API tools faq
paste
Conqy

am8 marlin 2.1.2

Conqy
Jun 25th, 2024
20
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 128.32 KB | None | 0 0
raw download clone embed print report
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <https://www.gnu.org/licenses/>.
  20. *
  21. */
  22. #pragma once
  23.  
  24. #define CONFIG_EXAMPLES_DIR "Anet/A8"
  25.  
  26. /**
  27. * Configuration.h
  28. *
  29. * Basic settings such as:
  30. *
  31. * - Type of electronics
  32. * - Type of temperature sensor
  33. * - Printer geometry
  34. * - Endstop configuration
  35. * - LCD controller
  36. * - Extra features
  37. *
  38. * Advanced settings can be found in Configuration_adv.h
  39. */
  40. #define CONFIGURATION_H_VERSION 02010200
  41.  
  42. //===========================================================================
  43. //============================= Getting Started =============================
  44. //===========================================================================
  45.  
  46. /**
  47. * Here are some useful links to help get your machine configured and calibrated:
  48. *
  49. * Example Configs: https://github.com/MarlinFirmware/Configurations/branches/all
  50. *
  51. * Průša Calculator: https://blog.prusaprinters.org/calculator_3416/
  52. *
  53. * Calibration Guides: https://reprap.org/wiki/Calibration
  54. * https://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  55. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  56. * https://youtu.be/wAL9d7FgInk
  57. *
  58. * Calibration Objects: https://www.thingiverse.com/thing:5573
  59. * https://www.thingiverse.com/thing:1278865
  60. */
  61.  
  62. // @section info
  63.  
  64. // Author info of this build printed to the host during boot and M115
  65. #define STRING_CONFIG_H_AUTHOR "(Bob Kuhn, Anet config)" // Who made the changes.
  66. //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
  67.  
  68. /**
  69. * *** VENDORS PLEASE READ ***
  70. *
  71. * Marlin allows you to add a custom boot image for Graphical LCDs.
  72. * With this option Marlin will first show your custom screen followed
  73. * by the standard Marlin logo with version number and web URL.
  74. *
  75. * We encourage you to take advantage of this new feature and we also
  76. * respectfully request that you retain the unmodified Marlin boot screen.
  77. */
  78.  
  79. // Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION **
  80. #define SHOW_BOOTSCREEN
  81.  
  82. // Show the bitmap in Marlin/_Bootscreen.h on startup.
  83. //#define SHOW_CUSTOM_BOOTSCREEN
  84.  
  85. // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
  86. //#define CUSTOM_STATUS_SCREEN_IMAGE
  87.  
  88. // @section machine
  89.  
  90. // Choose the name from boards.h that matches your setup
  91. #ifndef MOTHERBOARD
  92. #define MOTHERBOARD BOARD_BTT_SKR_V1_4 //EC
  93. #endif
  94.  
  95. /**
  96. * Select the serial port on the board to use for communication with the host.
  97. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  98. * Serial port -1 is the USB emulated serial port, if available.
  99. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  100. *
  101. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  102. */
  103. #define SERIAL_PORT -1 //EC required for BTT SKR1.4
  104.  
  105. /**
  106. * Serial Port Baud Rate
  107. * This is the default communication speed for all serial ports.
  108. * Set the baud rate defaults for additional serial ports below.
  109. *
  110. * 250000 works in most cases, but you might try a lower speed if
  111. * you commonly experience drop-outs during host printing.
  112. * You may try up to 1000000 to speed up SD file transfer.
  113. *
  114. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  115. */
  116. #define BAUDRATE 250000 //EC
  117.  
  118. //#define BAUD_RATE_GCODE // Enable G-code M575 to set the baud rate
  119.  
  120. /**
  121. * Select a secondary serial port on the board to use for communication with the host.
  122. * Currently Ethernet (-2) is only supported on Teensy 4.1 boards.
  123. * :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7]
  124. */
  125. //#define SERIAL_PORT_2 -1
  126. //#define BAUDRATE_2 250000 // :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] Enable to override BAUDRATE
  127.  
  128. /**
  129. * Select a third serial port on the board to use for communication with the host.
  130. * Currently only supported for AVR, DUE, LPC1768/9 and STM32/STM32F1
  131. * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  132. */
  133. //#define SERIAL_PORT_3 1
  134. //#define BAUDRATE_3 250000 // :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] Enable to override BAUDRATE
  135.  
  136. // Enable the Bluetooth serial interface on AT90USB devices
  137. //#define BLUETOOTH
  138.  
  139. // Name displayed in the LCD "Ready" message and Info menu
  140. #define CUSTOM_MACHINE_NAME "lA8in"
  141.  
  142. // Printer's unique ID, used by some programs to differentiate between machines.
  143. // Choose your own or use a service like https://www.uuidgenerator.net/version4
  144. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  145.  
  146. // @section stepper drivers
  147.  
  148. /**
  149. * Stepper Drivers
  150. *
  151. * These settings allow Marlin to tune stepper driver timing and enable advanced options for
  152. * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
  153. *
  154. * Use TMC2208/TMC2208_STANDALONE for TMC2225 drivers and TMC2209/TMC2209_STANDALONE for TMC2226 drivers.
  155. *
  156. * Options: A4988, A5984, DRV8825, LV8729, TB6560, TB6600, TMC2100,
  157. * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
  158. * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
  159. * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE,
  160. * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  161. * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  162. */
  163. #define X_DRIVER_TYPE TMC2209
  164. #define Y_DRIVER_TYPE TMC2209
  165. #define Z_DRIVER_TYPE TMC2209
  166. //#define X2_DRIVER_TYPE A4988
  167. //#define Y2_DRIVER_TYPE A4988
  168. //#define Z2_DRIVER_TYPE A4988
  169. //#define Z3_DRIVER_TYPE A4988
  170. //#define Z4_DRIVER_TYPE A4988
  171. //#define I_DRIVER_TYPE A4988
  172. //#define J_DRIVER_TYPE A4988
  173. //#define K_DRIVER_TYPE A4988
  174. //#define U_DRIVER_TYPE A4988
  175. //#define V_DRIVER_TYPE A4988
  176. //#define W_DRIVER_TYPE A4988
  177. #define E0_DRIVER_TYPE TMC2209
  178. //#define E1_DRIVER_TYPE A4988
  179. //#define E2_DRIVER_TYPE A4988
  180. //#define E3_DRIVER_TYPE A4988
  181. //#define E4_DRIVER_TYPE A4988
  182. //#define E5_DRIVER_TYPE A4988
  183. //#define E6_DRIVER_TYPE A4988
  184. //#define E7_DRIVER_TYPE A4988
  185.  
  186. // #define DIAG_PINS_REMOVED //EC suppresses warning about sensorless homing
  187.  
  188. /**
  189. * Additional Axis Settings
  190. *
  191. * Define AXISn_ROTATES for all axes that rotate or pivot.
  192. * Rotational axis coordinates are expressed in degrees.
  193. *
  194. * AXISn_NAME defines the letter used to refer to the axis in (most) G-code commands.
  195. * By convention the names and roles are typically:
  196. * 'A' : Rotational axis parallel to X
  197. * 'B' : Rotational axis parallel to Y
  198. * 'C' : Rotational axis parallel to Z
  199. * 'U' : Secondary linear axis parallel to X
  200. * 'V' : Secondary linear axis parallel to Y
  201. * 'W' : Secondary linear axis parallel to Z
  202. *
  203. * Regardless of these settings the axes are internally named I, J, K, U, V, W.
  204. */
  205. #ifdef I_DRIVER_TYPE
  206. #define AXIS4_NAME 'A' // :['A', 'B', 'C', 'U', 'V', 'W']
  207. #define AXIS4_ROTATES
  208. #endif
  209. #ifdef J_DRIVER_TYPE
  210. #define AXIS5_NAME 'B' // :['B', 'C', 'U', 'V', 'W']
  211. #define AXIS5_ROTATES
  212. #endif
  213. #ifdef K_DRIVER_TYPE
  214. #define AXIS6_NAME 'C' // :['C', 'U', 'V', 'W']
  215. #define AXIS6_ROTATES
  216. #endif
  217. #ifdef U_DRIVER_TYPE
  218. #define AXIS7_NAME 'U' // :['U', 'V', 'W']
  219. //#define AXIS7_ROTATES
  220. #endif
  221. #ifdef V_DRIVER_TYPE
  222. #define AXIS8_NAME 'V' // :['V', 'W']
  223. //#define AXIS8_ROTATES
  224. #endif
  225. #ifdef W_DRIVER_TYPE
  226. #define AXIS9_NAME 'W' // :['W']
  227. //#define AXIS9_ROTATES
  228. #endif
  229.  
  230. // @section extruder
  231.  
  232. // This defines the number of extruders
  233. // :[0, 1, 2, 3, 4, 5, 6, 7, 8]
  234. #define EXTRUDERS 1
  235.  
  236. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  237. // The Anet A8 original extruder is designed for 1.75mm
  238. #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
  239.  
  240. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  241. //#define SINGLENOZZLE
  242.  
  243. // Save and restore temperature and fan speed on tool-change.
  244. // Set standby for the unselected tool with M104/106/109 T...
  245. #if ENABLED(SINGLENOZZLE)
  246. //#define SINGLENOZZLE_STANDBY_TEMP
  247. //#define SINGLENOZZLE_STANDBY_FAN
  248. #endif
  249.  
  250. // @section multi-material
  251.  
  252. /**
  253. * Multi-Material Unit
  254. * Set to one of these predefined models:
  255. *
  256. * PRUSA_MMU1 : Průša MMU1 (The "multiplexer" version)
  257. * PRUSA_MMU2 : Průša MMU2
  258. * PRUSA_MMU2S : Průša MMU2S (Requires MK3S extruder with motion sensor, EXTRUDERS = 5)
  259. * EXTENDABLE_EMU_MMU2 : MMU with configurable number of filaments (ERCF, SMuFF or similar with Průša MMU2 compatible firmware)
  260. * EXTENDABLE_EMU_MMU2S : MMUS with configurable number of filaments (ERCF, SMuFF or similar with Průša MMU2 compatible firmware)
  261. *
  262. * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
  263. * See additional options in Configuration_adv.h.
  264. * :["PRUSA_MMU1", "PRUSA_MMU2", "PRUSA_MMU2S", "EXTENDABLE_EMU_MMU2", "EXTENDABLE_EMU_MMU2S"]
  265. */
  266. //#define MMU_MODEL PRUSA_MMU2
  267.  
  268. // A dual extruder that uses a single stepper motor
  269. //#define SWITCHING_EXTRUDER
  270. #if ENABLED(SWITCHING_EXTRUDER)
  271. #define SWITCHING_EXTRUDER_SERVO_NR 0
  272. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  273. #if EXTRUDERS > 3
  274. #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  275. #endif
  276. #endif
  277.  
  278. // A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles
  279. //#define SWITCHING_NOZZLE
  280. #if ENABLED(SWITCHING_NOZZLE)
  281. #define SWITCHING_NOZZLE_SERVO_NR 0
  282. //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
  283. #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
  284. #define SWITCHING_NOZZLE_SERVO_DWELL 2500 // Dwell time to wait for servo to make physical move
  285. #endif
  286.  
  287. /**
  288. * Two separate X-carriages with extruders that connect to a moving part
  289. * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  290. */
  291. //#define PARKING_EXTRUDER
  292.  
  293. /**
  294. * Two separate X-carriages with extruders that connect to a moving part
  295. * via a magnetic docking mechanism using movements and no solenoid
  296. *
  297. * project : https://www.thingiverse.com/thing:3080893
  298. * movements : https://youtu.be/0xCEiG9VS3k
  299. * https://youtu.be/Bqbcs0CU2FE
  300. */
  301. //#define MAGNETIC_PARKING_EXTRUDER
  302.  
  303. #if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
  304.  
  305. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
  306. #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
  307.  
  308. #if ENABLED(PARKING_EXTRUDER)
  309.  
  310. #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
  311. #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
  312. #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
  313. //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
  314.  
  315. #elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
  316.  
  317. #define MPE_FAST_SPEED 9000 // (mm/min) Speed for travel before last distance point
  318. #define MPE_SLOW_SPEED 4500 // (mm/min) Speed for last distance travel to park and couple
  319. #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
  320. #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
  321.  
  322. #endif
  323.  
  324. #endif
  325.  
  326. /**
  327. * Switching Toolhead
  328. *
  329. * Support for swappable and dockable toolheads, such as
  330. * the E3D Tool Changer. Toolheads are locked with a servo.
  331. */
  332. //#define SWITCHING_TOOLHEAD
  333.  
  334. /**
  335. * Magnetic Switching Toolhead
  336. *
  337. * Support swappable and dockable toolheads with a magnetic
  338. * docking mechanism using movement and no servo.
  339. */
  340. //#define MAGNETIC_SWITCHING_TOOLHEAD
  341.  
  342. /**
  343. * Electromagnetic Switching Toolhead
  344. *
  345. * Parking for CoreXY / HBot kinematics.
  346. * Toolheads are parked at one edge and held with an electromagnet.
  347. * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4
  348. */
  349. //#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD
  350.  
  351. #if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  352. #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock
  353. #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis
  354. #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis
  355. #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders
  356. #if ENABLED(SWITCHING_TOOLHEAD)
  357. #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector
  358. #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock
  359. #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD)
  360. #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis
  361. #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1)
  362. //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock
  363. #if ENABLED(PRIME_BEFORE_REMOVE)
  364. #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length
  365. #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length
  366. #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/min) Extruder prime feedrate
  367. #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/min) Extruder retract feedrate
  368. #endif
  369. #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
  370. #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching
  371. #endif
  372. #endif
  373.  
  374. /**
  375. * "Mixing Extruder"
  376. * - Adds G-codes M163 and M164 to set and "commit" the current mix factors.
  377. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  378. * - Optional support for Repetier Firmware's 'M164 S<index>' supporting virtual tools.
  379. * - This implementation supports up to two mixing extruders.
  380. * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation).
  381. */
  382. //#define MIXING_EXTRUDER
  383. #if ENABLED(MIXING_EXTRUDER)
  384. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  385. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  386. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  387. //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD
  388. //#define MIXING_PRESETS // Assign 8 default V-tool presets for 2 or 3 MIXING_STEPPERS
  389. #if ENABLED(GRADIENT_MIX)
  390. //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias
  391. #endif
  392. #endif
  393.  
  394. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  395. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  396. // For the other hotends it is their distance from the extruder 0 hotend.
  397. //#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle
  398. //#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
  399. //#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
  400.  
  401. // @section psu control
  402.  
  403. /**
  404. * Power Supply Control
  405. *
  406. * Enable and connect the power supply to the PS_ON_PIN.
  407. * Specify whether the power supply is active HIGH or active LOW.
  408. */
  409. //#define PSU_CONTROL
  410. //#define PSU_NAME "Power Supply"
  411.  
  412. #if ENABLED(PSU_CONTROL)
  413. //#define MKS_PWC // Using the MKS PWC add-on
  414. //#define PS_OFF_CONFIRM // Confirm dialog when power off
  415. //#define PS_OFF_SOUND // Beep 1s when power off
  416. #define PSU_ACTIVE_STATE LOW // Set 'LOW' for ATX, 'HIGH' for X-Box
  417.  
  418. //#define PSU_DEFAULT_OFF // Keep power off until enabled directly with M80
  419. //#define PSU_POWERUP_DELAY 250 // (ms) Delay for the PSU to warm up to full power
  420. //#define LED_POWEROFF_TIMEOUT 10000 // (ms) Turn off LEDs after power-off, with this amount of delay
  421.  
  422. //#define POWER_OFF_TIMER // Enable M81 D<seconds> to power off after a delay
  423. //#define POWER_OFF_WAIT_FOR_COOLDOWN // Enable M81 S to power off only after cooldown
  424.  
  425. //#define PSU_POWERUP_GCODE "M355 S1" // G-code to run after power-on (e.g., case light on)
  426. //#define PSU_POWEROFF_GCODE "M355 S0" // G-code to run before power-off (e.g., case light off)
  427.  
  428. //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin
  429. #if ENABLED(AUTO_POWER_CONTROL)
  430. #define AUTO_POWER_FANS // Turn on PSU if fans need power
  431. #define AUTO_POWER_E_FANS
  432. #define AUTO_POWER_CONTROLLERFAN
  433. #define AUTO_POWER_CHAMBER_FAN
  434. #define AUTO_POWER_COOLER_FAN
  435. #define POWER_TIMEOUT 30 // (s) Turn off power if the machine is idle for this duration
  436. //#define POWER_OFF_DELAY 60 // (s) Delay of poweroff after M81 command. Useful to let fans run for extra time.
  437. #endif
  438. #if EITHER(AUTO_POWER_CONTROL, POWER_OFF_WAIT_FOR_COOLDOWN)
  439. //#define AUTO_POWER_E_TEMP 50 // (°C) PSU on if any extruder is over this temperature
  440. //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) PSU on if the chamber is over this temperature
  441. //#define AUTO_POWER_COOLER_TEMP 26 // (°C) PSU on if the cooler is over this temperature
  442. #endif
  443. #endif
  444.  
  445. //===========================================================================
  446. //============================= Thermal Settings ============================
  447. //===========================================================================
  448. // @section temperature
  449.  
  450. /**
  451. * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  452. *
  453. * Temperature sensors available:
  454. *
  455. * SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
  456. * -------
  457. * -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
  458. * NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
  459. * -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
  460. * -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
  461. *
  462. * NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
  463. * Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
  464. * Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
  465. * Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
  466. *
  467. * Analog Themocouple Boards
  468. * -------
  469. * -4 : AD8495 with Thermocouple
  470. * -1 : AD595 with Thermocouple
  471. *
  472. * Analog Thermistors - 4.7kΩ pullup - Normal
  473. * -------
  474. * 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
  475. * 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
  476. * 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
  477. * 2 : 200kΩ ATC Semitec 204GT-2
  478. * 202 : 200kΩ Copymaster 3D
  479. * 3 : ???Ω Mendel-parts thermistor
  480. * 4 : 10kΩ Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
  481. * 5 : 100kΩ ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
  482. * 501 : 100kΩ Zonestar - Tronxy X3A
  483. * 502 : 100kΩ Zonestar - used by hot bed in Zonestar Průša P802M
  484. * 503 : 100kΩ Zonestar (Z8XM2) Heated Bed thermistor
  485. * 504 : 100kΩ Zonestar P802QR2 (Part# QWG-104F-B3950) Hotend Thermistor
  486. * 505 : 100kΩ Zonestar P802QR2 (Part# QWG-104F-3950) Bed Thermistor
  487. * 512 : 100kΩ RPW-Ultra hotend
  488. * 6 : 100kΩ EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
  489. * 7 : 100kΩ Honeywell 135-104LAG-J01
  490. * 71 : 100kΩ Honeywell 135-104LAF-J01
  491. * 8 : 100kΩ Vishay 0603 SMD NTCS0603E3104FXT
  492. * 9 : 100kΩ GE Sensing AL03006-58.2K-97-G1
  493. * 10 : 100kΩ RS PRO 198-961
  494. * 11 : 100kΩ Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
  495. * 12 : 100kΩ Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
  496. * 13 : 100kΩ Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
  497. * 15 : 100kΩ Calibrated for JGAurora A5 hotend
  498. * 18 : 200kΩ ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
  499. * 22 : 100kΩ GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
  500. * 23 : 100kΩ GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
  501. * 30 : 100kΩ Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
  502. * 60 : 100kΩ Maker's Tool Works Kapton Bed Thermistor - beta 3950
  503. * 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
  504. * 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
  505. * 67 : 500kΩ SliceEngineering 450°C Thermistor
  506. * 68 : PT100 amplifier board from Dyze Design
  507. * 70 : 100kΩ bq Hephestos 2
  508. * 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
  509. * 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
  510. *
  511. * Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
  512. * ------- (but gives greater accuracy and more stable PID)
  513. * 51 : 100kΩ EPCOS (1kΩ pullup)
  514. * 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
  515. * 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
  516. *
  517. * Analog Thermistors - 10kΩ pullup - Atypical
  518. * -------
  519. * 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
  520. *
  521. * Analog RTDs (Pt100/Pt1000)
  522. * -------
  523. * 110 : Pt100 with 1kΩ pullup (atypical)
  524. * 147 : Pt100 with 4.7kΩ pullup
  525. * 1010 : Pt1000 with 1kΩ pullup (atypical)
  526. * 1022 : Pt1000 with 2.2kΩ pullup
  527. * 1047 : Pt1000 with 4.7kΩ pullup (E3D)
  528. * 20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
  529. * NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
  530. * 21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
  531. * NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
  532. * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
  533. *
  534. * Custom/Dummy/Other Thermal Sensors
  535. * ------
  536. * 0 : not used
  537. * 1000 : Custom - Specify parameters in Configuration_adv.h
  538. *
  539. * !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  540. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  541. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  542. *
  543. */
  544. #define TEMP_SENSOR_0 5
  545. #define TEMP_SENSOR_1 0
  546. #define TEMP_SENSOR_2 0
  547. #define TEMP_SENSOR_3 0
  548. #define TEMP_SENSOR_4 0
  549. #define TEMP_SENSOR_5 0
  550. #define TEMP_SENSOR_6 0
  551. #define TEMP_SENSOR_7 0
  552. #define TEMP_SENSOR_BED 5
  553. #define TEMP_SENSOR_PROBE 0
  554. #define TEMP_SENSOR_CHAMBER 0
  555. #define TEMP_SENSOR_COOLER 0
  556. #define TEMP_SENSOR_BOARD 0
  557. #define TEMP_SENSOR_REDUNDANT 0
  558.  
  559. // Dummy thermistor constant temperature readings, for use with 998 and 999
  560. #define DUMMY_THERMISTOR_998_VALUE 25
  561. #define DUMMY_THERMISTOR_999_VALUE 100
  562.  
  563. // Resistor values when using MAX31865 sensors (-5) on TEMP_SENSOR_0 / 1
  564. #if TEMP_SENSOR_IS_MAX_TC(0)
  565. #define MAX31865_SENSOR_OHMS_0 100 // (Ω) Typically 100 or 1000 (PT100 or PT1000)
  566. #define MAX31865_CALIBRATION_OHMS_0 430 // (Ω) Typically 430 for Adafruit PT100; 4300 for Adafruit PT1000
  567. #endif
  568. #if TEMP_SENSOR_IS_MAX_TC(1)
  569. #define MAX31865_SENSOR_OHMS_1 100
  570. #define MAX31865_CALIBRATION_OHMS_1 430
  571. #endif
  572. #if TEMP_SENSOR_IS_MAX_TC(2)
  573. #define MAX31865_SENSOR_OHMS_2 100
  574. #define MAX31865_CALIBRATION_OHMS_2 430
  575. #endif
  576.  
  577. #if HAS_E_TEMP_SENSOR
  578. #define TEMP_RESIDENCY_TIME 6 // (seconds) Time to wait for hotend to "settle" in M109
  579. #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  580. #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  581. #endif
  582.  
  583. #if TEMP_SENSOR_BED
  584. #define TEMP_BED_RESIDENCY_TIME 6 // (seconds) Time to wait for bed to "settle" in M190
  585. #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  586. #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  587. #endif
  588.  
  589. #if TEMP_SENSOR_CHAMBER
  590. #define TEMP_CHAMBER_RESIDENCY_TIME 10 // (seconds) Time to wait for chamber to "settle" in M191
  591. #define TEMP_CHAMBER_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
  592. #define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
  593. #endif
  594.  
  595. /**
  596. * Redundant Temperature Sensor (TEMP_SENSOR_REDUNDANT)
  597. *
  598. * Use a temp sensor as a redundant sensor for another reading. Select an unused temperature sensor, and another
  599. * sensor you'd like it to be redundant for. If the two thermistors differ by TEMP_SENSOR_REDUNDANT_MAX_DIFF (°C),
  600. * the print will be aborted. Whichever sensor is selected will have its normal functions disabled; i.e. selecting
  601. * the Bed sensor (-1) will disable bed heating/monitoring.
  602. *
  603. * For selecting source/target use: COOLER, PROBE, BOARD, CHAMBER, BED, E0, E1, E2, E3, E4, E5, E6, E7
  604. */
  605. #if TEMP_SENSOR_REDUNDANT
  606. #define TEMP_SENSOR_REDUNDANT_SOURCE E1 // The sensor that will provide the redundant reading.
  607. #define TEMP_SENSOR_REDUNDANT_TARGET E0 // The sensor that we are providing a redundant reading for.
  608. #define TEMP_SENSOR_REDUNDANT_MAX_DIFF 10 // (°C) Temperature difference that will trigger a print abort.
  609. #endif
  610.  
  611. // Below this temperature the heater will be switched off
  612. // because it probably indicates a broken thermistor wire.
  613. #define HEATER_0_MINTEMP 5
  614. #define HEATER_1_MINTEMP 5
  615. #define HEATER_2_MINTEMP 5
  616. #define HEATER_3_MINTEMP 5
  617. #define HEATER_4_MINTEMP 5
  618. #define HEATER_5_MINTEMP 5
  619. #define HEATER_6_MINTEMP 5
  620. #define HEATER_7_MINTEMP 5
  621. #define BED_MINTEMP 5
  622. #define CHAMBER_MINTEMP 5
  623.  
  624. // Above this temperature the heater will be switched off.
  625. // This can protect components from overheating, but NOT from shorts and failures.
  626. // (Use MINTEMP for thermistor short/failure protection.)
  627. #define HEATER_0_MAXTEMP 275
  628. #define HEATER_1_MAXTEMP 275
  629. #define HEATER_2_MAXTEMP 275
  630. #define HEATER_3_MAXTEMP 275
  631. #define HEATER_4_MAXTEMP 275
  632. #define HEATER_5_MAXTEMP 275
  633. #define HEATER_6_MAXTEMP 275
  634. #define HEATER_7_MAXTEMP 275
  635. #define BED_MAXTEMP 130
  636. #define CHAMBER_MAXTEMP 60
  637.  
  638. /**
  639. * Thermal Overshoot
  640. * During heatup (and printing) the temperature can often "overshoot" the target by many degrees
  641. * (especially before PID tuning). Setting the target temperature too close to MAXTEMP guarantees
  642. * a MAXTEMP shutdown! Use these values to forbid temperatures being set too close to MAXTEMP.
  643. */
  644. #define HOTEND_OVERSHOOT 15 // (°C) Forbid temperatures over MAXTEMP - OVERSHOOT
  645. #define BED_OVERSHOOT 10 // (°C) Forbid temperatures over MAXTEMP - OVERSHOOT
  646. #define COOLER_OVERSHOOT 2 // (°C) Forbid temperatures closer than OVERSHOOT
  647.  
  648. //===========================================================================
  649. //============================= PID Settings ================================
  650. //===========================================================================
  651.  
  652. // @section hotend temp
  653.  
  654. // Enable PIDTEMP for PID control or MPCTEMP for Predictive Model.
  655. // temperature control. Disable both for bang-bang heating.
  656. #define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning
  657. //#define MPCTEMP // ** EXPERIMENTAL **
  658.  
  659. #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current
  660. #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  661. #define PID_K1 0.95 // Smoothing factor within any PID loop
  662.  
  663. #if ENABLED(PIDTEMP)
  664. //#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
  665. //#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
  666. // Set/get with G-code: M301 E[extruder number, 0-2]
  667.  
  668. // ANET A8 Standard Extruder at 210 Degree Celsius and 100% Fan
  669. // (measured after M106 S255 with M303 E0 S210 C8)
  670. #if ENABLED(PID_PARAMS_PER_HOTEND)
  671. // Specify up to one value per hotend here, according to your setup.
  672. // If there are fewer values, the last one applies to the remaining hotends.
  673. #define DEFAULT_Kp_LIST { 21.00, 20.00 }
  674. #define DEFAULT_Ki_LIST { 1.25, 1.25 }
  675. #define DEFAULT_Kd_LIST { 86.00, 86.00 }
  676. #else
  677. #define DEFAULT_Kp 37.08
  678. #define DEFAULT_Ki 4.97
  679. #define DEFAULT_Kd 69.22
  680. #endif
  681. #endif
  682.  
  683. /**
  684. * Model Predictive Control for hotend
  685. *
  686. * Use a physical model of the hotend to control temperature. When configured correctly
  687. * this gives better responsiveness and stability than PID and it also removes the need
  688. * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 T to autotune the model.
  689. * @section mpctemp
  690. */
  691. #if ENABLED(MPCTEMP)
  692. //#define MPC_EDIT_MENU // Add MPC editing to the "Advanced Settings" menu. (~1300 bytes of flash)
  693. //#define MPC_AUTOTUNE_MENU // Add MPC auto-tuning to the "Advanced Settings" menu. (~350 bytes of flash)
  694.  
  695. #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active.
  696. #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers.
  697.  
  698. #define MPC_INCLUDE_FAN // Model the fan speed?
  699.  
  700. // Measured physical constants from M306
  701. #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities.
  702. #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block.
  703. #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off.
  704. #if ENABLED(MPC_INCLUDE_FAN)
  705. #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full.
  706. #endif
  707.  
  708. // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect.
  709. #if ENABLED(MPC_INCLUDE_FAN)
  710. //#define MPC_FAN_0_ALL_HOTENDS
  711. //#define MPC_FAN_0_ACTIVE_HOTEND
  712. #endif
  713.  
  714. #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA).
  715. //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG).
  716.  
  717. // Advanced options
  718. #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization.
  719. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies.
  720. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced.
  721.  
  722. #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
  723. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position.
  724. #endif
  725.  
  726. //===========================================================================
  727. //====================== PID > Bed Temperature Control ======================
  728. //===========================================================================
  729.  
  730. /**
  731. * PID Bed Heating
  732. *
  733. * If this option is enabled set PID constants below.
  734. * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
  735. *
  736. * The PID frequency will be the same as the extruder PWM.
  737. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  738. * which is fine for driving a square wave into a resistive load and does not significantly
  739. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
  740. * heater. If your configuration is significantly different than this and you don't understand
  741. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  742. * @section bed temp
  743. */
  744. #define PIDTEMPBED
  745.  
  746. //#define BED_LIMIT_SWITCHING
  747.  
  748. /**
  749. * Max Bed Power
  750. * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
  751. * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
  752. * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
  753. */
  754. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  755.  
  756. #if ENABLED(PIDTEMPBED)
  757. //#define MIN_BED_POWER 0
  758. //#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
  759.  
  760. // ANET A8
  761. // original Bed + 0.3mm Heat conducting into 4mm borosilicate (PID-Autotune: M303 E-1 S60 C5):
  762. #define DEFAULT_bedKp 355.82
  763. #define DEFAULT_bedKi 70.18
  764. #define DEFAULT_bedKd 1202.66
  765.  
  766. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  767. #endif // PIDTEMPBED
  768.  
  769. //===========================================================================
  770. //==================== PID > Chamber Temperature Control ====================
  771. //===========================================================================
  772.  
  773. /**
  774. * PID Chamber Heating
  775. *
  776. * If this option is enabled set PID constants below.
  777. * If this option is disabled, bang-bang will be used and CHAMBER_LIMIT_SWITCHING will enable
  778. * hysteresis.
  779. *
  780. * The PID frequency will be the same as the extruder PWM.
  781. * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
  782. * which is fine for driving a square wave into a resistive load and does not significantly
  783. * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 200W
  784. * heater. If your configuration is significantly different than this and you don't understand
  785. * the issues involved, don't use chamber PID until someone else verifies that your hardware works.
  786. * @section chamber temp
  787. */
  788. //#define PIDTEMPCHAMBER
  789. //#define CHAMBER_LIMIT_SWITCHING
  790.  
  791. /**
  792. * Max Chamber Power
  793. * Applies to all forms of chamber control (PID, bang-bang, and bang-bang with hysteresis).
  794. * When set to any value below 255, enables a form of PWM to the chamber heater that acts like a divider
  795. * so don't use it unless you are OK with PWM on your heater. (See the comment on enabling PIDTEMPCHAMBER)
  796. */
  797. #define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
  798.  
  799. #if ENABLED(PIDTEMPCHAMBER)
  800. #define MIN_CHAMBER_POWER 0
  801. //#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
  802.  
  803. // Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
  804. // and placed inside the small Creality printer enclosure tent.
  805. //
  806. #define DEFAULT_chamberKp 37.04
  807. #define DEFAULT_chamberKi 1.40
  808. #define DEFAULT_chamberKd 655.17
  809. // M309 P37.04 I1.04 D655.17
  810.  
  811. // FIND YOUR OWN: "M303 E-2 C8 S50" to run autotune on the chamber at 50 degreesC for 8 cycles.
  812. #endif // PIDTEMPCHAMBER
  813.  
  814. #if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
  815. //#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  816. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  817. #define PID_FUNCTIONAL_RANGE 15 // If the temperature difference between the target temperature and the actual temperature
  818. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  819.  
  820. //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
  821. //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of flash)
  822. #endif
  823.  
  824. // @section safety
  825.  
  826. /**
  827. * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
  828. * Add M302 to set the minimum extrusion temperature and/or turn
  829. * cold extrusion prevention on and off.
  830. *
  831. * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  832. */
  833. #define PREVENT_COLD_EXTRUSION
  834. #define EXTRUDE_MINTEMP 160 // 160 guards against false tripping when the extruder fan kicks on.
  835.  
  836. /**
  837. * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
  838. * Note: For Bowden Extruders make this large enough to allow load/unload.
  839. */
  840. #define PREVENT_LENGTHY_EXTRUDE
  841. #define EXTRUDE_MAXLENGTH 200
  842.  
  843. //===========================================================================
  844. //======================== Thermal Runaway Protection =======================
  845. //===========================================================================
  846.  
  847. /**
  848. * Thermal Protection provides additional protection to your printer from damage
  849. * and fire. Marlin always includes safe min and max temperature ranges which
  850. * protect against a broken or disconnected thermistor wire.
  851. *
  852. * The issue: If a thermistor falls out, it will report the much lower
  853. * temperature of the air in the room, and the the firmware will keep
  854. * the heater on.
  855. *
  856. * If you get "Thermal Runaway" or "Heating failed" errors the
  857. * details can be tuned in Configuration_adv.h
  858. */
  859.  
  860. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  861. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  862. #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
  863. #define THERMAL_PROTECTION_COOLER // Enable thermal protection for the laser cooling
  864.  
  865. //===========================================================================
  866. //============================= Mechanical Settings =========================
  867. //===========================================================================
  868.  
  869. // @section machine
  870.  
  871. // Enable one of the options below for CoreXY, CoreXZ, or CoreYZ kinematics,
  872. // either in the usual order or reversed
  873. //#define COREXY
  874. //#define COREXZ
  875. //#define COREYZ
  876. //#define COREYX
  877. //#define COREZX
  878. //#define COREZY
  879. //#define MARKFORGED_XY // MarkForged. See https://reprap.org/forum/read.php?152,504042
  880. //#define MARKFORGED_YX
  881.  
  882. // Enable for a belt style printer with endless "Z" motion
  883. //#define BELTPRINTER
  884.  
  885. // Enable for Polargraph Kinematics
  886. //#define POLARGRAPH
  887. #if ENABLED(POLARGRAPH)
  888. #define POLARGRAPH_MAX_BELT_LEN 1035.0
  889. #define DEFAULT_SEGMENTS_PER_SECOND 5
  890. #endif
  891.  
  892. // @section delta
  893.  
  894. // Enable for DELTA kinematics and configure below
  895. //#define DELTA
  896. #if ENABLED(DELTA)
  897.  
  898. // Make delta curves from many straight lines (linear interpolation).
  899. // This is a trade-off between visible corners (not enough segments)
  900. // and processor overload (too many expensive sqrt calls).
  901. #define DEFAULT_SEGMENTS_PER_SECOND 200
  902.  
  903. // After homing move down to a height where XY movement is unconstrained
  904. //#define DELTA_HOME_TO_SAFE_ZONE
  905.  
  906. // Delta calibration menu
  907. // Add three-point calibration to the MarlinUI menu.
  908. // See http://minow.blogspot.com/index.html#4918805519571907051
  909. //#define DELTA_CALIBRATION_MENU
  910.  
  911. // G33 Delta Auto-Calibration. Enable EEPROM_SETTINGS to store results.
  912. //#define DELTA_AUTO_CALIBRATION
  913.  
  914. #if ENABLED(DELTA_AUTO_CALIBRATION)
  915. // Default number of probe points : n*n (1 -> 7)
  916. #define DELTA_CALIBRATION_DEFAULT_POINTS 4
  917. #endif
  918.  
  919. #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
  920. // Step size for paper-test probing
  921. #define PROBE_MANUALLY_STEP 0.05 // (mm)
  922. #endif
  923.  
  924. // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
  925. #define DELTA_PRINTABLE_RADIUS 140.0 // (mm)
  926.  
  927. // Maximum reachable area
  928. #define DELTA_MAX_RADIUS 140.0 // (mm)
  929.  
  930. // Center-to-center distance of the holes in the diagonal push rods.
  931. #define DELTA_DIAGONAL_ROD 250.0 // (mm)
  932.  
  933. // Distance between bed and nozzle Z home position
  934. #define DELTA_HEIGHT 250.00 // (mm) Get this value from G33 auto calibrate
  935.  
  936. #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
  937.  
  938. // Horizontal distance bridged by diagonal push rods when effector is centered.
  939. #define DELTA_RADIUS 124.0 // (mm) Get this value from G33 auto calibrate
  940.  
  941. // Trim adjustments for individual towers
  942. // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
  943. // measured in degrees anticlockwise looking from above the printer
  944. #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
  945.  
  946. // Delta radius and diagonal rod adjustments (mm)
  947. //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
  948. //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
  949. #endif
  950.  
  951. // @section scara
  952.  
  953. /**
  954. * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
  955. * Implemented and slightly reworked by JCERNY in June, 2014.
  956. *
  957. * Mostly Printed SCARA is an open source design by Tyler Williams. See:
  958. * https://www.thingiverse.com/thing:2487048
  959. * https://www.thingiverse.com/thing:1241491
  960. */
  961. //#define MORGAN_SCARA
  962. //#define MP_SCARA
  963. #if EITHER(MORGAN_SCARA, MP_SCARA)
  964. // If movement is choppy try lowering this value
  965. #define DEFAULT_SEGMENTS_PER_SECOND 200
  966.  
  967. // Length of inner and outer support arms. Measure arm lengths precisely.
  968. #define SCARA_LINKAGE_1 150 // (mm)
  969. #define SCARA_LINKAGE_2 150 // (mm)
  970.  
  971. // SCARA tower offset (position of Tower relative to bed zero position)
  972. // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
  973. #define SCARA_OFFSET_X 100 // (mm)
  974. #define SCARA_OFFSET_Y -56 // (mm)
  975.  
  976. #if ENABLED(MORGAN_SCARA)
  977.  
  978. //#define DEBUG_SCARA_KINEMATICS
  979. #define SCARA_FEEDRATE_SCALING // Convert XY feedrate from mm/s to degrees/s on the fly
  980.  
  981. // Radius around the center where the arm cannot reach
  982. #define MIDDLE_DEAD_ZONE_R 0 // (mm)
  983.  
  984. #define THETA_HOMING_OFFSET 0 // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
  985. #define PSI_HOMING_OFFSET 0 // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
  986.  
  987. #elif ENABLED(MP_SCARA)
  988.  
  989. #define SCARA_OFFSET_THETA1 12 // degrees
  990. #define SCARA_OFFSET_THETA2 131 // degrees
  991.  
  992. #endif
  993.  
  994. #endif
  995.  
  996. // @section tpara
  997.  
  998. // Enable for TPARA kinematics and configure below
  999. //#define AXEL_TPARA
  1000. #if ENABLED(AXEL_TPARA)
  1001. #define DEBUG_TPARA_KINEMATICS
  1002. #define DEFAULT_SEGMENTS_PER_SECOND 200
  1003.  
  1004. // Length of inner and outer support arms. Measure arm lengths precisely.
  1005. #define TPARA_LINKAGE_1 120 // (mm)
  1006. #define TPARA_LINKAGE_2 120 // (mm)
  1007.  
  1008. // SCARA tower offset (position of Tower relative to bed zero position)
  1009. // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
  1010. #define TPARA_OFFSET_X 0 // (mm)
  1011. #define TPARA_OFFSET_Y 0 // (mm)
  1012. #define TPARA_OFFSET_Z 0 // (mm)
  1013.  
  1014. #define SCARA_FEEDRATE_SCALING // Convert XY feedrate from mm/s to degrees/s on the fly
  1015.  
  1016. // Radius around the center where the arm cannot reach
  1017. #define MIDDLE_DEAD_ZONE_R 0 // (mm)
  1018.  
  1019. // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
  1020. #define THETA_HOMING_OFFSET 0
  1021. #define PSI_HOMING_OFFSET 0
  1022. #endif
  1023.  
  1024. // @section machine
  1025.  
  1026. // Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
  1027. //#define ARTICULATED_ROBOT_ARM
  1028.  
  1029. // For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
  1030. // ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
  1031. //#define FOAMCUTTER_XYUV
  1032.  
  1033. //===========================================================================
  1034. //============================== Endstop Settings ===========================
  1035. //===========================================================================
  1036.  
  1037. // @section endstops
  1038.  
  1039. // Specify here all the endstop connectors that are connected to any endstop or probe.
  1040. // Almost all printers will be using one per axis. Probes will use one or more of the
  1041. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  1042. #define USE_XMIN_PLUG
  1043. #define USE_YMIN_PLUG
  1044. #define USE_ZMIN_PLUG
  1045. //#define USE_IMIN_PLUG
  1046. //#define USE_JMIN_PLUG
  1047. //#define USE_KMIN_PLUG
  1048. //#define USE_UMIN_PLUG
  1049. //#define USE_VMIN_PLUG
  1050. //#define USE_WMIN_PLUG
  1051. //#define USE_XMAX_PLUG
  1052. //#define USE_YMAX_PLUG
  1053. //#define USE_ZMAX_PLUG
  1054. //#define USE_IMAX_PLUG
  1055. //#define USE_JMAX_PLUG
  1056. //#define USE_KMAX_PLUG
  1057. //#define USE_UMAX_PLUG
  1058. //#define USE_VMAX_PLUG
  1059. //#define USE_WMAX_PLUG
  1060.  
  1061. // Enable pullup for all endstops to prevent a floating state
  1062. #define ENDSTOPPULLUPS
  1063. #if DISABLED(ENDSTOPPULLUPS)
  1064. // Disable ENDSTOPPULLUPS to set pullups individually
  1065. //#define ENDSTOPPULLUP_XMIN
  1066. //#define ENDSTOPPULLUP_YMIN
  1067. //#define ENDSTOPPULLUP_ZMIN
  1068. //#define ENDSTOPPULLUP_IMIN
  1069. //#define ENDSTOPPULLUP_JMIN
  1070. //#define ENDSTOPPULLUP_KMIN
  1071. //#define ENDSTOPPULLUP_UMIN
  1072. //#define ENDSTOPPULLUP_VMIN
  1073. //#define ENDSTOPPULLUP_WMIN
  1074. //#define ENDSTOPPULLUP_XMAX
  1075. //#define ENDSTOPPULLUP_YMAX
  1076. //#define ENDSTOPPULLUP_ZMAX
  1077. //#define ENDSTOPPULLUP_IMAX
  1078. //#define ENDSTOPPULLUP_JMAX
  1079. //#define ENDSTOPPULLUP_KMAX
  1080. //#define ENDSTOPPULLUP_UMAX
  1081. //#define ENDSTOPPULLUP_VMAX
  1082. //#define ENDSTOPPULLUP_WMAX
  1083. //#define ENDSTOPPULLUP_ZMIN_PROBE
  1084. #endif
  1085.  
  1086. // Enable pulldown for all endstops to prevent a floating state
  1087. //#define ENDSTOPPULLDOWNS
  1088. #if DISABLED(ENDSTOPPULLDOWNS)
  1089. // Disable ENDSTOPPULLDOWNS to set pulldowns individually
  1090. //#define ENDSTOPPULLDOWN_XMIN
  1091. //#define ENDSTOPPULLDOWN_YMIN
  1092. //#define ENDSTOPPULLDOWN_ZMIN
  1093. //#define ENDSTOPPULLDOWN_IMIN
  1094. //#define ENDSTOPPULLDOWN_JMIN
  1095. //#define ENDSTOPPULLDOWN_KMIN
  1096. //#define ENDSTOPPULLDOWN_UMIN
  1097. //#define ENDSTOPPULLDOWN_VMIN
  1098. //#define ENDSTOPPULLDOWN_WMIN
  1099. //#define ENDSTOPPULLDOWN_XMAX
  1100. //#define ENDSTOPPULLDOWN_YMAX
  1101. //#define ENDSTOPPULLDOWN_ZMAX
  1102. //#define ENDSTOPPULLDOWN_IMAX
  1103. //#define ENDSTOPPULLDOWN_JMAX
  1104. //#define ENDSTOPPULLDOWN_KMAX
  1105. //#define ENDSTOPPULLDOWN_UMAX
  1106. //#define ENDSTOPPULLDOWN_VMAX
  1107. //#define ENDSTOPPULLDOWN_WMAX
  1108. //#define ENDSTOPPULLDOWN_ZMIN_PROBE
  1109. #endif
  1110.  
  1111. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  1112. #define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  1113. #define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  1114. #define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
  1115. #define I_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  1116. #define J_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  1117. #define K_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  1118. #define U_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  1119. #define V_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  1120. #define W_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  1121. #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  1122. #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  1123. #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  1124. #define I_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  1125. #define J_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  1126. #define K_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  1127. #define U_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  1128. #define V_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  1129. #define W_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
  1130. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe. //EC bltouch requirement
  1131.  
  1132. // Enable this feature if all enabled endstop pins are interrupt-capable.
  1133. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  1134. //#define ENDSTOP_INTERRUPTS_FEATURE //EC not compatible with SKR1.4
  1135.  
  1136. /**
  1137. * Endstop Noise Threshold
  1138. *
  1139. * Enable if your probe or endstops falsely trigger due to noise.
  1140. *
  1141. * - Higher values may affect repeatability or accuracy of some bed probes.
  1142. * - To fix noise install a 100nF ceramic capacitor in parallel with the switch.
  1143. * - This feature is not required for common micro-switches mounted on PCBs
  1144. * based on the Makerbot design, which already have the 100nF capacitor.
  1145. *
  1146. * :[2,3,4,5,6,7]
  1147. */
  1148. #define ENDSTOP_NOISE_THRESHOLD 2
  1149.  
  1150. // Check for stuck or disconnected endstops during homing moves.
  1151. //#define DETECT_BROKEN_ENDSTOP
  1152.  
  1153. //=============================================================================
  1154. //============================== Movement Settings ============================
  1155. //=============================================================================
  1156. // @section motion
  1157.  
  1158. /**
  1159. * Default Settings
  1160. *
  1161. * These settings can be reset by M502
  1162. *
  1163. * Note that if EEPROM is enabled, saved values will override these.
  1164. */
  1165.  
  1166. /**
  1167. * With this option each E stepper can have its own factors for the
  1168. * following movement settings. If fewer factors are given than the
  1169. * total number of extruders, the last value applies to the rest.
  1170. */
  1171. //#define DISTINCT_E_FACTORS
  1172.  
  1173. /**
  1174. * Default Axis Steps Per Unit (linear=steps/mm, rotational=steps/°)
  1175. * Override with M92
  1176. * X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
  1177. */
  1178. #define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 400, 136 }
  1179.  
  1180. /**
  1181. * Default Max Feed Rate (linear=mm/s, rotational=°/s)
  1182. * Override with M203
  1183. * X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
  1184. */
  1185. #define DEFAULT_MAX_FEEDRATE { 400, 400, 8, 50 }
  1186.  
  1187. //#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
  1188. #if ENABLED(LIMITED_MAX_FR_EDITING)
  1189. #define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
  1190. #endif
  1191.  
  1192. /**
  1193. * Default Max Acceleration (speed change with time) (linear=mm/(s^2), rotational=°/(s^2))
  1194. * (Maximum start speed for accelerated moves)
  1195. * Override with M201
  1196. * X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
  1197. */
  1198. #define DEFAULT_MAX_ACCELERATION { 2000, 2000, 500, 10000 }
  1199.  
  1200. //#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
  1201. #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
  1202. #define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
  1203. #endif
  1204.  
  1205. /**
  1206. * Default Acceleration (speed change with time) (linear=mm/(s^2), rotational=°/(s^2))
  1207. * Override with M204
  1208. *
  1209. * M204 P Acceleration
  1210. * M204 R Retract Acceleration
  1211. * M204 T Travel Acceleration
  1212. */
  1213. #define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves EC default was 400, pulling acceleration from TH3D SKRmini reccomended settings
  1214. #define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration for retracts
  1215. #define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves
  1216.  
  1217. /**
  1218. * Default Jerk limits (mm/s)
  1219. * Override with M205 X Y Z . . . E
  1220. *
  1221. * "Jerk" specifies the minimum speed change that requires acceleration.
  1222. * When changing speed and direction, if the difference is less than the
  1223. * value set here, it may happen instantaneously.
  1224. */
  1225. //#define CLASSIC_JERK
  1226. #if ENABLED(CLASSIC_JERK)
  1227. #define DEFAULT_XJERK 10.0
  1228. #define DEFAULT_YJERK 10.0
  1229. #define DEFAULT_ZJERK 0.3
  1230. //#define DEFAULT_IJERK 0.3
  1231. //#define DEFAULT_JJERK 0.3
  1232. //#define DEFAULT_KJERK 0.3
  1233. //#define DEFAULT_UJERK 0.3
  1234. //#define DEFAULT_VJERK 0.3
  1235. //#define DEFAULT_WJERK 0.3
  1236.  
  1237. //#define TRAVEL_EXTRA_XYJERK 0.0 // Additional jerk allowance for all travel moves
  1238.  
  1239. //#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
  1240. #if ENABLED(LIMITED_JERK_EDITING)
  1241. #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
  1242. #endif
  1243. #endif
  1244.  
  1245. #define DEFAULT_EJERK 5.0 // May be used by Linear Advance
  1246.  
  1247. /**
  1248. * Junction Deviation Factor
  1249. *
  1250. * See:
  1251. * https://reprap.org/forum/read.php?1,739819
  1252. * https://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
  1253. */
  1254. #if DISABLED(CLASSIC_JERK)
  1255. #define JUNCTION_DEVIATION_MM 0.10 // (mm) Distance from real junction edge
  1256. #define JD_HANDLE_SMALL_SEGMENTS // Use curvature estimation instead of just the junction angle
  1257. // for small segments (< 1mm) with large junction angles (> 135°).
  1258. #endif
  1259.  
  1260. /**
  1261. * S-Curve Acceleration
  1262. *
  1263. * This option eliminates vibration during printing by fitting a Bézier
  1264. * curve to move acceleration, producing much smoother direction changes.
  1265. *
  1266. * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  1267. */
  1268. //#define S_CURVE_ACCELERATION
  1269.  
  1270. //===========================================================================
  1271. //============================= Z Probe Options =============================
  1272. //===========================================================================
  1273. // @section probes
  1274.  
  1275. //
  1276. // See https://marlinfw.org/docs/configuration/probes.html
  1277. //
  1278.  
  1279. /**
  1280. * Enable this option for a probe connected to the Z-MIN pin.
  1281. * The probe replaces the Z-MIN endstop and is used for Z homing.
  1282. * (Automatically enables USE_PROBE_FOR_Z_HOMING.)
  1283. */
  1284. //#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN //EC using the probe pin
  1285.  
  1286. // Force the use of the probe for Z-axis homing
  1287. #define USE_PROBE_FOR_Z_HOMING //EC
  1288.  
  1289. /**
  1290. * Z_MIN_PROBE_PIN
  1291. *
  1292. * Define this pin if the probe is not connected to Z_MIN_PIN.
  1293. * If not defined the default pin for the selected MOTHERBOARD
  1294. * will be used. Most of the time the default is what you want.
  1295. *
  1296. * - The simplest option is to use a free endstop connector.
  1297. * - Use 5V for powered (usually inductive) sensors.
  1298. *
  1299. * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  1300. * - For simple switches connect...
  1301. * - normally-closed switches to GND and D32.
  1302. * - normally-open switches to 5V and D32.
  1303. */
  1304. //#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
  1305.  
  1306. /**
  1307. * Probe Type
  1308. *
  1309. * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  1310. * Activate one of these to use Auto Bed Leveling below.
  1311. */
  1312.  
  1313. /**
  1314. * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  1315. * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  1316. * or (with LCD_BED_LEVELING) the LCD controller.
  1317. */
  1318. //#define PROBE_MANUALLY
  1319.  
  1320. /**
  1321. * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  1322. * (e.g., an inductive probe or a nozzle-based probe-switch.)
  1323. */
  1324. //#define FIX_MOUNTED_PROBE
  1325.  
  1326. /**
  1327. * Use the nozzle as the probe, as with a conductive
  1328. * nozzle system or a piezo-electric smart effector.
  1329. */
  1330. //#define NOZZLE_AS_PROBE
  1331.  
  1332. /**
  1333. * Z Servo Probe, such as an endstop switch on a rotating arm.
  1334. */
  1335. //#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.
  1336. //#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles
  1337.  
  1338. /**
  1339. * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  1340. */
  1341. #define BLTOUCH //EC
  1342.  
  1343. /**
  1344. * MagLev V4 probe by MDD
  1345. *
  1346. * This probe is deployed and activated by powering a built-in electromagnet.
  1347. */
  1348. //#define MAGLEV4
  1349. #if ENABLED(MAGLEV4)
  1350. //#define MAGLEV_TRIGGER_PIN 11 // Set to the connected digital output
  1351. #define MAGLEV_TRIGGER_DELAY 15 // Changing this risks overheating the coil
  1352. #endif
  1353.  
  1354. /**
  1355. * Touch-MI Probe by hotends.fr
  1356. *
  1357. * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed.
  1358. * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is
  1359. * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  1360. *
  1361. * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
  1362. * and a minimum Z_HOMING_HEIGHT of 10.
  1363. */
  1364. //#define TOUCH_MI_PROBE
  1365. #if ENABLED(TOUCH_MI_PROBE)
  1366. #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts
  1367. //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed
  1368. //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu)
  1369. #endif
  1370.  
  1371. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  1372. //#define SOLENOID_PROBE
  1373.  
  1374. // A sled-mounted probe like those designed by Charles Bell.
  1375. //#define Z_PROBE_SLED
  1376. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  1377.  
  1378. // A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice.
  1379. //#define RACK_AND_PINION_PROBE
  1380. #if ENABLED(RACK_AND_PINION_PROBE)
  1381. #define Z_PROBE_DEPLOY_X X_MIN_POS
  1382. #define Z_PROBE_RETRACT_X X_MAX_POS
  1383. #endif
  1384.  
  1385. /**
  1386. * Magnetically Mounted Probe
  1387. * For probes such as Euclid, Klicky, Klackender, etc.
  1388. */
  1389. //#define MAG_MOUNTED_PROBE
  1390. #if ENABLED(MAG_MOUNTED_PROBE)
  1391. #define PROBE_DEPLOY_FEEDRATE (133*60) // (mm/min) Probe deploy speed
  1392. #define PROBE_STOW_FEEDRATE (133*60) // (mm/min) Probe stow speed
  1393.  
  1394. #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } } // Move to side Dock & Attach probe
  1395. #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } } // Move probe off dock
  1396. #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, { 0, 0, 0 } } // Extra move if needed
  1397. #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, { 0, 0, 0 } } // Extra move if needed
  1398. #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, { 0, 0, 0 } } // Extra move if needed
  1399. #define MAG_MOUNTED_STOW_1 { PROBE_STOW_FEEDRATE, { 245, 114, 20 } } // Move to dock
  1400. #define MAG_MOUNTED_STOW_2 { PROBE_STOW_FEEDRATE, { 245, 114, 0 } } // Place probe beside remover
  1401. #define MAG_MOUNTED_STOW_3 { PROBE_STOW_FEEDRATE, { 230, 114, 0 } } // Side move to remove probe
  1402. #define MAG_MOUNTED_STOW_4 { PROBE_STOW_FEEDRATE, { 210, 114, 20 } } // Side move to remove probe
  1403. #define MAG_MOUNTED_STOW_5 { PROBE_STOW_FEEDRATE, { 0, 0, 0 } } // Extra move if needed
  1404. #endif
  1405.  
  1406. // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
  1407. // When the pin is defined you can use M672 to set/reset the probe sensitivity.
  1408. //#define DUET_SMART_EFFECTOR
  1409. #if ENABLED(DUET_SMART_EFFECTOR)
  1410. #define SMART_EFFECTOR_MOD_PIN -1 // Connect a GPIO pin to the Smart Effector MOD pin
  1411. #endif
  1412.  
  1413. /**
  1414. * Use StallGuard2 to probe the bed with the nozzle.
  1415. * Requires stallGuard-capable Trinamic stepper drivers.
  1416. * CAUTION: This can damage machines with Z lead screws.
  1417. * Take extreme care when setting up this feature.
  1418. */
  1419. //#define SENSORLESS_PROBING
  1420.  
  1421. /**
  1422. * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
  1423. * Deploys by touching z-axis belt. Retracts by pushing the probe down.
  1424. */
  1425. //#define Z_PROBE_ALLEN_KEY
  1426. #if ENABLED(Z_PROBE_ALLEN_KEY)
  1427. // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
  1428. // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
  1429.  
  1430. #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
  1431. #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
  1432.  
  1433. #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
  1434. #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
  1435.  
  1436. #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
  1437. #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
  1438.  
  1439. #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
  1440. #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
  1441.  
  1442. #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
  1443. #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
  1444.  
  1445. #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
  1446. #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
  1447.  
  1448. #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
  1449. #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
  1450.  
  1451. #endif // Z_PROBE_ALLEN_KEY
  1452.  
  1453. /**
  1454. * Nozzle-to-Probe offsets { X, Y, Z }
  1455. *
  1456. * X and Y offset
  1457. * Use a caliper or ruler to measure the distance from the tip of
  1458. * the Nozzle to the center-point of the Probe in the X and Y axes.
  1459. *
  1460. * Z offset
  1461. * - For the Z offset use your best known value and adjust at runtime.
  1462. * - Common probes trigger below the nozzle and have negative values for Z offset.
  1463. * - Probes triggering above the nozzle height are uncommon but do exist. When using
  1464. * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES
  1465. * to avoid collisions during probing.
  1466. *
  1467. * Tune and Adjust
  1468. * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc.
  1469. * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset.
  1470. *
  1471. * Assuming the typical work area orientation:
  1472. * - Probe to RIGHT of the Nozzle has a Positive X offset
  1473. * - Probe to LEFT of the Nozzle has a Negative X offset
  1474. * - Probe in BACK of the Nozzle has a Positive Y offset
  1475. * - Probe in FRONT of the Nozzle has a Negative Y offset
  1476. *
  1477. * Some examples:
  1478. * #define NOZZLE_TO_PROBE_OFFSET { 10, 10, -1 } // Example "1"
  1479. * #define NOZZLE_TO_PROBE_OFFSET {-10, 5, -1 } // Example "2"
  1480. * #define NOZZLE_TO_PROBE_OFFSET { 5, -5, -1 } // Example "3"
  1481. * #define NOZZLE_TO_PROBE_OFFSET {-15,-10, -1 } // Example "4"
  1482. *
  1483. * +-- BACK ---+
  1484. * | [+] |
  1485. * L | 1 | R <-- Example "1" (right+, back+)
  1486. * E | 2 | I <-- Example "2" ( left-, back+)
  1487. * F |[-] N [+]| G <-- Nozzle
  1488. * T | 3 | H <-- Example "3" (right+, front-)
  1489. * | 4 | T <-- Example "4" ( left-, front-)
  1490. * | [-] |
  1491. * O-- FRONT --+
  1492. */
  1493. #define NOZZLE_TO_PROBE_OFFSET { -30, -10.5, -1.75 } //ec https://www.thingiverse.com/thing:4725060
  1494.  
  1495. // Most probes should stay away from the edges of the bed, but
  1496. // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
  1497. #define PROBING_MARGIN 10
  1498.  
  1499. // X and Y axis travel speed (mm/min) between probes
  1500. #define XY_PROBE_FEEDRATE (100*60)
  1501.  
  1502. // Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2)
  1503. #define Z_PROBE_FEEDRATE_FAST (4*60)
  1504.  
  1505. // Feedrate (mm/min) for the "accurate" probe of each point
  1506. #define Z_PROBE_FEEDRATE_SLOW (Z_PROBE_FEEDRATE_FAST / 2)
  1507.  
  1508. /**
  1509. * Probe Activation Switch
  1510. * A switch indicating proper deployment, or an optical
  1511. * switch triggered when the carriage is near the bed.
  1512. */
  1513. //#define PROBE_ACTIVATION_SWITCH
  1514. #if ENABLED(PROBE_ACTIVATION_SWITCH)
  1515. #define PROBE_ACTIVATION_SWITCH_STATE LOW // State indicating probe is active
  1516. //#define PROBE_ACTIVATION_SWITCH_PIN PC6 // Override default pin
  1517. #endif
  1518.  
  1519. /**
  1520. * Tare Probe (determine zero-point) prior to each probe.
  1521. * Useful for a strain gauge or piezo sensor that needs to factor out
  1522. * elements such as cables pulling on the carriage.
  1523. */
  1524. //#define PROBE_TARE
  1525. #if ENABLED(PROBE_TARE)
  1526. #define PROBE_TARE_TIME 200 // (ms) Time to hold tare pin
  1527. #define PROBE_TARE_DELAY 200 // (ms) Delay after tare before
  1528. #define PROBE_TARE_STATE HIGH // State to write pin for tare
  1529. //#define PROBE_TARE_PIN PA5 // Override default pin
  1530. #if ENABLED(PROBE_ACTIVATION_SWITCH)
  1531. //#define PROBE_TARE_ONLY_WHILE_INACTIVE // Fail to tare/probe if PROBE_ACTIVATION_SWITCH is active
  1532. #endif
  1533. #endif
  1534.  
  1535. /**
  1536. * Probe Enable / Disable
  1537. * The probe only provides a triggered signal when enabled.
  1538. */
  1539. //#define PROBE_ENABLE_DISABLE
  1540. #if ENABLED(PROBE_ENABLE_DISABLE)
  1541. //#define PROBE_ENABLE_PIN -1 // Override the default pin here
  1542. #endif
  1543.  
  1544. /**
  1545. * Multiple Probing
  1546. *
  1547. * You may get improved results by probing 2 or more times.
  1548. * With EXTRA_PROBING the more atypical reading(s) will be disregarded.
  1549. *
  1550. * A total of 2 does fast/slow probes with a weighted average.
  1551. * A total of 3 or more adds more slow probes, taking the average.
  1552. */
  1553. //#define MULTIPLE_PROBING 2
  1554. //#define EXTRA_PROBING 1
  1555.  
  1556. /**
  1557. * Z probes require clearance when deploying, stowing, and moving between
  1558. * probe points to avoid hitting the bed and other hardware.
  1559. * Servo-mounted probes require extra space for the arm to rotate.
  1560. * Inductive probes need space to keep from triggering early.
  1561. *
  1562. * Use these settings to specify the distance (mm) to raise the probe (or
  1563. * lower the bed). The values set here apply over and above any (negative)
  1564. * probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
  1565. * Only integer values >= 1 are valid here.
  1566. *
  1567. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  1568. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  1569. */
  1570. #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
  1571. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  1572. #define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
  1573. //#define Z_AFTER_PROBING 5 // Z position after probing is done
  1574.  
  1575. #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
  1576.  
  1577. // For M851 give a range for adjusting the Z probe offset
  1578. #define Z_PROBE_OFFSET_RANGE_MIN -20
  1579. #define Z_PROBE_OFFSET_RANGE_MAX 20
  1580.  
  1581. // Enable the M48 repeatability test to test probe accuracy
  1582. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  1583.  
  1584. // Before deploy/stow pause for user confirmation
  1585. //#define PAUSE_BEFORE_DEPLOY_STOW
  1586. #if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
  1587. //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
  1588. #endif
  1589.  
  1590. /**
  1591. * Enable one or more of the following if probing seems unreliable.
  1592. * Heaters and/or fans can be disabled during probing to minimize electrical
  1593. * noise. A delay can also be added to allow noise and vibration to settle.
  1594. * These options are most useful for the BLTouch probe, but may also improve
  1595. * readings with inductive probes and piezo sensors.
  1596. */
  1597. //#define PROBING_HEATERS_OFF // Turn heaters off when probing
  1598. #if ENABLED(PROBING_HEATERS_OFF)
  1599. //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
  1600. //#define WAIT_FOR_HOTEND // Wait for hotend to heat back up between probes (to improve accuracy & prevent cold extrude)
  1601. #endif
  1602. //#define PROBING_FANS_OFF // Turn fans off when probing
  1603. //#define PROBING_ESTEPPERS_OFF // Turn all extruder steppers off when probing
  1604. //#define PROBING_STEPPERS_OFF // Turn all steppers off (unless needed to hold position) when probing (including extruders)
  1605. //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
  1606.  
  1607. // Require minimum nozzle and/or bed temperature for probing
  1608. //#define PREHEAT_BEFORE_PROBING
  1609. #if ENABLED(PREHEAT_BEFORE_PROBING)
  1610. #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time
  1611. #define PROBING_BED_TEMP 50
  1612. #endif
  1613.  
  1614. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  1615. // :{ 0:'Low', 1:'High' }
  1616. #define X_ENABLE_ON 0
  1617. #define Y_ENABLE_ON 0
  1618. #define Z_ENABLE_ON 0
  1619. #define E_ENABLE_ON 0 // For all extruders
  1620. //#define I_ENABLE_ON 0
  1621. //#define J_ENABLE_ON 0
  1622. //#define K_ENABLE_ON 0
  1623. //#define U_ENABLE_ON 0
  1624. //#define V_ENABLE_ON 0
  1625. //#define W_ENABLE_ON 0
  1626.  
  1627. // Disable axis steppers immediately when they're not being stepped.
  1628. // WARNING: When motors turn off there is a chance of losing position accuracy!
  1629. #define DISABLE_X false
  1630. #define DISABLE_Y false
  1631. #define DISABLE_Z false
  1632. //#define DISABLE_I false
  1633. //#define DISABLE_J false
  1634. //#define DISABLE_K false
  1635. //#define DISABLE_U false
  1636. //#define DISABLE_V false
  1637. //#define DISABLE_W false
  1638.  
  1639. // Turn off the display blinking that warns about possible accuracy reduction
  1640. //#define DISABLE_REDUCED_ACCURACY_WARNING
  1641.  
  1642. // @section extruder
  1643.  
  1644. #define DISABLE_E false // Disable the extruder when not stepping
  1645. #define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled
  1646.  
  1647. // @section motion
  1648.  
  1649. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  1650. #define INVERT_X_DIR true //EC all motors need to be inverted except for Z with default anet motors
  1651. #define INVERT_Y_DIR true
  1652. #define INVERT_Z_DIR false
  1653. //#define INVERT_I_DIR false
  1654. //#define INVERT_J_DIR false
  1655. //#define INVERT_K_DIR false
  1656. //#define INVERT_U_DIR false
  1657. //#define INVERT_V_DIR false
  1658. //#define INVERT_W_DIR false
  1659.  
  1660. // @section extruder
  1661.  
  1662. // For direct drive extruder v9 set to true, for geared extruder set to false.
  1663. #define INVERT_E0_DIR true
  1664. #define INVERT_E1_DIR false
  1665. #define INVERT_E2_DIR false
  1666. #define INVERT_E3_DIR false
  1667. #define INVERT_E4_DIR false
  1668. #define INVERT_E5_DIR false
  1669. #define INVERT_E6_DIR false
  1670. #define INVERT_E7_DIR false
  1671.  
  1672. // @section homing
  1673.  
  1674. //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed. Also enable HOME_AFTER_DEACTIVATE for extra safety.
  1675. //#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated. Also enable NO_MOTION_BEFORE_HOMING for extra safety.
  1676.  
  1677. /**
  1678. * Set Z_IDLE_HEIGHT if the Z-Axis moves on its own when steppers are disabled.
  1679. * - Use a low value (i.e., Z_MIN_POS) if the nozzle falls down to the bed.
  1680. * - Use a large value (i.e., Z_MAX_POS) if the bed falls down, away from the nozzle.
  1681. */
  1682. //#define Z_IDLE_HEIGHT Z_HOME_POS
  1683.  
  1684. //#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
  1685. // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
  1686.  
  1687. //#define Z_AFTER_HOMING 10 // (mm) Height to move to after homing Z
  1688.  
  1689. // Direction of endstops when homing; 1=MAX, -1=MIN
  1690. // :[-1,1]
  1691. #define X_HOME_DIR -1
  1692. #define Y_HOME_DIR -1
  1693. #define Z_HOME_DIR -1
  1694. //#define I_HOME_DIR -1
  1695. //#define J_HOME_DIR -1
  1696. //#define K_HOME_DIR -1
  1697. //#define U_HOME_DIR -1
  1698. //#define V_HOME_DIR -1
  1699. //#define W_HOME_DIR -1
  1700.  
  1701. // @section geometry
  1702.  
  1703. // The size of the printable area
  1704. #define X_BED_SIZE 255 //EC This is the size of the ender 3 bed we're using, actual printable area is smaller
  1705. #define Y_BED_SIZE 230 //bed sits forward 10mm and unless you feel like moving the gantry... again... it's gonna stay that way.
  1706.  
  1707. // Travel limits (linear=mm, rotational=°) after homing, corresponding to endstop positions.
  1708. #define X_MIN_POS -0 //EC default was -33
  1709. #define Y_MIN_POS 0 //EC default was -10
  1710. #define Z_MIN_POS 0
  1711. #define X_MAX_POS X_BED_SIZE
  1712. #define Y_MAX_POS Y_BED_SIZE
  1713. #define Z_MAX_POS 240
  1714. //#define I_MIN_POS 0
  1715. //#define I_MAX_POS 50
  1716. //#define J_MIN_POS 0
  1717. //#define J_MAX_POS 50
  1718. //#define K_MIN_POS 0
  1719. //#define K_MAX_POS 50
  1720. //#define U_MIN_POS 0
  1721. //#define U_MAX_POS 50
  1722. //#define V_MIN_POS 0
  1723. //#define V_MAX_POS 50
  1724. //#define W_MIN_POS 0
  1725. //#define W_MAX_POS 50
  1726.  
  1727. /**
  1728. * Software Endstops
  1729. *
  1730. * - Prevent moves outside the set machine bounds.
  1731. * - Individual axes can be disabled, if desired.
  1732. * - X and Y only apply to Cartesian robots.
  1733. * - Use 'M211' to set software endstops on/off or report current state
  1734. */
  1735.  
  1736. // Min software endstops constrain movement within minimum coordinate bounds
  1737. #define MIN_SOFTWARE_ENDSTOPS
  1738. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  1739. #define MIN_SOFTWARE_ENDSTOP_X
  1740. #define MIN_SOFTWARE_ENDSTOP_Y
  1741. #define MIN_SOFTWARE_ENDSTOP_Z
  1742. #define MIN_SOFTWARE_ENDSTOP_I
  1743. #define MIN_SOFTWARE_ENDSTOP_J
  1744. #define MIN_SOFTWARE_ENDSTOP_K
  1745. #define MIN_SOFTWARE_ENDSTOP_U
  1746. #define MIN_SOFTWARE_ENDSTOP_V
  1747. #define MIN_SOFTWARE_ENDSTOP_W
  1748. #endif
  1749.  
  1750. // Max software endstops constrain movement within maximum coordinate bounds
  1751. #define MAX_SOFTWARE_ENDSTOPS
  1752. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  1753. #define MAX_SOFTWARE_ENDSTOP_X
  1754. #define MAX_SOFTWARE_ENDSTOP_Y
  1755. #define MAX_SOFTWARE_ENDSTOP_Z
  1756. #define MAX_SOFTWARE_ENDSTOP_I
  1757. #define MAX_SOFTWARE_ENDSTOP_J
  1758. #define MAX_SOFTWARE_ENDSTOP_K
  1759. #define MAX_SOFTWARE_ENDSTOP_U
  1760. #define MAX_SOFTWARE_ENDSTOP_V
  1761. #define MAX_SOFTWARE_ENDSTOP_W
  1762. #endif
  1763.  
  1764. #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
  1765. //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
  1766. #endif
  1767.  
  1768. /**
  1769. * Filament Runout Sensors
  1770. * Mechanical or opto endstops are used to check for the presence of filament.
  1771. *
  1772. * IMPORTANT: Runout will only trigger if Marlin is aware that a print job is running.
  1773. * Marlin knows a print job is running when:
  1774. * 1. Running a print job from media started with M24.
  1775. * 2. The Print Job Timer has been started with M75.
  1776. * 3. The heaters were turned on and PRINTJOB_TIMER_AUTOSTART is enabled.
  1777. *
  1778. * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  1779. * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  1780. */
  1781. //#define FILAMENT_RUNOUT_SENSOR
  1782. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  1783. #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
  1784. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
  1785.  
  1786. #define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present.
  1787. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
  1788. //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
  1789. //#define WATCH_ALL_RUNOUT_SENSORS // Execute runout script on any triggering sensor, not only for the active extruder.
  1790. // This is automatically enabled for MIXING_EXTRUDERs.
  1791.  
  1792. // Override individually if the runout sensors vary
  1793. //#define FIL_RUNOUT1_STATE LOW
  1794. //#define FIL_RUNOUT1_PULLUP
  1795. //#define FIL_RUNOUT1_PULLDOWN
  1796.  
  1797. //#define FIL_RUNOUT2_STATE LOW
  1798. //#define FIL_RUNOUT2_PULLUP
  1799. //#define FIL_RUNOUT2_PULLDOWN
  1800.  
  1801. //#define FIL_RUNOUT3_STATE LOW
  1802. //#define FIL_RUNOUT3_PULLUP
  1803. //#define FIL_RUNOUT3_PULLDOWN
  1804.  
  1805. //#define FIL_RUNOUT4_STATE LOW
  1806. //#define FIL_RUNOUT4_PULLUP
  1807. //#define FIL_RUNOUT4_PULLDOWN
  1808.  
  1809. //#define FIL_RUNOUT5_STATE LOW
  1810. //#define FIL_RUNOUT5_PULLUP
  1811. //#define FIL_RUNOUT5_PULLDOWN
  1812.  
  1813. //#define FIL_RUNOUT6_STATE LOW
  1814. //#define FIL_RUNOUT6_PULLUP
  1815. //#define FIL_RUNOUT6_PULLDOWN
  1816.  
  1817. //#define FIL_RUNOUT7_STATE LOW
  1818. //#define FIL_RUNOUT7_PULLUP
  1819. //#define FIL_RUNOUT7_PULLDOWN
  1820.  
  1821. //#define FIL_RUNOUT8_STATE LOW
  1822. //#define FIL_RUNOUT8_PULLUP
  1823. //#define FIL_RUNOUT8_PULLDOWN
  1824.  
  1825. // Commands to execute on filament runout.
  1826. // With multiple runout sensors use the %c placeholder for the current tool in commands (e.g., "M600 T%c")
  1827. // NOTE: After 'M412 H1' the host handles filament runout and this script does not apply.
  1828. #define FILAMENT_RUNOUT_SCRIPT "M600"
  1829.  
  1830. // After a runout is detected, continue printing this length of filament
  1831. // before executing the runout script. Useful for a sensor at the end of
  1832. // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
  1833. //#define FILAMENT_RUNOUT_DISTANCE_MM 25
  1834.  
  1835. #ifdef FILAMENT_RUNOUT_DISTANCE_MM
  1836. // Enable this option to use an encoder disc that toggles the runout pin
  1837. // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
  1838. // large enough to avoid false positives.)
  1839. //#define FILAMENT_MOTION_SENSOR
  1840. #endif
  1841. #endif
  1842.  
  1843. //===========================================================================
  1844. //=============================== Bed Leveling ==============================
  1845. //===========================================================================
  1846. // @section calibrate
  1847.  
  1848. /**
  1849. * Choose one of the options below to enable G29 Bed Leveling. The parameters
  1850. * and behavior of G29 will change depending on your selection.
  1851. *
  1852. * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  1853. *
  1854. * - AUTO_BED_LEVELING_3POINT
  1855. * Probe 3 arbitrary points on the bed (that aren't collinear)
  1856. * You specify the XY coordinates of all 3 points.
  1857. * The result is a single tilted plane. Best for a flat bed.
  1858. *
  1859. * - AUTO_BED_LEVELING_LINEAR
  1860. * Probe several points in a grid.
  1861. * You specify the rectangle and the density of sample points.
  1862. * The result is a single tilted plane. Best for a flat bed.
  1863. *
  1864. * - AUTO_BED_LEVELING_BILINEAR
  1865. * Probe several points in a grid.
  1866. * You specify the rectangle and the density of sample points.
  1867. * The result is a mesh, best for large or uneven beds.
  1868. *
  1869. * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  1870. * A comprehensive bed leveling system combining the features and benefits
  1871. * of other systems. UBL also includes integrated Mesh Generation, Mesh
  1872. * Validation and Mesh Editing systems.
  1873. *
  1874. * - MESH_BED_LEVELING
  1875. * Probe a grid manually
  1876. * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  1877. * For machines without a probe, Mesh Bed Leveling provides a method to perform
  1878. * leveling in steps so you can manually adjust the Z height at each grid-point.
  1879. * With an LCD controller the process is guided step-by-step.
  1880. */
  1881. //#define AUTO_BED_LEVELING_3POINT
  1882. //#define AUTO_BED_LEVELING_LINEAR
  1883. //#define AUTO_BED_LEVELING_BILINEAR
  1884. #define AUTO_BED_LEVELING_UBL
  1885. //#define MESH_BED_LEVELING
  1886.  
  1887. /**
  1888. * Normally G28 leaves leveling disabled on completion. Enable one of
  1889. * these options to restore the prior leveling state or to always enable
  1890. * leveling immediately after G28.
  1891. */
  1892. //#define RESTORE_LEVELING_AFTER_G28
  1893. //#define ENABLE_LEVELING_AFTER_G28
  1894.  
  1895. /**
  1896. * Auto-leveling needs preheating
  1897. */
  1898. //#define PREHEAT_BEFORE_LEVELING
  1899. #if ENABLED(PREHEAT_BEFORE_LEVELING)
  1900. #define LEVELING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time
  1901. #define LEVELING_BED_TEMP 50
  1902. #endif
  1903.  
  1904. /**
  1905. * Bed Distance Sensor
  1906. *
  1907. * Measures the distance from bed to nozzle with accuracy of 0.01mm.
  1908. * For information about this sensor https://github.com/markniu/Bed_Distance_sensor
  1909. * Uses I2C port, so it requires I2C library markyue/Panda_SoftMasterI2C.
  1910. */
  1911. //#define BD_SENSOR
  1912.  
  1913. /**
  1914. * Enable detailed logging of G28, G29, M48, etc.
  1915. * Turn on with the command 'M111 S32'.
  1916. * NOTE: Requires a lot of PROGMEM!
  1917. */
  1918. //#define DEBUG_LEVELING_FEATURE
  1919.  
  1920. #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL, PROBE_MANUALLY)
  1921. // Set a height for the start of manual adjustment
  1922. #define MANUAL_PROBE_START_Z 0.2 // (mm) Comment out to use the last-measured height
  1923. #endif
  1924.  
  1925. #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL)
  1926. /**
  1927. * Gradually reduce leveling correction until a set height is reached,
  1928. * at which point movement will be level to the machine's XY plane.
  1929. * The height can be set with M420 Z<height>
  1930. */
  1931. #define ENABLE_LEVELING_FADE_HEIGHT
  1932. #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
  1933. #define DEFAULT_LEVELING_FADE_HEIGHT 10.0 // (mm) Default fade height.
  1934. #endif
  1935.  
  1936. /**
  1937. * For Cartesian machines, instead of dividing moves on mesh boundaries,
  1938. * split up moves into short segments like a Delta. This follows the
  1939. * contours of the bed more closely than edge-to- edge straight moves.
  1940. */
  1941. #define SEGMENT_LEVELED_MOVES
  1942. #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  1943.  
  1944. /**
  1945. * Enable the G26 Mesh Validation Pattern tool.
  1946. */
  1947. #define G26_MESH_VALIDATION //EC
  1948. #if ENABLED(G26_MESH_VALIDATION)
  1949. #define MESH_TEST_NOZZLE_SIZE 0.6 // (mm) Diameter of primary nozzle. //ec changed to 0.6
  1950. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for G26.
  1951. #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for G26.
  1952. #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for G26.
  1953. #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for G26 XY moves.
  1954. #define G26_XY_FEEDRATE_TRAVEL 100 // (mm/s) Feedrate for G26 XY travel moves.
  1955. #define G26_RETRACT_MULTIPLIER 1.0 // G26 Q (retraction) used by default between mesh test elements.
  1956. #endif
  1957.  
  1958. #endif
  1959.  
  1960. #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
  1961.  
  1962. // Set the number of grid points per dimension.
  1963. #define GRID_MAX_POINTS_X 3
  1964. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1965.  
  1966. // Probe along the Y axis, advancing X after each column
  1967. //#define PROBE_Y_FIRST
  1968.  
  1969. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  1970.  
  1971. // Beyond the probed grid, continue the implied tilt?
  1972. // Default is to maintain the height of the nearest edge.
  1973. //#define EXTRAPOLATE_BEYOND_GRID
  1974.  
  1975. //
  1976. // Experimental Subdivision of the grid by Catmull-Rom method.
  1977. // Synthesizes intermediate points to produce a more detailed mesh.
  1978. //
  1979. //#define ABL_BILINEAR_SUBDIVISION
  1980. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  1981. // Number of subdivisions between probe points
  1982. #define BILINEAR_SUBDIVISIONS 3
  1983. #endif
  1984.  
  1985. #endif
  1986.  
  1987. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  1988.  
  1989. //===========================================================================
  1990. //========================= Unified Bed Leveling ============================
  1991. //===========================================================================
  1992.  
  1993. //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
  1994.  
  1995. #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
  1996. #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
  1997. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  1998.  
  1999. //#define UBL_HILBERT_CURVE // Use Hilbert distribution for less travel when probing multiple points
  2000.  
  2001. #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
  2002. #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
  2003.  
  2004. //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
  2005. // as the Z-Height correction value.
  2006.  
  2007. //#define UBL_MESH_WIZARD // Run several commands in a row to get a complete mesh
  2008.  
  2009. #elif ENABLED(MESH_BED_LEVELING)
  2010.  
  2011. //===========================================================================
  2012. //=================================== Mesh ==================================
  2013. //===========================================================================
  2014.  
  2015. #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
  2016. #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
  2017. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  2018.  
  2019. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  2020.  
  2021. #endif // BED_LEVELING
  2022.  
  2023. /**
  2024. * Add a bed leveling sub-menu for ABL or MBL.
  2025. * Include a guided procedure if manual probing is enabled.
  2026. */
  2027. //#define LCD_BED_LEVELING
  2028.  
  2029. #if ENABLED(LCD_BED_LEVELING)
  2030. #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
  2031. #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
  2032. //#define MESH_EDIT_MENU // Add a menu to edit mesh points
  2033. #endif
  2034.  
  2035. // Add a menu item to move between bed corners for manual bed adjustment
  2036. //#define LCD_BED_TRAMMING
  2037.  
  2038. #if ENABLED(LCD_BED_TRAMMING)
  2039. #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
  2040. #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points
  2041. #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points
  2042. //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner
  2043. //#define BED_TRAMMING_USE_PROBE
  2044. #if ENABLED(BED_TRAMMING_USE_PROBE)
  2045. #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm)
  2046. #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify
  2047. //#define BED_TRAMMING_AUDIO_FEEDBACK
  2048. #endif
  2049.  
  2050. /**
  2051. * Corner Leveling Order
  2052. *
  2053. * Set 2 or 4 points. When 2 points are given, the 3rd is the center of the opposite edge.
  2054. *
  2055. * LF Left-Front RF Right-Front
  2056. * LB Left-Back RB Right-Back
  2057. *
  2058. * Examples:
  2059. *
  2060. * Default {LF,RB,LB,RF} {LF,RF} {LB,LF}
  2061. * LB --------- RB LB --------- RB LB --------- RB LB --------- RB
  2062. * | 4 3 | | 3 2 | | <3> | | 1 |
  2063. * | | | | | | | <3>|
  2064. * | 1 2 | | 1 4 | | 1 2 | | 2 |
  2065. * LF --------- RF LF --------- RF LF --------- RF LF --------- RF
  2066. */
  2067. #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB }
  2068. #endif
  2069.  
  2070. /**
  2071. * Commands to execute at the end of G29 probing.
  2072. * Useful to retract or move the Z probe out of the way.
  2073. */
  2074. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  2075.  
  2076. // @section homing
  2077.  
  2078. // The center of the bed is at (X=0, Y=0)
  2079. //#define BED_CENTER_AT_0_0
  2080.  
  2081. // Manually set the home position. Leave these undefined for automatic settings.
  2082. // For DELTA this is the top-center of the Cartesian print volume.
  2083. //#define MANUAL_X_HOME_POS 0
  2084. //#define MANUAL_Y_HOME_POS 0
  2085. //#define MANUAL_Z_HOME_POS 0
  2086. //#define MANUAL_I_HOME_POS 0
  2087. //#define MANUAL_J_HOME_POS 0
  2088. //#define MANUAL_K_HOME_POS 0
  2089. //#define MANUAL_U_HOME_POS 0
  2090. //#define MANUAL_V_HOME_POS 0
  2091. //#define MANUAL_W_HOME_POS 0
  2092.  
  2093. /**
  2094. * Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  2095. *
  2096. * - Moves the Z probe (or nozzle) to a defined XY point before Z homing.
  2097. * - Allows Z homing only when XY positions are known and trusted.
  2098. * - If stepper drivers sleep, XY homing may be required again before Z homing.
  2099. */
  2100. #define Z_SAFE_HOMING
  2101.  
  2102. #if ENABLED(Z_SAFE_HOMING)
  2103. #define Z_SAFE_HOMING_X_POINT X_CENTER // X point for Z homing
  2104. #define Z_SAFE_HOMING_Y_POINT Y_CENTER // Y point for Z homing
  2105. #endif
  2106.  
  2107. // Homing speeds (linear=mm/min, rotational=°/min)
  2108. #define HOMING_FEEDRATE_MM_M { (100*60), (100*60), (4*60) }
  2109.  
  2110. // Validate that endstops are triggered on homing moves
  2111. #define VALIDATE_HOMING_ENDSTOPS
  2112.  
  2113. // @section calibrate
  2114.  
  2115. /**
  2116. * Bed Skew Compensation
  2117. *
  2118. * This feature corrects for misalignment in the XYZ axes.
  2119. *
  2120. * Take the following steps to get the bed skew in the XY plane:
  2121. * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  2122. * 2. For XY_DIAG_AC measure the diagonal A to C
  2123. * 3. For XY_DIAG_BD measure the diagonal B to D
  2124. * 4. For XY_SIDE_AD measure the edge A to D
  2125. *
  2126. * Marlin automatically computes skew factors from these measurements.
  2127. * Skew factors may also be computed and set manually:
  2128. *
  2129. * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  2130. * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  2131. *
  2132. * If desired, follow the same procedure for XZ and YZ.
  2133. * Use these diagrams for reference:
  2134. *
  2135. * Y Z Z
  2136. * ^ B-------C ^ B-------C ^ B-------C
  2137. * | / / | / / | / /
  2138. * | / / | / / | / /
  2139. * | A-------D | A-------D | A-------D
  2140. * +-------------->X +-------------->X +-------------->Y
  2141. * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR
  2142. */
  2143. //#define SKEW_CORRECTION
  2144.  
  2145. #if ENABLED(SKEW_CORRECTION)
  2146. // Input all length measurements here:
  2147. #define XY_DIAG_AC 282.8427124746
  2148. #define XY_DIAG_BD 282.8427124746
  2149. #define XY_SIDE_AD 200
  2150.  
  2151. // Or, set the XY skew factor directly:
  2152. //#define XY_SKEW_FACTOR 0.0
  2153.  
  2154. //#define SKEW_CORRECTION_FOR_Z
  2155. #if ENABLED(SKEW_CORRECTION_FOR_Z)
  2156. #define XZ_DIAG_AC 282.8427124746
  2157. #define XZ_DIAG_BD 282.8427124746
  2158. #define YZ_DIAG_AC 282.8427124746
  2159. #define YZ_DIAG_BD 282.8427124746
  2160. #define YZ_SIDE_AD 200
  2161.  
  2162. // Or, set the Z skew factors directly:
  2163. //#define XZ_SKEW_FACTOR 0.0
  2164. //#define YZ_SKEW_FACTOR 0.0
  2165. #endif
  2166.  
  2167. // Enable this option for M852 to set skew at runtime
  2168. //#define SKEW_CORRECTION_GCODE
  2169. #endif
  2170.  
  2171. //=============================================================================
  2172. //============================= Additional Features ===========================
  2173. //=============================================================================
  2174.  
  2175. // @section eeprom
  2176.  
  2177. /**
  2178. * EEPROM
  2179. *
  2180. * Persistent storage to preserve configurable settings across reboots.
  2181. *
  2182. * M500 - Store settings to EEPROM.
  2183. * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  2184. * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  2185. */
  2186. #define EEPROM_SETTINGS // Persistent storage with M500 and M501
  2187. //#define DISABLE_M503 // Saves ~2700 bytes of flash. Disable for release!
  2188. #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
  2189. #define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
  2190. #if ENABLED(EEPROM_SETTINGS)
  2191. //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
  2192. //#define EEPROM_INIT_NOW // Init EEPROM on first boot after a new build.
  2193. #endif
  2194.  
  2195. // @section host
  2196.  
  2197. //
  2198. // Host Keepalive
  2199. //
  2200. // When enabled Marlin will send a busy status message to the host
  2201. // every couple of seconds when it can't accept commands.
  2202. //
  2203. //#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  2204. //#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  2205. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
  2206.  
  2207. // @section units
  2208.  
  2209. //
  2210. // G20/G21 Inch mode support
  2211. //
  2212. //#define INCH_MODE_SUPPORT
  2213.  
  2214. //
  2215. // M149 Set temperature units support
  2216. //
  2217. //#define TEMPERATURE_UNITS_SUPPORT
  2218.  
  2219. // @section temperature
  2220.  
  2221. //
  2222. // Preheat Constants - Up to 10 are supported without changes
  2223. //
  2224. #define PREHEAT_1_LABEL "PLA"
  2225. #define PREHEAT_1_TEMP_HOTEND 190
  2226. #define PREHEAT_1_TEMP_BED 60
  2227. #define PREHEAT_1_TEMP_CHAMBER 35
  2228. #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
  2229.  
  2230. #define PREHEAT_2_LABEL "ABS"
  2231. #define PREHEAT_2_TEMP_HOTEND 240
  2232. #define PREHEAT_2_TEMP_BED 90
  2233. #define PREHEAT_2_TEMP_CHAMBER 35
  2234. #define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
  2235.  
  2236. // @section motion
  2237.  
  2238. /**
  2239. * Nozzle Park
  2240. *
  2241. * Park the nozzle at the given XYZ position on idle or G27.
  2242. *
  2243. * The "P" parameter controls the action applied to the Z axis:
  2244. *
  2245. * P0 (Default) If Z is below park Z raise the nozzle.
  2246. * P1 Raise the nozzle always to Z-park height.
  2247. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  2248. */
  2249. //#define NOZZLE_PARK_FEATURE
  2250.  
  2251. #if ENABLED(NOZZLE_PARK_FEATURE)
  2252. // Specify a park position as { X, Y, Z_raise }
  2253. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  2254. #define NOZZLE_PARK_MOVE 0 // Park motion: 0 = XY Move, 1 = X Only, 2 = Y Only, 3 = X before Y, 4 = Y before X
  2255. #define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
  2256. #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
  2257. #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
  2258. #endif
  2259.  
  2260. /**
  2261. * Clean Nozzle Feature -- EXPERIMENTAL
  2262. *
  2263. * Adds the G12 command to perform a nozzle cleaning process.
  2264. *
  2265. * Parameters:
  2266. * P Pattern
  2267. * S Strokes / Repetitions
  2268. * T Triangles (P1 only)
  2269. *
  2270. * Patterns:
  2271. * P0 Straight line (default). This process requires a sponge type material
  2272. * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  2273. * between the start / end points.
  2274. *
  2275. * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  2276. * number of zig-zag triangles to do. "S" defines the number of strokes.
  2277. * Zig-zags are done in whichever is the narrower dimension.
  2278. * For example, "G12 P1 S1 T3" will execute:
  2279. *
  2280. * --
  2281. * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  2282. * | | / \ / \ / \ |
  2283. * A | | / \ / \ / \ |
  2284. * | | / \ / \ / \ |
  2285. * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  2286. * -- +--------------------------------+
  2287. * |________|_________|_________|
  2288. * T1 T2 T3
  2289. *
  2290. * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  2291. * "R" specifies the radius. "S" specifies the stroke count.
  2292. * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  2293. *
  2294. * Caveats: The ending Z should be the same as starting Z.
  2295. * Attention: EXPERIMENTAL. G-code arguments may change.
  2296. */
  2297. //#define NOZZLE_CLEAN_FEATURE
  2298.  
  2299. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  2300. // Default number of pattern repetitions
  2301. #define NOZZLE_CLEAN_STROKES 12
  2302.  
  2303. // Default number of triangles
  2304. #define NOZZLE_CLEAN_TRIANGLES 3
  2305.  
  2306. // Specify positions for each tool as { { X, Y, Z }, { X, Y, Z } }
  2307. // Dual hotend system may use { { -20, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }, { 420, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }}
  2308. #define NOZZLE_CLEAN_START_POINT { { 30, 30, (Z_MIN_POS + 1) } }
  2309. #define NOZZLE_CLEAN_END_POINT { { 100, 60, (Z_MIN_POS + 1) } }
  2310.  
  2311. // Circular pattern radius
  2312. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  2313. // Circular pattern circle fragments number
  2314. #define NOZZLE_CLEAN_CIRCLE_FN 10
  2315. // Middle point of circle
  2316. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  2317.  
  2318. // Move the nozzle to the initial position after cleaning
  2319. #define NOZZLE_CLEAN_GOBACK
  2320.  
  2321. // For a purge/clean station that's always at the gantry height (thus no Z move)
  2322. //#define NOZZLE_CLEAN_NO_Z
  2323.  
  2324. // For a purge/clean station mounted on the X axis
  2325. //#define NOZZLE_CLEAN_NO_Y
  2326.  
  2327. // Require a minimum hotend temperature for cleaning
  2328. #define NOZZLE_CLEAN_MIN_TEMP 170
  2329. //#define NOZZLE_CLEAN_HEATUP // Heat up the nozzle instead of skipping wipe
  2330.  
  2331. // Explicit wipe G-code script applies to a G12 with no arguments.
  2332. //#define WIPE_SEQUENCE_COMMANDS "G1 X-17 Y25 Z10 F4000\nG1 Z1\nM114\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 Z15\nM400\nG0 X-10.0 Y-9.0"
  2333.  
  2334. #endif
  2335.  
  2336. // @section host
  2337.  
  2338. /**
  2339. * Print Job Timer
  2340. *
  2341. * Automatically start and stop the print job timer on M104/M109/M140/M190/M141/M191.
  2342. * The print job timer will only be stopped if the bed/chamber target temp is
  2343. * below BED_MINTEMP/CHAMBER_MINTEMP.
  2344. *
  2345. * M104 (hotend, no wait) - high temp = none, low temp = stop timer
  2346. * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
  2347. * M140 (bed, no wait) - high temp = none, low temp = stop timer
  2348. * M190 (bed, wait) - high temp = start timer, low temp = none
  2349. * M141 (chamber, no wait) - high temp = none, low temp = stop timer
  2350. * M191 (chamber, wait) - high temp = start timer, low temp = none
  2351. *
  2352. * For M104/M109, high temp is anything over EXTRUDE_MINTEMP / 2.
  2353. * For M140/M190, high temp is anything over BED_MINTEMP.
  2354. * For M141/M191, high temp is anything over CHAMBER_MINTEMP.
  2355. *
  2356. * The timer can also be controlled with the following commands:
  2357. *
  2358. * M75 - Start the print job timer
  2359. * M76 - Pause the print job timer
  2360. * M77 - Stop the print job timer
  2361. */
  2362. #define PRINTJOB_TIMER_AUTOSTART
  2363.  
  2364. // @section stats
  2365.  
  2366. /**
  2367. * Print Counter
  2368. *
  2369. * Track statistical data such as:
  2370. *
  2371. * - Total print jobs
  2372. * - Total successful print jobs
  2373. * - Total failed print jobs
  2374. * - Total time printing
  2375. *
  2376. * View the current statistics with M78.
  2377. */
  2378. //#define PRINTCOUNTER
  2379. #if ENABLED(PRINTCOUNTER)
  2380. #define PRINTCOUNTER_SAVE_INTERVAL 60 // (minutes) EEPROM save interval during print. A value of 0 will save stats at end of print.
  2381. #endif
  2382.  
  2383. // @section security
  2384.  
  2385. /**
  2386. * Password
  2387. *
  2388. * Set a numerical password for the printer which can be requested:
  2389. *
  2390. * - When the printer boots up
  2391. * - Upon opening the 'Print from Media' Menu
  2392. * - When SD printing is completed or aborted
  2393. *
  2394. * The following G-codes can be used:
  2395. *
  2396. * M510 - Lock Printer. Blocks all commands except M511.
  2397. * M511 - Unlock Printer.
  2398. * M512 - Set, Change and Remove Password.
  2399. *
  2400. * If you forget the password and get locked out you'll need to re-flash
  2401. * the firmware with the feature disabled, reset EEPROM, and (optionally)
  2402. * re-flash the firmware again with this feature enabled.
  2403. */
  2404. //#define PASSWORD_FEATURE
  2405. #if ENABLED(PASSWORD_FEATURE)
  2406. #define PASSWORD_LENGTH 4 // (#) Number of digits (1-9). 3 or 4 is recommended
  2407. #define PASSWORD_ON_STARTUP
  2408. #define PASSWORD_UNLOCK_GCODE // Unlock with the M511 P<password> command. Disable to prevent brute-force attack.
  2409. #define PASSWORD_CHANGE_GCODE // Change the password with M512 P<old> S<new>.
  2410. //#define PASSWORD_ON_SD_PRINT_MENU // This does not prevent gcodes from running
  2411. //#define PASSWORD_AFTER_SD_PRINT_END
  2412. //#define PASSWORD_AFTER_SD_PRINT_ABORT
  2413. //#include "Configuration_Secure.h" // External file with PASSWORD_DEFAULT_VALUE
  2414. #endif
  2415.  
  2416. //=============================================================================
  2417. //============================= LCD and SD support ============================
  2418. //=============================================================================
  2419.  
  2420. // @section interface
  2421.  
  2422. /**
  2423. * LCD LANGUAGE
  2424. *
  2425. * Select the language to display on the LCD. These languages are available:
  2426. *
  2427. * en, an, bg, ca, cz, da, de, el, el_CY, es, eu, fi, fr, gl, hr, hu, it,
  2428. * jp_kana, ko_KR, nl, pl, pt, pt_br, ro, ru, sk, sv, tr, uk, vi, zh_CN, zh_TW
  2429. *
  2430. * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek (Greece)', 'el_CY':'Greek (Cyprus)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'hu':'Hungarian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ro':'Romanian', 'ru':'Russian', 'sk':'Slovak', 'sv':'Swedish', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)' }
  2431. */
  2432. #define LCD_LANGUAGE en
  2433.  
  2434. /**
  2435. * LCD Character Set
  2436. *
  2437. * Note: This option is NOT applicable to Graphical Displays.
  2438. *
  2439. * All character-based LCDs provide ASCII plus one of these
  2440. * language extensions:
  2441. *
  2442. * - JAPANESE ... the most common
  2443. * - WESTERN ... with more accented characters
  2444. * - CYRILLIC ... for the Russian language
  2445. *
  2446. * To determine the language extension installed on your controller:
  2447. *
  2448. * - Compile and upload with LCD_LANGUAGE set to 'test'
  2449. * - Click the controller to view the LCD menu
  2450. * - The LCD will display Japanese, Western, or Cyrillic text
  2451. *
  2452. * See https://marlinfw.org/docs/development/lcd_language.html
  2453. *
  2454. * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  2455. */
  2456. #define DISPLAY_CHARSET_HD44780 JAPANESE
  2457.  
  2458. /**
  2459. * Info Screen Style (0:Classic, 1:Průša)
  2460. *
  2461. * :[0:'Classic', 1:'Průša']
  2462. */
  2463. #define LCD_INFO_SCREEN_STYLE 0
  2464.  
  2465. /**
  2466. * SD CARD
  2467. *
  2468. * SD Card support is disabled by default. If your controller has an SD slot,
  2469. * you must uncomment the following option or it won't work.
  2470. */
  2471. #define SDSUPPORT
  2472.  
  2473. /**
  2474. * SD CARD: ENABLE CRC
  2475. *
  2476. * Use CRC checks and retries on the SD communication.
  2477. */
  2478. //#define SD_CHECK_AND_RETRY
  2479.  
  2480. /**
  2481. * LCD Menu Items
  2482. *
  2483. * Disable all menus and only display the Status Screen, or
  2484. * just remove some extraneous menu items to recover space.
  2485. */
  2486. //#define NO_LCD_MENUS
  2487. //#define SLIM_LCD_MENUS
  2488.  
  2489. //
  2490. // ENCODER SETTINGS
  2491. //
  2492. // This option overrides the default number of encoder pulses needed to
  2493. // produce one step. Should be increased for high-resolution encoders.
  2494. //
  2495. //#define ENCODER_PULSES_PER_STEP 4
  2496.  
  2497. //
  2498. // Use this option to override the number of step signals required to
  2499. // move between next/prev menu items.
  2500. //
  2501. //#define ENCODER_STEPS_PER_MENU_ITEM 1
  2502.  
  2503. /**
  2504. * Encoder Direction Options
  2505. *
  2506. * Test your encoder's behavior first with both options disabled.
  2507. *
  2508. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  2509. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  2510. * Reversed Value Editing only? Enable BOTH options.
  2511. */
  2512.  
  2513. //
  2514. // This option reverses the encoder direction everywhere.
  2515. //
  2516. // Set this option if CLOCKWISE causes values to DECREASE
  2517. //
  2518. //#define REVERSE_ENCODER_DIRECTION
  2519.  
  2520. //
  2521. // This option reverses the encoder direction for navigating LCD menus.
  2522. //
  2523. // If CLOCKWISE normally moves DOWN this makes it go UP.
  2524. // If CLOCKWISE normally moves UP this makes it go DOWN.
  2525. //
  2526. //#define REVERSE_MENU_DIRECTION
  2527.  
  2528. //
  2529. // This option reverses the encoder direction for Select Screen.
  2530. //
  2531. // If CLOCKWISE normally moves LEFT this makes it go RIGHT.
  2532. // If CLOCKWISE normally moves RIGHT this makes it go LEFT.
  2533. //
  2534. //#define REVERSE_SELECT_DIRECTION
  2535.  
  2536. //
  2537. // Encoder EMI Noise Filter
  2538. //
  2539. // This option increases encoder samples to filter out phantom encoder clicks caused by EMI noise.
  2540. //
  2541. //#define ENCODER_NOISE_FILTER
  2542. #if ENABLED(ENCODER_NOISE_FILTER)
  2543. #define ENCODER_SAMPLES 10
  2544. #endif
  2545.  
  2546. //
  2547. // Individual Axis Homing
  2548. //
  2549. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  2550. //
  2551. //#define INDIVIDUAL_AXIS_HOMING_MENU
  2552. //#define INDIVIDUAL_AXIS_HOMING_SUBMENU
  2553.  
  2554. //
  2555. // SPEAKER/BUZZER
  2556. //
  2557. // If you have a speaker that can produce tones, enable it here.
  2558. // By default Marlin assumes you have a buzzer with a fixed frequency.
  2559. //
  2560. //#define SPEAKER
  2561.  
  2562. //
  2563. // The duration and frequency for the UI feedback sound.
  2564. // Set these to 0 to disable audio feedback in the LCD menus.
  2565. //
  2566. // Note: Test audio output with the G-Code:
  2567. // M300 S<frequency Hz> P<duration ms>
  2568. //
  2569. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
  2570. //#define LCD_FEEDBACK_FREQUENCY_HZ 5000
  2571.  
  2572. //=============================================================================
  2573. //======================== LCD / Controller Selection =========================
  2574. //======================== (Character-based LCDs) =========================
  2575. //=============================================================================
  2576. // @section lcd
  2577.  
  2578. //
  2579. // RepRapDiscount Smart Controller.
  2580. // https://reprap.org/wiki/RepRapDiscount_Smart_Controller
  2581. //
  2582. // Note: Usually sold with a white PCB.
  2583. //
  2584. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  2585.  
  2586. //
  2587. // GT2560 (YHCB2004) LCD Display
  2588. //
  2589. // Requires Testato, Koepel softwarewire library and
  2590. // Andriy Golovnya's LiquidCrystal_AIP31068 library.
  2591. //
  2592. //#define YHCB2004
  2593.  
  2594. //
  2595. // Original RADDS LCD Display+Encoder+SDCardReader
  2596. // http://doku.radds.org/dokumentation/lcd-display/
  2597. //
  2598. //#define RADDS_DISPLAY
  2599.  
  2600. //
  2601. // ULTIMAKER Controller.
  2602. //
  2603. //#define ULTIMAKERCONTROLLER
  2604.  
  2605. //
  2606. // ULTIPANEL as seen on Thingiverse.
  2607. //
  2608. //#define ULTIPANEL
  2609.  
  2610. //
  2611. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  2612. // https://reprap.org/wiki/PanelOne
  2613. //
  2614. //#define PANEL_ONE
  2615.  
  2616. //
  2617. // GADGETS3D G3D LCD/SD Controller
  2618. // https://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  2619. //
  2620. // Note: Usually sold with a blue PCB.
  2621. //
  2622. //#define G3D_PANEL
  2623.  
  2624. //
  2625. // RigidBot Panel V1.0
  2626. // http://www.inventapart.com/
  2627. //
  2628. //#define RIGIDBOT_PANEL
  2629.  
  2630. //
  2631. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  2632. // https://www.aliexpress.com/item/32765887917.html
  2633. //
  2634. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  2635.  
  2636. //
  2637. // ANET and Tronxy 20x4 Controller
  2638. //
  2639. //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. //EC disabled due to SKR incompatability
  2640. // This LCD is known to be susceptible to electrical interference
  2641. // which scrambles the display. Pressing any button clears it up.
  2642. // This is a LCD2004 display with 5 analog buttons.
  2643.  
  2644. //
  2645. // Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  2646. //
  2647. //#define ULTRA_LCD
  2648.  
  2649. //=============================================================================
  2650. //======================== LCD / Controller Selection =========================
  2651. //===================== (I2C and Shift-Register LCDs) =====================
  2652. //=============================================================================
  2653.  
  2654. //
  2655. // CONTROLLER TYPE: I2C
  2656. //
  2657. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  2658. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  2659. //
  2660.  
  2661. //
  2662. // Elefu RA Board Control Panel
  2663. // http://www.elefu.com/index.php?route=product/product&product_id=53
  2664. //
  2665. //#define RA_CONTROL_PANEL
  2666.  
  2667. //
  2668. // Sainsmart (YwRobot) LCD Displays
  2669. //
  2670. // These require F.Malpartida's LiquidCrystal_I2C library
  2671. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  2672. //
  2673. //#define LCD_SAINSMART_I2C_1602
  2674. //#define LCD_SAINSMART_I2C_2004
  2675.  
  2676. //
  2677. // Generic LCM1602 LCD adapter
  2678. //
  2679. //#define LCM1602
  2680.  
  2681. //
  2682. // PANELOLU2 LCD with status LEDs,
  2683. // separate encoder and click inputs.
  2684. //
  2685. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  2686. // For more info: https://github.com/lincomatic/LiquidTWI2
  2687. //
  2688. // Note: The PANELOLU2 encoder click input can either be directly connected to
  2689. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  2690. //
  2691. //#define LCD_I2C_PANELOLU2
  2692.  
  2693. //
  2694. // Panucatt VIKI LCD with status LEDs,
  2695. // integrated click & L/R/U/D buttons, separate encoder inputs.
  2696. //
  2697. //#define LCD_I2C_VIKI
  2698.  
  2699. //
  2700. // CONTROLLER TYPE: Shift register panels
  2701. //
  2702.  
  2703. //
  2704. // 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  2705. // LCD configuration: https://reprap.org/wiki/SAV_3D_LCD
  2706. //
  2707. //#define SAV_3DLCD
  2708.  
  2709. //
  2710. // 3-wire SR LCD with strobe using 74HC4094
  2711. // https://github.com/mikeshub/SailfishLCD
  2712. // Uses the code directly from Sailfish
  2713. //
  2714. //#define FF_INTERFACEBOARD
  2715.  
  2716. //
  2717. // TFT GLCD Panel with Marlin UI
  2718. // Panel connected to main board by SPI or I2C interface.
  2719. // See https://github.com/Serhiy-K/TFTGLCDAdapter
  2720. //
  2721. //#define TFTGLCD_PANEL_SPI
  2722. //#define TFTGLCD_PANEL_I2C
  2723.  
  2724. //=============================================================================
  2725. //======================= LCD / Controller Selection =======================
  2726. //========================= (Graphical LCDs) ========================
  2727. //=============================================================================
  2728.  
  2729. //
  2730. // CONTROLLER TYPE: Graphical 128x64 (DOGM)
  2731. //
  2732. // IMPORTANT: The U8glib library is required for Graphical Display!
  2733. // https://github.com/olikraus/U8glib_Arduino
  2734. //
  2735. // NOTE: If the LCD is unresponsive you may need to reverse the plugs.
  2736. //
  2737.  
  2738. //
  2739. // RepRapDiscount FULL GRAPHIC Smart Controller
  2740. // https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  2741. //
  2742. // Note: Details on connecting to the Anet V1.0 controller are in the file pins_ANET_10.h
  2743. //
  2744. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  2745.  
  2746. //
  2747. // K.3D Full Graphic Smart Controller
  2748. //
  2749. //#define K3D_FULL_GRAPHIC_SMART_CONTROLLER
  2750.  
  2751. //
  2752. // ReprapWorld Graphical LCD
  2753. // https://reprapworld.com/electronics/3d-printer-modules/autonomous-printing/graphical-lcd-screen-v1-0/
  2754. //
  2755. //#define REPRAPWORLD_GRAPHICAL_LCD
  2756.  
  2757. //
  2758. // Activate one of these if you have a Panucatt Devices
  2759. // Viki 2.0 or mini Viki with Graphic LCD
  2760. // https://www.panucatt.com
  2761. //
  2762. //#define VIKI2
  2763. //#define miniVIKI
  2764.  
  2765. //
  2766. // Alfawise Ex8 printer LCD marked as WYH L12864 COG
  2767. //
  2768. //#define WYH_L12864
  2769.  
  2770. //
  2771. // MakerLab Mini Panel with graphic
  2772. // controller and SD support - https://reprap.org/wiki/Mini_panel
  2773. //
  2774. //#define MINIPANEL
  2775.  
  2776. //
  2777. // MaKr3d Makr-Panel with graphic controller and SD support.
  2778. // https://reprap.org/wiki/MaKr3d_MaKrPanel
  2779. //
  2780. //#define MAKRPANEL
  2781.  
  2782. //
  2783. // Adafruit ST7565 Full Graphic Controller.
  2784. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  2785. //
  2786. //#define ELB_FULL_GRAPHIC_CONTROLLER
  2787.  
  2788. //
  2789. // BQ LCD Smart Controller shipped by
  2790. // default with the BQ Hephestos 2 and Witbox 2.
  2791. //
  2792. //#define BQ_LCD_SMART_CONTROLLER
  2793.  
  2794. //
  2795. // Cartesio UI
  2796. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  2797. //
  2798. //#define CARTESIO_UI
  2799.  
  2800. //
  2801. // LCD for Melzi Card with Graphical LCD
  2802. //
  2803. //#define LCD_FOR_MELZI
  2804.  
  2805. //
  2806. // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder
  2807. // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1)
  2808. //
  2809. //#define ULTI_CONTROLLER
  2810.  
  2811. //
  2812. // MKS MINI12864 with graphic controller and SD support
  2813. // https://reprap.org/wiki/MKS_MINI_12864
  2814. //
  2815. //#define MKS_MINI_12864
  2816.  
  2817. //
  2818. // MKS MINI12864 V3 is an alias for FYSETC_MINI_12864_2_1. Type A/B. NeoPixel RGB Backlight.
  2819. //
  2820. #define MKS_MINI_12864_V3 //EC
  2821.  
  2822. //
  2823. // MKS LCD12864A/B with graphic controller and SD support. Follows MKS_MINI_12864 pinout.
  2824. // https://www.aliexpress.com/item/33018110072.html
  2825. //
  2826. //#define MKS_LCD12864A
  2827. //#define MKS_LCD12864B
  2828.  
  2829. //
  2830. // FYSETC variant of the MINI12864 graphic controller with SD support
  2831. // https://wiki.fysetc.com/Mini12864_Panel/
  2832. //
  2833. //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default
  2834. //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on)
  2835. //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight
  2836. //#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight
  2837. //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight.
  2838.  
  2839. //
  2840. // BigTreeTech Mini 12864 V1.0 is an alias for FYSETC_MINI_12864_2_1. Type A/B. NeoPixel RGB Backlight.
  2841. //
  2842. //#define BTT_MINI_12864_V1
  2843.  
  2844. //
  2845. // Factory display for Creality CR-10
  2846. // https://www.aliexpress.com/item/32833148327.html
  2847. //
  2848. // This is RAMPS-compatible using a single 10-pin connector.
  2849. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  2850. //
  2851. //#define CR10_STOCKDISPLAY
  2852.  
  2853. //
  2854. // Ender-2 OEM display, a variant of the MKS_MINI_12864
  2855. //
  2856. //#define ENDER2_STOCKDISPLAY
  2857.  
  2858. //
  2859. // ANET and Tronxy Graphical Controller
  2860. //
  2861. // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  2862. // A clone of the RepRapDiscount full graphics display but with
  2863. // different pins/wiring (see pins_ANET_10.h). Enable one of these.
  2864. //
  2865. //#define ANET_FULL_GRAPHICS_LCD
  2866. //#define ANET_FULL_GRAPHICS_LCD_ALT_WIRING
  2867.  
  2868. //
  2869. // AZSMZ 12864 LCD with SD
  2870. // https://www.aliexpress.com/item/32837222770.html
  2871. //
  2872. //#define AZSMZ_12864
  2873.  
  2874. //
  2875. // Silvergate GLCD controller
  2876. // https://github.com/android444/Silvergate
  2877. //
  2878. //#define SILVER_GATE_GLCD_CONTROLLER
  2879.  
  2880. //
  2881. // eMotion Tech LCD with SD
  2882. // https://www.reprap-france.com/produit/1234568748-ecran-graphique-128-x-64-points-2-1
  2883. //
  2884. //#define EMOTION_TECH_LCD
  2885.  
  2886. //=============================================================================
  2887. //============================== OLED Displays ==============================
  2888. //=============================================================================
  2889.  
  2890. //
  2891. // SSD1306 OLED full graphics generic display
  2892. //
  2893. //#define U8GLIB_SSD1306
  2894.  
  2895. //
  2896. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  2897. //
  2898. //#define SAV_3DGLCD
  2899. #if ENABLED(SAV_3DGLCD)
  2900. #define U8GLIB_SSD1306
  2901. //#define U8GLIB_SH1106
  2902. #endif
  2903.  
  2904. //
  2905. // TinyBoy2 128x64 OLED / Encoder Panel
  2906. //
  2907. //#define OLED_PANEL_TINYBOY2
  2908.  
  2909. //
  2910. // MKS OLED 1.3" 128×64 Full Graphics Controller
  2911. // https://reprap.org/wiki/MKS_12864OLED
  2912. //
  2913. // Tiny, but very sharp OLED display
  2914. //
  2915. //#define MKS_12864OLED // Uses the SH1106 controller (default)
  2916. //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
  2917.  
  2918. //
  2919. // Zonestar OLED 128×64 Full Graphics Controller
  2920. //
  2921. //#define ZONESTAR_12864LCD // Graphical (DOGM) with ST7920 controller
  2922. //#define ZONESTAR_12864OLED // 1.3" OLED with SH1106 controller (default)
  2923. //#define ZONESTAR_12864OLED_SSD1306 // 0.96" OLED with SSD1306 controller
  2924.  
  2925. //
  2926. // Einstart S OLED SSD1306
  2927. //
  2928. //#define U8GLIB_SH1106_EINSTART
  2929.  
  2930. //
  2931. // Overlord OLED display/controller with i2c buzzer and LEDs
  2932. //
  2933. //#define OVERLORD_OLED
  2934.  
  2935. //
  2936. // FYSETC OLED 2.42" 128×64 Full Graphics Controller with WS2812 RGB
  2937. // Where to find : https://www.aliexpress.com/item/4000345255731.html
  2938. //#define FYSETC_242_OLED_12864 // Uses the SSD1309 controller
  2939.  
  2940. //
  2941. // K.3D SSD1309 OLED 2.42" 128×64 Full Graphics Controller
  2942. //
  2943. //#define K3D_242_OLED_CONTROLLER // Software SPI
  2944.  
  2945. //=============================================================================
  2946. //========================== Extensible UI Displays ===========================
  2947. //=============================================================================
  2948.  
  2949. /**
  2950. * DGUS Touch Display with DWIN OS. (Choose one.)
  2951. * ORIGIN : https://www.aliexpress.com/item/32993409517.html
  2952. * FYSETC : https://www.aliexpress.com/item/32961471929.html
  2953. * MKS : https://www.aliexpress.com/item/1005002008179262.html
  2954. *
  2955. * Flash display with DGUS Displays for Marlin:
  2956. * - Format the SD card to FAT32 with an allocation size of 4kb.
  2957. * - Download files as specified for your type of display.
  2958. * - Plug the microSD card into the back of the display.
  2959. * - Boot the display and wait for the update to complete.
  2960. *
  2961. * ORIGIN (Marlin DWIN_SET)
  2962. * - Download https://github.com/coldtobi/Marlin_DGUS_Resources
  2963. * - Copy the downloaded DWIN_SET folder to the SD card.
  2964. *
  2965. * FYSETC (Supplier default)
  2966. * - Download https://github.com/FYSETC/FYSTLCD-2.0
  2967. * - Copy the downloaded SCREEN folder to the SD card.
  2968. *
  2969. * HIPRECY (Supplier default)
  2970. * - Download https://github.com/HiPrecy/Touch-Lcd-LEO
  2971. * - Copy the downloaded DWIN_SET folder to the SD card.
  2972. *
  2973. * MKS (MKS-H43) (Supplier default)
  2974. * - Download https://github.com/makerbase-mks/MKS-H43
  2975. * - Copy the downloaded DWIN_SET folder to the SD card.
  2976. *
  2977. * RELOADED (T5UID1)
  2978. * - Download https://github.com/Desuuuu/DGUS-reloaded/releases
  2979. * - Copy the downloaded DWIN_SET folder to the SD card.
  2980. */
  2981. //#define DGUS_LCD_UI_ORIGIN
  2982. //#define DGUS_LCD_UI_FYSETC
  2983. //#define DGUS_LCD_UI_HIPRECY
  2984. //#define DGUS_LCD_UI_MKS
  2985. //#define DGUS_LCD_UI_RELOADED
  2986. #if ENABLED(DGUS_LCD_UI_MKS)
  2987. #define USE_MKS_GREEN_UI
  2988. #endif
  2989.  
  2990. //
  2991. // Touch-screen LCD for Malyan M200/M300 printers
  2992. //
  2993. //#define MALYAN_LCD
  2994.  
  2995. //
  2996. // Touch UI for FTDI EVE (FT800/FT810) displays
  2997. // See Configuration_adv.h for all configuration options.
  2998. //
  2999. //#define TOUCH_UI_FTDI_EVE
  3000.  
  3001. //
  3002. // Touch-screen LCD for Anycubic printers
  3003. //
  3004. //#define ANYCUBIC_LCD_I3MEGA
  3005. //#define ANYCUBIC_LCD_CHIRON
  3006. #if EITHER(ANYCUBIC_LCD_I3MEGA, ANYCUBIC_LCD_CHIRON)
  3007. //#define ANYCUBIC_LCD_DEBUG
  3008. //#define ANYCUBIC_LCD_GCODE_EXT // Add ".gcode" to menu entries for DGUS clone compatibility
  3009. #endif
  3010.  
  3011. //
  3012. // 320x240 Nextion 2.8" serial TFT Resistive Touch Screen NX3224T028
  3013. //
  3014. //#define NEXTION_TFT
  3015.  
  3016. //
  3017. // Third-party or vendor-customized controller interfaces.
  3018. // Sources should be installed in 'src/lcd/extui'.
  3019. //
  3020. //#define EXTENSIBLE_UI
  3021.  
  3022. #if ENABLED(EXTENSIBLE_UI)
  3023. //#define EXTUI_LOCAL_BEEPER // Enables use of local Beeper pin with external display
  3024. #endif
  3025.  
  3026. //=============================================================================
  3027. //=============================== Graphical TFTs ==============================
  3028. //=============================================================================
  3029.  
  3030. /**
  3031. * Specific TFT Model Presets. Enable one of the following options
  3032. * or enable TFT_GENERIC and set sub-options.
  3033. */
  3034.  
  3035. //
  3036. // 480x320, 3.5", SPI Display with Rotary Encoder from MKS
  3037. // Usually paired with MKS Robin Nano V2 & V3
  3038. //
  3039. //#define MKS_TS35_V2_0
  3040.  
  3041. //
  3042. // 320x240, 2.4", FSMC Display From MKS
  3043. // Usually paired with MKS Robin Nano V1.2
  3044. //
  3045. //#define MKS_ROBIN_TFT24
  3046.  
  3047. //
  3048. // 320x240, 2.8", FSMC Display From MKS
  3049. // Usually paired with MKS Robin Nano V1.2
  3050. //
  3051. //#define MKS_ROBIN_TFT28
  3052.  
  3053. //
  3054. // 320x240, 3.2", FSMC Display From MKS
  3055. // Usually paired with MKS Robin Nano V1.2
  3056. //
  3057. //#define MKS_ROBIN_TFT32
  3058.  
  3059. //
  3060. // 480x320, 3.5", FSMC Display From MKS
  3061. // Usually paired with MKS Robin Nano V1.2
  3062. //
  3063. //#define MKS_ROBIN_TFT35
  3064.  
  3065. //
  3066. // 480x272, 4.3", FSMC Display From MKS
  3067. //
  3068. //#define MKS_ROBIN_TFT43
  3069.  
  3070. //
  3071. // 320x240, 3.2", FSMC Display From MKS
  3072. // Usually paired with MKS Robin
  3073. //
  3074. //#define MKS_ROBIN_TFT_V1_1R
  3075.  
  3076. //
  3077. // 480x320, 3.5", FSMC Stock Display from Tronxy
  3078. //
  3079. //#define TFT_TRONXY_X5SA
  3080.  
  3081. //
  3082. // 480x320, 3.5", FSMC Stock Display from AnyCubic
  3083. //
  3084. //#define ANYCUBIC_TFT35
  3085.  
  3086. //
  3087. // 320x240, 2.8", FSMC Stock Display from Longer/Alfawise
  3088. //
  3089. //#define LONGER_LK_TFT28
  3090.  
  3091. //
  3092. // 320x240, 2.8", FSMC Stock Display from ET4
  3093. //
  3094. //#define ANET_ET4_TFT28
  3095.  
  3096. //
  3097. // 480x320, 3.5", FSMC Stock Display from ET5
  3098. //
  3099. //#define ANET_ET5_TFT35
  3100.  
  3101. //
  3102. // 1024x600, 7", RGB Stock Display with Rotary Encoder from BIQU-BX
  3103. //
  3104. //#define BIQU_BX_TFT70
  3105.  
  3106. //
  3107. // 480x320, 3.5", SPI Stock Display with Rotary Encoder from BIQU B1 SE Series
  3108. //
  3109. //#define BTT_TFT35_SPI_V1_0
  3110.  
  3111. //
  3112. // Generic TFT with detailed options
  3113. //
  3114. //#define TFT_GENERIC
  3115. #if ENABLED(TFT_GENERIC)
  3116. // :[ 'AUTO', 'ST7735', 'ST7789', 'ST7796', 'R61505', 'ILI9328', 'ILI9341', 'ILI9488' ]
  3117. #define TFT_DRIVER AUTO
  3118.  
  3119. // Interface. Enable one of the following options:
  3120. //#define TFT_INTERFACE_FSMC
  3121. //#define TFT_INTERFACE_SPI
  3122.  
  3123. // TFT Resolution. Enable one of the following options:
  3124. //#define TFT_RES_320x240
  3125. //#define TFT_RES_480x272
  3126. //#define TFT_RES_480x320
  3127. //#define TFT_RES_1024x600
  3128. #endif
  3129.  
  3130. /**
  3131. * TFT UI - User Interface Selection. Enable one of the following options:
  3132. *
  3133. * TFT_CLASSIC_UI - Emulated DOGM - 128x64 Upscaled
  3134. * TFT_COLOR_UI - Marlin Default Menus, Touch Friendly, using full TFT capabilities
  3135. * TFT_LVGL_UI - A Modern UI using LVGL
  3136. *
  3137. * For LVGL_UI also copy the 'assets' folder from the build directory to the
  3138. * root of your SD card, together with the compiled firmware.
  3139. */
  3140. //#define TFT_CLASSIC_UI
  3141. //#define TFT_COLOR_UI
  3142. //#define TFT_LVGL_UI
  3143.  
  3144. #if ENABLED(TFT_COLOR_UI)
  3145. //#define TFT_SHARED_SPI // SPI is shared between TFT display and other devices. Disable async data transfer
  3146. #endif
  3147.  
  3148. #if ENABLED(TFT_LVGL_UI)
  3149. //#define MKS_WIFI_MODULE // MKS WiFi module
  3150. #endif
  3151.  
  3152. /**
  3153. * TFT Rotation. Set to one of the following values:
  3154. *
  3155. * TFT_ROTATE_90, TFT_ROTATE_90_MIRROR_X, TFT_ROTATE_90_MIRROR_Y,
  3156. * TFT_ROTATE_180, TFT_ROTATE_180_MIRROR_X, TFT_ROTATE_180_MIRROR_Y,
  3157. * TFT_ROTATE_270, TFT_ROTATE_270_MIRROR_X, TFT_ROTATE_270_MIRROR_Y,
  3158. * TFT_MIRROR_X, TFT_MIRROR_Y, TFT_NO_ROTATION
  3159. */
  3160. //#define TFT_ROTATION TFT_NO_ROTATION
  3161.  
  3162. //=============================================================================
  3163. //============================ Other Controllers ============================
  3164. //=============================================================================
  3165.  
  3166. //
  3167. // Ender-3 v2 OEM display. A DWIN display with Rotary Encoder.
  3168. //
  3169. //#define DWIN_CREALITY_LCD // Creality UI
  3170. //#define DWIN_LCD_PROUI // Pro UI by MRiscoC
  3171. //#define DWIN_CREALITY_LCD_JYERSUI // Jyers UI by Jacob Myers
  3172. //#define DWIN_MARLINUI_PORTRAIT // MarlinUI (portrait orientation)
  3173. //#define DWIN_MARLINUI_LANDSCAPE // MarlinUI (landscape orientation)
  3174.  
  3175. //
  3176. // Touch Screen Settings
  3177. //
  3178. //#define TOUCH_SCREEN
  3179. #if ENABLED(TOUCH_SCREEN)
  3180. #define BUTTON_DELAY_EDIT 50 // (ms) Button repeat delay for edit screens
  3181. #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
  3182.  
  3183. //#define DISABLE_ENCODER // Disable the click encoder, if any
  3184. //#define TOUCH_IDLE_SLEEP_MINS 5 // (minutes) Display Sleep after a period of inactivity. Set with M255 S.
  3185.  
  3186. #define TOUCH_SCREEN_CALIBRATION
  3187.  
  3188. //#define TOUCH_CALIBRATION_X 12316
  3189. //#define TOUCH_CALIBRATION_Y -8981
  3190. //#define TOUCH_OFFSET_X -43
  3191. //#define TOUCH_OFFSET_Y 257
  3192. //#define TOUCH_ORIENTATION TOUCH_LANDSCAPE
  3193.  
  3194. #if BOTH(TOUCH_SCREEN_CALIBRATION, EEPROM_SETTINGS)
  3195. #define TOUCH_CALIBRATION_AUTO_SAVE // Auto save successful calibration values to EEPROM
  3196. #endif
  3197.  
  3198. #if ENABLED(TFT_COLOR_UI)
  3199. //#define SINGLE_TOUCH_NAVIGATION
  3200. #endif
  3201. #endif
  3202.  
  3203. //
  3204. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  3205. // https://reprapworld.com/products/electronics/ramps/keypad_v1_0_fully_assembled/
  3206. //
  3207. //#define REPRAPWORLD_KEYPAD
  3208. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // (mm) Distance to move per key-press
  3209.  
  3210. //
  3211. // EasyThreeD ET-4000+ with button input and status LED
  3212. //
  3213. //#define EASYTHREED_UI
  3214.  
  3215. //=============================================================================
  3216. //=============================== Extra Features ==============================
  3217. //=============================================================================
  3218.  
  3219. // @section fans
  3220.  
  3221. // Set number of user-controlled fans. Disable to use all board-defined fans.
  3222. // :[1,2,3,4,5,6,7,8]
  3223. //#define NUM_M106_FANS 1
  3224.  
  3225. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  3226. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  3227. // is too low, you should also increment SOFT_PWM_SCALE.
  3228. //#define FAN_SOFT_PWM
  3229.  
  3230. // Incrementing this by 1 will double the software PWM frequency,
  3231. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  3232. // However, control resolution will be halved for each increment;
  3233. // at zero value, there are 128 effective control positions.
  3234. // :[0,1,2,3,4,5,6,7]
  3235. #define SOFT_PWM_SCALE 0
  3236.  
  3237. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  3238. // be used to mitigate the associated resolution loss. If enabled,
  3239. // some of the PWM cycles are stretched so on average the desired
  3240. // duty cycle is attained.
  3241. //#define SOFT_PWM_DITHER
  3242.  
  3243. // @section extras
  3244.  
  3245. // Support for the BariCUDA Paste Extruder
  3246. //#define BARICUDA
  3247.  
  3248. // @section lights
  3249.  
  3250. // Temperature status LEDs that display the hotend and bed temperature.
  3251. // If all hotends, bed temperature, and target temperature are under 54C
  3252. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  3253. //#define TEMP_STAT_LEDS
  3254.  
  3255. // Support for BlinkM/CyzRgb
  3256. //#define BLINKM
  3257.  
  3258. // Support for PCA9632 PWM LED driver
  3259. //#define PCA9632
  3260.  
  3261. // Support for PCA9533 PWM LED driver
  3262. //#define PCA9533
  3263.  
  3264. /**
  3265. * RGB LED / LED Strip Control
  3266. *
  3267. * Enable support for an RGB LED connected to 5V digital pins, or
  3268. * an RGB Strip connected to MOSFETs controlled by digital pins.
  3269. *
  3270. * Adds the M150 command to set the LED (or LED strip) color.
  3271. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  3272. * luminance values can be set from 0 to 255.
  3273. * For NeoPixel LED an overall brightness parameter is also available.
  3274. *
  3275. * === CAUTION ===
  3276. * LED Strips require a MOSFET Chip between PWM lines and LEDs,
  3277. * as the Arduino cannot handle the current the LEDs will require.
  3278. * Failure to follow this precaution can destroy your Arduino!
  3279. *
  3280. * NOTE: A separate 5V power supply is required! The NeoPixel LED needs
  3281. * more current than the Arduino 5V linear regulator can produce.
  3282. *
  3283. * Requires PWM frequency between 50 <> 100Hz (Check HAL or variant)
  3284. * Use FAST_PWM_FAN, if possible, to reduce fan noise.
  3285. */
  3286.  
  3287. // LED Type. Enable only one of the following two options:
  3288. //#define RGB_LED
  3289. //#define RGBW_LED
  3290.  
  3291. #if EITHER(RGB_LED, RGBW_LED)
  3292. //#define RGB_LED_R_PIN 34
  3293. //#define RGB_LED_G_PIN 43
  3294. //#define RGB_LED_B_PIN 35
  3295. //#define RGB_LED_W_PIN -1
  3296. //#define RGB_STARTUP_TEST // For PWM pins, fade between all colors
  3297. #if ENABLED(RGB_STARTUP_TEST)
  3298. #define RGB_STARTUP_TEST_INNER_MS 10 // (ms) Reduce or increase fading speed
  3299. #endif
  3300. #endif
  3301.  
  3302. // Support for Adafruit NeoPixel LED driver
  3303. #define NEOPIXEL_LED //EC
  3304. #if ENABLED(NEOPIXEL_LED)
  3305. #define NEOPIXEL_TYPE NEO_RGB // NEO_GRBW, NEO_RGBW, NEO_GRB, NEO_RBG, etc. //EC
  3306. // See https://github.com/adafruit/Adafruit_NeoPixel/blob/master/Adafruit_NeoPixel.h
  3307. //#define NEOPIXEL_PIN 4 // LED driving pin
  3308. //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
  3309. //#define NEOPIXEL2_PIN 5
  3310. #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip. (Longest strip when NEOPIXEL2_SEPARATE is disabled.)
  3311. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  3312. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
  3313. //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
  3314.  
  3315. // Support for second Adafruit NeoPixel LED driver controlled with M150 S1 ...
  3316. //#define NEOPIXEL2_SEPARATE
  3317. #if ENABLED(NEOPIXEL2_SEPARATE)
  3318. #define NEOPIXEL2_PIXELS 15 // Number of LEDs in the second strip
  3319. #define NEOPIXEL2_BRIGHTNESS 127 // Initial brightness (0-255)
  3320. #define NEOPIXEL2_STARTUP_TEST // Cycle through colors at startup
  3321. #define NEOPIXEL_M150_DEFAULT -1 // Default strip for M150 without 'S'. Use -1 to set all by default.
  3322. #else
  3323. //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel
  3324. #endif
  3325.  
  3326. // Use some of the NeoPixel LEDs for static (background) lighting
  3327. //#define NEOPIXEL_BKGD_INDEX_FIRST 0 // Index of the first background LED
  3328. //#define NEOPIXEL_BKGD_INDEX_LAST 5 // Index of the last background LED
  3329. //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W
  3330. //#define NEOPIXEL_BKGD_ALWAYS_ON // Keep the backlight on when other NeoPixels are off
  3331. #endif
  3332.  
  3333. /**
  3334. * Printer Event LEDs
  3335. *
  3336. * During printing, the LEDs will reflect the printer status:
  3337. *
  3338. * - Gradually change from blue to violet as the heated bed gets to target temp
  3339. * - Gradually change from violet to red as the hotend gets to temperature
  3340. * - Change to white to illuminate work surface
  3341. * - Change to green once print has finished
  3342. * - Turn off after the print has finished and the user has pushed a button
  3343. */
  3344. #if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED)
  3345. #define PRINTER_EVENT_LEDS
  3346. #endif
  3347.  
  3348. // @section servos
  3349.  
  3350. /**
  3351. * Number of servos
  3352. *
  3353. * For some servo-related options NUM_SERVOS will be set automatically.
  3354. * Set this manually if there are extra servos needing manual control.
  3355. * Set to 0 to turn off servo support.
  3356. */
  3357. //#define NUM_SERVOS 3 // Note: Servo index starts with 0 for M280-M282 commands
  3358.  
  3359. // (ms) Delay before the next move will start, to give the servo time to reach its target angle.
  3360. // 300ms is a good value but you can try less delay.
  3361. // If the servo can't reach the requested position, increase it.
  3362. #define SERVO_DELAY { 300 }
  3363.  
  3364. // Only power servos during movement, otherwise leave off to prevent jitter
  3365. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  3366.  
  3367. // Edit servo angles with M281 and save to EEPROM with M500
  3368. //#define EDITABLE_SERVO_ANGLES
  3369.  
  3370. // Disable servo with M282 to reduce power consumption, noise, and heat when not in use
  3371. //#define SERVO_DETACH_GCODE
  3372.  
Add Comment
Please, Sign In to add comment
Public Pastes
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!