API tools faq
paste
Advertisement
Guest User

Minix Neo X8H boot log

a guest
Jun 10th, 2014
3,502
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 66.72 KB | None | 0 0
raw download clone embed print report
  1. EEEE I3000000032940xf1001100 03877500EEEE I400000004294_M8_BL1_10221 D113B323EEEE I3000000032940xbbbb0000 26A22525
  2. no sdio debug board detected
  3. TE : 102605
  4. BT : 20:11:05 May 27 2014
  5. DCDC01 set to 1050, register from 0x0018 to 0x0024, addr:0x0036
  6. DCDC02 set to 1150, register from 0x0018 to 0x002c, addr:0x0037
  7. DCDC03 set to 1500, register from 0x0038 to 0x0048, addr:0x0038
  8. LDO54 set to 1, register from 0x004e to 0x0050, addr:0x004c
  9. LDO08 set to 2, register from 0x0024 to 0x0024, addr:0x004d
  10. LDO08 set to 3, register from 0x0030 to 0x0030, addr:0x004e
  11. LDO22 set to 4, register from 0x004e to 0x004e, addr:0x004f
  12. LDO08 set to 5, register from 0x0024 to 0x0024, addr:0x0050
  13. LDO8c set to 10, register from 0x0028 to 0x0028, addr:0x0056
  14. LDO84 set to 11, register from 0x0000 to 0x0000, addr:0x0057
  15.  
  16. CPU clock is 792MHz
  17.  
  18. Aml log : DDR0 - init pass with
  19. PGSR0 : 0xc0000fff
  20. Aml log : DDR1 - init pass with
  21. PGSR0 : 0xc0000fff
  22.  
  23. DDR check pass!
  24.  
  25. DDR init use : 14899 us
  26.  
  27. HHH
  28. Start load M8 SMP code!
  29. Load M8 SMP code finished!
  30. Boot From SPI
  31. ucl decompress...pass
  32. 0x12345678
  33. Boot from internal device 1st SPI
  34.  
  35. TE : 527166
  36.  
  37. System Started
  38.  
  39.  
  40. U-boot-00001-g473771c-dirty(m8_k200_v1@473771cb) (May 27 2014 - 20:10:59)
  41.  
  42. clr h-ram
  43. DRAM: 2 GiB
  44. relocation Offset is: 6fec8000
  45. show partition table:
  46. part: 0, name : logo, size : 2000000
  47. part: 1, name : recovery, size : 2000000
  48. part: 2, name : misc, size : 2000000
  49. part: 3, name : boot, size : 2000000
  50. part: 4, name : system, size : 40000000
  51. part: 5, name : cache, size : 20000000
  52. part: 6, name : data, size : end
  53. aml_card_type=0x100
  54. MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
  55. [mmc_register] add mmc dev_num=1, port=2, if_type=6
  56. SDIO Port B: 0, SDIO Port C: 1
  57. PMU fault status:
  58. -- CPUPOFF
  59. reg[0x9A] = 0x1d
  60. register usb cfg[0] = 7ff72bd8
  61. register usb cfg[2] = 7ff74d58
  62. NAND: SPI BOOT: boot_device_flag 0
  63. Nand PHY driver Version: 1.01.001.0003 (c) 2013 Amlogic Inc.
  64. amlnf_phy_init : amlnf init flag 0
  65. reset failed
  66. get_chip_type and ret:fffffffe
  67. get_chip_type and ret:fffffffe
  68. chip detect failed and ret:fffffffe
  69. nandphy_init failed and ret=0xfffffff1
  70. get_boot_device_flag: init_ret -1
  71. get_boot_device_flag SPI BOOT:
  72. nand init failed, change the device_boot_flag to 5 : spi+mmc
  73. Emmckey: Access range is illegal!
  74. [mmc_init] SDIO Port C:1, if_type=6, initialized OK!
  75. Not emmc boot, POR_BOOT_VALUE=5
  76. [mmc_get_partition_table] skip cache partition.
  77. mmc read lba=0x0, blocks=0x1
  78. mmc read lba=0x1, blocks=0x1
  79. mmc_read_partition_tbl: mmc read partition OK!
  80. eMMC/TSD partition table have been checked OK!
  81. i=0,register --- emmc_key
  82. SPI BOOT,spi_env_relocate_spec : env_relocate_spec 53
  83. SF: Detected MX25L1605D with page size 256, total 2 MiB
  84.  
  85. SPI NOR Flash have write protect!!!
  86. set_storage_device_flag: store 5
  87. vpu clk_level in dts: 7
  88. set vpu clk: 364300000Hz, readback: 364300000Hz(0x700)
  89. In: serial
  90. Out: serial
  91. Err: serial
  92. Net: Meson_Ethernet
  93. init suspend firmware done. (ret:0)
  94. mode = 6 vic = 4
  95. reboot_mode=charging
  96. efuse version is not selected.
  97. Hit Enter key to stop autoboot -- : 1 tstc enter
  98. tstc enter
  99. tstc enter
  100.  0
  101. exit abortboot: 0
  102. Booting...
  103. not config efuse version
  104. aml_keys: version 0 can not be init 7ff74f44
  105. current storer:emmc_key
  106. don't found keyname,uboot_key_read:1634
  107. Err key(L81):failed to read key [usid], rc=-22, reallen=0
  108. ## ANDROID Format IMAGE
  109. ## Booting kernel from Legacy Image at 12000000 ...
  110. Image Name: Linux-3.10.33
  111. Image Type: ARM Linux Kernel Image (lzo compressed)
  112. Data Size: 7338236 Bytes = 7 MiB
  113. Load Address: 00008000
  114. Entry Point: 00008000
  115. Verifying Checksum ... OK
  116. Ramdisk start addr = 0x12700800, len = 0x94429
  117. Flat device tree start addr = 0x12795000, len = 0x44e6 magic=0xedfe0dd0
  118. Uncompressing Kernel Image ... OK
  119. uboot time: 4386559 us.
  120. EFUSE machid is not set.
  121. Using machid 0xf81 from environment
  122. From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x509d001
  123. Loading Ramdisk to 05008000, end 0509c429 ... OK
  124. Loading Device Tree to 05000000, end 050074e5 ... OK
  125.  
  126. Starting kernel ...
  127.  
  128. [ 0.000000@0] Booting Linux on physical CPU 0x200
  129. [ 0.000000@0] Linux version 3.10.33-gf1c0102-dirty (root@user-desktop) (gcc version 4.7.3 20130205 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.02-01-20130221 - Linaro GCC 2013.02) ) #6 SMP PREEMPT Thu May 29 13:29:05 CST 2014
  130. [ 0.000000@0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
  131. [ 0.000000@0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  132. [ 0.000000@0] Machine: Amlogic Meson8 platform, model: AMLOGIC
  133. [ 0.000000@0] physical memory start address is 0x0
  134. [ 0.000000@0] reserved_end is 199fffff
  135. [ 0.000000@0]
  136. [ 0.000000@0] Total memory is 2048 MiB
  137. [ 0.000000@0] Reserved low memory from 0x6000000 to 0x199fffff, size: 314 MiB
  138. [ 0.000000@0] mesonfb0(low) : 0x06100000 - 0x07900000 ( 24 MiB)
  139. [ 0.000000@0] mesonfb1(low) : 0x07900000 - 0x07a00000 ( 1 MiB)
  140. [ 0.000000@0] deinterlace0(high) : 0x7dd00000 - 0x80000000 ( 35 MiB)
  141. [ 0.000000@0] mesonstream0(low) : 0x07a00000 - 0x09a00000 ( 32 MiB)
  142. [ 0.000000@0] vdec0(low) : 0x09a00000 - 0x19a00000 (256 MiB)
  143. [ 0.000000@0] ppmgr0(high) : 0x7cd00000 - 0x7dd00000 ( 16 MiB)
  144. [ 0.000000@0] cma: CMA: reserved 8 MiB at 2f000000
  145. [ 0.000000@0] cma: Found region@0, memory base 0, size 15 MiB
  146. [ 0.000000@0] cma: CMA: reserved 16 MiB at 2e000000
  147. [ 0.000000@0] Memory policy: ECC disabled, Data cache writealloc
  148. [ 0.000000@0] chip version=27ed
  149. [ 0.000000@0] PERCPU: Embedded 8 pages/cpu @c1adf000 s8704 r8192 d15872 u32768
  150. [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 425232
  151. [ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200n8 no_console_suspend logo=osd1,loaded,0x15100000,720p,full hdmimode=720p cvbsmode=576cvbs androidboot.firstboot=0 hdmitx=
  152. [ 0.000000@0] osd1:1
  153. [ 0.000000@0] loaded:268435459
  154. [ 0.000000@0] logo has been loaded
  155. [ 0.000000@0] 720p:6
  156. [ 0.000000@0] full:2
  157. [ 0.000000@0] kernel get hdmimode form uboot is 720p
  158. [ 0.000000@0] kernel get cvbsmode form uboot is 576cvbs
  159. [ 0.000000@0] PID hash table entries: 2048 (order: 1, 8192 bytes)
  160. [ 0.000000@0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
  161. [ 0.000000@0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
  162. [ 0.000000@0] Memory: 64MB 16MB 1587MB = 1667MB total
  163. [ 0.000000@0] Memory: 1656312k/1656312k available, 50696k reserved, 1266688K highmem
  164. [ 0.000000@0] Virtual kernel memory layout:
  165. [ 0.000000@0] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  166. [ 0.000000@0] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  167. [ 0.000000@0] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
  168. [ 0.000000@0] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
  169. [ 0.000000@0] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  170. [ 0.000000@0] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  171. [ 0.000000@0] .text : 0xc0008000 - 0xc09669f0 (9595 kB)
  172. [ 0.000000@0] .init : 0xc0967000 - 0xc099e200 ( 221 kB)
  173. [ 0.000000@0] .data : 0xc09a0000 - 0xc0a28380 ( 545 kB)
  174. [ 0.000000@0] .bss : 0xc0a28380 - 0xc0b2caac (1042 kB)
  175. [ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  176. [ 0.000000@0] Preemptible hierarchical RCU implementation.
  177. [ 0.000000@0] NR_IRQS:256
  178. [ 0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
  179. [ 0.000000@0] Global timer: MESON TIMER-F (c09be1c0) initialized
  180. [ 0.000000@0] Switching to timer-based delay loop
  181. [ 0.000000@0] Console: colour dummy device 80x30
  182. [ 0.000000@0] console [ttyS0] enabled
  183. [ 0.316892@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
  184. [ 0.327182@0] pid_max: default: 32768 minimum: 301
  185. [ 0.332092@0] Security Framework initialized
  186. [ 0.336204@0] SELinux: Initializing.
  187. [ 0.339944@0] Mount-cache hash table entries: 512
  188. [ 0.348342@0] CPU: Testing write buffer coherency: ok
  189. [ 0.349892@0] CPU0: thread -1, cpu 0, socket 2, mpidr 80000200
  190. [ 0.355456@0] Setting up static identity map for 0xc06aeed0 - 0xc06aef28
  191. [ 0.362186@0] L310 cache controller enabled
  192. [ 0.366188@0] l2x0: 8 ways, 4096 sets, CACHE_ID 0x4100a0c9, Cache size: 1048576 B
  193. [ 0.373765@0] AUX_CTRL 0x7ec80001, PERFETCH_CTRL 0x71000007, POWER_CTRL 0x00000000
  194. [ 0.381882@0] TAG_LATENCY 0x00000111, DATA_LATENCY 0x00000222
  195. [ 0.440177@0] write pen_release: 1
  196. [ 0.440380@1] CPU1: Booted secondary processor
  197. [ 0.440395@1] CPU1: thread -1, cpu 1, socket 2, mpidr 80000201
  198. [ 0.460170@0] write pen_release: 2
  199. [ 0.468333@2] CPU2: Booted secondary processor
  200. [ 0.468347@2] CPU2: thread -1, cpu 2, socket 2, mpidr 80000202
  201. [ 0.480178@0] write pen_release: 3
  202. [ 0.488341@3] CPU3: Booted secondary processor
  203. [ 0.488354@3] CPU3: thread -1, cpu 3, socket 2, mpidr 80000203
  204. [ 0.488446@0] Brought up 4 CPUs
  205. [ 0.501536@0] SMP: Total of 4 processors activated (8.00 BogoMIPS).
  206. [ 0.507762@0] CPU: All CPU(s) started in SVC mode.
  207. [ 0.513253@0] devtmpfs: initialized
  208. [ 0.522104@0] clkrate [ xtal ] : 24000000
  209. [ 0.522142@0] clkrate [ pll_sys ] : 792000000
  210. [ 0.524986@0] clkrate [ pll_fixed ] : 2550000000
  211. [ 0.529666@0] clkrate [ pll_vid ] : 732000000
  212. [ 0.534097@0] TODO: clk_get_rate_hpll() is not implement in M8 now
  213. [ 0.540247@0] clkrate [ pll_hpll ] : 0
  214. [ 0.544054@0] clkrate [ pll_ddr ] : 0
  215. [ 0.547783@0] clkrate [ a9_clk ] : 792000000
  216. [ 0.552125@0] clkrate [ clk81 ] : 141666666
  217. [ 0.556683@0] pinctrl core: initialized pinctrl subsystem
  218. [ 0.561976@0] regulator-dummy: no parameters
  219. [ 0.567042@0] NET: Registered protocol family 16
  220. [ 0.578608@0] DMA: preallocated 4096 KiB pool for atomic coherent allocations
  221. [ 0.581208@0] VPU driver version: v03
  222. [ 0.583748@0] load vpu_clk in dts: 364300000Hz(7)
  223. [ 0.588441@0] vpu_probe OK
  224. [ 0.591419@0] cma: Assigned CMA region with name cma_0 to amvenc_avc.0 device
  225. [ 0.600399@0] amlogic_gpio gpio: Probed amlogic GPIO driver
  226. [ 0.604020@0] register lm device lm-root
  227. [ 0.607715@0] register lm device lm1
  228. [ 0.611276@0] register lm device lm0
  229. [ 0.614939@0] Init pinux probe!
  230. [ 0.618368@0] pinmux-m8 pinmux: Probed amlogic pinctrl driver
  231. [ 0.623656@0] tv_init_module
  232. [ 0.626486@0] major number 254 for disp
  233.  
  234. [ 0.630389@0] vout_register_server
  235. [ 0.633761@0] register tv module server ok
  236.  
  237. [ 0.638028@0] major number 0 for disp
  238.  
  239. [ 0.641744@0] register tv module server ok
  240.  
  241. [ 0.646016@0] /Work/s802/s8_44_0328/common/drivers/amlogic/i2c/aml_i2c.c : aml_i2c_init
  242. [ 0.654009@0] /Work/s802/s8_44_0328/common/drivers/amlogic/i2c/aml_i2c.c : aml_i2c_probe
  243. [ 0.662032@0] plat->state_name:default
  244. [ 0.665754@0] master_no = 0, maseter_regs=fe600500
  245. [ 0.670639@0] aml-i2c i2c-AO: add adapter aml_i2c_adap0(ed811888)
  246. [ 0.676586@0] aml-i2c i2c-AO: aml i2c bus driver.
  247. [ 0.681312@0] /Work/s802/s8_44_0328/common/drivers/amlogic/i2c/aml_i2c.c : aml_i2c_probe
  248. [ 0.689328@0] plat->state_name:default
  249. [ 0.693068@0] master_no = 1, maseter_regs=fe108500
  250. [ 0.697826@0] set i2c pinmux error
  251. [ 0.701263@0] aml-i2c i2c-A: add adapter aml_i2c_adap1(ed812088)
  252. [ 0.707184@0] aml-i2c i2c-A: aml i2c bus driver.
  253. [ 0.711831@0] /Work/s802/s8_44_0328/common/drivers/amlogic/i2c/aml_i2c.c : aml_i2c_probe
  254. [ 0.719840@0] plat->state_name:default
  255. [ 0.723580@0] master_no = 2, maseter_regs=fe1087c0
  256. [ 0.728418@0] aml-i2c i2c-B: add adapter aml_i2c_adap2(ed812888)
  257. [ 0.734326@0] aml-i2c i2c-B: aml i2c bus driver.
  258. [ 0.738945@0] /Work/s802/s8_44_0328/common/drivers/amlogic/i2c/aml_i2c.c : aml_i2c_probe
  259. [ 0.746980@0] plat->state_name:default
  260. [ 0.750709@0] master_no = 3, maseter_regs=fe1087e0
  261. [ 0.755468@0] set i2c pinmux error
  262. [ 0.758905@0] aml-i2c i2c-C: add adapter aml_i2c_adap3(ed813088)
  263. [ 0.764837@0] aml-i2c i2c-C: aml i2c bus driver.
  264. [ 0.769456@0] /Work/s802/s8_44_0328/common/drivers/amlogic/i2c/aml_i2c.c : aml_i2c_probe
  265. [ 0.777491@0] plat->state_name:default
  266. [ 0.781220@0] master_no = 4, maseter_regs=fe108d20
  267. [ 0.786058@0] aml-i2c i2c-D: add adapter aml_i2c_adap4(ed813888)
  268. [ 0.791969@0] aml-i2c i2c-D: aml i2c bus driver.
  269. [ 0.796633@0] aml_pmu_init, 454
  270. [ 0.799701@0] call aml_dvfs_init in
  271. [ 0.803196@0] [DVFS]aml_dvfs_probe, child name:vcck_dvfs
  272. [ 0.808430@0] [DVFS]dvfs table of vcck_dvfs is:
  273. [ 0.812943@0] [DVFS] freq, min_uV, max_uV
  274. [ 0.817789@0] [DVFS] 96000, 825000, 825000
  275. [ 0.822650@0] [DVFS] 192000, 825000, 825000
  276. [ 0.827497@0] [DVFS] 312000, 825000, 825000
  277. [ 0.832357@0] [DVFS] 408000, 825000, 825000
  278. [ 0.837205@0] [DVFS] 504000, 825000, 825000
  279. [ 0.842065@0] [DVFS] 600000, 850000, 850000
  280. [ 0.846914@0] [DVFS] 720000, 850000, 850000
  281. [ 0.851774@0] [DVFS] 816000, 875000, 875000
  282. [ 0.856622@0] [DVFS] 1008000, 925000, 925000
  283. [ 0.861482@0] [DVFS] 1200000, 975000, 975000
  284. [ 0.866331@0] [DVFS] 1416000, 1025000, 1025000
  285. [ 0.871191@0] [DVFS] 1608000, 1100000, 1100000
  286. [ 0.876039@0] [DVFS] 1800000, 1125000, 1125000
  287. [ 0.880899@0] [DVFS] 1992000, 1150000, 1150000
  288. [ 0.885815@0] hdmitx: system: amhdmitx_init
  289. [ 0.889908@0] hdmitx: system: Ver: 2014Jan5a
  290. [ 0.894231@0] hdmitx: system: amhdmitx_probe
  291. [ 0.898702@0] hdmitx: system: ALREADY init VIC = 4
  292. [ 0.903640@1] hdmitx: system: reset intr mask
  293. [ 0.920423@0] hdmitx: system: irq 1
  294. [ 0.937006@0] bio: create slab <bio-0> at 0
  295. [ 0.937566@0] SCSI subsystem initialized
  296. [ 0.939606@0] usbcore: registered new interface driver usbfs
  297. [ 0.945145@0] usbcore: registered new interface driver hub
  298. [ 0.950621@0] usbcore: registered new device driver usb
  299. [ 0.955813@0] Linux video capture interface: v2.00
  300. [ 0.960654@0] LCD driver init
  301. [ 0.963638@0] switch_vpu_mem_pd: vencp ON
  302. [ 0.967452@0] request vpu clk holdings: vencp 106250000Hz
  303. [ 0.972842@0] TV mode 720p selected.
  304. [ 0.976379@0] already display in uboot
  305. [ 0.982874@0] call aml_pmu_probe_init in
  306. [ 0.984068@0] aml_pmus_probe, child name:rn5t618
  307. [ 0.988602@0] aml_pmus_probe, i2c_bus:i2c_bus_ao
  308. [ 0.993512@0] [RICOH]setup_supply_data, failed to get property: board_battery
  309. [ 1.000318@0] [DVFS]aml_dvfs_register_driver, driver rn5t618-dvfs regist success, mask:7, source id:1
  310. [ 1.009554@0] [RN5T618]ricoh_pmu_probe, 296
  311. [ 1.013666@0] Allocate new i2c device: adapter:0, addr:0x32, node name:rn5t618, type:ricoh_pmu
  312. [ 1.022241@0] aml_pmus_probe, child name:minix-mcu
  313. [ 1.027006@0] aml_pmus_probe, i2c_bus:i2c_bus_b
  314. [ 1.031518@0] aml_pmus_probe, device minix-mcu status is disable, stop probe it
  315. [ 1.038790@0] aml_pmus_probe, child name:rtc8563
  316. [ 1.043395@0] aml_pmus_probe, i2c_bus:i2c_bus_ao
  317. [ 1.048043@0] Allocate new i2c device: adapter:0, addr:0x51, node name:rtc8563, type:rtc8563
  318. [ 1.056503@0] Advanced Linux Sound Architecture Driver Initialized.
  319. [ 1.062998@0] Bluetooth: Core ver 2.16
  320. [ 1.066385@0] NET: Registered protocol family 31
  321. [ 1.070964@0] Bluetooth: HCI device and connection manager initialized
  322. [ 1.077463@0] Bluetooth: HCI socket layer initialized
  323. [ 1.082491@0] Bluetooth: L2CAP socket layer initialized
  324. [ 1.087698@0] Bluetooth: SCO socket layer initialized
  325. [ 1.092932@0] cfg80211: Calling CRDA to update world regulatory domain
  326. [ 1.100419@0] Switching to clocksource Timer-E
  327. [ 1.110366@0] NET: Registered protocol family 2
  328. [ 1.110880@0] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
  329. [ 1.116544@0] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
  330. [ 1.123117@0] TCP: Hash tables configured (established 4096 bind 4096)
  331. [ 1.129596@0] TCP: reno registered
  332. [ 1.132929@0] UDP hash table entries: 256 (order: 1, 8192 bytes)
  333. [ 1.138932@0] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  334. [ 1.145532@0] NET: Registered protocol family 1
  335. [ 1.149901@0] wifi_dev_probe
  336. [ 1.152690@0] wifi_dt : interrupt_pin=GPIOX_21
  337. [ 1.157134@0] wifi_dt : irq_num=null
  338. [ 1.160663@0] wifi_dt : irq_trigger_type=GPIO_IRQ_HIGH
  339. [ 1.165788@0] wifi_dt : power_on_pin=GPIOX_11
  340. [ 1.170113@0] wifi_dev_probe : there is no wifi_power_gpio2 setup in DTS file!
  341. [ 1.177318@0] wifi_dt : clock_32k_pin=GPIOX_10
  342. [ 1.181730@0] interrupt_pin=133, irq_num=4, irq_trigger_type=0, power_on_pin=123,clock_32k_pin=122
  343. [ 1.190915@0] Unpacking initramfs...
  344. [ 1.231856@0] Freeing initrd memory: 592K (c5008000 - c509c000)
  345. [ 1.233072@0] audit: initializing netlink socket (disabled)
  346. [ 1.234049@1] hdmitx: edid: edid ready
  347. [ 1.241491@0] type=2000 audit(1.160:1): initialized
  348. [ 1.246825@0] bounce pool size: 64 pages
  349. [ 1.254252@0] VFS: Disk quotas dquot_6.5.2
  350. [ 1.254504@0] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  351. [ 1.263101@0] fuse init (API version 7.22)
  352. [ 1.265509@0] msgmni has been set to 810
  353. [ 1.270319@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
  354. [ 1.276461@0] io scheduler noop registered
  355. [ 1.280509@0] io scheduler deadline registered
  356. [ 1.285078@0] io scheduler cfq registered (default)
  357. [ 1.334986@0] loop: module loaded
  358. [ 1.335708@0] tun: Universal TUN/TAP device driver, 1.6
  359. [ 1.337869@0] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  360. [ 1.344347@0] PPP generic driver version 2.4.2
  361. [ 1.348745@0] PPP BSD Compression module registered
  362. [ 1.353472@0] PPP Deflate Compression module registered
  363. [ 1.358702@0] PPP MPPE Compression module registered
  364. [ 1.363615@0] NET: Registered protocol family 24
  365. [ 1.368267@0] usbcore: registered new interface driver asix
  366. [ 1.373838@0] usbcore: registered new interface driver ax88179_178a
  367. [ 1.380026@0] usbcore: registered new interface driver cdc_ether
  368. [ 1.386019@0] usbcore: registered new interface driver dm9601
  369. [ 1.391740@0] usbcore: registered new interface driver net1080
  370. [ 1.397549@0] usbcore: registered new interface driver cdc_subset
  371. [ 1.403602@0] usbcore: registered new interface driver zaurus
  372. [ 1.409368@0] usbcore: registered new interface driver cdc_ncm
  373. [ 1.415337@0] usbcore: registered new interface driver cdc_acm
  374. [ 1.420911@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  375. [ 1.429139@0] usbcore: registered new interface driver usb-storage
  376. [ 1.435305@0] usbcore: registered new interface driver usbserial
  377. [ 1.441228@0] usbcore: registered new interface driver option
  378. [ 1.444031@1] hdmitx: edid: edid ready
  379. [ 1.444039@1] hdmitx: edid: check sum valid
  380. [ 1.444044@1] hdmitx: edid: blk0 raw data
  381. [ 1.444077@1] 00ffffffffffff0004729c008825208534120103802c19782eee95a3544c9926
  382. [ 1.444106@1] 0f5054b30c00d1c0714f810081809500010101010101023a801871382d40582c
  383. [ 1.444135@1] 4500bbf91000001c000000fd00374b1e5010000a202020202020000000fc0058
  384. [ 1.444164@1] 323333480a20202020202020000000ff004c464e30423030363339313020003c
  385. [ 1.444165@1]
  386. [ 1.444197@1] hdmitx: edid: HDMI: set default vic
  387. [ 1.444201@1] hdmitx: edid: edid blk0 checksum:0 ext_flag:0
  388. [ 1.444209@1] hdmitx: video: get current mode: 720p
  389. [ 1.444220@1] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 4
  390. [ 1.444223@1] hdmitx: audio: audio channel num is 0
  391. [ 1.444229@1] hdmitx: audio: SPDIF
  392. [ 1.444241@1] hdmitx: audio: current VIC: 4
  393. [ 1.444243@1] hdmitx: audio: audio sample rate: 0
  394. [ 1.444245@1] hdmitx: audio: reset audio N para
  395. [ 1.444254@1] hdmitx: audio: PCM out to HDMI
  396. [ 1.467174@1] hdmitx: audio: Time out: AIU_HDMI_CLK_DATA_CTRL
  397. [ 1.467176@1] hdmitx: audio: i2s_to_spdif_flag:1
  398. [ 1.467178@1] hdmitx: audio: Enable audio spdif to HDMI
  399. [ 1.467236@1] hdmitx: cec: CEC not ready
  400. [ 1.556264@0] usbserial: USB Serial support registered for GSM modem (1-port)
  401. [ 1.563581@0] mousedev: PS/2 mouse device common for all mice
  402. [ 1.569388@0] i2c /dev entries driver
  403. [ 1.573262@0] usbcore: registered new interface driver uvcvideo
  404. [ 1.578600@0] USB Video Class driver (1.1.1)
  405. [ 1.583085@0] device-mapper: uevent: version 1.0.3
  406. [ 1.587871@0] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
  407. [ 1.596327@0] Bluetooth: HCI UART driver ver 2.2
  408. [ 1.600777@0] Bluetooth: HCI H4 protocol initialized
  409. [ 1.606307@0] usbcore: registered new interface driver usbhid
  410. [ 1.611438@0] usbhid: USB HID core driver
  411. [ 1.615872@0] zram: Created 1 device(s) ...
  412. [ 1.619967@0] ashmem: initialized
  413. [ 1.623028@0] logger: created 256K log 'log_main'
  414. [ 1.627710@0] logger: created 256K log 'log_events'
  415. [ 1.632553@0] logger: created 256K log 'log_radio'
  416. [ 1.637333@0] logger: created 256K log 'log_system'
  417. [ 1.642151@0] vout_init_module
  418. [ 1.645134@0] start init vout module
  419.  
  420. [ 1.648828@0] create vout attribute ok
  421.  
  422. [ 1.652894@0] lcd_extern_init
  423. [ 1.655877@0] ge2d_init
  424. [ 1.658170@0] ge2d_dev major:248
  425.  
  426. [ 1.661594@0] ge2d start monitor
  427.  
  428. [ 1.664821@0] osd_init
  429. [ 1.664829@1] ge2d workqueue monitor start
  430.  
  431. [ 1.671543@0] Frame buffer memory assigned at phy:0x06100000, vir:0xf1000000, size=24576K
  432. [ 1.679420@0] init fbdev bpp is :32
  433.  
  434. [ 1.682951@0] ---------------clear framebuffer0 memory
  435.  
  436. [ 1.697604@0] Frame buffer memory assigned at phy:0x07900000, vir:0xf0200000, size=1024K
  437. [ 1.700049@0] init fbdev bpp is :24
  438.  
  439. [ 1.706133@0] osd probe ok
  440.  
  441. [ 1.706644@0] osd_ext_init
  442. [ 1.709429@0] vout2_init_module enter
  443. [ 1.713354@0] amlvideo-000: V4L2 device registered as video10
  444. [ 1.718823@0] ionvideo-000: V4L2 device registered as video13
  445. [ 1.724340@0] Video Technology Magazine Ion Video Capture Board ver 1.0 successfully loaded.
  446. [ 1.732990@0] switch_vpu_mem_pd: di_pre OFF
  447. [ 1.737086@0] keys===========================================
  448. [ 1.742618@0] keys_devno=f400000
  449. [ 1.745969@0] securitykey: device aml_keys created
  450. [ 1.750594@0] amlkeys=0
  451. [ 1.753046@0] platform_driver_register--aml_keys_driver--------------------
  452. [ 1.760255@0] set uart_ao pinmux use pinctrl subsystem
  453. [ 1.765095@0] P_AO_RTI_PIN_MUX_REG:5860
  454. [ 1.768890@0] start uart_ao_ttyS0:(irq = 122)
  455. [ 1.773215@0] register uart_ao ok
  456. [ 1.776738@0] set uart_a pinmux use pinctrl subsystem
  457. [ 1.781531@0] P_AO_RTI_PIN_MUX_REG:5860
  458. [ 1.785391@0] start uart_a_ttyS1:(irq = 58)
  459. [ 1.789511@0] register uart_a ok
  460. [ 1.792907@0] start uart_d_ttyS4:(irq = 126)
  461. [ 1.796990@0] register uart_d ok
  462. [ 1.800246@0] dwc_otg: version 3.10a 21-DEC-2012
  463. [ 1.804824@0] dwc_otg_driver_probe NOT match
  464. [ 1.809055@0] usb1: type: 1, speed: 0, config: 0, dma: 0, id: 1, phy: fe108820, ctrl: fe080000
  465. [ 1.817628@0] USB (1) use clock source: XTAL input
  466. [ 2.023265@0] Core Release: 3.10a
  467. [ 2.023297@0] Setting default values for core params
  468. [ 2.425707@0] Using Buffer DMA mode
  469. [ 2.425741@0] OTG VER PARAM: 1, OTG VER FLAG: 1
  470. [ 2.428067@0] Working on port type = HOST
  471. [ 2.433021@0] dwc_otg lm1: DWC OTG Controller
  472. [ 2.436439@0] dwc_otg lm1: new USB bus registered, assigned bus number 1
  473. [ 2.443092@0] dwc_otg lm1: irq 63, io mem 0x00000000
  474. [ 2.448051@0] Init: Port Power? op_state=1
  475. [ 2.452077@0] Init1: Power Port (0)
  476. [ 2.456077@0] hub 1-0:1.0: USB hub found
  477. [ 2.459463@0] hub 1-0:1.0: 1 port detected
  478. [ 2.463827@0] usb0: type: 0, speed: 0, config: 0, dma: 0, id: 0, phy: fe108800, ctrl: fe040000
  479. [ 2.472108@0] USB (0) use clock source: XTAL input
  480. [ 2.653711@1] Indeed it is in host mode hprt0 = 00021501
  481. [ 2.677812@0] Core Release: 3.10a
  482. [ 2.677850@0] Setting default values for core params
  483. [ 2.833689@1] usb 1-1: new high-speed USB device number 2 using dwc_otg
  484. [ 2.834904@1] Indeed it is in host mode hprt0 = 00001101
  485. [ 3.035613@1] hub 1-1:1.0: USB hub found
  486. [ 3.035956@1] hub 1-1:1.0: 4 ports detected
  487. [ 3.080225@0] Using Buffer DMA mode
  488. [ 3.080260@0] OTG VER PARAM: 1, OTG VER FLAG: 1
  489. [ 3.082585@0] Working on port type = OTG
  490. [ 3.086508@0] Current port type: SLAVE
  491. [ 3.090386@0] dwc_otg lm0: DWC OTG Controller
  492. [ 3.094592@0] dwc_otg lm0: new USB bus registered, assigned bus number 2
  493. [ 3.101241@0] dwc_otg lm0: irq 62, io mem 0x00000000
  494. [ 3.106627@0] hub 2-0:1.0: USB hub found
  495. [ 3.110078@0] hub 2-0:1.0: 1 port detected
  496. [ 3.114355@0] Dedicated Tx FIFOs mode
  497. [ 3.118090@0] using timer detect id change, ed064000
  498. [ 3.122977@0] ethernet_driver probe!
  499. [ 3.126312@0] Please config savepowermode.
  500. [ 3.130346@0] Please config reset_pin_enable.
  501. [ 3.134706@0] Please config reset_delay.
  502. [ 3.138581@0] Please config reset_pin.
  503. [ 3.142314@0] ethernetinit(dbg[c09e44a4]=1)
  504. [ 3.146543@0] ethernet base addr is fe0c0000
  505. [ 3.150761@0] write mac add to:ed084948: 46 44 13 51 30 90 |FDQ0.|
  506. [ 3.159653@0] libphy: AMLMAC MII Bus: probed
  507. [ 3.161214@0] eth0: PHY ID 0007c0f1 at 0 IRQ -1 (0:00) active
  508. [ 3.167077@0] Amlogic A/V streaming port init
  509. [ 3.172490@0] init vdec memsource 161480704->429916159
  510. [ 3.176561@0] regist mpeg12 codec profile
  511. [ 3.180420@0] regist mpeg4 codec profile
  512. [ 3.184297@0] amvdec_vc1 module init
  513. [ 3.187870@0] regist vc1 codec profile
  514. [ 3.191554@0] amvdec_h264 module init
  515. [ 3.195270@0] regist h264 codec profile
  516. [ 3.199008@0] amvdec_h264_4k2k module init
  517. [ 3.203124@0] regist h264_4k2k codec profile
  518. [ 3.207411@0] regist mjpeg codec profile
  519. [ 3.211226@0] amvdec_real module init
  520. [ 3.214968@0] regist real codec profile
  521. [ 3.218973@0] regist avc codec profile
  522. [ 3.222409@0] jpegenc module init
  523. [ 3.226500@0] efuse===========================================
  524. [ 3.231630@0] efuse: device efuse created
  525. [ 3.235602@0] efuse--------------------------------------------
  526. [ 3.241417@0] SARADC Driver init.
  527. [ 3.244831@0] __saradc_probe__
  528. [ 3.393792@1] saradc calibration: ref_val = 506
  529. [ 3.393832@1] saradc calibration: ref_nominal = 512
  530. [ 3.397538@1] saradc calibration: coef = 4080
  531. [ 3.402121@1] ir irblaster probe
  532. [ 3.405239@1] Remote Driver
  533. [ 3.407931@1] Remote platform_data g_remote_base=fe600580
  534. [ 3.413255@1] set drvdata completed
  535.  
  536. [ 3.416801@1] device_create_file completed
  537.  
  538. [ 3.421466@1] input: aml_keypad as /devices/platform/meson-remote/input/input0
  539. [ 3.428488@1] input_register_device completed
  540.  
  541. [ 3.432791@1] [0x0] = 0x1dd0190
  542. [ 3.435868@1] [0x4] = 0xf800ca
  543. [ 3.438886@1] [0x8] = 0x82006e
  544. [ 3.441920@1] [0xc] = 0x3c0030
  545. [ 3.444963@1] [0x10] = 0x30fa0013
  546. [ 3.448248@1] [0x18] = 0x6f19000
  547. [ 3.451455@1] [0x1c] = 0x9f40
  548. [ 3.454410@1] [0x20] = 0x0
  549. [ 3.457089@1] [0x24] = 0x0
  550. [ 3.459776@1] [0x28] = 0x0
  551. [ 3.462464@1] set_remote_mode[48]
  552. [ 3.465783@1] remote config major:238
  553.  
  554. [ 3.469593@1] physical address:0x2d0e6000
  555. [ 3.473513@1] ADC Keypad Driver init.
  556. [ 3.477233@1] ==touch_ts_init==
  557. [ 3.480325@1] ==ft5x0x_ts_init==
  558. [ 3.483473@1] ==goodix_ts_init==
  559. [ 3.486685@1] ==gsl_ts_init==
  560. [ 3.489619@1] i2c-core: driver [gslx680_compatible] using legacy suspend method
  561. [ 3.496887@1] i2c-core: driver [gslx680_compatible] using legacy resume method
  562. [ 3.504109@1] !!!ntp_ts: ret = 0.
  563. [ 3.507452@1] VTL ct36x TouchScreen driver, <george.chen@vtl.com.cn>.
  564. [ 3.513899@1] i2c-core: driver [ct36x] using legacy suspend method
  565. [ 3.520021@1] i2c-core: driver [ct36x] using legacy resume method
  566. [ 3.526099@1] VTL ct36x TouchScreen driver End.
  567. [ 3.530760@1] i2c-core: driver [lis3dh_acc] using legacy suspend method
  568. [ 3.537208@1] i2c-core: driver [lis3dh_acc] using legacy resume method
  569. [ 3.543753@1] i2c-core: driver [bma222] using legacy suspend method
  570. [ 3.549926@1] i2c-core: driver [bma222] using legacy resume method
  571. [ 3.556140@1] i2c-core: driver [dmard06] using legacy suspend method
  572. [ 3.562408@1] i2c-core: driver [dmard06] using legacy resume method
  573. [ 3.568731@1] i2c-core: driver [dmard10] using legacy suspend method
  574. [ 3.574987@1] i2c-core: driver [dmard10] using legacy resume method
  575. [ 3.581248@1] stk831x_init
  576. [ 3.583941@1] mxc622x accelerometer driver: init
  577. [ 3.588527@1] i2c-core: driver [mxc622x] using legacy suspend method
  578. [ 3.594837@1] i2c-core: driver [mxc622x] using legacy resume method
  579. [ 3.601149@1] i2c-core: driver [elan_epl6814] using legacy suspend method
  580. [ 3.607840@1] i2c-core: driver [elan_epl6814] using legacy resume method
  581. [ 3.614540@1] i2c-core: driver [LTR501] using legacy suspend method
  582. [ 3.620746@1] i2c-core: driver [LTR501] using legacy resume method
  583. [ 3.626986@1] GPIO Keypad Driver init.
  584. [ 3.630705@1] ==gpio_key_probe==
  585. [ 3.633871@1] reg:2620,clearmask=400040,setmask=1
  586. [ 3.638604@1] reg:2622,clearmask=ff0000,set pin=3
  587. [ 3.643284@1] reg:2623,clearmask=7000000,setmask=7
  588. [ 3.648074@1] reg:2620,clearmask=800080,setmask=10001
  589. [ 3.653166@1] reg:2622,clearmask=ff000000,set pin=3
  590. [ 3.658020@1] reg:2623,clearmask=70000000,setmask=7
  591. [ 3.662910@1] power key(116) registed.
  592. [ 3.662917@0] key 116 up
  593. [ 3.669268@1] input: gpio_keypad as /devices/platform/gpio_keypad.5/input/input1
  594. [ 3.676605@1] gpio keypad register input device completed.
  595.  
  596. [ 3.682034@1] gpio keypad major:237
  597.  
  598. [ 3.685755@1] spi_nor_init
  599. [ 3.688352@1] amlogic_spi_nor_probe:
  600. [ 3.691829@1] amlogic_spi->state_name:default
  601. [ 3.696230@1] AMLOGIC_SPI_NOR cc000000.spi: master is unqueued, this is deprecated
  602. [ 3.703782@1] spi_nor_probe
  603. [ 3.706476@1] check_storage_device : spi boot_device_flag : 0
  604. [ 3.712276@1] spi_nor apollospi:32766: mx25l160 (2048 Kbytes)
  605. [ 3.718106@1] Creating 2 MTD partitions on "apollospi:32766":
  606. [ 3.723643@1] 0x000000000000-0x000000060000 : "bootloader"
  607. [ 3.729844@1] 0x000000100000-0x000000110000 : "ubootenv"
  608. [ 3.735053@1] amlogic_spi_nor_probe over
  609. [ 3.738409@1] mmc driver version: 1.05, 2014-01-16: sdhc eMMC run at 8bit@50MHz ok
  610. [ 3.746371@1] host->base fe108c20
  611. [ 3.749161@1] pdata->caps 7
  612. [ 3.751897@1] pdata->caps2 0
  613. [ 3.754797@1] get property: port, value:0x00000001
  614. [ 3.761259@1] get property: ocr_avail, value:0x00200000
  615. [ 3.767771@1] get property: f_min, value:0x000493e0
  616. [ 3.774271@1] get property: f_max, value:0x02faf080
  617. [ 3.780763@1] get property: max_req_size, value:0x00020000
  618. [ 3.787273@1] get property: irq_in, value:0x00000003
  619. [ 3.793774@1] get property: irq_out, value:0x00000005
  620. [ 3.800270@1] get property: gpio_cd, str:CARD_6
  621. [ 3.806257@1] get property: gpio_ro, str:GPIOZ_0
  622. [ 3.812315@1] get property: pinname, str:sd
  623. [ 3.817958@1] get property: jtag_pin, str:CARD_0
  624. [ 3.823940@1] get property: card_type, value:0x00000005
  625. [ 3.830432@1] get property: gpio_dat3, str:CARD_4
  626. [ 3.873706@1] reg:2620,clearmask=80008,setmask=10001
  627. [ 3.873759@1] reg:2621,clearmask=ff000000,set pin=64
  628. [ 3.878060@1] reg:2623,clearmask=7000,setmask=7
  629. [ 3.882569@1] reg:2620,clearmask=200020,setmask=1
  630. [ 3.887335@1] reg:2622,clearmask=ff00,set pin=64
  631. [ 3.891929@1] reg:2623,clearmask=700000,setmask=7
  632. [ 3.903737@2] pdata->caps 107
  633. [ 3.903772@2] pdata->caps2 0
  634. [ 3.903932@2] get property: port, value:0x00000002
  635. [ 3.910432@2] get property: ocr_avail, value:0x00200000
  636. [ 3.916948@2] get property: f_min, value:0x000493e0
  637. [ 3.923435@2] get property: f_max, value:0x02faf080
  638. [ 3.929945@2] get property: f_max_w, value:0x02faf080
  639. [ 3.936445@2] get property: max_req_size, value:0x00020000
  640. [ 3.942943@2] get property: pinname, str:emmc
  641. [ 3.948755@2] get property: card_type, value:0x00000001
  642. [ 3.955257@2] get property: gpio_dat3, str:BOOT_3
  643. [ 3.961229@2] [is_emmc_exist] host->storage_flag=0, POR_BOOT_VALUE=5
  644. [ 4.003753@2] pdata->caps 107
  645. [ 4.003787@2] pdata->caps2 0
  646. [ 4.003947@2] get property: port, value:0x00000000
  647. [ 4.010448@2] get property: ocr_avail, value:0x00200000
  648. [ 4.016962@2] get property: f_min, value:0x000493e0
  649. [ 4.023450@2] get property: f_max, value:0x02faf080
  650. [ 4.029961@2] get property: max_req_size, value:0x00020000
  651. [ 4.036464@2] get property: pinname, str:sdio
  652. [ 4.042261@2] get property: card_type, value:0x00000003
  653. [ 4.084991@2] [aml_sdio_probe] aml_sdio_probe() success!
  654. [ 4.087380@2] [dsp]DSP start addr 0xc6000000
  655. [ 4.090216@2] [dsp]register dsp to char divece(232)
  656. [ 4.096119@2] aml_rtc_init...
  657. [ 4.100377@2] reg:2620,clearmask=10001,setmask=10001
  658. [ 4.101742@2] reg:2621,clearmask=ff,set pin=107
  659. [ 4.106249@2] reg:2623,clearmask=7,setmask=7
  660. [ 4.113621@2] rtc_hym8563 0-0051: rtc core: registered rtc8563 as rtc0
  661. [ 4.117183@2] [AML1218]call aml1216_battery_init, ret = 0
  662. [ 4.122518@2] [AML1218]call aml1218_battery_init, ret = 0
  663. [ 4.127898@2] [RN5T618]call rn5t618_battery_probe in
  664. [ 4.132769@2] input: rn5t618_pmu as /devices/i2c-0/0-0032/rn5t618_pmu.0/input/input2
  665. [ 4.140624@2] [RN5T618]use BSP configed battery parameters
  666. [ 4.145970@2] [RN5T618] NO BATTERY_PARAMETERS FOUND
  667. [ 4.156635@2] emmc: BKOPS_EN bit is not set
  668. [ 4.157167@2] [RN5T618] DUMP ALL REGISTERS:
  669. [ 4.160615@2] emmc: new high speed MMC card at address 0001, clock 35416666, 4-bit-bus-width
  670. [ 4.168031@2] 0x00 - 0f: 04 0c 10 00 00 00 00 00 00 01 10 03 9f 00 00 00
  671. [ 4.176403@2] 0x10 - 1f: e9 05 00 00 00 0f cc 99 dd 00 00 bf 22 ee dd ee
  672. [ 4.183238@2] 0x20 - 2f: 00 00 00 00 00 ff ff ff 0f 00 cc 00 13 03 13 03
  673. [ 4.190085@2] 0x30 - 3f: 13 03 00 00 00 00 24 2c 48 00 00 18 18 38 00 00
  674. [ 4.196933@2] 0x40 - 4f: 00 00 00 00 1f 30 ff 00 00 00 00 00 50 24 30 4e
  675. [ 4.203772@2] mmcblk0: emmc:0001 MAG2GA 14.5 GiB
  676. [ 4.206795@2] 0x50 - 5f:
  677. [ 4.209117@2] mmcblk0boot0: emmc:0001 MAG2GA partition 1 2.00 MiB
  678. 24 00 00 00
  679. [ 4.216223@2] mmcblk0boot1: emmc:0001 MAG2GA partition 2 2.00 MiB
  680. 00 00 28 00 4e 24 30 4e 24 00 00 00
  681. [ 4.227448@2] 0x60 - 6f: 00 00 00 00 2f 00 28 00 00 00 ff 0f 00 00 00 00
  682. [ 4.234294@2] 0x70 - 7f: 00 00 00 00 00 00 00 00
  683. [ 4.237204@2] mmcblk0: unknown partition table
  684. 00 ff 00 ff
  685. [ 4.242754@2] emmc read lba=0x0, blocks=0x1 OK!
  686. 00 ff 00 ff
  687. [ 4.248384@2] emmc read lba=0x1, blocks=0x1 OK!
  688. [ 4.252874@2] [mmc_read_partition_tbl] mmc read partition OK!
  689. [ 4.260409@2] 0x80 - 8f: 00 ff 00 ff 00 ff 00 ff 00 00 00 00 00 00 00 00
  690. [ 4.264339@3] add_emmc_partition
  691. [ 4.268769@3] [mmcblk0p01] reserved offset 0x000000000000, size 0x000004000000
  692. [ 4.270491@2] 0x90 - 9f: 0a 00 00 00 00 0a 00 00 04 00 00 00 00 00 00 00
  693. [ 4.272292@2] 0xa0 - af: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  694. [ 4.274099@2] 0xb0 - bf: 06 07 00 23 00 21 18 05 02 3b 01 34 01 00 7f ff
  695. [ 4.275908@2] 0xc0 - cf: ff ff 00 e0 02 0c 00 00 02 0c ff 0f ff ff ff ff
  696. [ 4.277715@2] 0xd0 - df: ff 00 00 00 f1 00 55 00 01 00 00 00 00 00 00 00
  697. [ 4.279518@2] 0xe0 - ef: 00 00 08 ca 08 ca 64 ff ff ff ff 00 00 00 00 10
  698. [ 4.281321@2] 0xf0 - ff: 00 00 08 ff ff ff ef 00 00 00 00 3f fe 00 00 00
  699. [ 4.281356@2] [RN5T618]call rn5t618_battery_probe exit, ret:0
  700. [ 4.281357@2] [RN5T618]call rn5t618_battery_init, ret = 0
  701. [ 4.281381@2] vdin_drv_init: major 236
  702. [ 4.281534@2] amvdec_656in module: init.
  703. [ 4.281539@2] amvdec_656in_init_module:major 235
  704. [ 4.281804@2] amvdec_656in probe ok.
  705. [ 4.282067@2] amvdec_csi probe ok.
  706. [ 4.282088@2] [viuin..]viuin_init_module viuin module init
  707. [ 4.282228@2] [viuin..]viuin_probe probe ok.
  708. [ 4.282455@2] [isp..]isp_probe isp probe ok.
  709. [ 4.282475@2] [sii9233a_drv_init] Ver: 2013Nov12
  710. [ 4.373925@2] wifi_power power_gpio is 6
  711. [ 4.374048@3] [mmcblk0p02] cache offset 0x000004800000, size 0x000020000000
  712. [ 4.374180@3] [mmcblk0p03] env offset 0x000025000000, size 0x000000800000
  713. [ 4.374315@3] [mmcblk0p04] logo offset 0x000026000000, size 0x000002000000
  714. [ 4.374442@3] [mmcblk0p05] recovery offset 0x000028800000, size 0x000002000000
  715. [ 4.374572@3] [mmcblk0p06] misc offset 0x00002b000000, size 0x000002000000
  716. [ 4.374696@3] [mmcblk0p07] boot offset 0x00002d800000, size 0x000002000000
  717. [ 4.374820@3] [mmcblk0p08] system offset 0x000030000000, size 0x000040000000
  718. [ 4.374954@3] [mmcblk0p09] data offset 0x000070800000, size 0x000333600000
  719. [ 4.374979@3] card key: card_blk_probe.
  720. [ 4.374984@3] emmc_key_init:421 emmc key lba_start:0x20,lba_end:0x220
  721. [ 4.374989@3] i=0,register --- emmc_key
  722. [ 4.374991@3] emmc key: emmc_key_init:443 ok.
  723. [ 4.375021@3] Exit aml_emmc_partition_ops OK.
  724. [ 4.467992@2] wifi_power power_gpio2 is 123
  725. [ 4.472323@2] amlogic rfkill init
  726. [ 4.475507@3] mmcblk0boot1: unknown partition table
  727. [ 4.475522@2] not get gpio_en
  728. [ 4.475524@2] not get gpio_wake
  729. [ 4.487712@3] mmcblk0boot0: unknown partition table
  730. [ 4.503779@2] wifi_request_32k_clk : OFF-->ON for bt_rfkill
  731. [ 4.503827@2] clock_32k_pin(122) : (null)
  732. [ 4.507707@2] clock_32k_pin(122) : sdio_wifi
  733. [ 4.614747@2] aml_hw_crypto initialization.
  734. [ 4.615428@2] usbcore: registered new interface driver snd-usb-audio
  735. [ 4.619938@2] enter rt5616_modinit
  736. [ 4.623195@2] == ES8323 == es8323_modinit()
  737. [ 4.627835@2] [aml-spdif-dai]enter aml_dai_spdif_init
  738. [ 4.632425@2] [aml-spdif-dai]aml_spdif_probe
  739. [ 4.636839@2] test codec es8323
  740. [ 4.640242@2] using external codec, index = 1
  741. [ 4.644379@2] enter spdif_dit_probe
  742. [ 4.647835@2] codec_name = es8323.4-0010
  743. [ 4.651607@2] fuwei aml,audio-routing-es8323
  744. [ 4.655993@2] Es8323 id read invalid, id=56
  745. [ 4.660102@2] es8323_set_bias_level----686, BIAS_ON
  746. [ 5.193990@2] es8323_set_bias_level----686, BIAS_PREPARE
  747. [ 5.194197@2] es8323 4-0010: ASoC: no sink widget found for Left Out 1
  748. [ 5.200166@2] es8323 4-0010: ASoC: Failed to add route Left Mixer -> direct -> Left Out 1
  749. [ 5.208329@2] es8323 4-0010: ASoC: no source widget found for Left Out 1
  750. [ 5.214997@2] es8323 4-0010: ASoC: Failed to add route Left Out 1 -> direct -> LOUT1
  751. [ 5.222705@2] es8323 4-0010: ASoC: no sink widget found for Right Out 1
  752. [ 5.229299@2] es8323 4-0010: ASoC: Failed to add route Right Mixer -> direct -> Right Out 1
  753. [ 5.237634@2] es8323 4-0010: ASoC: no source widget found for Right Out 1
  754. [ 5.244383@2] es8323 4-0010: ASoC: Failed to add route Right Out 1 -> direct -> ROUT1
  755. [ 5.252176@2] es8323 4-0010: ASoC: no sink widget found for Left Out 2
  756. [ 5.258684@2] es8323 4-0010: ASoC: Failed to add route Left Mixer -> direct -> Left Out 2
  757. [ 5.266833@2] es8323 4-0010: ASoC: no source widget found for Left Out 2
  758. [ 5.273499@2] es8323 4-0010: ASoC: Failed to add route Left Out 2 -> direct -> LOUT2
  759. [ 5.281223@2] es8323 4-0010: ASoC: no sink widget found for Right Out 2
  760. [ 5.287809@2] es8323 4-0010: ASoC: Failed to add route Right Mixer -> direct -> Right Out 2
  761. [ 5.296131@2] es8323 4-0010: ASoC: no source widget found for Right Out 2
  762. [ 5.302884@2] es8323 4-0010: ASoC: Failed to add route Right Out 2 -> direct -> ROUT2
  763. [ 5.310726@2] --------------------- es 8323 init ok -----------------------------
  764. [ 5.318159@2] ES8323: Audio Codec Driver v1.0
  765. [ 5.323476@2] entern aml_asoc_init : mic_det=0
  766. [ 5.326996@2] hp detect paraments: h=800,l=300,mic=0,det=5,ch=1
  767. [ 5.333566@2] aml-i2s 0:playback preallocate_dma_buffer: area=ef440000, addr=2f440000, size=131072
  768. [ 5.342352@2] aml-i2s 1:capture preallocate_dma_buffer: area=ef480000, addr=2f480000, size=65536
  769. [ 5.350674@2] aml_snd_m8 aml_m8_sound_card.4: es8323-hifi <-> aml-i2s-dai.0 mapping ok
  770. [ 5.359250@2] aml-i2s 0:playback preallocate_dma_buffer: area=ef4c0000, addr=2f4c0000, size=131072
  771. [ 5.367929@2] aml-i2s 1:capture preallocate_dma_buffer: area=ef4a0000, addr=2f4a0000, size=65536
  772. [ 5.372798@0] switch_vpu_mem_pd: viu_vd1 OFF
  773. [ 5.372801@0] switch_vpu_mem_pd: di_post OFF
  774. [ 5.372803@0] switch_vpu_mem_pd: viu_vd2 OFF
  775. [ 5.372806@0] switch_vpu_mem_pd: pic_rot2 OFF
  776. [ 5.372809@0] switch_vpu_mem_pd: pic_rot3 OFF
  777. [ 5.397729@2] aml_snd_m8 aml_m8_sound_card.4: dit-hifi <-> aml-spdif-dai.0 mapping ok
  778. [ 5.405649@2] aml_snd_m8 aml_m8_sound_card.4: ASoC: no source widget found for LOUTL
  779. [ 5.413319@2] aml_snd_m8 aml_m8_sound_card.4: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
  780. [ 5.422257@2] aml_snd_m8 aml_m8_sound_card.4: ASoC: no source widget found for LOUTR
  781. [ 5.430099@2] aml_snd_m8 aml_m8_sound_card.4: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
  782. [ 5.438900@2] aml_snd_m8 aml_m8_sound_card.4: ASoC: no source widget found for HPOL
  783. [ 5.446526@2] aml_snd_m8 aml_m8_sound_card.4: ASoC: Failed to add route HPOL -> direct -> HP
  784. [ 5.455072@2] aml_snd_m8 aml_m8_sound_card.4: ASoC: no source widget found for HPOR
  785. [ 5.462554@2] aml_snd_m8 aml_m8_sound_card.4: ASoC: Failed to add route HPOR -> direct -> HP
  786. [ 5.471751@2] input: AML-M8AUDIO hp switch as /devices/platform/aml_m8_sound_card.4/sound/card0/input3
  787. [ 5.480663@2] =aml_m8_pinmux_init==,aml_m8_pinmux_init done,---0
  788. [ 5.486498@2] GACT probability NOT on
  789. [ 5.489860@2] Mirror/redirect action on
  790. [ 5.493684@2] u32 classifier
  791. [ 5.496528@2] Actions configured
  792. [ 5.500086@2] Netfilter messages via NETLINK v0.30.
  793. [ 5.504991@2] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
  794. [ 5.511706@2] ctnetlink v0.93: registering with nfnetlink.
  795. [ 5.516848@2] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
  796. [ 5.523759@2] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
  797. [ 5.530034@2] xt_time: kernel timezone is -0000
  798. [ 5.534581@2] ip_tables: (C) 2000-2006 Netfilter Core Team
  799. [ 5.539850@2] arp_tables: (C) 2002 David S. Miller
  800. [ 5.544648@2] TCP: cubic registered
  801. [ 5.548368@2] NET: Registered protocol family 10
  802. [ 5.553306@2] mip6: Mobile IPv6
  803. [ 5.555691@2] ip6_tables: (C) 2000-2006 Netfilter Core Team
  804. [ 5.561396@2] sit: IPv6 over IPv4 tunneling driver
  805. [ 5.566926@2] NET: Registered protocol family 17
  806. [ 5.570578@2] NET: Registered protocol family 15
  807. [ 5.575364@2] Bridge firewalling registered
  808. [ 5.579425@2] Bluetooth: RFCOMM TTY layer initialized
  809. [ 5.584373@2] Bluetooth: RFCOMM socket layer initialized
  810. [ 5.589627@2] Bluetooth: RFCOMM ver 1.11
  811. [ 5.593528@2] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  812. [ 5.598998@2] Bluetooth: BNEP filters: protocol multicast
  813. [ 5.604506@2] Bluetooth: BNEP socket layer initialized
  814. [ 5.609477@2] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  815. [ 5.615561@2] Bluetooth: HIDP socket layer initialized
  816. [ 5.620676@2] NET: Registered protocol family 35
  817. [ 5.625829@2] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
  818. [ 5.633071@2] Registering SWP/SWPB emulation handler
  819. [ 5.638137@2] enter meson_pm_init
  820. [ 5.641654@2] enter meson_pm_probe!
  821. [ 5.644771@2] meson_pm_probe done !
  822. [ 5.648958@2] file system registered
  823. [ 5.652644@2] android_usb gadget: Mass Storage Function, version: 2009/09/11
  824. [ 5.658814@2] android_usb gadget: Number of LUNs=1
  825. [ 5.663569@2] lun0: LUN: removable file: (no medium)
  826. [ 5.668833@2] android_usb gadget: android_usb ready
  827. [ 5.674464@2] rtc_hym8563 0-0051: setting system clock to 2014-06-10 08:03:46 UTC (1402387426)
  828. [ 5.682052@2] ### dt-test ### No testcase data in device tree; not running tests
  829. [ 5.689517@2] meson_cpufreq: no voltage_control prop
  830. [ 5.694349@2] voltage_control = 0
  831. [ 5.699154@2] <<-GTP-INFO->> GTP driver installing...
  832. [ 5.702773@2] buf[0]=54,buf[1]=9a,err=4
  833. [ 5.706481@2] adc=421,TS_C=4,flag=1
  834. [ 5.709940@2] efuse_flag=a
  835. [ 5.712629@2] amlogic_thermal_probe, this chip is trimmed, use thermal
  836. [ 5.719138@2] amlogic-thermal aml_thermal: amlogic thermal probe start
  837. [ 5.725755@2] #thermal-cells=7
  838. [ 5.728663@2] pdata->temp_trip_count=4
  839. [ 5.732392@2] temperature=60 on trip point=0
  840. [ 5.736643@2] fixing high_freq=1608001 to 1608000 at trip point 0,level=2
  841. [ 5.743399@2] fixing low_freq=1608001 to 1608000 at trip point 0,level=2
  842. [ 5.750074@2] gpu[0].gpu_high_freq=511,tmp_level[0].gpu_high_freq=511
  843. [ 5.756609@2] cpu[0] core num==2
  844. [ 5.759695@2] gpu[0] core num==3
  845. [ 5.762903@2] temperature=70 on trip point=1
  846. [ 5.767154@2] fixing high_freq=1200001 to 1200000 at trip point 1,level=6
  847. [ 5.773916@2] fixing low_freq=1200001 to 1200000 at trip point 1,level=6
  848. [ 5.780586@2] gpu[1].gpu_high_freq=435,tmp_level[1].gpu_high_freq=435
  849. [ 5.787126@2] cpu[1] core num==2
  850. [ 5.790207@2] gpu[1] core num==3
  851. [ 5.793415@2] temperature=80 on trip point=2
  852. [ 5.797666@2] fixing high_freq=800001 to 696000 at trip point 2,level=11
  853. [ 5.804340@2] fixing low_freq=800001 to 696000 at trip point 2,level=11
  854. [ 5.810925@2] gpu[2].gpu_high_freq=328,tmp_level[2].gpu_high_freq=328
  855. [ 5.817459@2] cpu[2] core num==1
  856. [ 5.820546@2] gpu[2] core num==1
  857. [ 5.823758@2] temperature=110 on trip point=3
  858. [ 5.828087@2] fixing high_freq=-1 to -22 at trip point 3,level=-1
  859. [ 5.834159@2] fixing low_freq=-1 to -22 at trip point 3,level=-1
  860. [ 5.840137@2] gpu[3].gpu_high_freq=-1,tmp_level[3].gpu_high_freq=-1
  861. [ 5.846499@2] cpu[3] core num==-1
  862. [ 5.849671@2] gpu[3] core num==-1
  863. [ 5.852966@2] idle interval=1000
  864. [ 5.856178@2] pdata->name:aml_thermal
  865. [ 5.859963@2] tmp_trip[0].cpu_core_upper=2
  866. [ 5.863903@2] tmp_trip[1].cpu_core_upper=2
  867. [ 5.867968@2] tmp_trip[2].cpu_core_upper=3
  868. [ 5.872042@2] tmp_trip[3].cpu_core_upper=-1
  869. [ 5.876329@2] aml_thermal bind thermal-cpucore-0 okay !
  870. [ 5.881418@2] aml_thermal bind thermal-cpufreq-0 okay !
  871. [ 5.886926@2] amlogic: Kernel Thermal management registered
  872. [ 5.892148@2] amlogic-thermal aml_thermal: amlogic thermal probe done
  873. [ 5.898609@2] hdmitx: cec: CEC init
  874. [ 5.902058@0] hdmitx: cec: CEC task process
  875. [ 5.902152@2] input: cec_input as /devices/virtual/input/input4
  876. [ 5.902244@2] hdmitx: cec: hdmitx_device->cec_init_ready:0x1
  877. [ 5.9022[ 5.943658@2] Changing uart_ao_ttyS0: baud from 0 to 115200
  878. [ 5.963768@2] Freeing unused kernel memory: 220K (c0967000 - c099e000)
  879. [ 5.987408@3] SELinux: Permission attach_queue in class tun_socket not defined in policy.
  880. [ 5.990027@3] SELinux: the above unknown classes and permissions will be denied
  881. [ 6.155664@2] i2c i2c-0: [aml_i2c_xfer] error ret = -5 (-EIO) token 1, master_no(0) 100K addr 0x32
  882. [ 6.159888@2] i2c i2c-0: [aml_i2c_xfer] error ret = -5 (-EIO) token 1, master_no(0) 100K addr 0x32
  883. [ 6.168310@2] [RN5T618]battery vol change: 0->0
  884. [ 6.196884@3] type=1403 audit(1402387427.010:2): policy loaded auid=4294967295 ses=4294967295
  885. [ 6.199874@3] SELinux: Loaded policy from /sepolicy
  886. [ 6.206397@3] type=1404 audit(1402387427.020:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
  887. [ 6.323663@2] aml audio hp unpluged
  888. [ 7.715001@3] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
  889. [ 7.718698@3] init: command 'loglevel' r=0
  890. [ 7.722301@3] init: command 'mount' r=0
  891. [ 7.726536@3] init: command 'insmod' r=-1
  892. [ 7.730055@3] init: mount none to target failed
  893. [ 7.734538@3] init: command 'mount' r=0
  894. [ 7.741034@3] pdata->tmp_trip[0].gpu_lower_level=0
  895. [ 7.743104@3] pdata->tmp_trip[0].gpu_upper_level=0
  896. [ 7.747910@3] pdata->tmp_trip[1].gpu_lower_level=1
  897. [ 7.752638@3] pdata->tmp_trip[1].gpu_upper_level=1
  898. [ 7.757426@3] pdata->tmp_trip[2].gpu_lower_level=2
  899. [ 7.762174@3] pdata->tmp_trip[2].gpu_upper_level=2
  900. [ 7.766959@3] pdata->tmp_trip[3].gpu_lower_level=-1
  901. [ 7.771795@3] pdata->tmp_trip[3].gpu_upper_level=-1
  902. [ 7.776668@3] aml_thermal bind thermal-gpufreq-0 okay !
  903. [ 7.781852@3] gpu cooling register okay with err=0
  904. [ 7.786675@3] tmp_trip[0].gpu_core_upper=3
  905. [ 7.790693@3] max Gpu core=6
  906. [ 7.793560@3] tmp_trip[1].gpu_core_upper=3
  907. [ 7.797976@3] max Gpu core=6
  908. [ 7.800499@3] tmp_trip[2].gpu_core_upper=5
  909. [ 7.804578@3] max Gpu core=6
  910. [ 7.807430@3] tmp_trip[3].gpu_core_upper=-1
  911. [ 7.811582@3] max Gpu core=6
  912. [ 7.814457@3] aml_thermal bind thermal-gpucore-0 okay !
  913. [ 7.819645@3] gpu core cooling register okay with err=0
  914. [ 7.826216@3] Mali: Mali device driver loaded
  915. [ 7.829263@3] init: command 'insmod' r=0
  916. [ 7.833116@3] init: processing action 0xa7518 (early-init)
  917. [ 7.838591@3] init: command 'write' r=-2
  918. [ 7.842452@3] init: processing action 0xa8d10 (wait_for_coldboot_done)
  919. [ 7.848972@3] init: wait for /dev/.coldboot_done
  920. [ 8.853630@3] init: command 'wait_for_coldboot_done' r=0
  921. [ 8.853704@3] init: processing action 0xa8d58 (mix_hwrng_into_linux_rng)
  922. [ 8.859999@3] init: /dev/hw_random not found
  923. [ 8.864235@3] init: command 'mix_hwrng_into_linux_rng' r=0
  924. [ 8.869688@3] init: processing action 0xa8da0 (keychord_init)
  925. [ 8.875422@3] init: command 'keychord_init' r=0
  926. [ [ 8.886001@3] init: command 'console_init' r=0
  927. [ 8.886035@3] init: processing action 0x92fc8 (init)
  928. [ 8.889750@3] init: command 'sysclktz' r=0
  929. [ 8.894177@3] init: mount none to target failed
  930. [ 8.898423@3] init: mount none to target failed
  931. [ 8.902911@3] init: mount none to target failed
  932. [ 8.909272@3] init: mount none to target failed
  933. [ 8.925315@3] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
  934. [ 8.928776@3] init: Before e2fsck_main...
  935. [ 8.943243@3] init: After e2fsck_main...
  936. [ 8.955660@3] EXT4-fs (mmcblk0p9): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
  937. [ 8.959113@3] init: Before e2fsck_main...
  938. [ 8.963190@3] init: After e2fsck_main...
  939. [ 8.985625@3] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
  940. [ 8.989232@3] name=emmc_key nand_key
  941. [ 8.992575@3] device name=nand_key open error
  942. [ 8.997081@3] aml_keys: version 0 can not be init c09e2a4c
  943. [ 9.002457@3] name=emmc_key emmc_key
  944. [ 9.014559@2] emmc read lba=0x20, blocks=0x100 OK!
  945. [ 9.014870@2] register_aes_algorithm:488,new way
  946. [ 9.063028@2] init: /dev/hw_random not found
  947. [ 9.128354@0] type=1400 audit(1402387429.940:4): avc: denied { entrypoint } for pid=102 comm="init" path="/sbin/healthd" dev="rootfs" ino=65 scontext=u:r:healthd:s0 tcontext=u:object_r:rootfs:s0 tclass=file
  948. [ 9.142416@0] binder: 102:102 transaction failed 29189, size 0-0
  949. [ 9.146782@2] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
  950. [ 9.147176@2] init: cannot find '/system/bin/smbd', disabling 'smbd'
  951. [ 9.148216@2] init: cannot find '/system/bin/xcmid-amlogic', disabling 'xcmidware'
  952. [ 9.151386@2] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
  953. [ 9.151391@2] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
  954. [ 9.151397@2] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
  955. [ 9.151401@2] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
  956. [ 9.152904@2] vfm_map_store:rm default
  957. [ 9.152926@2] vfm_map_store:add default decoder ppmgr deinterlace amvideo
  958. [ 9.153340@2] init: property 'sys.powerctl' doesn't exist while expanding '${sys.powerctl}'
  959. [ 9.153345@2] init: powerctl: cannot expand '${sys.powerctl}'
  960. [ 9.153363@2] init: property 'sys.sysctl.extra_free_kbytes' doesn't exist while expanding '${sys.sysctl.extra_free_kbytes}'
  961. [ 9.153367@2] init: cannot expand '${sys.sysctl.extra_free_kbytes}' while writing to '/proc/sys/vm/extra_free_kbytes'
  962. [ 9.153491@2] android_usb: already disabled
  963. [ 9.155668@2] read descriptors
  964. [ [ 9.287617@1] cur_mode = 0
  965. [ 9.287638@1] [0x0] = 0x1dd0190
  966. [ 9.287808@1] [0x4] = 0xf800ca
  967. [ 9.291036@1] [0x8] = 0x82006e
  968. [ 9.293949@1] [0xc] = 0x3c0030
  969. [ 9.296912@1] [0x10] = 0x30fa0013
  970. [ 9.300673@1] init: data_integrity_guard main!
  971. [ 9.304654@1] init: is_support_system_bak sup_sys_bak:0
  972. [ 9.305409@3] type=1400 audit(1402387430.120:5): avc: denied { read write } for pid=111 comm="app_process" path="/dev/mtd/mtd1" dev="tmpfs" ino=1741 scontext=u:r:zygote:s0 tcontext=u:object_r:mtd_device:s0 tclass=chr_file
  973. [ 9.305728@0] [0x18] = 0x6f19000
  974. [ 9.305731@0] [0x1c] = 0x9f40
  975. [ 9.305733@0] [0x20] = 0x0
  976. [ 9.305736@0] [0x24] = 0x0
  977. [ 9.305738@0] [0x28] = 0x0
  978. [ 9.305740@0] set_remote_mode[48]
  979. [ 9.323856@3] type=1400 audit(1402387430.140:6): avc: denied { read write } for pid=114 comm="installd" path="/dev/mtd/mtd1" dev="tmpfs" ino=1741 scontext=u:r:installd:s0 tcontext=u:object_r:mtd_device:s0 tclass=chr_file
  980. [ 9.328615@3] type=1400 audit(1402387430.140:7): avc: denied { read write } for pid=108 comm="netd" path="/dev/mtd/mtd1" dev="tmpfs" ino=1741 scontext=u:r:netd:s0 tcontext=u:object_r:mtd_device:s0 tclass=chr_file
  981. [ 9.333143@2] type=1400 audit(1402387430.140:8): avc: denied { read write } for pid=105 comm="vold" path="/dev/mtd/mtd1" dev="tmpfs" ino=1741 scontext=u:r:vold:s0 tcontext=u:object_r:mtd_device:s0 tclass=chr_file
  982. [ 9.617647@0] Adding 511996k swap on /dev/block/zram0. Priority:-1 extents:1 across:511996k SS
  983. root@NEO-X8:/ # [ 10.274569@0] healthd: battery l=100 v=4998 t=30.0 h=2 st=1 c=0 chg=
  984. [ 10.275675@0] healthd: battery l=100 v=4998 t=30.0 h=2 st=1 c=0 chg=
  985. [ 10.282063@0] healthd: battery l=100 v=4998 t=30.0 h=2 st=1 c=0 chg=
  986. [ 10.750644@0] tvmode set to 720p
  987. [ 10.750644@0]
  988.  
  989. [ 10.750772@0] don't set the same mode as current.
  990.  
  991. [ 11.042240@0] osd0=>x:0 ,y:0,w:1280,h:720
  992.  
  993. [ 11.042240@0] osd1=> x:0,y:0,w:18,h:18
  994.  
  995. [ 11.096135@0] buf=0
  996. [ 11.096135@0]
  997. [ 11.096255@0] IEC958_mode_raw=0
  998. [ 12.165680@2] i2c i2c-0: [aml_i2c_xfer] error ret = -5 (-EIO) token 1, master_no(0) 100K addr 0x32
  999. [ 12.653024@3] IEC958_mode_codec/0 Digital codec type: 0-pcm
  1000. [ 12.653221@3] IEC958_mode_codec/0 Digital codec type: 0-pcm
  1001. [ 12.658733@3] IEC958_mode_codec/0 Digital codec type: 0-pcm
  1002. [ 12.665096@3] IEC958_mode_codec/0 Digital codec type: 0-pcm
  1003. [ 12.669840@3] IEC958_mode_codec/0 Digital codec type: 0-pcm
  1004. [ 12.676353@3] IEC958_mode_codec/0 Digital codec type: 0-pcm
  1005. [ 12.680817@3] IEC958_mode_codec/0 Digital codec type: 0-pcm
  1006. [ 12.686583@3] IEC958_mode_codec/0 Digital codec type: 0-pcm
  1007. [ 12.691991@3] IEC958_mode_codec/0 Digital codec type: 0-pcm
  1008. [ 12.697797@3] IEC958_mode_codec/0 Digital codec type: 0-pcm
  1009. [ 12.703025@3] IEC958_mode_codec/0 Digital codec type: 0-pcm
  1010. [ 13.392302@1] SELinux: (dev zram0, type ext2) has no xattr support
  1011. [ 14.969892@0] warning: `zygote' uses 32-bit capabilities (legacy support in use)
  1012. [ 15.986195@3] IRQ95 no longer affine to CPU3
  1013. [ 15.986393@1] CPU3: shutdown
  1014. [ 16.043931@2] IRQ94 no longer affine to CPU2
  1015. [ 16.044119@1] CPU2: shutdown
  1016. [ 41.304295@0] i2c i2c-0: [aml_i2c_xfer] error ret = -5 (-EIO) token 1, master_no(0) 100K addr 0x32
  1017. [ 41.514087@0] healthd: battery l=100 v=4998 t=30.0 h=2 st=1 c=0 chg=
  1018. [ 41.523939@0] request_suspend_state: wakeup (3->0) at 41450281000 (2014-06-10 08:04:22.349488000 UTC)
  1019. [ 41.527512@0] request_suspend_state,169,old_sleep=0,new_state=0
  1020. [ 41.633496@0] lowmemorykiller: lowmem_shrink: convert oom_adj to oom_score_adj:
  1021. [ 41.633500@0] lowmemorykiller: oom_adj 0 => oom_score_adj 0
  1022. [ 41.633501@0] lowmemorykiller: oom_adj 2 => oom_score_adj 117
  1023. [ 41.633503@0] lowmemorykiller: oom_adj 4 => oom_score_adj 235
  1024. [ 41.633504@0] lowmemorykiller: oom_adj 6 => oom_score_adj 352
  1025. [ 41.633505@0] lowmemorykiller: oom_adj 9 => oom_score_adj 529
  1026. [ 41.633506@0] lowmemorykiller: oom_adj 15 => oom_score_adj 1000
  1027. [ 41.852261@0] type=1400 audit(1402387462.660:9): avc: denied { module_request } for pid=425 comm="netd" kmod="netdev-ppp0" scontext=u:r:netd:s0 tcontext=u:r:kernel:s0 tclass=system
  1028. [ 41.863137@0] type=1400 audit(1402387462.680:10): avc: denied { sys_module } for pid=425 comm="netd" capability=16 scontext=u:r:netd:s0 tcontext=u:r:netd:s0 tclass=capability
  1029. [ 41.882010@0] type=1400 audit(1402387462.700:11): avc: denied { module_request } for pid=425 comm="netd" kmod="netdev-ppp0" scontext=u:r:netd:s0 tcontext=u:r:kernel:s0 tclass=system
  1030. [ 41.882024@0] type=1400 audit(1402387462.700:12): avc: denied { sys_module } for pid=425 comm="netd" capability=16 scontext=u:r:netd:s0 tcontext=u:r:netd:s0 tclass=capability
  1031. [ 41.884656@0] type=1400 audit(1402387462.700:13): avc: denied { module_request } for pid=425 comm="netd" kmod="netdev-ppp0" scontext=u:r:netd:s0 tcontext=u:r:kernel:s0 tclass=system
  1032. [ 41.884669@0] type=1400 audit(1402387462.700:14): avc: denied { sys_module } for pid=425 comm="netd" capability=16 scontext=u:r:netd:s0 tcontext=u:r:netd:s0 tclass=capability
  1033. [ 41.887514@0] type=1400 audit(1402387462.700:15): avc: denied { module_request } for pid=425 comm="netd" kmod="netdev-ppp0" scontext=u:r:netd:s0 tcontext=u:r:kernel:s0 tclass=system
  1034. [ 41.887528@0] type=1400 audit(1402387462.700:16): avc: denied { sys_module } for pid=425 comm="netd" capability=16 scontext=u:r:netd:s0 tcontext=u:r:netd:s0 tclass=capability
  1035. [ 42.162327@0] acc_open
  1036. [ 42.162370@0] acc_release
  1037. [ 42.349039@0] init: no such service 'wififix'
  1038. [ 42.407667@1] +++dhd_module_init+++
  1039. [ 42.407717@1] wifi_setup_dt
  1040. [ 42.408305@1] wifi_request_32k_clk : ON-->ON for sdio_wifi
  1041. [ 42.414925@1] interrupt_pin(133) : (null)
  1042. [ 42.420022@1] reg:2620,clearmask=100010,setmask=0
  1043. [ 42.422521@1] reg:2622,clearmask=ff,set pin=133
  1044. [ 42.427027@1] reg:2623,clearmask=70000,setmask=4
  1045. [ 42.433056@1] interrupt_pin(133) : sdio_wifi
  1046. [ 42.436681@1] power_on_pin(123) : (null)
  1047. [ 42.436703@1] power_on_pin(123) : sdio_wifi
  1048. [ 42.436745@1] WIFI Disable! 123
  1049. [ 42.695815@1] WIFI Enable! 123
  1050. [ 42.803776@1] write pen_release: 2
  1051. [ 42.803971@2] CPU2: Booted secondary processor
  1052. [ 43.009003@0] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
  1053. [ 43.010357@0] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
  1054. [ 43.016263@0] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
  1055. [ 43.022949@0] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
  1056. [ 43.064872@0] sdio: new high speed SDIO card at address 0001, clock 35416666, 4-bit-bus-width
  1057. [ 43.097611@2] [sdio_reinit] finish
  1058. [ 43.097844@2] =========== WLAN placed in POWER ON ========
  1059. [ 43.102329@2] bcmsdh_register: Linux Kernel SDIO/MMC Driver
  1060. [ 43.115140@0] dhd_customer_oob_irq_map: customer specific Host GPIO number is (100)
  1061. [ 43.119569@0] F1 signature OK, socitype:0x1 chip:0x4330 rev:0x4 pkg:0x0
  1062. [ 43.119913@0] DHD: dongle ram size is set to 294912(orig 294912) at 0x0
  1063. [ 43.120132@0] dhd_conf_set_fw_name_by_chip: firmware_path=/etc/wifi/40183/fw_bcm40183b2.bin
  1064. [ 43.120688@0] wl_create_event_handler(): thread:wl_event_handler:279 started
  1065. [ 43.120691@1] tsk Enter, tsk = 0xeaa41444
  1066. [ 43.120875@0] dhd_attach(): thread:dhd_watchdog_thread:27a started
  1067. [ 43.120902@0] dhd_attach(): thread:dhd_dpc:27b started
  1068. [ 43.120931@0] dhd_attach(): thread:dhd_sysioc:27c started
  1069. [ 43.122646@0] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33
  1070. [ 43.133981@1]
  1071. [ 43.133981@1] Dongle Host Driver, version 1.88.45.3 (r420671)
  1072. [ 43.133981@1] Compiled in drivers/net/wireless/bcmdhd on May 27 2014 at 20:27:36
  1073. [ 43.146604@1] =========== WLAN placed in RESET ========
  1074. [ 43.146607@1] ---dhd_module_init---
  1075. [ 43.491789@0] type=1400 audit(1402387464.300:17): avc: denied { getattr } for pid=692 comm="zygote" path="socket:[264]" dev="sockfs" ino=264 scontext=u:r:untrusted_app:s0 tcontext=u:r:zygote:s0 tclass=unix_stream_socket
  1076. [ 43.491976@0] type=1400 audit(1402387464.300:18): avc: denied { getopt } for pid=692 comm="zygote" path="/dev/socket/zygote" scontext=u:r:untrusted_app:s0 tcontext=u:r:zygote:s0 tclass=unix_stream_socket
  1077. [ 43.603997@1] write pen_release: 3
  1078. [ 43.604238@3] CPU3: Booted secondary processor
  1079. [ 45.231598@2] dhd_open: Enter ebfe6800
  1080. [ 45.231647@2] dhd_conf_set_fw_name_by_chip: firmware_path=/etc/wifi/40183/fw_bcm40183b2.bin
  1081. [ 45.238094@2]
  1082. [ 45.238094@2] Dongle Host Driver, version 1.88.45.3 (r420671)
  1083. [ 45.238094@2] Compiled in drivers/net/wireless/bcmdhd on May 27 2014 at 20:27:36
  1084. [ 45.253040@2] wl_android_wifi_on in 1
  1085. [ 45.253047@2] wl_android_wifi_on in 2: g_wifi_on=0
  1086. [ 45.253055@2] WIFI Disable! 123
  1087. [ 45.463787@2] WIFI Enable! 123
  1088. [ 45.663663@2] sdio_reset_comm():
  1089. [ 45.819013@0] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
  1090. [ 45.820934@0] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
  1091. [ 45.826918@0] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
  1092. [ 45.830131@0] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
  1093. [ 45.886243@0] [sdio_reinit] finish
  1094. [ 45.988674@3] =========== WLAN going back to live ========
  1095. [ 46.216257@0]
  1096. [ 46.216257@0]
  1097. [ 46.216257@0] dhd_bus_devreset: == WLAN ON ==
  1098. [ 46.216261@0] dhd_bus_devreset called when dongle is not in reset
  1099. [ 46.216264@0] Will call dhd_bus_start instead
  1100. [ 46.216347@0] dhd_conf_set_fw_name_by_chip: firmware_path=/etc/wifi/40183/fw_bcm40183b2.bin
  1101. [ 46.218195@0] Final fw_path=/etc/wifi/40183/fw_bcm40183b2.bin
  1102. [ 46.218199@0] Final nv_path=/etc/wifi/40183/nvram.txt
  1103. [ 46.218202@0] Final conf_path=/system/etc/firmware/config.txt
  1104. [ 46.482924@0] NVRAM version: AP6330_NVRAM_V1.0_20121130
  1105.  
  1106. [ 46.484380@0] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
  1107. [ 46.774316@1] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
  1108. [ 46.774840@1] bcmsdh_set_drvdata: Enter
  1109. [ 46.778641@1] bcmsdh_register_oob_intr: Enter
  1110. [ 46.783432@1] bcmsdh_register_oob_intr: IRQ=100 Type=414
  1111. [ 46.802904@1] dhd_conf_set_band: Set band 0
  1112. [ 46.805127@1] Firmware up: op_mode=0x0005, Broadcom Dongle Host Driver mac=98:3b:16:1f:a7:66
  1113. [ 46.805130@1] dhd_conf_set_country: Set country ALL, revision 0
  1114. [ 46.881676@1] Country code: ALL (ALL/0)
  1115. [ 46.885778@1] dhd_conf_set_roam: Set roam_off 1
  1116. [ 46.902854@2] Driver: 1.88.45.3 (r420671)
  1117. [ 46.902854@2] Firmware: wl0: Jan 6 2014 15:11:29 version 5.90.195.89.13 FWID 01-72f124c5
  1118. [ 46.911399@2] wl_android_wifi_on: Success
  1119. [ 47.201112@1] audit_printk_skb: 6 callbacks suppressed
  1120. [ 47.201159@1] type=1400 audit(1402387468.010:21): avc: denied { module_request } for pid=425 comm="netd" kmod="netdev-p2p0" scontext=u:r:netd:s0 tcontext=u:r:kernel:s0 tclass=system
  1121. [ 47.232963@1] type=1400 audit(1402387468.040:22): avc: denied { sys_module } for pid=425 comm="netd" capability=16 scontext=u:r:netd:s0 tcontext=u:r:netd:s0 tclass=capability
  1122. [ 47.246932@3] type=1400 audit(1402387468.060:23): avc: denied { module_request } for pid=425 comm="netd" kmod="netdev-p2p0" scontext=u:r:netd:s0 tcontext=u:r:kernel:s0 tclass=system
  1123. [ 47.246947@3] type=1400 audit(1402387468.060:24): avc: denied { sys_module } for pid=425 comm="netd" capability=16 scontext=u:r:netd:s0 tcontext=u:r:netd:s0 tclass=capability
  1124. [ 47.246975@3] type=1400 audit(1402387468.060:25): avc: denied { module_request } for pid=425 comm="netd" kmod="netdev-p2p0" scontext=u:r:netd:s0 tcontext=u:r:kernel:s0 tclass=system
  1125. [ 47.246991@3] type=1400 audit(1402387468.060:26): avc: denied { sys_module } for pid=425 comm="netd" capability=16 scontext=u:r:netd:s0 tcontext=u:r:netd:s0 tclass=capability
  1126. [ 47.247012@3] type=1400 audit(1402387468.060:27): avc: denied { module_request } for pid=425 comm="netd" kmod="netdev-p2p0" scontext=u:r:netd:s0 tcontext=u:r:kernel:s0 tclass=system
  1127. [ 47.247024@3] type=1400 audit(1402387468.060:28): avc: denied { sys_module } for pid=425 comm="netd" capability=16 scontext=u:r:netd:s0 tcontext=u:r:netd:s0 tclass=capability
  1128. [ 47.250237@3] type=1400 audit(1402387468.060:29): avc: denied { module_request } for pid=425 comm=
  1129. [ 48.174168@0] osd0=>x:0 ,y:0,w:1280,h:720
  1130.  
  1131. [ 48.174168@0] osd1=> x:0,y:0,w:18,h:18
  1132.  
  1133. [ 48.434640@0] init: data_integrity_guard isBootCompleted:1!
  1134. [ 51.226021@1] connect failed event=0 e->status 1 e->reason 0
  1135. [ 51.226926@1] CFG80211-ERROR) wl_bss_connect_done : Report connect result - connection failed
  1136. [ 51.456225@1] CPU2: shutdown
  1137. [ 51.515799@1] CPU3: shutdown
  1138. [ 52.155826@0] CPU1: shutdown
  1139. [ 55.231994@0] connect failed event=0 e->status 1 e->reason 0
  1140. [ 55.234551@0] CFG80211-ERROR) wl_bss_connect_done : Report connect result - connection failed
  1141. [ 59.245401@0] wl_bss_connect_done succeeded with 00:80:5a:5b:ae:cc
  1142. [ 59.329869@0] wl_notify_connect_status nothing
  1143. [ 59.329914@0] wl_bss_connect_done succeeded with 00:80:5a:5b:ae:cc
  1144. [ 59.438056@0] net_ratelimit: 6 callbacks suppressed
  1145. [ 59.438091@0] dhd_pno_get_for_batch : wifi location service is not supported
  1146. [ 59.444394@0] ANDROID-ERROR) failed to getting batching results
  1147. [ 59.450847@0] dhd_pno_stop_for_batch : wifi location service is not supported
  1148. [ 59.457498@0] NULL POINTER (_dhd_pno_clear_all_batch_results) : head->next is NULL
  1149. [ 59.464888@0] NULL POINTER (_dhd_pno_clear_all_batch_results) : head->next is NULL
  1150. [ 59.472399@0] ANDROID-ERROR) failed to stop batching scan
  1151. [ 63.524635@0] CPU: 0 PID: 714 Comm: NetworkTimeUpda Not tainted 3.10.33 #6
  1152. [ 63.525884@0] [<c0014b58>] (unwind_backtrace+0x0/0xf8) from [<c0011c54>] (show_stack+0x10/0x14)
  1153. [ 63.534722@0] [<c0011c54>] (show_stack+0x10/0x14) from [<c046765c>] (hym8563_set_time+0x250/0x25c)
  1154. [ 63.543517@0] [<c046765c>] (hym8563_set_time+0x250/0x25c) from [<c0313478>] (rtc_set_time+0x5c/0xcc)
  1155. [ 63.552717@0] [<c0313478>] (rtc_set_time+0x5c/0xcc) from [<c038c000>] (alarm_ioctl+0x360/0x49c)
  1156. [ 63.561267@0] [<c038c000>] (alarm_ioctl+0x360/0x49c) from [<c00ca2ec>] (do_vfs_ioctl+0x570/0x5bc)
  1157. [ 63.570199@0] [<c00ca2ec>] (do_vfs_ioctl+0x570/0x5bc) from [<c00ca388>] (SyS_ioctl+0x50/0x78)
  1158. [ 63.578745@0] [<c00ca388>] (SyS_ioctl+0x50/0x78) from [<c000e100>] (ret_fast_syscall+0x0/0x30)
  1159. [ 78.986945@0] write pen_release: 1
  1160. [ 78.987104@1] CPU1: Booted secondary processor
  1161. [ 79.746170@1] migrate_irqs: 12 callbacks suppressed
  1162. [ 79.746173@1] IRQ93 no longer affine to CPU1
  1163. [ 79.746389@0] CPU1: shutdown
  1164. [ 79.984463@0] write pen_release: 1
  1165. [ 79.984623@1] CPU1: Booted secondary processor
  1166. [ 81.566033@1] IRQ93 no longer affine to CPU1
  1167. [ 81.566244@0] CPU1: shutdown
  1168. [ 82.163231@0] input: anymote as /devices/virtual/input/input5
  1169. [ 82.303884@0] write pen_release: 1
  1170. [ 82.304048@1] CPU1: Booted secondary processor
  1171. [ 85.086176@1] IRQ93 no longer affine to CPU1
  1172. [ 85.086382@0] CPU1: shutdown
  1173. [ 85.804028@0] write pen_release: 1
  1174. [ 85.804194@1] CPU1: Booted secondary processor
  1175. [ 87.865900@1] IRQ93 no longer affine to CPU1
  1176. [ 87.866117@0] CPU1: shutdown
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!