Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- Starting kernel ...
- LINUX started...
- Linux version 3.4.110 (padavan@hms) (gcc version 4.4.7 (GCC) ) #1 Mon Feb 1 02:10:25 KRAT 2016
- MediaTek SoC: MT7620A, RevID: 0206, RAM: DDR2, XTAL: 20MHz
- CPU/OCP/SYS frequency: 600/200/200 MHz
- CPU revision is: 00019650 (MIPS 24KEc)
- Determined physical RAM map:
- memory: 04000000 @ 00000000 (usable)
- Zone PFN ranges:
- Normal 0x00000000 -> 0x00004000
- Movable zone start PFN for each node
- Early memory PFN ranges
- 0: 0x00000000 -> 0x00004000
- Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- Kernel command line: console=ttyS0,115200n8 root=/dev/mtdblock4 rootfstype=squashfs
- PID hash table entries: 256 (order: -2, 1024 bytes)
- Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- Writing ErrCtl register=0007623e
- Readback ErrCtl register=0007623e
- Memory: 61464k/65536k available (2761k kernel code, 4072k reserved, 414k data, 212k init, 0k highmem)
- NR_IRQS:40
- console [ttyS0] enabled
- Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 512
- NET: Registered protocol family 16
- PCIe0: no card, disable it (RST&CLK)
- bio: create slab <bio-0> at 0
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- Switching to clocksource MIPS
- NET: Registered protocol family 2
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 2048 (order: 2, 16384 bytes)
- TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
- TCP: Hash tables configured (established 2048 bind 2048)
- TCP: reno registered
- UDP hash table entries: 256 (order: 0, 4096 bytes)
- NET: Registered protocol family 1
- squashfs: version 4.0 (2009/01/31) Phillip Lougher
- msgmni has been set to 120
- io scheduler noop registered (default)
- Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
- serial8250: ttyS0 at MMIO 0x10000c00 (irq = 12) is a 16550A
- Ralink GPIO driver initialized. Number of GPIO: 73, GPIO mode: 0078111D
- loop: module loaded
- Ralink SPI flash driver, SPI clock: 50MHz
- SPI flash chip: W25Q128FV (ef 40180000) (16384 Kbytes)
- Creating 7 MTD partitions on "raspi":
- 0x000000000000-0x000000030000 : "Bootloader"
- 0x000000030000-0x000000040000 : "Config"
- 0x000000040000-0x000000050000 : "Factory"
- 0x000000050000-0x00000016e290 : "Kernel"
- 0x00000016e290-0x000000fc0000 : "RootFS"
- 0x000000fc0000-0x000001000000 : "Storage"
- 0x000000050000-0x000000fc0000 : "Firmware_Stub"
- tun: Universal TUN/TAP device driver, 1.6
- tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- Ralink APSoC Ethernet Driver v3.2.2 (raeth)
- raeth: PDMA RX ring 256, PDMA TX ring 512. Max packet size 1536
- raeth: NAPI support, weight 32
- raeth: Byte Queue Limits (BQL) support
- PPP generic driver version 2.4.2
- PPP MPPE Compression module registered
- NET: Registered protocol family 24
- PPTP driver version 0.8.5
- usbcore: registered new interface driver libusual
- nf_conntrack version 0.5.0 (16384 buckets, 32768 max)
- xt_time: kernel timezone is -0000
- Bridge firewalling registered
- gre: GRE over IPv4 demultiplexor driver
- ip_tables: (C) 2000-2006 Netfilter Core Team
- TCP: cubic registered
- NET: Registered protocol family 10
- ip6_tables: (C) 2000-2006 Netfilter Core Team
- IPv6 over IPv4 tunneling driver
- NET: Registered protocol family 17
- L2TP core driver, V2.0
- PPPoL2TP kernel driver, V2.0
- 8021q: 802.1Q VLAN Support v1.8
- ASUS NVRAM, v0.08. Available space: 61440. Integrity: OK
- VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
- Freeing unused kernel memory: 212k freed
- Algorithmics/MIPS FPU Emulator v1.5
- validate subfs:
Add Comment
Please, Sign In to add comment