Guest User

Kernel 3.10.22 booting on Amlogic MX platform

a guest
Mar 14th, 2014
859
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. EEEE I3000000032940xf100100303;77510EEEE I400000004294_M6_BL1_3003>2137333
  2. TE : 126298
  3. BT : 03:40:18 Mar 15 2014
  4.  
  5. CPU clock is 1200MHz
  6.  
  7. wait pll-0x03 target is 0204 now it is 0x00000203
  8.  
  9. DDR clock is 516MHz with Low Power & 1T mode
  10.  
  11. DDR training :
  12. DX0DLLCR:40000000
  13. DX0DQTR:ffffffff
  14. DX0DQSTR:3db05001
  15. DX1DLLCR:40000000
  16. DX1DQTR:ffffffff
  17. DX1DQSTR:3db05001
  18. DX2DLLCR:40000000
  19. DX2DQTR:ffffffff
  20. DX2DQSTR:3db05001
  21. DX3DLLCR:40000000
  22. DX3DQTR:ffffffff
  23. DX3DQSTR:3db05001
  24. Stage 00 Result 00000000
  25. Stage 01 Result 00000000
  26. Stage 02 Result 00000000
  27. Stage 03 Result 00000000
  28.  
  29. DDR init use : 41812 us
  30.  
  31. HHH
  32. BootFrom SPI
  33. 0x12345678
  34. Boot from int dev 1stSPI RESERVED
  35.  
  36. TE : 395444
  37.  
  38. System Started
  39.  
  40.  
  41. U-boot(m6_vt_atv102s@) (Mar 15 2014 - 03:40:02)
  42.  
  43. aml_rtc_init
  44. aml rtc init first time!
  45. clr h-ram
  46. DRAM: 1 GiB
  47. relocation Offset is: 105e4000
  48. MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
  49. [mmc_register] add mmc dev_num=1, port=2, if_type=6
  50. SDIO Port B: 0, SDIO Port C: 1
  51. aml_i2c_init
  52. NAND: Amlogic nand flash uboot driver, Version U1.06.017 (c) 2010 Amlogic Inc.
  53. SPI BOOT : continue i 0
  54. No NAND device found!!!
  55. NAND device id: 2c 68 4 4a a9 0
  56. NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron C revision NAND 4GiB MT29F32G-C)
  57. 1 NAND chips detected
  58. #####aml_nand_init, with RB pins and chip->chip_delay:20
  59. bus_cycle=5, bus_timing=6, start_cycle=6, end_cycle=7,system=5.0ns
  60. oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH30_1K_MODE
  61. aml_chip->oob_fill_cnt =0,aml_chip->oob_size =224,bch_bytes =54
  62. aml_nand_init:oobmul =2,chip->ecc.layout->oobfree[0].length=16,aml_chip->oob_size=224
  63. aml nand env valid addr: 10000 ,status =0
  64. NAND bbt detect factory Bad block at ffc00000
  65. NAND bbt detect factory Bad block at ff800000
  66. NAND bbt detect factory Bad block at ff400000
  67. NAND bbt detect factory Bad block at ff000000
  68. key start_blk=2036,end_blk=2047,aml_nand_key_init:684
  69. aml nand key valid addr: fea00000
  70. CONFIG_KEYSIZE=0x10000; KEYSIZE=0xfffc; bbt=0x1330; default_keyironment_size=0xeccc
  71. i=0,register --- nand_key
  72. NAND bbt detect Bad block at 0
  73. NAND bbt detect factory Bad block at 5a00000
  74. Creating 7 MTD partitions on "nandnormal":
  75. 0x000000800000-0x000001000000 : "logo"
  76. 0x000001000000-0x000001800000 : "aml_logo"
  77. 0x000001800000-0x000002000000 : "recovery"
  78. 0x000002000000-0x000002800000 : "boot"
  79. 0x000002800000-0x000042a00000 : "system"
  80. NAND bbt detect factory Bad block at 5a00000
  81. 0x000042a00000-0x000062a00000 : "cache"
  82. 0x000062a00000-0x0000fe800000 : "userdata"
  83. nandnormal initialized ok
  84. detect mx chiprevD :0 and nand_type: 0
  85. nand_curr_device =1
  86. SPI BOOT,spi_env_relocate_spec : env_relocate_spec 53
  87. SF: Detected MX25L4005 with page size 256, total 512 KiB
  88.  
  89. SPI NOR Flash NO write protect!!!, So I will enable it...
  90. In: serial
  91. Out: serial
  92. Err: serial
  93. register usb cfg[0] = 9fe86bc8
  94. Net: Meson_Ethernet
  95. init suspend firmware done. (ret:0)
  96. detect_storage
  97. nand exist return 0
  98. setenv storage nand
  99. reboot_mode=charging
  100. SARADC open channel(4).
  101. SARADC open channel(4).
  102. ir init
  103. get_adc_sample(4): 0xb7
  104. get_key(): 1
  105. get_adc_sample(4): 0xb7
  106. get_key(): 1
  107. get_adc_sample(4): 0xb7
  108. get_key(): 1
  109. get_adc_sample(4): 0xb7
  110. get_key(): 1
  111. get_adc_sample(4): 0xb7
  112. get_key(): 1
  113. upgrading... please wait
  114.  
  115. NAND read: logo whole chip
  116. 8388608 bytes read: OK
  117. unpackimg:Magic error, use old format
  118. sdio_detect return 1
  119. [mmc_init] SDIO Port B:0, if_type=7, initialized OK!
  120. Device: SDIO Port B
  121. Manufacturer ID: 0
  122. OEM: 0
  123. Name: Tran Speed: 20000000
  124. Rd Block Len: 512
  125. SD version 2.0
  126. High Capacity: Yes
  127. Capacity: 3965190144
  128. Boot Part Size: 0
  129. Bus Width: 4-bit
  130. u-boot.bin is exist
  131. reading u-boot.bin
  132.  
  133. 376848 bytes read
  134. SF: Detected MX25L4005 with page size 256, total 512 KiB
  135.  
  136. SPI NOR Flash NO write protect!!!, So I will enable it...
  137. 512 KiB MX25L4005 at 0:2 is now current device
  138. Amlogic log : SPI write 393216 bytes data used about 1994100 us
  139. recovery.img is exist
  140. reading recovery.img
  141.  
  142. 7568546 bytes read
  143.  
  144. Amlogic nand flash uboot driver, Version U1.06.017 (c) 2010 Amlogic Inc.
  145. SPI BOOT : continue i 0
  146. No NAND device found!!!
  147. NAND device id: 2c 68 4 4a a9 0
  148. NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron C revision NAND 4GiB MT29F32G-C)
  149. 1 NAND chips detected
  150. #####aml_nand_init, with RB pins and chip->chip_delay:20
  151. bus_cycle=5, bus_timing=6, start_cycle=6, end_cycle=7,system=5.0ns
  152. oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH30_1K_MODE
  153. aml_chip->oob_fill_cnt =0,aml_chip->oob_size =224,bch_bytes =54
  154. aml_nand_init:oobmul =2,chip->ecc.layout->oobfree[0].length=16,aml_chip->oob_size=224
  155. aml nand env valid addr: 10000 ,status =0
  156. mtd parttion 1 offset 4800000 changed to 800000
  157. mtd parttion 2 offset 5800000 changed to 1000000
  158. mtd parttion 3 offset 6800000 changed to 1800000
  159. mtd parttion 4 offset 8800000 changed to 2000000
  160. mtd parttion 5 offset a800000 changed to 2800000
  161. mtd parttion 5 size 40000000 changed to 40200000
  162. mtd parttion 6 offset 4a800000 changed to 42a00000
  163. mtd parttion 7 offset ffffffffffffffff changed to 62a00000
  164. mtd parttion 7 size 0 changed to 9be00000
  165. NAND bbt detect factory Bad block at ffc00000
  166. NAND bbt detect factory Bad block at ff800000
  167. NAND bbt detect factory Bad block at ff400000
  168. NAND bbt detect factory Bad block at ff000000
  169. key start_blk=2036,end_blk=2047,aml_nand_key_init:684
  170. aml nand key valid addr: fea00000
  171. CONFIG_KEYSIZE=0x10000; KEYSIZE=0xfffc; bbt=0x1330; default_keyironment_size=0xeccc
  172. name=nand_key nand_key
  173. NAND bbt detect Bad block at 0
  174. NAND bbt detect factory Bad block at 5a00000
  175. Creating 7 MTD partitions on "nandnormal":
  176. 0x000000800000-0x000001000000 : "logo"
  177. 0x000001000000-0x000001800000 : "aml_logo"
  178. 0x000001800000-0x000002000000 : "recovery"
  179. 0x000002000000-0x000002800000 : "boot"
  180. 0x000002800000-0x000042c00000 : "system"
  181. NAND bbt detect factory Bad block at 5a00000
  182. 0x000042c00000-0x000062c00000 : "cache"
  183. 0x000062c00000-0x0000fd200000 : "userdata"
  184. nandnormal initialized ok
  185. detect mx chiprevD :0 and nand_type: 0
  186. nand_curr_device =1
  187. Using default environment
  188.  
  189. Saving Environment to SPI Flash...
  190. SPI BOOT,spi_saveenv : saveenv 97
  191. Erasing SPI flash...Writing to SPI flash...done
  192. Starting recovery...
  193. ## ANDROID Format IMAGE
  194. ## Booting kernel from Legacy Image at 82000000 ...
  195. Image Name: Linux-3.10.22
  196. Image Type: ARM Linux Kernel Image (lzma compressed)
  197. Data Size: 3426642 Bytes = 3.3 MiB
  198. Load Address: 80008000
  199. Entry Point: 80008000
  200. Verifying Checksum ... OK
  201. Ramdisk start addr = 0x82345800, len = 0x3ee800
  202. Flat device tree start addr = 0x82734000, len = 0x3ca2 magic=0xedfe0dd0
  203. Uncompressing Kernel Image ... OK
  204. machid from environment: 0x4e27
  205. EFUSE machid is not set.
  206. Using machid 0x4e27 from environment
  207. From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x843f6001
  208. Loading Ramdisk to 84007000, end 843f5800 ... OK
  209. Loading Device Tree to 84000000, end 84006ca1 ... OK
  210.  
  211. Starting kernel ...
  212.  
  213. [ 0.000000@0] Booting Linux on physical CPU 0x200
  214. [ 0.000000@0] Linux version 3.10.22-gd1a01b0-dirty (stane@stane-linux) (gcc version 4.7.3 20130205 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.02-01-20130221 - Linaro GCC 2013.02) ) #11 SMP PREEMPT Sat Mar 15 03:28:50 CET 2014
  215. [ 0.000000@0] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
  216. [ 0.000000@0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  217. [ 0.000000@0] Machine: Amlogic Meson6 platform, model: AMLOGIC
  218. [ 0.000000@0] physical memory start address is 0x80000000
  219. [ 0.000000@0] reserved_end is 8cffffff
  220. [ 0.000000@0] reserved 511M-512M 1M memory for firmware
  221. [ 0.000000@0] Total memory is 1024 MiB
  222. [ 0.000000@0] Reserved low memory from 0x85000000 to 0x8cffffff, size: 128 MiB
  223. [ 0.000000@0] ion_dev0(low) : 0x85100000 - 0x87100000 ( 32 MiB)
  224. [ 0.000000@0] mesonfb0(low) : 0x87100000 - 0x87900000 ( 8 MiB)
  225. [ 0.000000@0] mesonfb1(low) : 0x87900000 - 0x87a00000 ( 1 MiB)
  226. [ 0.000000@0] deinterlace0(low) : 0x87a00000 - 0x89600000 ( 28 MiB)
  227. [ 0.000000@0] mesonstream0(low) : 0x89600000 - 0x8a000000 ( 10 MiB)
  228. [ 0.000000@0] vdec0(low) : 0x8a000000 - 0x8c000000 ( 32 MiB)
  229. [ 0.000000@0] ppmgr0(low) : 0x8c000000 - 0x8d000000 ( 16 MiB)
  230. [ 0.000000@0] Ignore bootargs 'mem' param.
  231. [ 0.000000@0] Memory policy: ECC disabled, Data cache writealloc
  232. [ 0.000000@0] PERCPU: Embedded 7 pages/cpu @c1181000 s8192 r8192 d12288 u32768
  233. [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227616
  234. [ 0.000000@0] Kernel command line: root=/dev/cardblksd2 rw rootfstype=ext3 rootwait init=/init console=ttyS0,115200n8 nohlt vmalloc=256m mem=1024m logo=osd1,0x84100000,720p
  235. [ 0.000000@0] osd1:1
  236. [ 0.000000@0] 720p:6
  237. [ 0.000000@0] PID hash table entries: 4096 (order: 2, 16384 bytes)
  238. [ 0.000000@0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  239. [ 0.000000@0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  240. [ 0.000000@0] Memory: 80MB 303MB 512MB = 895MB total
  241. [ 0.000000@0] Memory: 894652k/894652k available, 21828k reserved, 278528K highmem
  242. [ 0.000000@0] Virtual kernel memory layout:
  243. [ 0.000000@0] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  244. [ 0.000000@0] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  245. [ 0.000000@0] vmalloc : 0xef800000 - 0xff000000 ( 248 MB)
  246. [ 0.000000@0] lowmem : 0xc0000000 - 0xef000000 ( 752 MB)
  247. [ 0.000000@0] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  248. [ 0.000000@0] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  249. [ 0.000000@0] .text : 0xc0008000 - 0xc08420f0 (8425 kB)
  250. [ 0.000000@0] .init : 0xc0843000 - 0xc0875000 ( 200 kB)
  251. [ 0.000000@0] .data : 0xc0876000 - 0xc08df200 ( 421 kB)
  252. [ 0.000000@0] .bss : 0xc08df200 - 0xc0973a8c ( 595 kB)
  253. [ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  254. [ 0.000000@0] Preemptible hierarchical RCU implementation.
  255. [ 0.000000@0] NR_IRQS:256
  256. [ 0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
  257. [ 0.000000@0] Global timer: MESON TIMER-A (c0893cc0) initialized
  258. [ 0.000000@0] Disable timerA
  259. [ 0.000000@0] Console: colour dummy device 80x30
  260. [ 0.000000@0] console [ttyS0] enabled
  261. [ 0.291268@0] Calibrating delay loop... 2387.14 BogoMIPS (lpj=11935744)
  262. [ 0.350050@0] pid_max: default: 32768 minimum: 301
  263. [ 0.352173@0] Security Framework initialized
  264. [ 0.356363@0] Mount-cache hash table entries: 512
  265. [ 0.364279@0] CPU: Testing write buffer coherency: ok
  266. [ 0.366471@0] CPU0: thread -1, cpu 0, socket 2, mpidr 80000200
  267. [ 0.371902@0] Local timer: MESON TIMER-B (c0893dc0) for CPU0 initialized
  268. [ 0.378521@0] Disable timerA
  269. [ 0.381378@0] Disable timerB
  270. [ 0.384249@0] Disable timerA
  271. [ 0.387257@0] Setting up static identity map for 0xc05f9760 - 0xc05f97b8
  272. [ 0.393958@0] L310 cache controller enabled
  273. [ 0.397958@0] l2x0: 8 ways, 2048 sets, CACHE_ID 0x4100a0c8, Cache size: 524288 B
  274. [ 0.405487@0] AUX_CTRL 0x3e460000, PERFETCH_CTRL 0x30000006, POWER_CTRL 0x00000000
  275. [ 0.413586@0] TAG_LATENCY 0x00000222, DATA_LATENCY 0x00000222
  276. [ 0.472292@1] CPU1: Booted secondary processor
  277. [ 0.531927@1] CPU1: thread -1, cpu 1, socket 2, mpidr 80000201
  278. [ 0.531942@1] Local timer: MESON TIMER-D (c0893fc0) for CPU1 initialized
  279. [ 0.532004@0] Brought up 2 CPUs
  280. [ 0.532010@0] SMP: Total of 2 processors activated (4780.85 BogoMIPS).
  281. [ 0.532013@0] CPU: All CPU(s) started in SVC mode.
  282. [ 0.532587@0] devtmpfs: initialized
  283. [ 0.537233@0] clkrate [ xtal ] : 24000000
  284. [ 0.537239@0] clkrate [ pll_sys ] : 1200000000
  285. [ 0.537244@0] clkrate [ pll_fixed ] : 2000000000
  286. [ 0.537248@0] clkrate [ pll_vid2 ] : 378000000
  287. [ 0.537251@0] clkrate [ pll_hpll ] : 378000000
  288. [ 0.537319@0] clkrate [ pll_ddr ] : 516000000
  289. [ 0.537323@0] clkrate [ a9_clk ] : 1200000000
  290. [ 0.537390@0] clkrate [ clk81 ] : 200000000
  291. [ 0.538456@0] pinctrl core: initialized pinctrl subsystem
  292. [ 0.538960@0] regulator-dummy: no parameters
  293. [ 0.539274@0] NET: Registered protocol family 16
  294. [ 0.556869@0] DMA: preallocated 4096 KiB pool for atomic coherent allocations
  295. [ 0.563165@0] amlogic_gpio gpio: Probed amlogic GPIO driver
  296. [ 0.563316@0] register lm device lm-root
  297. [ 0.563429@0] register lm device lm1
  298. [ 0.563529@0] register lm device lm0
  299. [ 0.563859@0] Init pinux probe!
  300. [ 0.564598@0] pinmux-m6 pinmux: Probed amlogic pinctrl driver
  301. [ 0.564790@0] -------early_init_dt_probe:38----------
  302. [ 0.564975@0] -------early_init_dt_init:115----------
  303. [ 0.564980@0] tv_init_module
  304. [ 0.564991@0] major number 254 for disp
  305.  
  306. [ 0.564993@0] vout_register_server
  307. [ 0.564995@0] register tv module server ok
  308.  
  309. [ 0.565103@0] major number 0 for disp
  310.  
  311. [ 0.565107@0] register tv module server ok
  312.  
  313. [ 0.565256@0] drivers/amlogic/i2c/aml_i2c.c : aml_i2c_init
  314. [ 0.565314@0] drivers/amlogic/i2c/aml_i2c.c : aml_i2c_probe
  315. [ 0.565321@0] plat->state_name:default
  316. [ 0.565334@0] master_no = 0, maseter_regs=f3100500
  317. [ 0.565576@0] aml-i2c i2c-AO: add adapter aml_i2c_adap0(ee812088)
  318. [ 0.565581@0] aml-i2c i2c-AO: aml i2c bus driver.
  319. [ 0.565709@0] drivers/amlogic/i2c/aml_i2c.c : aml_i2c_probe
  320. [ 0.565712@0] plat->state_name:default
  321. [ 0.565722@0] master_no = 1, maseter_regs=f1108500
  322. [ 0.565918@0] aml-i2c i2c-A: add adapter aml_i2c_adap1(ee812888)
  323. [ 0.565923@0] aml-i2c i2c-A: aml i2c bus driver.
  324. [ 0.566045@0] drivers/amlogic/i2c/aml_i2c.c : aml_i2c_probe
  325. [ 0.566049@0] plat->state_name:default
  326. [ 0.566057@0] master_no = 2, maseter_regs=f11087c0
  327. [ 0.566212@0] aml-i2c i2c-B: add adapter aml_i2c_adap2(ee813088)
  328. [ 0.566217@0] aml-i2c i2c-B: aml i2c bus driver.
  329. [ 0.566686@0] aml_pmu_init, 347
  330. [ 0.566783@0] hdmitx: system: amhdmitx_init
  331. [ 0.566786@0] hdmitx: system: Ver: 2014Jan5a
  332. [ 0.566843@0] hdmitx: system: amhdmitx_probe
  333. [ 0.567224@0] amhdmitx is using the pin GPIOD_5
  334. [ 0.567586@0] hdmitx: system: hw init
  335. [ 0.567595@0] HDMI: get brd phy data
  336. [ 0.567596@0] hdmi phy setting
  337. [ 0.567645@0] HDMI: get brd phy data
  338. [ 0.567646@0] hdmi phy setting
  339. [ 0.568175@0] hdmitx: system: reset intr mask
  340. [ 0.581983@0] hdmitx: system: irq 1
  341. [ 0.603452@0] hdmitx: system: irq 2
  342. [ 0.630348@0] bio: create slab <bio-0> at 0
  343. [ 0.631539@0] SCSI subsystem initialized
  344. [ 0.632205@0] usbcore: registered new interface driver usbfs
  345. [ 0.632331@0] usbcore: registered new interface driver hub
  346. [ 0.632487@0] usbcore: registered new device driver usb
  347. [ 0.632807@0] Linux video capture interface: v2.00
  348. [ 0.633595@0] TV mode 480cvbs selected.
  349. [ 0.633599@0] [0x1b7e] = 0xff
  350. [ 0.633601@0] [0x105f] = 0x0
  351. [ 0.633602@0] [0x109c] = 0x2001042d
  352. [ 0.633604@0] [0x109d] = 0x814d3928
  353. [ 0.633606@0] [0x109e] = 0x6b425012
  354. [ 0.633608@0] [0x109f] = 0x110
  355. [ 0.633609@0] [0x109c] = 0x1042d
  356. [ 0.633611@0] [0x1066] = 0x11943
  357. [ 0.633613@0] [0x1059] = 0x100
  358. [ 0.633615@0] [0x105f] = 0x80000
  359. [ 0.633616@0] [0x105f] = 0x88001
  360. [ 0.633618@0] [0x105f] = 0x80003
  361. [ 0.633619@0] [0x104a] = 0x101
  362. [ 0.633621@0] [0x1b54] = 0x12
  363. [ 0.633623@0] [0x1c0a] = 0x12
  364. [ 0.633624@0] [0x1b62] = 0x0
  365. [ 0.633626@0] [0x1b00] = 0x0
  366. [ 0.633628@0] [0x1b01] = 0x0
  367. [ 0.633629@0] [0x1b0a] = 0x5
  368. [ 0.633631@0] [0x1b0b] = 0x81
  369. [ 0.633632@0] [0x1b0e] = 0x3
  370. [ 0.633634@0] [0x1b0f] = 0x104
  371. [ 0.633636@0] [0x1b50] = 0x810b
  372. [ 0.633637@0] [0x1b68] = 0xf0
  373. [ 0.633639@0] [0x1b00] = 0x8
  374. [ 0.633640@0] [0x1b01] = 0x26
  375. [ 0.633642@0] [0x1b07] = 0x20
  376. [ 0.633643@0] [0x1b08] = 0x7
  377. [ 0.633645@0] [0x1b56] = 0x353
  378. [ 0.633646@0] [0x1c19] = 0xf3
  379. [ 0.633648@0] [0x1c1a] = 0x693
  380. [ 0.633649@0] [0x1c1b] = 0x12
  381. [ 0.633651@0] [0x1c1c] = 0x102
  382. [ 0.633653@0] [0x1c1d] = 0x13
  383. [ 0.633654@0] [0x1c1e] = 0x103
  384. [ 0.633656@0] [0x1b60] = 0x0
  385. [ 0.633657@0] [0x1b48] = 0x0
  386. [ 0.633659@0] [0x1b6e] = 0x2
  387. [ 0.633660@0] [0x1c18] = 0x4e01
  388. [ 0.633662@0] [0x1b7e] = 0x0
  389. [ 0.633663@0] [0x1b64] = 0x61
  390. [ 0.633665@0] [0x1b65] = 0x4061
  391. [ 0.633666@0] [0x1b66] = 0x5061
  392. [ 0.633668@0] [0x1b78] = 0x0
  393. [ 0.633669@0] [0x1b79] = 0x0
  394. [ 0.633671@0] [0x1b7a] = 0x0
  395. [ 0.633673@0] [0x1b7b] = 0x0
  396. [ 0.633674@0] [0x1b7c] = 0x0
  397. [ 0.633676@0] [0x1b7d] = 0x0
  398. [ 0.633677@0] [0x271a] = 0x5
  399. [ 0.633679@0] [0x1bfc] = 0x2000
  400. [ 0.633680@0] [0x1c0b] = 0x1111
  401. [ 0.633682@0] [0x1c0c] = 0x11
  402. [ 0.633683@0] [0x1b80] = 0x0
  403. [ 0.633685@0] [0x1b57] = 0x1
  404. [ 0.633687@0] tvoutc_setmode[317]
  405. [ 0.633690@0] mode is: 1
  406. [ 0.635858@0] call aml_pmu_probe_init in
  407. [ 0.636223@0] Advanced Linux Sound Architecture Driver Initialized.
  408. [ 0.636977@0] Bluetooth: Core ver 2.16
  409. [ 0.637170@0] NET: Registered protocol family 31
  410. [ 0.637173@0] Bluetooth: HCI device and connection manager initialized
  411. [ 0.637187@0] Bluetooth: HCI socket layer initialized
  412. [ 0.637194@0] Bluetooth: L2CAP socket layer initialized
  413. [ 0.637216@0] Bluetooth: SCO socket layer initialized
  414. [ 0.637695@0] cfg80211: Calling CRDA to update world regulatory domain
  415. [ 0.638825@0] Switching to clocksource Timer-E
  416. [ 1.058924@1] Disable timerD
  417. [ 1.061919@0] hdmitx: edid: edid failed
  418. [ 1.065663@0] hdmitx: edid: edid failed
  419. [ 1.069444@0] hdmitx: hpd: HPD deassert!
  420. [ 1.073515@0] hdmitx: cec: CEC not ready
  421. [ 1.087719@1] NET: Registered protocol family 2
  422. [ 1.088181@1] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
  423. [ 1.094023@1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
  424. [ 1.100502@1] TCP: Hash tables configured (established 8192 bind 8192)
  425. [ 1.107310@1] TCP: reno registered
  426. [ 1.110313@1] UDP hash table entries: 512 (order: 2, 16384 bytes)
  427. [ 1.116525@1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  428. [ 1.123153@1] NET: Registered protocol family 1
  429. [ 1.127588@1] Unpacking initramfs...
  430. [ 1.163848@1] Freeing initrd memory: 4024K (c4007000 - c43f5000)
  431. [ 1.171522@1] bounce pool size: 64 pages
  432. [ 1.225157@1] VFS: Disk quotas dquot_6.5.2
  433. [ 1.225622@1] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  434. [ 1.248538@1] fuse init (API version 7.22)
  435. [ 1.253777@1] msgmni has been set to 1211
  436. [ 1.256880@1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
  437. [ 1.259717@1] io scheduler noop registered
  438. [ 1.264093@1] io scheduler deadline registered
  439. [ 1.268701@1] io scheduler cfq registered (default)
  440. [ 1.945002@0] loop: module loaded
  441. [ 1.960255@0] tun: Universal TUN/TAP device driver, 1.6
  442. [ 1.960293@0] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  443. [ 1.968438@0] PPP generic driver version 2.4.2
  444. [ 1.974798@0] PPP BSD Compression module registered
  445. [ 1.975467@0] PPP Deflate Compression module registered
  446. [ 1.980687@0] PPP MPPE Compression module registered
  447. [ 1.985737@0] NET: Registered protocol family 24
  448. [ 1.990598@0] usbcore: registered new interface driver asix
  449. [ 1.996214@0] usbcore: registered new interface driver ax88179_178a
  450. [ 2.002487@0] usbcore: registered new interface driver cdc_ether
  451. [ 2.008353@0] usbcore: registered new interface driver net1080
  452. [ 2.014214@0] usbcore: registered new interface driver cdc_subset
  453. [ 2.020235@0] usbcore: registered new interface driver zaurus
  454. [ 2.026058@0] usbcore: registered new interface driver cdc_ncm
  455. [ 2.034530@0] usbcore: registered new interface driver cdc_acm
  456. [ 2.037274@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  457. [ 2.047491@0] usbcore: registered new interface driver usb-storage
  458. [ 2.052370@0] usbcore: registered new interface driver usbserial
  459. [ 2.060190@0] mousedev: PS/2 mouse device common for all mice
  460. [ 2.066175@0] i2c /dev entries driver
  461. [ 2.072734@0] usbcore: registered new interface driver uvcvideo
  462. [ 2.073025@0] USB Video Class driver (1.1.1)
  463. [ 2.077279@0] Bluetooth: HCI UART driver ver 2.2
  464. [ 2.083673@0] Bluetooth: HCI H4 protocol initialized
  465. [ 2.092316@0] usbcore: registered new interface driver usbhid
  466. [ 2.092551@0] usbhid: USB HID core driver
  467. [ 2.099207@0] zram: Created 1 device(s) ...
  468. [ 2.103084@0] ashmem: initialized
  469. [ 2.105359@0] logger: created 256K log 'log_main'
  470. [ 2.109247@0] logger: created 256K log 'log_events'
  471. [ 2.114539@0] logger: created 256K log 'log_radio'
  472. [ 2.118788@0] logger: created 256K log 'log_system'
  473. [ 2.123989@0] vout_init_module
  474. [ 2.126304@0] start init vout module
  475.  
  476. [ 2.131179@0] create vout attribute ok
  477.  
  478. [ 2.134472@0] ge2d_init
  479. [ 2.136400@0] ge2d_dev major:248
  480.  
  481. [ 2.142331@1] ge2d start monitor
  482.  
  483. [ 2.143087@1] osd_init
  484. [ 2.145517@1] Frame buffer memory assigned at phy:0x87100000, vir:0xf0000000, size=8192K
  485. [ 2.153433@1] ge2d workqueue monitor start
  486.  
  487. [ 2.157576@1] init fbdev bpp is :32
  488.  
  489. [ 2.161123@1] ---------------clear framebuffer0 memory
  490.  
  491. [ 2.185411@0] Frame buffer memory assigned at phy:0x87900000, vir:0xefe00000, size=1024K
  492. [ 2.187859@0] ---------------clear framebuffer1 memory
  493.  
  494. [ 2.218666@0] osd probe ok
  495.  
  496. [ 2.219093@0] vout2_init_module enter
  497. [ 2.225393@0] amlvideo-000: V4L2 device registered as video10
  498. [ 2.228264@0] ionvideo-000: V4L2 device registered as video13
  499. [ 2.231236@0] Video Technology Magazine Ion Video Capture Board ver 1.0 successfully loaded.
  500. [ 2.244499@0] keys===========================================
  501. [ 2.245392@0] keys_devno=f400000
  502. [ 2.249336@0] securitykey: device aml_keys created
  503. [ 2.253475@0] amlkeys=0
  504. [ 2.256136@0] platform_driver_register--aml_keys_driver--------------------
  505. [ 2.263491@0] set uart_ao pinmux use pinctrl subsystem
  506. [ 2.267867@0] P_AO_RTI_PIN_MUX_REG:5861
  507. [ 2.271723@0] start uart_ao_ttyS0:(irq = 122)
  508. [ 2.276187@0] register uart_ao ok
  509. [ 2.279843@0] start uart_a_ttyS1:(irq = 58)
  510. [ 2.283596@0] register uart_a ok
  511. [ 2.287246@0] start uart_d_ttyS4:(irq = 126)
  512. [ 2.290957@0] register uart_d ok
  513. [ 2.294605@0] dwc_otg: version 3.10a 21-DEC-2012
  514. [ 2.298824@0] dwc_otg_driver_probe NOT match
  515. [ 2.303130@0] usb1: type: 1, speed: 0, config: 0, dma: 0, id: 1, phy: f1108420, ctrl: f32c0000
  516. [ 2.811647@0] USB (1) use clock source: XTAL input
  517. [ 3.012809@0] Core Release: 2.94a
  518. [ 3.012846@0] Setting default values for core params
  519. [ 3.415619@0] Using Buffer DMA mode
  520. [ 3.415643@0] OTG VER PARAM: 1, OTG VER FLAG: 1
  521. [ 3.417980@0] Working on port type = HOST
  522. [ 3.422071@0] dwc_otg lm1: DWC OTG Controller
  523. [ 3.426332@0] dwc_otg lm1: new USB bus registered, assigned bus number 1
  524. [ 3.433052@0] dwc_otg lm1: irq 63, io mem 0x00000000
  525. [ 3.437968@0] Init: Port Power? op_state=1
  526. [ 3.442047@0] Init1: Power Port (0)
  527. [ 3.446594@0] hub 1-0:1.0: USB hub found
  528. [ 3.449431@0] hub 1-0:1.0: 1 port detected
  529. [ 3.453870@0] usb0: type: 0, speed: 0, config: 0, dma: 0, id: 0, phy: f1108400, ctrl: f3240000
  530. [ 3.651941@0] Indeed it is in host mode hprt0 = 00021501
  531. [ 3.672389@1] Core Release: 2.94a
  532. [ 3.672421@1] Setting default values for core params
  533. [ 3.841918@0] usb 1-1: new high-speed USB device number 2 using dwc_otg
  534. [ 3.843116@0] Indeed it is in host mode hprt0 = 00001101
  535. [ 4.045811@0] hub 1-1:1.0: USB hub found
  536. [ 4.046157@0] hub 1-1:1.0: 4 ports detected
  537. [ 4.075030@1] Using Buffer DMA mode
  538. [ 4.075059@1] OTG VER PARAM: 1, OTG VER FLAG: 1
  539. [ 4.077393@1] Working on port type = OTG
  540. [ 4.081296@1] Current port type: SLAVE
  541. [ 4.085136@1] dwc_otg lm0: DWC OTG Controller
  542. [ 4.089392@1] dwc_otg lm0: new USB bus registered, assigned bus number 2
  543. [ 4.096108@1] dwc_otg lm0: irq 62, io mem 0x00000000
  544. [ 4.102077@1] hub 2-0:1.0: USB hub found
  545. [ 4.104940@1] hub 2-0:1.0: 1 port detected
  546. [ 4.109124@1] Dedicated Tx FIFOs mode
  547. [ 4.114390@1] using timer detect id change, ee9a6800
  548. [ 4.117950@1] Amlogic nand flash Kernel driver, Version K1.06.015 (c) 2010 Amlogic Inc.
  549. [ 4.127262@1] ####Version of Uboot must be newer than U1.06.011!!!!!
  550. [ 4.132138@1] ===========================================m3_nand_probe:1230,nand device tree ok,dev-name:nand1
  551. [ 4.142027@1] m3_get_nand_platform:1682,find enable pad finished
  552. [ 4.147960@1] m3_get_nand_platform:1695,find busy_pad finished
  553. [ 4.153807@1] m3_get_nand_platform:1707,find timming_mode finished
  554. [ 4.159940@1] m3_get_nand_platform:1719,find bch_mode finished
  555. [ 4.165769@1] m3_get_nand_platform:1731,find plane_modefinished
  556. [ 4.171671@1] m3_get_nand_platform:1787,parse dts
  557. [ 4.176355@1] chip->controller=c094a4a4
  558. [ 4.180166@1] ###plat->platform_nand_data.chip.nr_chips =2
  559. [ 4.185649@1] init bus_cycle=17, bus_timing=10, start_cycle=10, end_cycle=10,system=5.0ns
  560. [ 4.194017@1] No NAND device found
  561. [ 4.197341@1] NAND device id: 2c 68 4 4a a9 0
  562. [ 4.201610@1] NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron C revision NAND 4GiB MT29F32G-C)
  563. [ 4.216810@1] 1 NAND chips detected
  564. [ 4.216847@1] onfi timing mode set failed: 49
  565. [ 4.219043@1] aml_nand_init auto detect RB pin here and por_cfg:3fc
  566. [ 4.225262@1] aml_nand_init detect with RB pin here
  567. [ 4.230106@1] #####aml_nand_init, with RB pins and chip->chip_delay:20
  568. [ 4.236633@1] bus_cycle=11, bus_timing=10, start_cycle=10, end_cycle=10,system=5.0ns
  569. [ 4.244355@1] oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH30_1K_MODE
  570. [ 4.254853@1] aml_chip->oob_fill_cnt =0,aml_chip->oob_size =224,bch_bytes =54
  571. [ 4.261973@1] oob layout use nand base oob layout oobsize = 16,oobmul =2,mtd->oobsize =448,aml_chip->oob_size =224
  572. [ 4.291177@1] aml nand env valid addr: 10000
  573. [ 4.321580@1] nand key: nand_key_probe.
  574. [ 4.321614@1] NAND bbt detect factory Bad block at ffc00000
  575. [ 4.325597@1] NAND bbt detect factory Bad block at ff800000
  576. [ 4.331314@1] NAND bbt detect factory Bad block at ff400000
  577. [ 4.337050@1] NAND bbt detect factory Bad block at ff000000
  578. [ 4.342780@1] key start_blk=2036,end_blk=2047,aml_nand_key_init:595
  579. [ 4.358806@1] aml nand key valid addr: fea00000
  580. [ 4.358875@1] i=0,register --- nand_key
  581. [ 4.365092@1] NAND bbt detect factory Bad block at 5a00000
  582. [ 4.367291@1] Creating 7 MTD partitions on "C revision NAND 4GiB MT29F32G-C":
  583. [ 4.376246@1] 0x000000800000-0x000001000000 : "logo"
  584. [ 4.386343@1] 0x000001000000-0x000001800000 : "aml_logo"
  585. [ 4.393505@1] 0x000001800000-0x000002000000 : "recovery"
  586. [ 4.399001@1] 0x000002000000-0x000002800000 : "boot"
  587. [ 4.404528@1] 0x000002800000-0x000042a00000 : "system"
  588. [ 4.404592@1] NAND bbt detect factory Bad block at 5a00000
  589. [ 4.413681@1] 0x000042a00000-0x000062a00000 : "cache"
  590. [ 4.419894@1] 0x000062a00000-0x0000fe800000 : "userdata"
  591. [ 4.425629@1] ,
  592. ,8+ethernet_driver probe!
  593. [ 4.427974@1] Please config savepowermode.
  594. [ 4.430943@1] Please config reset_pin_enable.
  595. [ 4.437173@1] Please config reset_delay.
  596. [ 4.439190@1] Please config reset_pin.
  597. [ 4.442960@1] ethernetinit(dbg[c08be44c]=1)
  598. [ 4.447123@1] ethernet base addr is f3610000
  599. [ 4.451354@1] write mac add to:edeff4c8: c6 44 85 10 23 ee |.D.#.|
  600. [ 4.466864@1] libphy: AMLMAC MII Bus: probed
  601. [ 4.466915@1] eth0: PHY ID 0007c0f1 at 1 IRQ -1 (0:01) active
  602. [ 4.472003@1] Amlogic A/V streaming port init
  603. [ 4.494563@1] init vdec memsource -1979711488->-1946157057
  604. [ 4.497150@1] regist mpeg12 codec profile
  605. [ 4.500498@1] regist mpeg4 codec profile
  606. [ 4.502391@1] amvdec_vc1 module init
  607. [ 4.506280@1] regist vc1 codec profile
  608. [ 4.509608@1] amvdec_h264 module init
  609. [ 4.513644@1] regist h264 codec profile
  610. [ 4.517415@1] regist mjpeg codec profile
  611. [ 4.520977@1] amvdec_real module init
  612. [ 4.525102@1] regist real codec profile
  613. [ 4.535015@1] efuse===========================================
  614. [ 4.537595@1] efuse: device efuse created
  615. [ 4.541217@1] efuse--------------------------------------------
  616. [ 4.545210@1] SARADC Driver init.
  617. [ 4.548921@1] __saradc_probe__
  618. [ 4.692017@1] saradc calibration: ref_val = 512
  619. [ 4.692045@1] saradc calibration: ref_nominal = 512
  620. [ 4.695761@1] saradc calibration: coef = 4161
  621. [ 4.700486@1] Remote Driver
  622. [ 4.703023@1] Remote platform_data g_remote_base=f3100480
  623. [ 4.708585@1] input: aml_keypad as /devices/platform/meson-remote/input/input0
  624. [ 4.716608@1] Remote date_valye======0,status == 8915f20
  625. [ 4.720808@1] remote config major:241
  626.  
  627. [ 4.726968@1] physical address:0xad824000
  628. [ 4.729215@1] ADC Keypad Driver init.
  629. [ 4.732284@1] ==kp_probe==
  630. [ 4.734844@1] chan #4 used for ADC key
  631. [ 4.738554@1] menu key(139) registed.
  632. [ 4.742248@1] vol- key(114) registed.
  633. [ 4.745852@1] vol+ key(115) registed.
  634. [ 4.749490@1] back key(158) registed.
  635. [ 4.753154@1] home key(102) registed.
  636. [ 4.757217@1] input: adc_keypad as /devices/platform/adc_keypad.3/input/input1
  637. [ 4.764490@1] adc keypad register input device completed.
  638.  
  639. [ 4.769473@1] adc keypad major:240
  640.  
  641. [ 4.775866@1] Meson KeyInput init
  642. [ 4.776417@1] Key 116 registed.
  643. [ 4.779805@1] input: key_input as /devices/platform/key_input.4/input/input2
  644. [ 4.786898@1] Meson KeyInput register RTC interrupt
  645. [ 4.791112@1] Meson KeyInput major=238
  646. [ 4.803026@1] i2c-core: driver [lis3dh_acc] using legacy suspend method
  647. [ 4.804019@1] i2c-core: driver [lis3dh_acc] using legacy resume method
  648. [ 4.811111@1] i2c-core: driver [bma222] using legacy suspend method
  649. [ 4.816832@1] i2c-core: driver [bma222] using legacy resume method
  650. [ 4.824678@1] i2c-core: driver [dmard06] using legacy suspend method
  651. [ 4.829275@1] i2c-core: driver [dmard06] using legacy resume method
  652. [ 4.838687@1] i2c-core: driver [dmard10] using legacy suspend method
  653. [ 4.841859@1] i2c-core: driver [dmard10] using legacy resume method
  654. [ 4.850201@1] stk831x_init
  655. [ 4.851157@1] mxc622x accelerometer driver: init
  656. [ 4.857503@1] i2c-core: driver [mxc622x] using legacy suspend method
  657. [ 4.861732@1] i2c-core: driver [mxc622x] using legacy resume method
  658. [ 4.871001@1] i2c-core: driver [elan_epl6814] using legacy suspend method
  659. [ 4.874796@1] i2c-core: driver [elan_epl6814] using legacy resume method
  660. [ 4.883398@1] i2c-core: driver [LTR501] using legacy suspend method
  661. [ 4.887892@1] i2c-core: driver [LTR501] using legacy resume method
  662. [ 4.896973@1] spi_nor_init
  663. [ 4.897522@1] amlogic_spi_nor_probe:
  664. [ 4.900114@1] amlogic_spi->state_name:default
  665. [ 4.906566@1] AMLOGIC_SPI_NOR cc000000.spi: master is unqueued, this is deprecated
  666. [ 4.912419@1] spi_nor_probe
  667. [ 4.914776@1] check_storage_device : spi boot_device_flag : 0
  668. [ 4.920628@1] spi_nor apollospi:32766: mx25l4006e (512 Kbytes)
  669. [ 4.928481@1] Creating 2 MTD partitions on "apollospi:32766":
  670. [ 4.932099@1] 0x000000000000-0x000000060000 : "bootloader"
  671. [ 4.941449@1] 0x000000060000-0x000000068000 : "ubootenv"
  672. [ 4.948197@1] amlogic_spi_nor_probe over
  673. [ 4.950027@1] mmc driver version: 1.05, 2014-01-16: sdhc eMMC run at 8bit@50MHz ok
  674. [ 4.955423@1] host->base f1108c20
  675. [ 4.957598@1] pdata->caps 7
  676. [ 4.960338@1] pdata->caps2 0
  677. [ 4.963320@1] get property: port, value:0x00000001
  678. [ 4.969712@1] get property: ocr_avail, value:0x00200000
  679. [ 4.976237@1] get property: f_min, value:0x000493e0
  680. [ 4.982874@1] get property: f_max, value:0x02faf080
  681. [ 4.989242@1] get property: f_max_w, value:0x02faf080
  682. [ 4.995765@1] get property: max_req_size, value:0x00020000
  683. [ 5.002274@1] get property: irq_in, value:0x00000005
  684. [ 5.008772@1] get property: irq_out, value:0x00000006
  685. [ 5.015418@1] get property: power_level, value:0x00000000
  686. [ 5.021798@1] get property: gpio_cd, str:CARD_6
  687. [ 5.027798@1] get property: gpio_power, str:CARD_8
  688. [ 5.033779@1] get property: pinname, str:sd
  689. [ 5.039413@1] get property: card_type, value:0x00000005
  690. [ 5.046052@1] get property: gpio_dat3, str:CARD_3
  691. [ 5.051945@1] normal card in
  692. [ 5.091996@0] sd: mmc_rescan_try_freq: trying to init card at 400000 Hz
  693. [ 5.618975@1] sd: new SDHC card at address 8e92, clock 25000000, 4-bit-bus-width
  694. [ 5.621506@1] mmcblk0: sd:8e92 SD04G 3.69 GiB
  695. [ 5.622000@0] [aml_sdio_probe] aml_sdio_probe() success!
  696. [ 5.624233@0] [dsp]DSP start addr 0xc5000000
  697. [ 5.624277@0] [dsp]register dsp to char divece(232)
  698. [ 5.642009@0] aml_rtc_init...
  699. [ 5.643778@1] aml_rtc rtc.0: rtc core: registered aml_rtc as rtc0
  700. [ 5.648773@1] mmcblk0: p1
  701. [ 5.657956@1] [AXP]call axp_battery_init, ret = 0
  702. [ 5.667708@1] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
  703. [ 5.670240@1] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
  704. [ 5.679683@1] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
  705. [ 5.685762@1] platform reg-20-cs-buck2: Driver reg-20-cs-buck2 requests probe deferral
  706. [ 5.693772@1] platform reg-20-cs-buck3: Driver reg-20-cs-buck3 requests probe deferral
  707. [ 5.701487@1] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
  708. [ 5.709795@1] [AML_PMU]call aml_pmu_battery_init, ret = 0
  709. [ 5.714931@1] [RN5T618]call rn5t618_battery_init, ret = 0
  710. [ 5.720224@1] vdin_drv_init: major 237
  711. [ 5.724424@1] amvdec_656in module: init.
  712. [ 5.727547@1] amvdec_656in_init_module:major 236
  713. [ 5.737019@1] amvdec_656in probe ok.
  714. [ 5.746961@1] wifi_power power_gpio is 24
  715. [ 5.746994@1] wifi_dev_probe : there is no wifi_power_on_pin2 setup in DTS file!
  716. [ 5.755748@1] amlogic rfkill init
  717. [ 5.772716@1] usbcore: registered new interface driver snd-usb-audio
  718. [ 5.783991@1] enter dummy_codec_audio_probe
  719. [ 5.784529@1] soc-audio soc-audio: ASoC: machine AML-DUMMY-CODEC should use snd_soc_register_card()
  720. [ 5.794135@1] rtd ed854810
  721. [ 5.794345@1] cpu_dai eeb23f00
  722. [ 5.797470@1] codec_dai eeb23c00
  723. [ 5.801280@1] aml-pcm 0:playback preallocate_dma_buffer: area=f0d01000, addr=ad8c0000, size=131072
  724. [ 5.810864@1] iec958 0: preallocate dma buffer start=f0d23000, size=80000
  725. [ 5.817231@1] aml-pcm 1:capture preallocate_dma_buffer: area=f0da4000, addr=aeae0000, size=65536
  726. [ 5.825428@1] soc-audio soc-audio: dummy_codec <-> aml-dai0 mapping ok
  727. [ 5.839144@1] =dummy_codec_device_init==,dummy_codec_audio init done
  728. [ 5.841511@1] GACT probability NOT on
  729. [ 5.843550@1] Mirror/redirect action on
  730. [ 5.847326@1] u32 classifier
  731. [ 5.850183@1] Actions configured
  732. [ 5.853896@1] Netfilter messages via NETLINK v0.30.
  733. [ 5.858671@1] nf_conntrack version 0.5.0 (14041 buckets, 56164 max)
  734. [ 5.866049@1] ctnetlink v0.93: registering with nfnetlink.
  735. [ 5.870399@1] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
  736. [ 5.879248@1] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
  737. [ 5.884691@1] xt_time: kernel timezone is -0000
  738. [ 5.888245@1] ip_tables: (C) 2000-2006 Netfilter Core Team
  739. [ 5.893707@1] arp_tables: (C) 2002 David S. Miller
  740. [ 5.898258@1] TCP: cubic registered
  741. [ 5.905292@1] NET: Registered protocol family 10
  742. [ 5.907233@1] mip6: Mobile IPv6
  743. [ 5.909416@1] ip6_tables: (C) 2000-2006 Netfilter Core Team
  744. [ 5.917064@1] sit: IPv6 over IPv4 tunneling driver
  745. [ 5.926559@1] NET: Registered protocol family 17
  746. [ 5.926669@1] NET: Registered protocol family 15
  747. [ 5.930258@1] Bridge firewalling registered
  748. [ 5.936207@1] Bluetooth: RFCOMM TTY layer initialized
  749. [ 5.939390@1] Bluetooth: RFCOMM socket layer initialized
  750. [ 5.944810@1] Bluetooth: RFCOMM ver 1.11
  751. [ 5.948548@1] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  752. [ 5.954063@1] Bluetooth: BNEP filters: protocol multicast
  753. [ 5.959408@1] Bluetooth: BNEP socket layer initialized
  754. [ 5.964535@1] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  755. [ 5.970600@1] Bluetooth: HIDP socket layer initialized
  756. [ 5.975946@1] NET: Registered protocol family 35
  757. [ 5.980691@1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
  758. [ 5.988147@1] Registering SWP/SWPB emulation handler
  759. [ 5.993090@1] enter meson_pm_init
  760. [ 5.996583@1] enter meson_pm_probe!
  761. [ 5.999849@1] meson_pm_probe done !
  762. [ 6.008328@0] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
  763. [ 6.011142@0] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
  764. [ 6.019738@0] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
  765. [ 6.026631@0] platform reg-20-cs-buck2: Driver reg-20-cs-buck2 requests probe deferral
  766. [ 6.034522@0] platform reg-20-cs-buck3: Driver reg-20-cs-buck3 requests probe deferral
  767. [ 6.042393@0] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
  768. [ 6.053184@1] file system registered
  769. [ 6.067201@1] android_usb gadget: Mass Storage Function, version: 2009/09/11
  770. [ 6.068631@1] android_usb gadget: Number of LUNs=1
  771. [ 6.074635@1] lun0: LUN: removable file: (no medium)
  772. [ 6.080904@1] android_usb gadget: android_usb ready
  773. [ 6.084237@1] aml_rtc rtc.0: setting system clock to 1970-01-01 00:00:18 UTC (18)
  774. [ 6.090790@1] ### dt-test ### No testcase data in device tree; not running tests
  775. [ 6.098648@1] don't findmatch init-data
  776. [ 6.102202@1] cpu freq limited to 1200000000
  777. [ 6.106376@1] ------------[ cut here ]------------
  778. [ 6.111165@1] WARNING: at kernel/smp.c:382 smp_call_function_many+0x84/0x2c4()
  779. [ 6.118352@1] Modules linked in:
  780. [ 6.121568@1] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.10.22 #11
  781. [ 6.127844@1] [<c0014b18>] (unwind_backtrace+0x0/0xf8) from [<c0011c20>] (show_stack+0x10/0x14)
  782. [ 6.136507@1] [<c0011c20>] (show_stack+0x10/0x14) from [<c002a07c>] (warn_slowpath_common+0x4c/0x6c)
  783. [ 6.145616@1] [<c002a07c>] (warn_slowpath_common+0x4c/0x6c) from [<c002a0b8>] (warn_slowpath_null+0x1c/0x24)
  784. [ 6.155424@1] [<c002a0b8>] (warn_slowpath_null+0x1c/0x24) from [<c0070378>] (smp_call_function_many+0x84/0x2c4)
  785. [ 6.165492@1] [<c0070378>] (smp_call_function_many+0x84/0x2c4) from [<c0070744>] (smp_call_function+0x34/0x64)
  786. [ 6.175473@1] [<c0070744>] (smp_call_function+0x34/0x64) from [<c001b4d8>] (clk_set_rate_a9+0x94/0xd4)
  787. [ 6.184760@1] [<c001b4d8>] (clk_set_rate_a9+0x94/0xd4) from [<c001b8a4>] (meson_clk_set_rate+0xa0/0x184)
  788. [ 6.194221@1] [<c001b8a4>] (meson_clk_set_rate+0xa0/0x184) from [<c001ba2c>] (clk_set_rate+0xa4/0xc0)
  789. [ 6.203427@1] [<c001ba2c>] (clk_set_rate+0xa4/0xc0) from [<c038997c>] (meson_cpufreq_target_locked.isra.4+0x108/0x224)
  790. [ 6.214101@1] [<c038997c>] (meson_cpufreq_target_locked.isra.4+0x108/0x224) from [<c0389abc>] (meson_cpufreq_target+0x24/0x3c)
  791. [ 6.225471@1] [<c0389abc>] (meson_cpufreq_target+0x24/0x3c) from [<c0302648>] (__cpufreq_driver_target+0x50/0x74)
  792. [ 6.235718@1] [<c0302648>] (__cpufreq_driver_target+0x50/0x74) from [<c030819c>] (dbs_check_cpu+0x20c/0x220)
  793. [ 6.245522@1] [<c030819c>] (dbs_check_cpu+0x20c/0x220) from [<c0308a9c>] (cpufreq_governor_dbs+0x888/0x8dc)
  794. [ 6.255241@1] [<c0308a9c>] (cpufreq_governor_dbs+0x888/0x8dc) from [<c0302800>] (__cpufreq_governor+0x70/0xf0)
  795. [ 6.265223@1] [<c0302800>] (__cpufreq_governor+0x70/0xf0) from [<c0302aa0>] (__cpufreq_set_policy+0x1b0/0x1d0)
  796. [ 6.275205@1] [<c0302aa0>] (__cpufreq_set_policy+0x1b0/0x1d0) from [<c0303390>] (cpufreq_add_dev_interface+0x208/0x254)
  797. [ 6.285968@1] [<c0303390>] (cpufreq_add_dev_interface+0x208/0x254) from [<c0303714>] (cpufreq_add_dev+0x338/0x44c)
  798. [ 6.296303@1] [<c0303714>] (cpufreq_add_dev+0x338/0x44c) from [<c0236914>] (subsys_interface_register+0x80/0xc4)
  799. [ 6.306456@1] [<c0236914>] (subsys_interface_register+0x80/0xc4) from [<c0303d00>] (cpufreq_register_driver+0xa0/0x198)
  800. [ 6.317220@1] [<c0303d00>] (cpufreq_register_driver+0xa0/0x198) from [<c085d654>] (meson_cpufreq_probe+0x200/0x278)
  801. [ 6.327636@1] [<c085d654>] (meson_cpufreq_probe+0x200/0x278) from [<c023896c>] (platform_drv_probe+0x14/0x18)
  802. [ 6.337530@1] [<c023896c>] (platform_drv_probe+0x14/0x18) from [<c0237798>] (driver_probe_device+0xbc/0x1f8)
  803. [ 6.347337@1] [<c0237798>] (driver_probe_device+0xbc/0x1f8) from [<c023793c>] (__driver_attach+0x68/0x8c)
  804. [ 6.356884@1] [<c023793c>] (__driver_attach+0x68/0x8c) from [<c0235f2c>] (bus_for_each_dev+0x4c/0x8c)
  805. [ 6.366086@1] [<c0235f2c>] (bus_for_each_dev+0x4c/0x8c) from [<c0236f28>] (bus_add_driver+0xcc/0x234)
  806. [ 6.375286@1] [<c0236f28>] (bus_add_driver+0xcc/0x234) from [<c0237e88>] (driver_register+0xa0/0x13c)
  807. [ 6.384487@1] [<c0237e88>] (driver_register+0xa0/0x13c) from [<c0238c10>] (platform_driver_probe+0x18/0x9c)
  808. [ 6.394209@1] [<c0238c10>] (platform_driver_probe+0x18/0x9c) from [<c0008554>] (do_one_initcall+0x94/0x144)
  809. [ 6.403934@1] [<c0008554>] (do_one_initcall+0x94/0x144) from [<c0843b5c>] (kernel_init_freeable+0xfc/0x1c8)
  810. [ 6.413658@1] [<c0843b5c>] (kernel_init_freeable+0xfc/0x1c8) from [<c05e9c18>] (kernel_init+0x8/0xe4)
  811. [ 6.422856@1] [<c05e9c18>] (kernel_init+0x8/0xe4) from [<c000e198>] (ret_from_fork+0x14/0x3c)
  812. [ 6.431355@1] ---[ end trace 5df819231a7e30d7 ]---
  813. [ 6.436129@1] ------------[ cut here ]------------
  814. [ 6.440908@1] WARNING: at kernel/smp.c:244 smp_call_function_single+0x98/0x1c0()
  815. [ 6.448278@1] Modules linked in:
  816. [ 6.451493@1] CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W 3.10.22 #11
  817. [ 6.458705@1] [<c0014b18>] (unwind_backtrace+0x0/0xf8) from [<c0011c20>] (show_stack+0x10/0x14)
  818. [ 6.467385@1] [<c0011c20>] (show_stack+0x10/0x14) from [<c002a07c>] (warn_slowpath_common+0x4c/0x6c)
  819. [ 6.476496@1] [<c002a07c>] (warn_slowpath_common+0x4c/0x6c) from [<c002a0b8>] (warn_slowpath_null+0x1c/0x24)
  820. [ 6.486304@1] [<c002a0b8>] (warn_slowpath_null+0x1c/0x24) from [<c00701cc>] (smp_call_function_single+0x98/0x1c0)
  821. [ 6.496546@1] [<c00701cc>] (smp_call_function_single+0x98/0x1c0) from [<c0070744>] (smp_call_function+0x34/0x64)
  822. [ 6.506700@1] [<c0070744>] (smp_call_function+0x34/0x64) from [<c001b4d8>] (clk_set_rate_a9+0x94/0xd4)
  823. [ 6.515988@1] [<c001b4d8>] (clk_set_rate_a9+0x94/0xd4) from [<c001b8a4>] (meson_clk_set_rate+0xa0/0x184)
  824. [ 6.525449@1] [<c001b8a4>] (meson_clk_set_rate+0xa0/0x184) from [<c001ba2c>] (clk_set_rate+0xa4/0xc0)
  825. [ 6.534653@1] [<c001ba2c>] (clk_set_rate+0xa4/0xc0) from [<c038997c>] (meson_cpufreq_target_locked.isra.4+0x108/0x224)
  826. [ 6.545327@1] [<c038997c>] (meson_cpufreq_target_locked.isra.4+0x108/0x224) from [<c0389abc>] (meson_cpufreq_target+0x24/0x3c)
  827. [ 6.556698@1] [<c0389abc>] (meson_cpufreq_target+0x24/0x3c) from [<c0302648>] (__cpufreq_driver_target+0x50/0x74)
  828. [ 6.566942@1] [<c0302648>] (__cpufreq_driver_target+0x50/0x74) from [<c030819c>] (dbs_check_cpu+0x20c/0x220)
  829. [ 6.576749@1] [<c030819c>] (dbs_check_cpu+0x20c/0x220) from [<c0308a9c>] (cpufreq_governor_dbs+0x888/0x8dc)
  830. [ 6.586470@1] [<c0308a9c>] (cpufreq_governor_dbs+0x888/0x8dc) from [<c0302800>] (__cpufreq_governor+0x70/0xf0)
  831. [ 6.596451@1] [<c0302800>] (__cpufreq_governor+0x70/0xf0) from [<c0302aa0>] (__cpufreq_set_policy+0x1b0/0x1d0)
  832. [ 6.606434@1] [<c0302aa0>] (__cpufreq_set_policy+0x1b0/0x1d0) from [<c0303390>] (cpufreq_add_dev_interface+0x208/0x254)
  833. [ 6.617196@1] [<c0303390>] (cpufreq_add_dev_interface+0x208/0x254) from [<c0303714>] (cpufreq_add_dev+0x338/0x44c)
  834. [ 6.627527@1] [<c0303714>] (cpufreq_add_dev+0x338/0x44c) from [<c0236914>] (subsys_interface_register+0x80/0xc4)
  835. [ 6.637683@1] [<c0236914>] (subsys_interface_register+0x80/0xc4) from [<c0303d00>] (cpufreq_register_driver+0xa0/0x198)
  836. [ 6.648445@1] [<c0303d00>] (cpufreq_register_driver+0xa0/0x198) from [<c085d654>] (meson_cpufreq_probe+0x200/0x278)
  837. [ 6.658862@1] [<c085d654>] (meson_cpufreq_probe+0x200/0x278) from [<c023896c>] (platform_drv_probe+0x14/0x18)
  838. [ 6.668757@1] [<c023896c>] (platform_drv_probe+0x14/0x18) from [<c0237798>] (driver_probe_device+0xbc/0x1f8)
  839. [ 6.678565@1] [<c0237798>] (driver_probe_device+0xbc/0x1f8) from [<c023793c>] (__driver_attach+0x68/0x8c)
  840. [ 6.688113@1] [<c023793c>] (__driver_attach+0x68/0x8c) from [<c0235f2c>] (bus_for_each_dev+0x4c/0x8c)
  841. [ 6.697313@1] [<c0235f2c>] (bus_for_each_dev+0x4c/0x8c) from [<c0236f28>] (bus_add_driver+0xcc/0x234)
  842. [ 6.706514@1] [<c0236f28>] (bus_add_driver+0xcc/0x234) from [<c0237e88>] (driver_register+0xa0/0x13c)
  843. [ 6.715716@1] [<c0237e88>] (driver_register+0xa0/0x13c) from [<c0238c10>] (platform_driver_probe+0x18/0x9c)
  844. [ 6.725437@1] [<c0238c10>] (platform_driver_probe+0x18/0x9c) from [<c0008554>] (do_one_initcall+0x94/0x144)
  845. [ 6.735158@1] [<c0008554>] (do_one_initcall+0x94/0x144) from [<c0843b5c>] (kernel_init_freeable+0xfc/0x1c8)
  846. [ 6.744882@1] [<c0843b5c>] (kernel_init_freeable+0xfc/0x1c8) from [<c05e9c18>] (kernel_init+0x8/0xe4)
  847. [ 6.754082@1] [<c05e9c18>] (kernel_init+0x8/0xe4) from [<c000e198>] (ret_from_fork+0x14/0x3c)
  848. [ 6.762583@1] ---[ end trace 5df819231a7e30d8 ]---
  849. [ 6.767904@0] cpu freq limited to 1200000000
  850. [ 6.767967@1] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
  851. [ 6.768037@1] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
  852. [ 6.768079@1] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
  853. [ 6.768117@1] platform reg-20-cs-buck2: Driver reg-20-cs-buck2 requests probe deferral
  854. [ 6.768153@1] platform reg-20-cs-buck3: Driver reg-20-cs-buck3 requests probe deferral
  855. [ 6.768189@1] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
  856. [ 6.819205@1] cpu freq limited to 1200000000
  857. [ 6.823606@1] hdmitx: cec: CEC init
  858. [ 6.826892@1] hdmitx: cec: CEC task process
  859. [ 6.830766@1] input: cec_input as /devices/virtual/input/input3
  860. [ 6.837095@1] hdmitx: cec: hdmitx_device->cec_init_ready:0x1
  861. [ 6.842152@1] ALSA device list:
  862. [[ 6.861924@1] Changing uart_ao_ttyS0: baud from 0 to 115200
  863. [ 6.882141@0] Freeing unused kernel memory: 200K (c0843000 - c0875000)
  864. mount: mounting tmpfs on /dev/shm failed: No such file or directory
  865. Starting logging: OK
  866. Initializing random number generator... done.
  867. Starting network...
  868. ip: RTNETLINK answers: File exists
  869. / # [ 7.411932@0] cpu freq limited to 1200000000
  870. [ 7.511914@0] cpu freq limited to 1200000000
  871.  
  872. / # cat /proc/cpuinfo
  873. Processor: ARMv7 Processor rev 0 (v7l)
  874. processor: 0
  875. BogoMIPS: 238.71
  876.  
  877. processor: 1
  878. BogoMIPS: 239.37
  879.  
  880. Features: swp half thumb fastmult vfp edsp neon vfpv3 tls
  881. CPU implementer: 0x41
  882. CPU architecture: 7
  883. CPU variant: 0x3
  884. CPU part: 0xc09
  885. CPU revision: 0
  886.  
  887. Hardware: Amlogic Meson6 platform
  888. Revision: 0000
  889. Serial: 0000000000000000
  890. / #
RAW Paste Data