Welcome to minicom 2.7.1

OPTIONS:
Compiled on Oct  6 2019, 23:16:03.
Port /dev/tty.SLAB_USBtoUART, 19:41:51

Press Meta-Z for help on special keys


BCM74130011
012
K1
K2

K3

K4

K5

Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000004
WC1=FFFFFFF6
RC2=00000018
WC2=00000043
RC3=0000000E
WC3=FFFFFFF6
RC4=0000000E
WC4=00000043
NWC=0000001C
RC5=00000004
WC5=0000001C
RC6=00000018
WC6=0000001C
NRC=0000000E
RW=00000015
WW=0000004E
G=00000000 R=0000000E W=0000001C
BL=00000000
RC1=00000001
RC2=00000015

BL=00000001
RC1=00000002
RC2=00000018

BL=00000002
RC1=00000002
RC2=00000017

BL=00000003
RC1=00000005
RC2=00000017

BL=00000004
RC1=00000001
RC2=00000017

BL=00000005
RC1=00000002
RC2=00000018

BL=00000006
RC1=00000001
RC2=00000015

BL=00000007
RC1=00000004
RC2=00000017
3
PBL=10.1.1-pbl
COPY_CODE
00056918
A279615D
4567

BCM97413B1 CFE v2.26, core v2.12, PBL: 10.5.0-pbl, Endian Mode: Little
Build Date: Tue Sep 25 16:15:20 HKT 2012 (kelvin.chan@Kelvin-Fedora11)
Copyright (C) Broadcom Corporation.

NOR boot: Detecting NAND flash at CS1...
NAND device id = 0xECDA1095
Enabling NAND flash
Disabling the XOR address inversion. Not suitable for BBS (refer: xor command)
XOR setting 0x0
[ WARNING ]: Assuming NVRAM address same as Kamai (NOR Boot 4MB + NAND 128MB)
Loading NVRAM at NOR flash 0x00320000

DDR Freq        396MHz
CPU speed       405MHz
Memory Config   64-bit UMA
Device Tech     1Gb
Total memory    512MB
Boot Device     NOR
NAND flash      256MB
NOR flash       4MB

Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub

CFE initialized.
Found MCU_IRQ_OUT = 22
MCU IRQ_OUT pin GPIO 22 = 1
Starting splash screen (PAL).

Splash Image Type: PNG
PNG Info - Width = 720 Height = 576

Executing automatic system init:
 - <waitusb -o -d="USB Disk" && batch -e usbdisk0:/recovery/7405/start.txt || batch -e usbdisk1:/recovery/7405/start.txt>
No USB devices found!
Executing STARTUP...
bbl1 and bbl2 are shared, skipping bbl1
Loader:elf Filesys:raw Dev:nand0.appkernel File: Options:nvram=nor,0x320000 boot_dev=cfe active_module=app
Loading: !!!!! UNC read error occurred, while reading from NAND flash
Valid Image found!
0x80001000/7923264 0x8078f640/130384 load_program : 0
Entry address is 0x80005470
TP1 Entry Address at 0x80000ffc = 80005470
Starting program at 0x80005470

Linux version 2.6.31-3.2 (jack.yu@jack.yu.entone) (gcc version 4.4.5 (Broadcom stbgcc-4.4.5-2.0) ) #2 SMP Mon Mar 4 14:40:48 HKT 2013
Fetching vars from bootloader... found 6 vars.
Early serial console at MMIO 0x10400b00 (options '115200n8')
console [uart0] enabled
Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1
Using 512 MB + 0 MB RAM (from CFE)
CPU revision is: 0002a044 (Broadcom BMIPS4380)
FPU revision is: 00130001
Determined physical RAM map:
 memory: 10000000 @ 00000000 (usable)
 memory: 10000000 @ 20000000 (usable)
bmem: adding 224 MB RESERVED region at 32 MB (0x0e000000@0x02000000)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00030000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0: 0x00000000 -> 0x00010000
    0: 0x00020000 -> 0x00030000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 129536
Kernel command line: nvram=nor,0x320000 boot_dev=cfe active_module=app
PID hash table entries: 2048 (order: 11, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
Memory: 282116k/524288k available (3848k kernel code, 241792k reserved, 805k data, 3084k init, 0k highmem)
NR_IRQS:128
Detected MIPS clock frequency: 404 MHz (202.497 MHz counter)
Calibrating delay loop... 404.48 BogoMIPS (lpj=202240)
Mount-cache hash table entries: 512
[BLINK LED] blink_led.color not found!
[BLINK LED] blink_led device registered with major 253
SMP: Booting CPU1...
CPU revision is: 0002a044 (Broadcom BMIPS4380)
FPU revision is: 00130001
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
Calibrating delay loop... 406.52 BogoMIPS (lpj=203264)
SMP: CPU1 is running
Brought up 2 CPUs
NET: Registered protocol family 16
PCI2.3->SDRAM window: 512 MB
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
JFFS2 version 2.2. (NAND) (SUMMARY)  ?© 2001-2006 Red Hat, Inc.
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 551
io scheduler noop registered
io scheduler anticipatory registered (default)

Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
console handover: boot [uart0] -> real [ttyS0]
serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A
brd: module loaded
loop: module loaded
brcm-pm: enabling sata clocks
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
bcmemac: Broadcom STB 10/100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:00:de:ad:be:ef)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver cdc_subset
Broadcom 9xxxx mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
NOR chip too large to fit in mapping. Attempting to cope...
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Reducing visibility of 4096KiB chip to 2048KiB
[ENTONE] BCM97XXX Flash Size from CFI: 0x400000
[ENTONE] BCM97XXX Flash Device: 0x400000 bytes @ 0x1fc00000
Broadcom 9xxxx mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
[ENTONE] Delay adding NOR partitions until NAND driver is initialized (0xcf2bac00)
Broadcom STB NAND controller (BrcmNand Controller)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
brcm-pm: enabling usb clocks
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
ata1: SATA link down (SStatus 4 SControl 300)
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
TCP cubic registered
NET: Registered protocol family 17
Bridge firewalling registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
warning: unable to build a flash partition map, using entire device
EBI CS0: setting up NOR flash (primary)
EBI CS1: setting up NAND flash
[ENTONE] BRCM NAND controller version = 3.2
i=1, CS[0] = 1
NAND_CS_NAND_XOR=00000000
Disabling XOR on CS#1
B4: NandSelect=50000200, nandConfig=16152300, chipSelect=1
brcmnand_probe: CS1: dev_id=ecda1095
After: NandSelect=50000200, nandConfig=16152300
NAND Config: Reg=16152300, chipSize=256 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
BrcmNAND mfg ec da Samsung K9F2G08U0A 256MB

Found NAND: ACC=d7ff1010, cfg=16152300, flashId=ecda1095, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0302 256MB @00000000
B4: NandSelect=50000200, nandConfig=16152300, chipSelect=1
brcmnand_probe: CS1: dev_id=ecda1095
After: NandSelect=50000200, nandConfig=16152300
Found NAND chip on Chip Select 1, chipSize=256MB, usable size=256MB, base=0
brcmnand_scan: B4 nand_select = 50000200
brcmnand_scan: After nand_select = 50000200
ACC_CONTROL for SLC NAND: d7ff1010, eccLevel=15
SLC flash: ACC_CONTROL = d7ff1010
page_shift=11, bbt_erase_shift=17, chip_shift=28, phys_erase_shift=17
Brcm NAND controller version = 3.2 NAND flash size 256MB @10000000
mtd->oobsize=64, mtd->eccOobSize=16
brcmnand_scan:  mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
brcmnand_default_bbt: bbt_td = bbt_main_descr
        numchips=1, size=10000000
[ENTONE NAND] gEntoneNandFlashMtd (0xcf34c800)
[ENTONE] BBT uses 1MB flash.
Creating 1 MTD partitions on "Broadcom 9xxxx mapped flash":
0x000000000000-0x000000020000 : "nor0.bep"
Creating 1 MTD partitions on "Broadcom 9xxxx mapped flash":
0x000000020000-0x0000000a0000 : "nor0.otpdata"
Creating 1 MTD partitions on "Broadcom 9xxxx mapped flash":
0x000000160000-0x000000220000 : "nor0.cfe1"
ata2: SATA link down (SStatus 4 SControl 300)
Creating 1 MTD partitions on "Broadcom 9xxxx mapped flash":
0x0000000a0000-0x000000160000 : "nor0.cfe2"
Creating 1 MTD partitions on "Broadcom 9xxxx mapped flash":
0x000000220000-0x0000002a0000 : "nor0.upgradedata"
Creating 1 MTD partitions on "Broadcom 9xxxx mapped flash":
0x000000320000-0x0000003c0000 : "nor0.nvram"
Creating 1 MTD partitions on "Broadcom 9xxxx mapped flash":
0x0000003c0000-0x000000400000 : "nor0.empty"
Creating 1 MTD partitions on "brcmnand.0":
0x000000400000-0x000000e00000 : "nand0.persist"
Creating 1 MTD partitions on "Broadcom 9xxxx mapped flash":
0x0000002a0000-0x000000320000 : "nor0.splash"
Creating 1 MTD partitions on "brcmnand.0":
0x000000e00000-0x000001400000 : "nand0.bblkernel1"
Creating 1 MTD partitions on "brcmnand.0":
0x000001400000-0x000002800000 : "nand0.bblrootfs1"
Creating 1 MTD partitions on "brcmnand.0":
0x000000e00000-0x000001400000 : "nand0.bblkernel2"
Creating 1 MTD partitions on "brcmnand.0":
0x000001400000-0x000002800000 : "nand0.bblrootfs2"
Creating 1 MTD partitions on "brcmnand.0":
0x000002800000-0x000002e00000 : "nand0.appkernel"
Creating 1 MTD partitions on "brcmnand.0":
0x000002e00000-0x00000ff00000 : "nand0.approotfs"
Freeing unused kernel memory: 3084k freed
Default active_module=bbl
CFE passed active_module=app to kernel
Override active_module=app
Init ...
kernel header byte: 0000
press any key to stop autobooting process...
*********
Auto boot
*********

jffs2_scan_inode_node(): CRC failed on node at 0x007af7f4: Read 0xffffffff, calculated 0x1490a44b
Empty flash at 0x007af838 ends at 0x007b0000
persist: checking jffs2 filesystem...
persist: filesystem check passed
*** Check /mnt/persist/app.info ***
*** Kernel and rootfs valid, continuing...
*** Mounting RootFS /dev/mtdblock14
*** ROOT_FS_TYPE=jffs2 ***
*** Mounting rootfs as jffs2... ***
mount -t jffs2 -o noatime,nodiratime,ro /dev/mtdblock14 /mnt/rootfs
*** Mount success ***
*** switch_root to new root and run init...
Setting default system time
Sun Jan  1 00:00:00 UTC 2012
jffs2_scan_inode_node(): CRC failed on node at 0x007af7f4: Read 0xffffffff, calculated 0x1490a44b
Empty flash at 0x007af838 ends at 0x007b0000

Extract local identinfo from flash
[gentaginfo] Start now for BBL
[gentaginfo] Start now for BBL2
[gentaginfo] Start now for APP
[gentaginfo] Start now for PBL
[gentaginfo] Start now for PBL2
[gentaginfo] End
PBL: 10.5.0-pbl
BBL: 10.5.2-bbl--tr069
APP: 10.5.109.2-etv-vma--sunrise--qtwebkit--VQE
******************** fsinit 7.45 ********************
Load system kb success from blk2
Version: 109dbae7be
gpg keyrings are found
Use device specific X509 identity
******************** Checking validity of sys_config 7.81 ********************
sys_config.txt is OK, continue booting...
******************** Merge defaults 7.83 ********************
/mnt/persist/sys_config.txt already has all the necessary fields!
******************** Done merging 7.96 ********************
******************** load sys_config 8.08 ********************
*** Chipset BCM7413b1 ***
*** Platform Family BCM74xx ***
*** Linux Kernel 2.6.31 is used ***
uptime init success
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
fuse init (API version 7.12)
ini_helper.sh: Backup /tmp/dhcpc/entone_boot.ini => /tmp/dhcpc/entone_boot.ini.bak
ini_helper.sh: Merging with /usr/share/init/default_entone_boot.ini
hdmi_hotplug_mode_follow_ini=1
nexus: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
*** 00:00:00.000 nexus_driver: >>nexus_driver_init
Starting fusion driver v8.9.0
  -> initializing shared area at cf325000
Creating virtual network device
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
******************** init_entone_mediaplayer 15.31 ********************
Waiting for entone_mediaplayer ...
******************** init_hwblk 29.11 ********************
*** readhwblk now ***
HW Config Block
Version: 1
ESN: 1908566
HW Model: 20
Board Version: A1 - 200
******************** init_detect_board 29.40 ********************
####### Determining Board type #######
Amulet G1/4xx
####### Done Determining Board type #######
******************** Run video_system_detect  29.51 ********************
******************** init_display 29.54 ********************
init_display
Standard GPIO (Default)
Input GPIO
GPIO 96 status: 0
####### Determining External RF modulator #######
External RFM not detected.
####### Done Determining External RF modulator #######
Checking video frequency for single mode!
for Europe
Pal Box, need detect scart switch
init scart for amluetg1
done init_board
Nickname=amuletg1-19085661
=============================== MCU Setting =============================
model=AmuletG1(20): upMethod=ALPHA_NETWORK(2), i2cPort=2, i2cAddr=0x92(0x49)
-> upMethod=2, i2cPort[2](gI2cHandle)=OK, i2cAddr=0x92
=========================================================================
=============================== MCU Setting =============================
model=AmuletG1(20): upMethod=ALPHA_NETWORK(2), i2cPort=2, i2cAddr=0x92(0x49)
-> upMethod=2, i2cPort[2](gI2cHandle)=OK, i2cAddr=0x92
=========================================================================
[mcuCtrlDpMode] Wrong display mode input
******************** LinkStatus 30.25 ********************
******************** splash1 30.33 ********************
=============================== MCU Setting =============================
model=AmuletG1(20): upMethod=ALPHA_NETWORK(2), i2cPort=2, i2cAddr=0x92(0x49)
-> upMethod=2, i2cPort[2](gI2cHandle)=OK, i2cAddr=0x92
=========================================================================
=============================== MCU Setting =============================
model=AmuletG1(20): upMethod=ALPHA_NETWORK(2), i2cPort=2, i2cAddr=0x92(0x49)
-> upMethod=2, i2cPort[2](gI2cHandle)=OK, i2cAddr=0x92
=========================================================================
******************** LinkStatus 32.81 ********************
wait 2 second for dfbdraw to start
skin: en_US
commandline read: dfbdraw
commandline read: -f
commandline read: /tmp/drawcmd
(*) DirectFB/Core: Multi Application Core. (2015-09-30 07:37)
(*) Fusion/SHM: Not using MADV_REMOVE (forced)!
(*) Direct/Thread: Started 'Fusion Dispatch' (-1) [MESSAGING OTHER/OTHER 0/0] <1048576>...
(!) system_intiailize_options: 'res': unspecified!
(*) DirectFB/Graphics: Broadcom Corporation Bcmnexus Nexus 2D GFX Driver 4.2 (Broadcom Corporation)
(*) Direct/Interface: Loaded 'FT2' implementation of 'IDirectFBFont'.
Cannot find specified item PRG_BAR1
******************** Secure Init 36.27 ********************
Starting portmap: done
******************** dnsmasq  36.39 ********************
Initializing random number generator... done.
/etc/init.d/S21qtwebkitpreload: running
MCU is not PRIME
******************** MCU firmware upgrade  37.46 ********************
(*) Direct/Interface: Loaded 'Gif' implementation of 'IDirectFBVideoProvider'.
(*) Direct/Thread: Started 'GIF Video' (1653) [DEFAULT OTHER/OTHER 0/0] <1048576>...
MCU Version: 51
******************** HDD INIT 39.73 ********************
Checking /dev/mmcblk0 ...
******************** HDD NOT DETECTED 42.45 ********************
Command handler is now running
******************** Check Tuner Model 42.51 ********************
checking tuner card ...
Tuner card is NOT detected
******************** brcm_input 42.65 ********************
******************** input_dev_daemon 42.67 ********************
******************** /etc/init.d/S31netifinit  43.14 ********************
ifconfig eth0 hw ether 0003e63a3eac
******************** /etc/init.d/S31netifinit finished 45.05 ********************
******************** CG Upgrade 45.72 ********************
hpna card not inserted
ls: /usr/share/remote_assist/*.conf: No such file or directory
********* remote_assist 46.30 *********
******************** bootmenu 46.42 ********************
Cannot find the specified string TEXT_BOOTMENU_START
[getProcInfo] error opening /proc/0/status
******************** iptables 47.97 ********************
sdmonitor: Check sd dev existence = 256

[entone_bootmenu_task] Alive!
[bm_internal_setup] enTaskCreate_Ex(BMENU) returned 0
commandline read: bootmenu
(*) DirectFB/Core: Multi Application Core. (2015-09-30 07:37)
(*) Fusion/SHM: Not using MADV_REMOVE (forced)!
(*) Direct/Thread: Started 'Fusion Dispatch' (-1) [MESSAGING OTHER/OTHER 0/0] <1048576>...
(!) system_intiailize_options: 'res': unspecified!
(*) DirectFB/Graphics: Broadcom Corporation Bcmnexus Nexus 2D GFX Driver 4.2 (Broadcom Corporation)
[bm_MenuCap_init] essGetHWModel (20) success: AmuletG1
(*) Direct/Interface: Loaded 'FT2' implementation of 'IDirectFBFont'.
[bmi_screen_display] 0
[ebmInit] call eidOpenDevDrv
[main] bootmenu Start!
iptables: default
******************** /etc/init.d/S39netifdown  49.45 ********************
Stop eth0
******************** /etc/init.d/S39netifdown finished 49.94 ********************
******************** starting network 50.09 ********************
try starting network by eth
network_debug: touch_active_info IN pre_start eth eth eth0 Sun Jan  1 00:00:44 GMT 2012
network_debug: echo touch_active_info clean /var/tmp/ip_obtained
network_debug: touch_active_info OUT Sun Jan  1 00:00:44 GMT 2012
/usr/share/fonts: Ethernet cable is disconnected
eth start fail
caching, new cache contents: 34 fonts, 0 dirs
/usr/share/opera/fonts: skipping, no such directory
/usr/share/fonts: Stop eth0
Fallback to first avaliable network device and keep trying ...
try starting network by eth
network_debug: touch_active_info IN pre_start eth eth eth0 Sun Jan  1 00:00:55 GMT 2012
network_debug: echo touch_active_info clean /var/tmp/ip_obtained
network_debug: touch_active_info OUT Sun Jan  1 00:00:55 GMT 2012
caching, new cache contents: 34 fonts, 0 dirs
/usr/share/opera/fonts: skipping, no such directory
/var/cache/fontconfig: cleaning cache directory
Ethernet cable is disconnected
fc-cache: succeeded
network_debug: touch_active_info IN pre_start eth eth eth0 Sun Jan  1 00:01:01 GMT 2012
network_debug: echo touch_active_info clean /var/tmp/ip_obtained
network_debug: touch_active_info OUT Sun Jan  1 00:01:01 GMT 2012
Ethernet cable is disconnected
network_debug: touch_active_info IN pre_start eth eth eth0 Sun Jan  1 00:01:07 GMT 2012
network_debug: echo touch_active_info clean /var/tmp/ip_obtained
network_debug: touch_active_info OUT Sun Jan  1 00:01:07 GMT 2012
Ethernet cable is disconnected
network_debug: touch_active_info IN pre_start eth eth eth0 Sun Jan  1 00:01:12 GMT 2012
network_debug: echo touch_active_info clean /var/tmp/ip_obtained
network_debug: touch_active_info OUT Sun Jan  1 00:01:12 GMT 2012
Ethernet cable is disconnected
network_debug: touch_active_info IN pre_start eth eth eth0 Sun Jan  1 00:01:17 GMT 2012
network_debug: echo touch_active_info clean /var/tmp/ip_obtained
network_debug: touch_active_info OUT Sun Jan  1 00:01:17 GMT 2012
Ethernet cable is disconnected

Meta-Z for help | 115200 8N1 | NOR | Minicom 2.7.1 | VT102 | Offline | tty.SLAB_USBtoUART