log

GXL:BL1:9ac50e:a1974b;FEAT:ADFC31AC;POC:3;RCY:0;EMMC:800;NAND:81;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 114367

BL2 Built : 15:21:58, Mar 26 2020. gxl g486bc38 - gongwei.chen@droid11-sz

set vcck to 1120 mv
set vddee to 1000 mv
Board ID = 2
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz - FAIL
DDR3 chl: Rank0 16bit @ 792MHz
bist_test rank: 0 1c 00 38 39 1a 59 1f 00 3f 35 15 55 2d 2d 2d 2d 2d 2d 2d 2d 2d 2d 2d 2d 678   - PASS

Rank0: 2048MB-2T-11
AddrBus test pass!
Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000, part: 0
New fip structure!
Load bl30 from SD, src: 0x00010200, des: 0x013c0000, size: 0x0000d600, part: 0
Load bl31 from SD, src: 0x00020200, des: 0x05100000, size: 0x0002c400, part: 0
0002c400Load bl33 from SD, src: 0x00050200, des: 0x01000000, size: 0x00081e00, part: 0
NOTICE:  BL3-1: v1.0(release):f5121da90
NOTICE:  BL3-1: Built : 20:18:22, Nov 22 2019
[BL31]: GXL CPU setup!
NOTICE:  BL3-1: GXL normal boot!
NOTICE:  BL3-1: BL33 decompress pass
mpu_config_enable:system pre init ok
dmc sec lock
[Image: gxl_v1.1.3394-7d43064d5 2020-05-07 15:37:15 gongwei.chen@droid11-sz]
OPS=0xa2
21 0b a2 00 d2 6d b5 f1 2d 00 27 d9 41 3d 87 cd
[0.772157 Inits done]
secure task start!
high task start!
low task start!
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01 (Aug 12 2023 - 13:05:34)

DRAM:  2 GiB
Relocation Offset is: 76e79000
mmu cfg end: 0x80000000
mmu cfg end: 0x80000000
register usb cfg[0][1] = 0000000077f4df30
[CANVAS]canvas init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC:   aml_priv->desc_buf = 0x0000000073e796b0
aml_priv->desc_buf = 0x0000000073e7b9f0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
emmc/sd response timeout, cmd1, cmd->cmdarg=0x40000000, status=0x1ff2800
MMC init failed
Using default environment

In:    serial
Out:   serial
Err:   serial
aml log : internal sys error!
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
emmc/sd response timeout, cmd1, cmd->cmdarg=0x40000000, status=0x1ff2800
_dtb_init()-3516: mmc init failed
      Amlogic multi-dtb tool
      Cannot find legal dtb!
[store]Err:do_store_dtb_ops,L425:Fail in fdt check header
board_late_init(): [store dtb read $dtb_mem_addr] fail
load dtb to 1000000
[store]To run cmd[emmc dtb_read 1000000 0x40000]
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
emmc/sd response timeout, cmd1, cmd->cmdarg=0x40000000, status=0x1ff2800
_dtb_init()-3516: mmc init failed
      Amlogic multi-dtb tool
      Cannot find legal dtb!
[store]Err:do_store_dtb_ops,L425:Fail in fdt check header
board_late_init(): store dtb read 1000000 fail
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: driver version: v20190313
vpu: detect chip type: 2
vpu: clk_level default: 7(666667000Hz), max: 7(666667000Hz)
vpu: clk_level = 7
vpu: vpu_power_on
vpu: set_vpu_clk
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x300)
vpu: set_vpu_clk finish
vpu: vpu_module_init_config
vpp: vpp_init
cvbs: cpuid:0x21
hpd_state=0
do_hpd_detect: hdmimode=1080p60hz
do_hpd_detect: colorattribute=444,8bit
Saving Environment to aml-storage...
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
emmc/sd response timeout, cmd1, cmd->cmdarg=0x40000000, status=0x1ff2800
MMC init failed
vpp: vpp_matrix_update: 2
cvbs performance type = 6, table = 0
cvbs_config_hdmipll_gxl
cvbs_set_vid2_clk
card in
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 40000000
init_part() 282: PART_TYPE_DOS
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 11
OEM: 455a
Name: EZSD1
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: (0xe8f600000 Bytes) 58.2 GiB
mmc clock: 40000000
Bus Width: 4-bit
Net:   dwmac.c9410000[KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
MACADDR:02:2d:f1:b5:6d:d2(from chipid)

Warning: dwmac.c9410000 MAC addresses don't match:
Address in SROM is         3a:37:25:c7:19:c3
Address in environment is  02:2d:f1:b5:6d:d2

ramdump_init, add:0, size:0
CONFIG_AVB2: null
Start read misc partition datas!
Cannot find dev.
amlmmc cmd <NULL> failed

store - STORE sub-system

Usage:
store init flag
store read name addr off|partition size
    read 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
    write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
        write uboot to the boot device
store erase boot/data:
        erase the area which is uboot or data
store erase partition <partition_name>:
        erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
        scrub the area from offset and size
store dtb iread/read/write addr <size>
        read/write dtb, size is optional
store key read/write addr <size>
        read/write key, size is optional
store ddr_parameter read/write addr <size>
        read/write ddr parameter, size is optional
store mbr addr
   update mbr/partition table by dtb
store bootlog
   show boot logs

[burnup]Err:store_read_ops,L101:cmd failed, ret=1, [store  read misc 0x73e68090  0x0  0x820]
failed to store read misc.
Magic  is incorrect.
boot-info is invalid. Resetting.
save boot-info
Cannot find dev.
amlmmc cmd <NULL> failed

store - STORE sub-system

Usage:
store init flag
store read name addr off|partition size
    read 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
    write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
        write uboot to the boot device
store erase boot/data:
        erase the area which is uboot or data
store erase partition <partition_name>:
        erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
        scrub the area from offset and size
store dtb iread/read/write addr <size>
        read/write dtb, size is optional
store key read/write addr <size>
        read/write key, size is optional
store ddr_parameter read/write addr <size>
        read/write ddr parameter, size is optional
store mbr addr
   update mbr/partition table by dtb
store bootlog
   show boot logs

[burnup]Err:store_write_ops,L165:cmd [store  write misc 0x73e68090  0x0  0x820] failed active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=0
aml log : internal sys error!
reboot_mode:::: cold_boot
s_version: 01.01.230812.130534
[KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
[OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[OSD]VPP_OFIFO_SIZE:0xfff00fff
[CANVAS]addr=0x3d800000 width=3840, height=2160
Cannot find dev.
amlmmc cmd <NULL> failed

store - STORE sub-system

Usage:
store init flag
store read name addr off|partition size
    read 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
    write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
        write uboot to the boot device
store erase boot/data:
        erase the area which is uboot or data
store erase partition <partition_name>:
        erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
        scrub the area from offset and size
store dtb iread/read/write addr <size>
        read/write dtb, size is optional
store key read/write addr <size>
        read/write key, size is optional
store ddr_parameter read/write addr <size>
        read/write ddr parameter, size is optional
store mbr addr
   update mbr/partition table by dtb
store bootlog
   show boot logs

[burnup]Err:store_read_ops,L101:cmd failed, ret=1, [store  read logo 0x1080000  0x0  0x2000]
Err imgread(L563):Fail to read 0x2000B from part[logo] at offset 0
There is no valid bmp file at the given address
[OSD]osd_hw.free_dst_data: 0,719,0,575
s_version: 01.01.230812.130534
[KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
gpio: pin GPIOAO_2 (gpio 102) value is 1
Command: bcb uboot-command
Start read misc partition datas!
Cannot find dev.
amlmmc cmd <NULL> failed

store - STORE sub-system

Usage:
store init flag
store read name addr off|partition size
    read 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
    write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
        write uboot to the boot device
store erase boot/data:
        erase the area which is uboot or data
store erase partition <partition_name>:
        erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
        scrub the area from offset and size
store dtb iread/read/write addr <size>
        read/write dtb, size is optional
store key read/write addr <size>
        read/write key, size is optional
store ddr_parameter read/write addr <size>
        read/write ddr parameter, size is optional
store mbr addr
   update mbr/partition table by dtb
store bootlog
   show boot logs

[burnup]Err:store_read_ops,L101:cmd failed, ret=1, [store  read misc 0x73e68080  0x0  0x440]
failed to store read misc.
bcb - bcb

Usage:
bcb
This command will run some commands which saved in misc
partition by mark to decide whether execute command!
Command format:
  bcb bcb_mark
Example:
  /dev/block/misc partiton is saved some contents:
  uboot-command
  N/A
  setenv aa 11;setenv bb 22;setenv cc 33;saveenv;
So you can execute command: bcb uboot-command
saradc - saradc sub-system

Usage:
saradc saradc open <channel>    - open a SARADC channel
saradc close    - close the SARADC
saradc getval   - get the value in current channel
saradc test     - test the SARADC by channel-7
saradc get_in_range <min> <max> - return 0 if current value in the range of current channel

s_version: 01.01.230812.130534
[KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
CONFIG_SYSTEM_AS_ROOT: systemroot
system_mode: 1
Start read misc partition datas!
Cannot find dev.
amlmmc cmd <NULL> failed

store - STORE sub-system

Usage:
store init flag
store read name addr off|partition size
    read 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
    write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
        write uboot to the boot device
store erase boot/data:
        erase the area which is uboot or data
store erase partition <partition_name>:
        erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
        scrub the area from offset and size
store dtb iread/read/write addr <size>
        read/write dtb, size is optional
store key read/write addr <size>
        read/write key, size is optional
store ddr_parameter read/write addr <size>
        read/write ddr parameter, size is optional
store mbr addr
   update mbr/partition table by dtb
store bootlog
   show boot logs

[burnup]Err:store_read_ops,L101:cmd failed, ret=1, [store  read misc 0x73e68090  0x0  0x820]
failed to store read misc.
Magic  is incorrect.
boot-info is invalid. Resetting.
save boot-info
Cannot find dev.
amlmmc cmd <NULL> failed

store - STORE sub-system

Usage:
store init flag
store read name addr off|partition size
    read 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
    write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
        write uboot to the boot device
store erase boot/data:
        erase the area which is uboot or data
store erase partition <partition_name>:
        erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
        scrub the area from offset and size
store dtb iread/read/write addr <size>
        read/write dtb, size is optional
store key read/write addr <size>
        read/write key, size is optional
store ddr_parameter read/write addr <size>
        read/write ddr parameter, size is optional
store mbr addr
   update mbr/partition table by dtb
store bootlog
   show boot logs

[burnup]Err:store_write_ops,L165:cmd [store  write misc 0x73e68090  0x0  0x820] failed active slot = 0
CONFIG_AVB2: null
active_slot: normal avb2: 0
Cannot find dev.
amlmmc cmd <NULL> failed

store - STORE sub-system

Usage:
store init flag
store read name addr off|partition size
    read 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
    write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
        write uboot to the boot device
store erase boot/data:
        erase the area which is uboot or data
store erase partition <partition_name>:
        erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
        scrub the area from offset and size
store dtb iread/read/write addr <size>
        read/write dtb, size is optional
store key read/write addr <size>
        read/write key, size is optional
store ddr_parameter read/write addr <size>
        read/write ddr parameter, size is optional
store mbr addr
   update mbr/partition table by dtb
store bootlog
   show boot logs

[burnup]Err:store_read_ops,L101:cmd failed, ret=1, [store  read boot 0x1080000  0x0  0x100000]
Err imgread(L338):Fail to read 0x100000B from part[boot] at offset 0
s_version: 01.01.230812.130534
[KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
InUsbBurn
noSof
Device: SDIO Port B
Manufacturer ID: 11
OEM: 455a
Name: EZSD1
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: (0xe8f600000 Bytes) 58.2 GiB
mmc clock: 40000000
Bus Width: 4-bit
Device: SDIO Port B
Manufacturer ID: 11
OEM: 455a
Name: EZSD1
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: (0xe8f600000 Bytes) 58.2 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading aml_autoscript
628 bytes read in 3 ms (204.1 KiB/s)
## Executing script at 01080000
## defenv_reserve
Saving Environment to aml-storage...
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
emmc/sd response timeout, cmd1, cmd->cmdarg=0x40000000, status=0x1ff2800
MMC init failed
reboot use default mode: normal
boot_dev: 0x4
warning you may need update your uboot!
check_dev return 0

bl31 reboot reason: 0xd
bl31 reboot reason: 0x1
system cmd  1.