Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 1.1.4-g30d8afa8-dirty (Nov 1 2016 - 17:38:05)
- ap143-2.0 - Honey Bee 2.0
- DRAM: 64 MB
- Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x17
- flash size 8MB, sector count = 128
- Flash: 8 MB
- Using default environment
- In: serial
- Out: serial
- Err: serial
- Net: ath_gmac_enet_initialize...
- ath_gmac_enet_initialize: reset mask:c02200
- Scorpion ---->S27 PHY*
- S27 reg init
- : cfg1 0x800c0000 cfg2 0x7114
- eth0: ba:be:fa:ce:08:41
- athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
- athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
- eth0 up
- Honey Bee ----> MAC 1 S27 PHY *
- S27 reg init
- ATHRS27: resetting s27
- ATHRS27: s27 reset done
- : cfg1 0x800c0000 cfg2 0x7214
- eth1: ba:be:fa:ce:08:41
- athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
- athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
- athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
- athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
- athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
- athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
- athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
- athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
- eth1 up
- eth0, eth1
- Setting 0x181162c0 to 0x50a1a100
- is button pressed? 0
- Autobooting in 1 seconds
- ## Booting image at 9f040000 ...
- Uncompressing Kernel Image ... OK
- Starting kernel ...
- [ 0.000000] Linux version 4.4.92 (robimarko@Builder) (gcc version 5.5.0 (LEDE GCC 5.5.0 r5108-458b996) ) #0 Sun Oct 15 14:47:38 2017
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
- [ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] No valid device tree found, continuing without
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- [ 0.000000] Kernel command line: board=CPE210V2 mtdparts=spi0.0:128k(u-boot)ro,64k(pation-table)ro,64k(product-info)ro,1536k(kernel),6144k(rootfs),192k(config)ro,64k(ART)ro,7680k@0x40000(firmware) console=ttyS0,115200 rootfstype=squashfs noinitrd
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Writing ErrCtl register=00000000
- [ 0.000000] Readback ErrCtl register=00000000
- [ 0.000000] Memory: 60100K/65536K available (2996K kernel code, 144K rwdata, 756K rodata, 320K init, 200K bss, 5436K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:51
- [ 0.000000] Clocks: CPU:650.000MHz, DDR:390.722MHz, AHB:216.666MHz, Ref:25.000MHz
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns
- [ 0.000009] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns
- [ 0.008249] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)
- [ 0.071113] pid_max: default: 32768 minimum: 301
- [ 0.076130] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.083111] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.093845] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.104282] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.111599] NET: Registered protocol family 16
- [ 0.118126] MIPS: machine is TP-LINK CPE210 v2
- [ 0.350677] clocksource: Switched to clocksource MIPS
- [ 0.357602] NET: Registered protocol family 2
- [ 0.363146] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.370516] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.377304] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.384149] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.390331] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.397369] NET: Registered protocol family 1
- [ 0.407234] Crashlog allocated RAM at address 0x3f00000
- [ 0.429156] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.435397] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.448798] io scheduler noop registered
- [ 0.453014] io scheduler deadline registered (default)
- [ 0.458765] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
- [ 0.466007] console [ttyS0] disabled
- [ 0.489944] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
- [ 0.499057] console [ttyS0] enabled
- [ 0.499057] console [ttyS0] enabled
- [ 0.506611] bootconsole [early0] disabled
- [ 0.506611] bootconsole [early0] disabled
- [ 0.519104] m25p80 spi0.0: found gd25q64, expected m25p80
- [ 0.524793] m25p80 spi0.0: gd25q64 (8192 Kbytes)
- [ 0.529600] 8 cmdlinepart partitions found on MTD device spi0.0
- [ 0.535726] Creating 8 MTD partitions on "spi0.0":
- [ 0.540695] 0x000000000000-0x000000020000 : "u-boot"
- [ 0.548687] 0x000000020000-0x000000030000 : "pation-table"
- [ 0.556397] 0x000000030000-0x000000040000 : "product-info"
- [ 0.564084] 0x000000040000-0x0000001c0000 : "kernel"
- [ 0.571162] 0x0000001c0000-0x0000007c0000 : "rootfs"
- [ 0.578202] mtd: device 4 (rootfs) set to be root filesystem
- [ 0.584199] 1 squashfs-split partitions found on MTD device rootfs
- [ 0.590598] 0x0000003b0000-0x0000007c0000 : "rootfs_data"
- [ 0.598106] 0x0000007c0000-0x0000007f0000 : "config"
- [ 0.605296] 0x0000007f0000-0x000000800000 : "ART"
- [ 0.612169] 0x000000040000-0x0000007c0000 : "firmware"
- [ 0.645242] libphy: ag71xx_mdio: probed
- [ 1.233635] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
- [ 1.243880] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
- [ 1.252541] NET: Registered protocol family 10
- [ 1.261693] NET: Registered protocol family 17
- [ 1.266386] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 1.279635] 8021q: 802.1Q VLAN Support v1.8
- [ 1.293332] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
- [ 1.303448] Freeing unused kernel memory: 320K
- [ 2.252988] init: Console is alive
- [ 2.256774] init: - watchdog -
- [ 3.170594] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 3.252573] usbcore: registered new interface driver usbfs
- [ 3.258340] usbcore: registered new interface driver hub
- [ 3.264034] usbcore: registered new device driver usb
- [ 3.275867] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 3.284689] ehci-platform: EHCI generic platform driver
- [ 3.293558] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 3.301665] ohci-platform: OHCI generic platform driver
- [ 3.307989] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 3.326126] init: - preinit -
- [ 3.872463] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 6.244201] eth0: link up (100Mbps/Full duplex)
- [ 6.248934] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- [ 7.107222] jffs2: notice: (367) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 7.126657] mount_root: switching to jffs2 overlay
- [ 7.157878] urandom-seed: Seeding with /etc/urandom.seed
- [ 7.364003] eth0: link down
- [ 7.383821] procd: - early -
- [ 7.386932] procd: - watchdog -
- [ 8.009944] procd: - watchdog -
- [ 8.013597] procd: - ubus -
- [ 8.054917] random: ubusd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
- [ 8.068516] random: ubusd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
- [ 8.078477] random: ubusd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
- [ 8.087880] random: ubusd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
- [ 8.097519] random: ubusd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
- [ 8.106889] random: ubusd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
- [ 8.117096] random: ubusd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
- [ 8.126650] random: ubusd: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
- [ 8.136477] procd: - init -
- Please press Enter to activate this console.
- [ 8.529899] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 8.542866] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 8.565010] Loading modules backported from Linux version wt-2017-10-06-0-ga7a22fbbd1f0
- [ 8.573375] Backport generated by backports.git v4.14-rc2-1-6-gedfb595c
- [ 8.584319] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 8.599844] nf_conntrack version 0.5.0 (944 buckets, 3776 max)
- [ 8.665787] xt_time: kernel timezone is -0000
- [ 8.743477] PPP generic driver version 2.4.2
- [ 8.751719] NET: Registered protocol family 24
- [ 8.832207] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47
- [ 8.951841] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 10.035203] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
- [ 10.119618] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
- [ 16.235126] device eth0 entered promiscuous mode
- [ 16.250983] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
- [ 17.860935] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 18.088185] device wlan0 entered promiscuous mode
- [ 18.284205] eth0: link up (100Mbps/Full duplex)
- [ 18.288966] br-lan: port 1(eth0) entered forwarding state
- [ 18.294660] br-lan: port 1(eth0) entered forwarding state
- [ 18.301319] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
- [ 20.290686] br-lan: port 1(eth0) entered forwarding state
Add Comment
Please, Sign In to add comment