Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- # Rcv Wcid(1) AddBAReq
- Start Seq = 00000002
- MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!
- RMAC_RXD Header Format :RxNormal
- RMAC_RXD Header Format :RxNormal
- [04040C0C][04040C0D]
- DDR Calibration DQS reg = 00008888
- U-Boot 1.1.3 (Oct 16 2016 - 19:48:39)
- Board: Ralink APSoC DRAM: 64 MB
- relocate_code Pointer at: 83fb4000
- flash manufacture id: c8, device id 40 16
- find flash: GD25Q32B
- *** Warning - bad CRC, using default environment
- ============================================
- Ralink UBoot Version: 5.0.0.0
- --------------------------------------------
- ASIC 7628_MP (Port5<->None)
- DRAM component: 512 Mbits DDR, width 16
- DRAM bus: 16 bit
- Total memory: 64 MBytes
- Flash component: SPI Flash
- Date:Oct 16 2016 Time:19:48:39
- ============================================
- icache: sets:512, ways:4, linesz:32 ,total:65536
- dcache: sets:256, ways:4, linesz:32 ,total:32768
- ##### The CPU freq = 580 MHZ ####
- estimate memory size =64 Mbytes
- RESET MT7628 PHY!!!!!!
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 9: Load Boot Loader code then write to Flash via TFTP.
- default: 3 0
- 3: System Boot system code via Flash.
- ## Booting image at bc050000 ...
- Image Name: Linux Kernel Image
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 3258253 Bytes = 3.1 MB
- Load Address: 80000000
- Entry Point: 8000c150
- Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 8000c150) ...
- ## Giving linux memsize in MB, 64
- Starting kernel ...
- LINUX started...
- THIS IS ASIC
- Linux version 2.6.36 (root@ubuntu) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #173 Wed Jun 21 19:46:41 CST 2017
- The CPU feqenuce set to 575 MHz
- MIPS CPU sleep mode enabled.
- CPU revision is: 00019655 (MIPS 24Kc)
- Software DMA cache coherency
- Determined physical RAM map:
- memory: 04000000 @ 00000000 (usable)
- Initrd not found or empty - disabling initrd
- Zone PFN ranges:
- Normal 0x00000000 -> 0x00004000
- Movable zone start PFN for each node
- early_node_map[1] active PFN ranges
- 0: 0x00000000 -> 0x00004000
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=
- PID hash table entries: 256 (order: -2, 1024 bytes)
- Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
- Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- Writing ErrCtl register=00027d48
- Readback ErrCtl register=00027d48
- Memory: 58740k/65536k available (3182k kernel code, 6748k reserved, 766k data, 1996k init, 0k highmem)
- NR_IRQS:128
- console [ttyS1] enabled
- Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 512
- NET: Registered protocol family 16
- RALINK_GPIOMODE = 54050404
- RALINK_GPIOMODE = 54040404
- ***** Xtal 40MHz *****
- start PCIe register access
- RALINK_RSTCTRL = 2400000
- RALINK_CLKCFG1 = fdbfffc0
- *************** MT7628 PCIe RC mode *************
- PCIE0 enabled
- Port 0 N_FTS = 1b105000
- init_rt2880pci done
- bio: create slab <bio-0> at 0
- vgaarb: loaded
- pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
- pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
- pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
- pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
- pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff]
- pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
- pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff 64bit] (PCI address [0x20000000-0x200fffff]
- pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
- pci 0000:00:00.0: PCI bridge to [bus 01-01]
- pci 0000:00:00.0: bridge window [io disabled]
- pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
- pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
- BAR0 at slot 0 = 0
- bus=0x0, slot = 0x0
- res[0]->start = 0
- res[0]->end = 0
- res[1]->start = 20200000
- res[1]->end = 2020ffff
- res[2]->start = 0
- res[2]->end = 0
- res[3]->start = 0
- res[3]->end = 0
- res[4]->start = 0
- res[4]->end = 0
- res[5]->start = 0
- res[5]->end = 0
- bus=0x1, slot = 0x0
- res[0]->start = 20000000
- res[0]->end = 200fffff
- res[1]->start = 0
- res[1]->end = 0
- res[2]->start = 0
- res[2]->end = 0
- res[3]->start = 0
- res[3]->end = 0
- res[4]->start = 0
- res[4]->end = 0
- res[5]->start = 0
- res[5]->end = 0
- Switching to clocksource Ralink Systick timer
- NET: Registered protocol family 2
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 2048 (order: 2, 16384 bytes)
- TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
- TCP: Hash tables configured (established 2048 bind 2048)
- TCP reno registered
- UDP hash table entries: 256 (order: 0, 4096 bytes)
- UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- NET: Registered protocol family 1
- msgmni has been set to 114
- Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
- io scheduler noop registered (default)
- Ralink gpio driver initialized
- i2cdrv_major = 218
- Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
- serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
- serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
- brd: module loaded
- Read GD Flash ID!
- flash manufacture id: c8, device id 40 16
- GD25Q32B(c8 40160000) (4096 Kbytes)
- mtd .name = raspi, .size = 0x00400000 (4M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
- Creating 5 MTD partitions on "raspi":
- 0x000000000000-0x000000400000 : "ALL"
- 0x000000000000-0x000000030000 : "Bootloader"
- 0x000000030000-0x000000040000 : "Config"
- 0x000000040000-0x000000050000 : "Factory"
- 0x000000050000-0x000001000000 : "Kernel"
- mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x3b0000
- rdm_major = 253
- GMAC1_MAC_ADRH -- : 0x000000e0
- GMAC1_MAC_ADRL -- : 0x2087a3df
- Ralink APSoC Ethernet Driver Initilization. v3.1 256 rx/tx descriptors allocated, mtu = 1500!
- GMAC1_MAC_ADRH -- : 0x000000e0
- GMAC1_MAC_ADRL -- : 0x2087a3df
- PROC INIT OK!
- PPP generic driver version 2.4.2
- PPP MPPE Compression module registered
- NET: Registered protocol family 24
- PPTP driver version 0.8.5
- === pAd = c014d000, size = 1395872 ===
- <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
- <-- RTMPAllocAdapterBlock, Status=0
- RtmpChipOpsHook(492): Not support for HIF_MT yet!
- mt7628_init()-->
- mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
- e2.bin mt7628_init(1135)::(2), pChipCap->fw_len(63888)
- mt_bcn_buf_init(218): Not support for HIF_MT yet!
- <--mt7628_init()
- nf_conntrack version 0.5.0 (917 buckets, 3668 max)
- IPVS: Registered protocols ()
- IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
- IPVS: ipvs loaded.
- GRE over IPv4 demultiplexor driver
- gre: can't add protocol
- ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
- TCP cubic registered
- NET: Registered protocol family 10
- NET: Registered protocol family 17
- L2TP core driver, V2.0
- PPPoL2TP kernel driver, V2.0
- 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
- All bugs added by David S. Miller <davem@redhat.com>
- Warning: unable to open an initial console.
- Freeing unused kernel memory: 1996k freed
- Algorithmics/MIPS FPU Emulator v1.5
- ,--. <__)
- `- |________7
- |`. |\
- .--|. \ |.\--.
- / j \ `.7__j__\ \
- | o | (o)____O) |
- \ / J \ /
- `---' `---'
- init: can't log to /dev/tty5
- starting pid 116, tty '/dev/ttyS1': '/bin/sh'
- BusyBox v1.12.1 (2016-09-07 20:09:12 CST) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- # Raeth v3.1 (Tasklet,SkbRecycle)
- phy_tx_ring = 0x03352000, tx_ring = 0xa3352000
- phy_rx_ring0 = 0x03353000, rx_ring0 = 0xa3353000
- GMAC1_MAC_ADRH -- : 0x000000e0
- GMAC1_MAC_ADRL -- : 0x2087a3df
- RT305x_ESW: Link Status Changed
- device eth2 entered promiscuous mode
- device eth2.1 entered promiscuous mode
- device eth2.2 entered promiscuous mode
- device eth2.3 entered promiscuous mode
- device eth2.4 entered promiscuous mode
- device eth2.5 entered promiscuous mode
- DHCP DNS Enable:0
- DHCP DNS IP:0.0.0.0 DNS IP:00.00.00.00
- TX_BCN DESC a31cf000 size = 320
- RX[0] DESC a31d2000 size = 1024
- RX[1] DESC a31d3000 size = 1024
- E2pAccessMode=2
- cfg_mode=9
- cfg_mode=9
- wmode_band_equal(): Band Equal!
- AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
- APSDCapable[0]=0
- APSDCapable[1]=0
- APSDCapable[2]=0
- APSDCapable[3]=0
- APSDCapable[4]=0
- APSDCapable[5]=0
- APSDCapable[6]=0
- APSDCapable[7]=0
- APSDCapable[8]=0
- APSDCapable[9]=0
- APSDCapable[10]=0
- APSDCapable[11]=0
- APSDCapable[12]=0
- APSDCapable[13]=0
- APSDCapable[14]=0
- APSDCapable[15]=0
- default ApCliAPSDCapable[0]=0
- Key1Str is Invalid key length(0) or Type(0)
- Key2Str is Invalid key length(0) or Type(0)
- Key3Str is Invalid key length(0) or Type(0)
- Key4Str is Invalid key length(0) or Type(0)
- 8d:72:10:75:43:2e:6a:9f:9c:c1:62:7f:d3:56:4d:9d:
- 54:6d:26:31:db:94:5a:46:48:5e:93:bc:38:51:94:9d:
- RTMPSetDefaultChannel() : default channel to 1
- load fw image from fw_header_image
- AndesMTLoadFwMethod1(2182)::pChipCap->fw_len(63888)
- FW Version:20151201
- FW Build Date:20151201183641
- CmdAddressLenReq:(ret = 0)
- CmdFwStartReq: override = 1, address = 1048576
- CmdStartDLRsp: WiFI FW Download Success
- MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
- efuse_probe: efuse = 10000002
- RtmpChipOpsEepromHook::e2p_type=2, inf_Type=4
- RtmpEepromGetDefault::e2p_dafault=2
- RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2
- NVM is FLASH mode
- 1. Phy Mode = 14
- Country Region from e2p = ffff
- tssi_1_target_pwr_g_band = 30
- 2. Phy Mode = 14
- 3. Phy Mode = 14
- NICInitPwrPinCfg(11): Not support for HIF_MT yet!
- NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet!
- mt_mac_init()-->
- MtAsicInitMac()-->
- mt7628_init_mac_cr()-->
- MtAsicSetMacMaxLen(1276): Set the Max RxPktLen=1024!
- <--mt_mac_init()
- WTBL Segment 1 info:
- MemBaseAddr/FID:0x28000/0
- EntrySize/Cnt:32/128
- WTBL Segment 2 info:
- MemBaseAddr/FID:0x40000/0
- EntrySize/Cnt:64/128
- WTBL Segment 3 info:
- MemBaseAddr/FID:0x42000/64
- EntrySize/Cnt:64/128
- WTBL Segment 4 info:
- MemBaseAddr/FID:0x44000/128
- EntrySize/Cnt:32/128
- AntCfgInit(2946): Not support for HIF_MT yet!
- MCS Set = ff ff 00 00 01
- MtAsicSetChBusyStat(861): Not support for HIF_MT yet!
- SYNC - BBP R4 to 20MHz.l
- CmdSlotTimeSet:(ret = 0)
- SYNC - BBP R4 to 20MHz.l
- SYNC - BBP R4 to 20MHz.l
- SYNC - BBP R4 to 20MHz.l
- SYNC - BBP R4 to 20MHz.l
- SYNC - BBP R4 to 20MHz.l
- SYNC - BBP R4 to 20MHz.l
- SYNC - BBP R4 to 20MHz.l
- MtAsicSetRalinkBurstMode(3051): Not support for HIF_MT yet!
- MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
- MtAsicSetTxPreamble(3030): Not support for HIF_MT yet!
- MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!
- The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
- MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
- Main bssid = 00:e0:20:87:a3:e1
- <==== rt28xx_init, Status=0
- @@@ ed_monitor_exit : ===>
- @@@ ed_monitor_exit : <===
- mt7628_set_ed_cca: TURN OFF EDCCA mac 0x10618 = 0xd7083f0f, EDCCA_Status=0
- WiFi Startup Cost (ra0): 3.568s
- device ra0 entered promiscuous mode
- register rt2860
- === pAd = c0782000, size = 2162072 ===
- <-- RTMPAllocTxRxRingMemory, Status=0
- <-- RTMPAllocAdapterBlock, Status=0
- pAd->CSRBaseAddress =0xc0680000, csr_addr=0xc0680000!
- device_id =0x7662
- ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
- ====> mt76x2_ePA_per_rate_compensate_init: 5868 is_ePA: 1
- E2pAccessMode=2
- cfg_mode=14
- cfg_mode=14
- wmode_band_equal(): Band Not Equal!
- APSDCapable[0]=0
- APSDCapable[1]=0
- APSDCapable[2]=0
- APSDCapable[3]=0
- APSDCapable[4]=0
- APSDCapable[5]=0
- APSDCapable[6]=0
- APSDCapable[7]=0
- APSDCapable[8]=0
- APSDCapable[9]=0
- APSDCapable[10]=0
- APSDCapable[11]=0
- APSDCapable[12]=0
- APSDCapable[13]=0
- APSDCapable[14]=0
- APSDCapable[15]=0
- default ApCliAPSDCapable[0]=0
- Key1Str is Invalid key length(0) or Type(0)
- Key2Str is Invalid key length(0) or Type(0)
- Key3Str is Invalid key length(0) or Type(0)
- Key4Str is Invalid key length(0) or Type(0)
- d9:0f:b1:03:26:34:13:9b:08:78:8d:a8:0a:1b:e0:08:
- 4c:08:f1:aa:71:1b:33:88:44:b0:30:7b:0a:93:3c:cb:
- WiFi Mcast disabled=0
- RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
- NVM is FLASH mode (pAd->flash_offset = 0x48000)
- get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
- build time =
- 20141115060606a
- rom patch for E3 IC
- platform =
- ALPS
- hw/sw version =
- patch version =
- FW Version:0.0.00 Build:1
- Build Time:201507311614____
- fw for E3 IC
- RX[0] DESC a2dc6000 size = 4096
- RX[1] DESC a2dc7000 size = 4096
- E2pAccessMode=2
- cfg_mode=14
- cfg_mode=14
- wmode_band_equal(): Band Not Equal!
- APSDCapable[0]=0
- APSDCapable[1]=0
- APSDCapable[2]=0
- APSDCapable[3]=0
- APSDCapable[4]=0
- APSDCapable[5]=0
- APSDCapable[6]=0
- APSDCapable[7]=0
- APSDCapable[8]=0
- APSDCapable[9]=0
- APSDCapable[10]=0
- APSDCapable[11]=0
- APSDCapable[12]=0
- APSDCapable[13]=0
- APSDCapable[14]=0
- APSDCapable[15]=0
- default ApCliAPSDCapable[0]=0
- Key1Str is Invalid key length(0) or Type(0)
- Key2Str is Invalid key length(0) or Type(0)
- Key3Str is Invalid key length(0) or Type(0)
- Key4Str is Invalid key length(0) or Type(0)
- d9:0f:b1:03:26:34:13:9b:08:78:8d:a8:0a:1b:e0:08:
- 4c:08:f1:aa:71:1b:33:88:44:b0:30:7b:0a:93:3c:cb:
- WiFi Mcast disabled=0
- 1. Phy Mode = 49
- get_chl_grp:illegal channel (167)
- get_chl_grp:illegal channel (167)
- get_chl_grp:illegal channel (169)
- get_chl_grp:illegal channel (169)
- get_chl_grp:illegal channel (171)
- get_chl_grp:illegal channel (171)
- drivers/net/wireless/rlt_wifi_ap/../rlt_wifi/chips/mt76x2.c:3028 assert (ad->TxPower[choffset].Channel == 42)failed
- Country Region from e2p = ffff
- mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0
- mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=1
- mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=15, low_temp_slope=9
- mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0
- mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4
- mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0
- mt76x2_get_external_lna_gain::LNA type=0x1, BLNAGain=0xffffff8c, ALNAGain0=0xffffff8c, ALNAGain1=0xffffff8c, ALNAGain2=0xffffff8c
- 2. Phy Mode = 49
- 3. Phy Mode = 49
- andes_pci_fw_init
- 0x1300 = 00073200
- AntCfgInit: primary/secondary ant 0/1
- andes_load_cr:cr_type(2)
- ChipStructAssign(): MT76x2 hook !
- RTMPSetPhyMode: channel is out of range, use first channel=0
- MCS Set = ff ff 00 00 01
- mt76x2_bbp_adjust():rf_bw=2, ext_ch=3, PrimCh=153, HT-CentCh=151, VHT-CentCh=155
- APStartUp(): AP Set CentralFreq at 155(Prim=153, HT-CentCh=151, VHT-CentCh=155, BBP_BW=2)
- mt76x2_calibration(channel = 155)
- Main bssid = 00:e0:20:87:a3:e2
- mt76x2_reinit_agc_gain:original agc_vga0 = 0x48, agc_vga1 = 0x48
- mt76x2_reinit_agc_gain:updated agc_vga0 = 0x48, agc_vga1 = 0x48
- mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x33, hi_lna1 = 0x33
- mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x33, hi_lna1 = 0x33
- original vga value(chain0) = 48
- original vga value(chain1) = 48
- <==== rt28xx_init, Status=0
- get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=apclii
- RTMPDrvOpen(1):Check if PDMA is idle!
- RTMPDrvOpen(2):Check if PDMA is idle!
- device rai0 entered promiscuous mode
- AddTxSType: already registered TxSType (PID = 32, Format = 0
- The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
- device apcli0 entered promiscuous mode
- br0: port 8(apcli0) entering learning state
- br0: port 8(apcli0) entering learning state
- br0: port 7(rai0) entering learning state
- br0: port 7(rai0) entering learning state
- br0: port 6(ra0) entering learning state
- br0: port 6(ra0) entering learning state
- br0: port 5(eth2.5) entering learning state
- br0: port 5(eth2.5) entering learning state
- br0: port 4(eth2.4) entering learning state
- br0: port 4(eth2.4) entering learning state
- br0: port 3(eth2.3) entering learning state
- br0: port 3(eth2.3) entering learning state
- br0: port 2(eth2.2) entering learning state
- br0: port 2(eth2.2) entering learning state
- br0: port 1(eth2.1) entering learning state
- br0: port 1(eth2.1) entering learning state
- br0: port 8(apcli0) entering learning state
- br0: port 7(rai0) entering learning state
- br0: port 6(ra0) entering learning state
- br0: port 5(eth2.5) entering learning state
- br0: port 4(eth2.4) entering learning state
- br0: port 3(eth2.3) entering learning state
- br0: port 2(eth2.2) entering learning state
- br0: port 1(eth2.1) entering learning state
- br0: port 8(apcli0) entering learning state
- br0: port 8(apcli0) entering learning state
- br0: port 7(rai0) entering learning state
- br0: port 7(rai0) entering learning state
- br0: port 6(ra0) entering learning state
- br0: port 6(ra0) entering learning state
- br0: port 5(eth2.5) entering learning state
- br0: port 5(eth2.5) entering learning state
- br0: port 4(eth2.4) entering learning state
- br0: port 4(eth2.4) entering learning state
- br0: port 3(eth2.3) entering learning state
- br0: port 3(eth2.3) entering learning state
- br0: port 2(eth2.2) entering learning state
- br0: port 2(eth2.2) entering learning state
- br0: port 1(eth2.1) entering learning state
- br0: port 1(eth2.1) entering learning state
- led=13, on=4000, off=1, blinks,=1, reset=1, time=4000
- br0: port 8(apcli0) entering forwarding state
- br0: port 7(rai0) entering forwarding state
- br0: port 6(ra0) entering forwarding state
- br0: port 5(eth2.5) entering forwarding state
- br0: port 4(eth2.4) entering forwarding state
- br0: port 3(eth2.3) entering forwarding state
- br0: port 2(eth2.2) entering forwarding state
- br0: port 1(eth2.1) entering forwarding state
- ScanNextChannel:: specific the NSA-3 scanning
- ScanNextChannel:: specific the NSA-3 scanning
- ScanNextChannel:: specific the NSA-3 scanning
- ScanNextChannel:: specific the NSA-3 scanning
- ScanNextChannel:: specific the NSA-3 scanning
- ScanNextChannel:: specific the NSA-3 scanning
- ScanNextChannel:: specific the NSA-3 scanning
- ScanNextChannel:: specific the NSA-3 scanning
- ScanNextChannel:: specific the NSA-3 scanning
- ScanNextChannel:: specific the NSA-3 scanning
- ScanNextChannel:: specific the NSA-3 scanning
- ScanNextChannel:: specific the NSA-3 scanning
- ScanNextChannel:: specific the NSA-3 scanning
- ScanNextChannel:: specific the NSA-3 scanning
- MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0
- MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
- MtAsicSetRalinkBurstMode(3051): Not support for HIF_MT yet!
- MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
- MtAsicSetTxPreamble(3030): Not support for HIF_MT yet!
- MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!
- AddTxSType: already registered TxSType (PID = 32, Format = 0
- The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
- AddTxSType: already registered TxSType (PID = 6, Format = 0
- AddTxSType: already registered TxSType (PID = 8, Format = 0
- MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
- Main bssid = 00:e0:20:87:a3:e1
- ApCliValidateRSNIE - Unknown pEid->Eid(11)
- MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement