...[60]HELLO! BOOT0 is starting!
[63]BOOT0 commit : 3ae35eb
[66]set pll start
[68]periph0 has been enabled
[71]set pll end
[73]unknow PMU
[75]PMU: AXP806
[77]dram return write ok
[79]board init ok
[81]DRAM BOOT DRIVE INFO: V0.648
[84]the chip id is 0x5c00
[87]chip id check OK
[89]DRAM_VCC set to 1500 mv
[92]DRAM CLK =600 MHZ
[94]DRAM Type =3 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4)
[102]Actual DRAM SIZE =1024 M
[105]DRAM SIZE =1024 MBytes, para1 = 30eb, para2 = 4000000, dram_tpr13 = 6041
[118]DRAM simple test OK.
[120]rtc standby flag is 0x0, super standby flag is 0x0
[126]dram size =1024
[129]card no is 2
[130]sdcard 2 line count 8
[133][mmc]: mmc driver ver 2021-10-12 13:56
[137][mmc]: b mmc 2 bias 4
[145][mmc]: Wrong media type 0x0, but host sdc2, try mmc first
[151][mmc]: ***Try MMC card 2***
[189][mmc]: RMCA OK!
[192][mmc]: MMC 5.0
[194][mmc]: HSSDR52/SDR25 8 bit
[197][mmc]: 50000000 Hz
[199][mmc]: 15028 MB
[201][mmc]: ***SD/MMC 2 init OK!!!***
[276]Loading boot-pkg Succeed(index=0).
[280][mmc]: b mmc 2 bias 4
[282]Entry_name        = u-boot
[292]Entry_name        = monitor
[295]Entry_name        = dtbo
[298]Entry_name        = dtb
[302]tunning data addr:0x4a0003e8
[305]Jump to second Boot.
NOTICE:  BL3-1: v1.0(debug):05d6c57
NOTICE:  BL3-1: Built : 13:35:35, 2021-10-28
NOTICE:  BL3-1 commit: 8
NOTICE:  cpuidle init version V2.0
ERROR:   Error initializing runtime service tspd_fast
NOTICE:  BL3-1: Preparing for EL3 exit to normal world
NOTICE:  BL3-1: Next image address = 0x4a000000
NOTICE:  BL3-1: Next image spsr = 0x1d3
ˇ

U-Boot 2018.05 (Jul 15 2022 - 13:48:08 +0800) Allwinner Technology

[00.382]CPU:   Allwinner Family
[00.385]Model: sun50iw9
I2C:   ready
[00.389]DRAM:  1 GiB
[00.392]Relocation Offset is: 35ebf000
[00.433]secure enable bit: 0
[00.436]pmu_axp152_probe pmic_bus_read fail
[00.440]PMU: AXP806
[00.445]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=400Mhz
[00.633]sunxi overlay merged okqv
[00.637]drv_disp_init
[00.667]__clk_enable: clk is null.
[00.673]drv_disp_init finish
[00.675]gic: sec monitor mode
[00.705]flash init start
[00.707]workmode = 0,storage type = 2
[00.711]MMC:. 2
[00.712][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00
[00.718][mmc]: get sdc_type fail and use default host:tm4.
[00.729][mmc]: SUNXI SDMMC Controller Version:0x40502
[00.773][mmc]: Best spd md: 4-HS400, freq: 3-100000000, Bus width: 8
[00.779]sunxi flash init ok
[00.782]Loading Environment from SUNXI_FLASH... OK
[00.792]usb burn from boot
delay time 0
weak:otg_phy_config
[00.805]usb prepare ok
[01.608]overtime
[01.612]do_burn_from_boot usb : no usb exist
[01.616]boot_gui_init:start
FAT: Misaligned buffer address (7be7b598)
32 bytes read in 3 ms (9.8 KiB/s)
tcon_de_attach:de=0,tcon=2[01.898]boot_gui_init:finish
[01.901]bmp_name=bootlogo.bmp
3686456 bytes read in 23 ms (152.9 MiB/s)
[01.939]update dts
** Unrecognized filesystem type **
[01.948]load file(ULI/factory/rootwait init.txt) error.
** Unrecognized filesystem type **
[01.960]load file(ULI/factory/snum.txt) error.
[01.964]name in map mac
** Unrecognized filesystem type **
[01.974]load file(ULI/factory/wifi_mac.txt) error.
** Unrecognized filesystem type **
[01.985]load file(ULI/factory/bt_mac.txt) error.
** Unrecognized filesystem type **
[01.996]load file(ULI/factory/selinux.txt) error.
** Unrecognized filesystem type **
[02.008]load file(ULI/factory/specialstr.txt) error.
[02.017]update part info
[02.038]update bootcmd
[02.040]No ethernet found.
Hit any key to stop autoboot:  0
[02.223]Starting kernel ...

[02.226][mmc]: mmc exit start
[02.265][mmc]: mmc 2 exit ok
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.170 (yxt-rd03@yxt-rd02-server) (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05) ) #1 SMP PREEMPT Fri Jul 15 13:50:03 CST 2022
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] bootconsole [earlycon0] enabled
[    0.028252] BOOTEVENT:        28.246666: ON
[    0.247528] sunxi_i2c_probe()2209 - [i2c3] warning: failed to get regulator id
[    0.248241] sunxi_i2c_probe()2209 - [i2c5] warning: failed to get regulator id
[    0.298425] [ac200] get ave_regulator_name failed!
[    0.298898] [ac200] pwm enable
[    0.381260] failed to get standbyŗ[    0.385135] uart uart1: get regulator failed
[    0.411241] [NAND][NE] Not found valid nand node on dts
[    0.418995] sunxi-wlan soc@03000000:wlan: get gpio chip_en failed
[    0.425873] sunxi-wlan soc@03000000:wlan: get gpio power_en failed
[    0.554968] hci: request ohci1-controller gpio:232
[    0.745765] axp2101_pek: axp2101-pek can not register without irq
[    0.754965] sunxi_ir_startup: get ir protocol failed
[    0.762426] VE: get debugfs_mpp_root is NULL, please check mpp
[    0.762426]
[    0.770701] VE: sunxi ve debug register driver failed!
[    0.770701]
[    0.785122] mmc:failed to get gpios
[    0.860810] mmc:failed to get gpios
[    0.897150] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RTO !!
[    0.903945] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RTO !!
[    0.914392] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RTO !!
[    0.915357] [sunxi_internal_codec_probe]:get audio avcc failed
[    0.915385] [sunxi_internal_codec_probe]:get audio vcc3v3-audio failed
[    0.915574] [audio-codec]dachpf_cfg configurations missing or invalid.
[    0.915584] lineout_vol:26, linein_gain:3, fmin_gain:3, digital_vol:0, adcdrc_cfg:0, adchpf_cfg:0, dacdrc_cfg:0, dachpf_cfg:0, ramp_func_used:1, pa_msleep_time:160, pa_ctl_level:0, gpio-spk:0
[    0.961466] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RTO !!
[    0.963520] sndhdmi sndhdmi: ASoC: CPU DAI (null) not registered
[    0.963527] sndhdmi sndhdmi: snd_soc_register_card() failed: -517
[    0.965085] sunxi-ahub-cpudai 5097000.cpudai3-controller: ahub cpudai id invalid
[    0.990075] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RTO !!
[    0.996770] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RTO !!
[    1.015385] ERROR: pinctrl_get for HDMI2.0 DDC fail
[    1.027050] tv_probe()1435 - of_property_read_string tv_power failed!
[    1.119713] cpu cpu1: opp_list_debug_create_link: Failed to create link
[    1.127205] cpu cpu1: _add_opp_dev: Failed to register opp debugfs (-12)
[    1.134795] cpu cpu2: opp_list_debug_create_link: Failed to create link
[    1.142250] cpu cpu2: _add_opp_dev: Failed to register opp debugfs (-12)
[    1.149831] cpu cpu3: opp_list_debug_create_link: Failed to create link
[    1.157291] cpu cpu3: _add_opp_dev: Failed to register opp debugfs (-12)
[    1.534836] selinux: avc:  denied  { set } for  scontext=u:r:vendor_init:s0 tcontext=u:object_r:default_prop:s0 tclass=property_service permissive=1
[    1.534836]
[    1.552504] selinux: avc:  denied  { set } for  scontext=u:r:vendor_init:s0 tcontext=u:object_r:dalvik_prop:s0 tclass=property_service permissive=1
[    1.552504]
[    2.146904] FAT-fs (mmcblk0p15): bogus number of reserved sectors
console:/ $ [    2.894648] apexd: Failed to walk /product/apex : Can't open /product/apex for reading : No such file or directory
[   12.510714] [CEC]cec_CfgLogicAddr failed
[   12.515369] [CEC]cec_CfgLogicAddr failed
[   13.556769] ======== XRADIO WIFI OPEN ========
[   13.945120] [CEC]cec_CfgLogicAddr failed
[   14.050530] sunxi-gmac gmac1 eth0: No PHY found!
[   14.096313] sunxi-gmac gmac1 eth0: phy init again...
[   15.418788] [XRADIO] Driver Label:XR_V02.15.74   Jul 15 2022 13:49:48
[   15.426697] [XRADIO] Allocated hw_priv @ ffffffc0022017a0
[   15.583278] [XRADIO] Detect SDIO card 1
[   15.638468] [SBUS] XRadio Device:sdio clk=50000000
[   15.648038] [XRADIO] XRADIO_HW_REV 1.0 detected.
[   15.791297] [XRADIO] Bootloader complete
[   15.897621] [XRADIO] Firmware completed.
[   15.908322] [WSM] Firmware Label:XR_C01.08.52.65 Jul 16 2019 11:09:57
[   15.916908] [XRADIO] Firmware Startup Done.
[   16.313603] [STA] !!!xradio_vif_setup: id=0, type=2, p2p=0, addr=a4:e9:46:30:2b:17
[   16.341015] [AP_WRN] BSS_CHANGED_ASSOC but driver is unjoined.
[   16.580986] [STA] !!!xradio_vif_setup: id=2, type=10, p2p=0, addr=a4:e9:46:30:2b:18
[   26.889045] apexd: Can't open /product/apex for reading : No such file or directory