942] 0x000000000000-0x000000040000 : "u-boot"
  181. [    0.664635] 0x000000040000-0x000000060000 : "uboot-env"
  182. [    0.670585] 0x000000060000-0x000000ff0000 : "firmware"
  183. [    0.679251] 2 uimage-fw partitions found on MTD device firmware
  184. [    0.685299] Creating 2 MTD partitions on "firmware":
  185. [    0.690335] 0x000000000000-0x000000200000 : "kernel"
  186. [    0.696017] 0x000000200000-0x000000f90000 : "rootfs"
  187. [    0.701619] mtd: device 4 (rootfs) set to be root filesystem
  188. [    0.707438] mtdsplit: no squashfs found in "rootfs"
  189. [    0.712405] 0x000000ff0000-0x000001000000 : "art"
  190. [    0.718728] libphy: Fixed MDIO Bus: probed
  191. [    1.056773] libphy: ag71xx_mdio: probed
  192. [    1.080129] switch0: Atheros AR8337 rev. 2 switch registered on mdio-bus.0
  193. [    1.087140] ar8327: qca,phy-rgmii-en is not specified
  194. [    1.092446] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:04 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
  195. [    1.103826] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
  196. [    1.111510] NET: Registered protocol family 10
  197. [    1.119648] Segment Routing with IPv6
  198. [    1.123449] NET: Registered protocol family 17
  199. [    1.128052] 8021q: 802.1Q VLAN Support v1.8
  200. [    1.165034] Freeing unused kernel memory: 8704K
  201. [    1.169657] This architecture does not have kernel memory protection.
  202. [    1.188355] init: Console is alive
  203. [    1.191989] init: - watchdog -
  204. [    1.212154] kmodloader: loading kernel modules from /etc/modules-boot.d/*
  205. [    1.220921] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
  206. [    1.229469] init: - preinit -
  207. [    1.391744] random: jshn: uninitialized urandom read (4 bytes read)
  208. [    1.471946] random: jshn: uninitialized urandom read (4 bytes read)
  209. [    1.554454] random: jshn: uninitialized urandom read (4 bytes read)
  210. [    1.733239] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  211. Press the [f] key and hit [enter] to enter failsafe mode
  212. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  213. [    3.635067] random: fast init done
  214. [    4.863868] procd: - early -
  215. [    4.867459] procd: - watchdog -
  216. [    5.412895] procd: - watchdog -
  217. [    5.416352] procd: - ubus -
  218. [    5.424812] urandom_read: 4 callbacks suppressed
  219. [    5.424818] random: ubusd: uninitialized urandom read (4 bytes read)
  220. [    5.469515] random: ubusd: uninitialized urandom read (4 bytes read)
  221. [    5.476385] random: ubusd: uninitialized urandom read (4 bytes read)
  222. [    5.483630] procd: - init -
  223. Please press Enter to activate this console.
  224. [    5.895682] kmodloader: loading kernel modules from /etc/modules.d/*
  225. [    5.908033] urngd: v1.0.0 started.
  226. [    5.918981] ip6_tables: (C) 2000-2006 Netfilter Core Team
  227. [    5.937473] Loading modules backported from Linux version v4.19.32-0-g3a2156c839c7
  228. [    5.945190] Backport generated by backports.git v4.19.32-1-0-g1c4f7569
  229. [    5.967083] ip_tables: (C) 2000-2006 Netfilter Core Team
  230. [    5.991617] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
  231. [    6.087690] xt_time: kernel timezone is -0000
  232. [    6.179622] PPP generic driver version 2.4.2
  233. [    6.189011] random: crng init done
  234. [    6.193615] NET: Registered protocol family 24
  235. [    6.221029] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
  236. [    6.226958] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
  237. [    6.508320] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
  238. [    6.519193] ath10k_pci 0000:00:00.0: Falling back to user helper
  239. [    6.615148] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed
  240. [    6.624451] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/cal-pci-0000:00:00.0.bin failed with error -2
  241. [    6.634983] ath10k_pci 0000:00:00.0: Falling back to user helper
  242. [    6.908496] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
  243. [    6.919386] ath10k_pci 0000:00:00.0: Falling back to user helper
  244. [    7.060211] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
  245. [    7.071537] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 168c:3223
  246. [    7.080933] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
  247. [    7.093971] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-1.0-00043 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 ed0aafd8
  248. [    7.195232] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
  249. [    7.205839] ath10k_pci 0000:00:00.0: Falling back to user helper
  250. [    7.327305] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
  251. [    7.336514] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
  252. [    8.453654] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
  253. [    8.677066] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=13
  254. [    8.725429] kmodloader: done loading kernel modules from /etc/modules.d/*
  255. [   37.737367] br-lan: port 1(eth0) entered blocking state
  256. [   37.742676] br-lan: port 1(eth0) entered disabled state
  257. [   37.748258] device eth0 entered promiscuous mode
  258. [   37.795272] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  259.  
  260.  
  261.  
  262. BusyBox v1.30.1 () built-in shell (ash)
  263.  
  264.   _______                     ________        __
  265.  |       |.-----.-----.-----.|  |  |  |.----.|  |_
  266.  |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
  267.  |_______||   __|_____|__|__||________||__|  |____|
  268.           |__| W I R E L E S S   F R E E D O M
  269.  -----------------------------------------------------
  270.  OpenWrt SNAPSHOT, r10216-76098b6748
  271.  -----------------------------------------------------
  272. === WARNING! =====================================
  273. There is no root password defined on this device!
  274. Use the "passwd" command to set up a new password
  275. in order to prevent unauthorized SSH logins.
  276. --------------------------------------------------
  277. root@OpenWrt:/# uci set wireless.radio0.disabled=0
  278. ommit
  279. /etc/init.d/network reload
  280. /etc/init.d/network restartroot@OpenWrt:/# uci commit
  281. root@OpenWrt:/# /etc/init.d/network reload
  282. 'radio1' is disabled
  283. 'radio1' is disabled
  284. root@OpenWrt:/# /etc/init.d/network restart[  386.083279] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
  285. [  386.105092] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
  286. [  386.114591] br-lan: port 2(wlan0) entered blocking state
  287. [  386.120038] br-lan: port 2(wlan0) entered disabled state
  288. [  386.125714] device wlan0 entered promiscuous mode
  289. [  386.444246] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
  290. [  386.450887] br-lan: port 2(wlan0) entered blocking state
  291. [  386.456310] br-lan: port 2(wlan0) entered forwarding state
  292. [  386.480786] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  293.  
  294. 'radio1' is disabled
  295. [  390.511748] br-lan: port 2(wlan0) entered disabled state
  296. [  390.547026] device eth0 left promiscuous mode
  297. [  390.551528] br-lan: port 1(eth0) entered disabled state
  298. [  390.591093] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  299. [  390.611945] device wlan0 left promiscuous mode
  300. [  390.616577] br-lan: port 2(wlan0) entered disabled state
  301. root@OpenWrt:/# [  394.496909] br-lan: port 1(eth0) entered blocking state
  302. [  394.502213] br-lan: port 1(eth0) entered disabled state
  303. [  394.507791] device eth0 entered promiscuous mode
  304. [  394.538161] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  305. [  397.960553] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
  306. [  397.991888] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
  307. [  398.008285] br-lan: port 2(wlan0) entered blocking state
  308. [  398.013677] br-lan: port 2(wlan0) entered disabled state
  309. [  398.019367] device wlan0 entered promiscuous mode
  310. [  398.358822] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
  311. [  398.365454] br-lan: port 2(wlan0) entered blocking state
  312. [  398.370864] br-lan: port 2(wlan0) entered forwarding state
  313. [  398.422289] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  314.  
  315. root@OpenWrt:/# swconfig list
  316. Found: switch0 - mdio-bus.0
  317. root@OpenWrt:/# swconfig dev switch0 show
  318. Global attributes:
  319.         enable_vlan: 0
  320.         ar8xxx_mib_poll_interval: [  884.696388] CPU 0 Unable to handle kernel paging request at virtual address 00000010, epc == 802e4088, ra == 802df654
  321. 0
  322.         ar8xxx_mib_t[  884.708524] Oops[#1]:
  323. [  884.712208] CPU: 0 PID: 2698 Comm: swconfig Not tainted 4.14.125 #0
  324. [  884.718558] task: 87d49780 task.stack: 87c40000
  325. [  884.723147] $ 0   : 00000000 00000001 00000000 00000006
  326. [  884.728453] $ 4   : 00000001 8046a864 87c41bc8 87dae040
  327. [  884.733759] $ 8   : 86c5c980 80444058 00000001 fffffffe
  328. [  884.739066] $12   : 805591ec 00000040 00000000 00080002
  329. [  884.744372] $16   : 87c41c48 87dae000 8046a864 87dae048
  330. [  884.749678] $20   : 00000007 00000004 80557b20 87c41cac
  331. [  884.754985] $24   : 00000000 77f57820
  332. [  884.760292] $28   : 87c40000 87c41bb0 86c5c980 802df654
  333. [  884.765599] Hi    : 00000000
  334. [  884.768521] Lo    : 00000068
  335. [  884.771460] epc   : 802e4088 ar8327_sw_get_eee+0x28/0x44
  336. [  884.776849] ra    : 802df654 swconfig_get_attr+0xe4/0x59c
  337. [  884.782319] Status: 1100dc03 KERNEL EXL IE
  338. [  884.786561] Cause : 00800008 (ExcCode 02)
  339. [  884.790626] BadVA : 00000010
  340. [  884.793539] PrId  : 00019750 (MIPS 74Kc)
  341. [  884.797515] Modules linked in: ath9k ath9k_common pppoe ppp_async ath9k_hw ath10k_pci ath10k_core ath pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_FLOWOFFLOAD slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filter ip_tables crc_ccitt compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 gpio_button_hotplug
  342. [  884.861233] Process swconfig (pid: 2698, threadinfo=87c40000, task=87d49780, tls=77ff8eb8)
  343. [  884.869605] Stack : 87dae000 87c41c48 80553b08 802df184 87c41bcc 00000007 8046a864 00000001
  344. [  884.878088]         00000000 00000000 000003e8 869766c0 87c41c2f 86e7c224 00000008 00000015
  345. [  884.886571]         ffff3fff 80247694 869766c0 738d117b 80abfc00 80abfc00 87d7b000 805539f8
  346. [  884.895054]         80553ab8 805539f8 80553ab8 86e7c200 869766c0 00000000 00000004 8035de58
  347. [  884.903537]         00000000 00000000 86976240 869766c0 80469858 87c41cac 5d05ae84 00000a8a
  348. [  884.912020]         ...
  349. [  884.914503] Call Trace:
  350. [  884.916982] [<802e4088>] ar8327_sw_get_eee+0x28/0x44
  351. [  884.922015] Code: 10430007  00822021  00001025 <9083000f> 03e00008  acc3000c  03e00008  2402ffea  03e00008
  352. [  884.931918]
  353. ype: 0
  354.         enable_[  884.933618] ---[ end trace a1f84287571b0c94 ]---
  355. mirror_rx: 0
  356.         enable_mirror_tx:[  884.941158] Kernel panic - not syncing: Fatal exception
  357. [  884.948577] Rebooting in 3 seconds..
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!