v0.43a
Drive: 2(USB)
Model: SandForce
Fw   : 506ABBM0
Size : 244140 MB
--- SandForce specific ---
Signature   : 0-0-
HW Revision : 400026BB (B02)
FW          : [506ABBM0        ]
FW string   : [B:FW_PPRO_MP3_5_0_2_20120315:FW_PPRO_5_0_6_Release-538524                       ]
Config file : [cfg/cfg_MLC_Toshiba_64Gb_TH58NVG7DDJTA20_2Q_4C_1D_S                             ]
ROM Revision: [300             ]
NAND ID     : 0x2c, 0x88, 0x5, 0xca, 0xa9, 0x0, 0x0, 0x0
Page Size   : 17664
NAND CE     : 4
Sector/Page : 8
Die/CE      : 1
Block/Die   : 1024
Page/Block  : 256
Raw Size    : 536870912
NAND Max EC : 4294967295

Max PE Cycles             : need fw.360+/520+
Cur PE Cycles             : need fw.360+/520+
Life In Seconds           : 0 (Not Set)
LBA Size                  : 0
Sector Size               : 0
Sector Align              : +0
NAND ID                   : 0x00,0x00
Serial Output Control     : Default(Off)
Erase R Block             : Disable
Panic Handling Enabled    : Disable
Panic On SATA Error       : Disable
Write Throttling Test Mode: Disable
R.A.I.S.E.                : Enable

Flash CE    : 32
Bank00: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die
Bank01: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die
Bank02: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die
Bank03: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die
Bank08: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die
Bank09: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die
Bank10: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die
Bank11: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die
Bank16: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die
Bank17: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die
Bank18: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die
Bank19: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die
Bank24: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die
Bank25: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die
Bank26: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die
Bank27: 0x2c,0x88,0x5,0xca,0xa9,0x0,0x0,0x0 - Micron MLC 64Gb/CE 32Gb/die

Driver Fail, possible ide mode!
UART freq                                            : 0
SATA Status Coalesting                               : 0
Compressible data performance tuning option          : 0 (no tuning for compr. data)
Serial Output Control                                : 0 (Default)
Write Speed Limit                                    : 0 (Off)

Led Settings
Activity LED Polarity                                : 0 (Normal)
Fault LED Polarity                                   : 0 (Normal)
LED Blink Rate                                       : 0 (250ms)

Power Managment Settings
Power Management Version                             : 0 (SF1)
Sleep command mode                                   : 0 (Default)
IDLE command mode                                    : 0 (Default)

Temperature Sensor Settings
Sensor 1:
Device ID                                            : 0 (Default)
Device Address                                       : 0
Max Temperature Threshold Level 1 Entry Point (MT1)  : 0n (Default - 65C)
Max Temperature Threshold Level 2 Entry Point (MT2)  : 0n (Default - 70C)
Min Temperature Threshold (LT1)                      : 0n (Default - 0C)
Max Temperature Threshold Behavior for MT1 (MT1B)    : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B)    : 0 (Default)
Min Temperature Threshold Behavior (LT1B)            : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0 (Default - MT1)

Sensor 2:
Device ID                                            : 0 (Default)
Device Address                                       : 0
Max Temperature Threshold Level 1 Entry Point (MT1)  : 0
Max Temperature Threshold Level 2 Entry Point (MT2)  : 0
Min Temperature Threshold (LT1)                      : 0
Max Temperature Threshold Behavior for MT1 (MT1B)    : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B)    : 0 (Default)
Min Temperature Threshold Behavior (LT1B)            : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0

Security Erase Options
Security Erase Behavior                              : 0 (Default)
Enhanced Security Erase Behavior (Military Erase)    : 0 (Default)

SATA Command and Firmware Options
Flush Cache Behavior                                 : 0 (Default)
ATA Security Set Enable                              : 0 (Default)
Spread Spectrum Clocking Enable                      : 0 (Default)
SATA Link Handling on Reboot                         : 0 (Default)
ACS2 Support                                         : 0 (Default)
Failed Secure Unlock Delay Enable                    : 0 (Default(No delay))
Seek Complete in Error Status                        : 0 (Default)
Read Long with Retry and without Retry               : 0 (Default)
Read Sectors without Retry                           : 0 (Default)
Write DMA without Retry                              : 0 (Default)
Write Long with Retry and without Retry              : 0 (Default)
Max SATA Link Rate                                   : 0 (Default)
Deterministic Trim Setting                           : 0 (Default)
Controller Drive Strength Rate                       : 0 (Default)
PHY Setting                                          : 0 (Default)
Controller Slew Rate                                 : 0 (Default)
Put SIG FIS Delay                                    : 0 (Default)
Set Multiple Handling                                : 0 (Default)
TRIM Timer Abort                                     : 0 (Enable(Default))
Trim Support/Setting Word 169 Bit 0                  : 0 (Default(Firmware default setting))
RDD1 Optimization                                    : 0 (Default)
Security Unlock Drive                                : 0 (Default(Compare Master Password))

Power Throttling Options
Average Power Level 0-100                            : 0
Maximum Power Level 0-100                            : 0
Power Throttling Upon Unsafe Shutdown                : 0 (Default)

Dynamic Read Scrub
Read Scrub Enabled                                   : 0 (Default (Enabled))
Dynamic Read Scrub End Range1                        : 0
Dynamic Read Scrub Rate Range1                       : 0
Dynamic Read Scrub End Range2                        : 0
Dynamic Read Scrub Rate Range2                       : 0
Dynamic Read Scrub End Range3                        : 0
Dynamic Read Scrub Rate Range3                       : 0
Dynamic Read Scrub End Range4                        : 0
Dynamic Read Scrub Rate Range4                       : 0

Low Level Format Settings
Number of entries in Max LBA Setting                 : 0

Host Protected Area
Host Protected Access                                : 0 (Always Reset HPA State On COMRESET)

End of Life Behavior
Enable End of Life                                   : 0 (Default (EOL Enabled))
EOL Threshold 1 Type                                 : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage                           : 0
EOL Threshold 1 Behavior                             : 0 (Default (Light Write Throttling))
EOL Threshold 2 Type                                 : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage                           : 0
EOL Threshold 1 Behavior                             : 0 (Default (Heavy Write Throttling))

CDU Smart settings: default

Fab Defect list entry : 0

User Defect list entry: 0

Panic Dumps   : 0
Panic Dumps list:
Idx Accurev SyncCode UnlockLevel  Size DataSize EPA        Log Ok CRC Ok
0  1129404 0xfdffa6f9 0xffffff00  3388  2952672 0x00040002 0x0000 0x0000
1  1129404 0xfdffa6f9 0xffffff00  3388  2952672 0x20040002 0x0000 0x0000
2        0 0x00000000 0x00000000     0        0 0x00040102 0x0000 0x0000
3        0 0x00000000 0x00000000     0        0 0x20040102 0x0000 0x0000

MST settings not exist.

MST result not exits.