Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 1.1.1 (Development build, svnversion: exported) (Build time: Mar 22 2010 - 12:14:14)
- Warning: Board descriptor tuple not found in eeprom, using defaults
- CUST_DSR1000 board revision major:2, minor:0, serial #: unknown
- OCTEON CN5010-SCP pass 1.1, Core clock: 500 MHz, DDR clock: 200 MHz (400 Mhz data rate)
- DRAM: 256 MB
- Flash: 32 MB
- Clearing DRAM...... done
- BIST check passed.
- Starting PCI
- PCI Status: PCI 32-bit
- PCI BAR 0: 0x00000000, PCI BAR 1: Memory 0x00000000 PCI 0xf8000000
- Net: octeth0, octeth1, octeth2
- Hit any key to stop autoboot: 0
- D-Link DSR-1000N bootloader#
- D-Link DSR-1000N bootloader#
- D-Link DSR-1000N bootloader#
- D-Link DSR-1000N bootloader#
- Unknown command '' - try 'help'
- D-Link DSR-1000N bootloader#
- D-Link DSR-1000N bootloader# run bsd
- Interface 0 has 3 ports (RGMII)
- Using octeth0 device
- TFTP from server 192.168.0.90; our IP address is 192.168.0.10
- Filename 'DSR-1000N/boot/kernel/kernel'.
- Load address: 0xaa00000
- Loading: octeth0: Up 1000 Mbps Full duplex (port 0)
- #################################################################
- ###########
- done
- Bytes transferred = 10838150 (a56086 hex), 5183 Kbytes/sec
- argv[2]: numcores=1
- ELF file is 64 bit
- Attempting to allocate memory for ELF segment: addr: 0xffffffff80100080 (adjusted to: 0x0000000000100080), size 0xaef7e0
- Allocated memory for ELF segment: addr: 0xffffffff80100080, size 0xaef7e0
- Loading .text @ 0xffffffff80100080 (0x6a7f80 bytes)
- Loading .MIPS.stubs @ 0xffffffff807a8000 (0x10 bytes)
- Loading .rodata @ 0xffffffff807aa000 (0x45de0 bytes)
- Loading .MIPS.options @ 0xffffffff807efde0 (0x8ea8 bytes)
- Loading .rodata.str1.8 @ 0xffffffff807f8c88 (0x8e7a8 bytes)
- Loading set_sysctl_set @ 0xffffffff80887430 (0x2d78 bytes)
- Loading .interp @ 0xffffffff8088a1a8 (0xd bytes)
- Loading .dynsym @ 0xffffffff8088a1b8 (0x35cd0 bytes)
- Loading .dynstr @ 0xffffffff808bfe88 (0x25b32 bytes)
- Loading .hash @ 0xffffffff808e59c0 (0x10fc4 bytes)
- Loading set_sysinit_set @ 0xffffffff808f6988 (0x1a30 bytes)
- Loading set_sysuninit_set @ 0xffffffff808f83b8 (0xc98 bytes)
- Loading set_modmetadata_set @ 0xffffffff808f9050 (0xf38 bytes)
- Loading set_kdb_dbbe_set @ 0xffffffff808f9f88 (0x10 bytes)
- Loading set_ah_chips @ 0xffffffff808f9f98 (0x48 bytes)
- Loading set_ah_rfs @ 0xffffffff808f9fe0 (0x28 bytes)
- Loading set_cons_set @ 0xffffffff808fa008 (0x18 bytes)
- Loading usb_host_id @ 0xffffffff808fa020 (0x9ca0 bytes)
- Loading usb_dual_id @ 0xffffffff80903cc0 (0x60 bytes)
- Loading set_ratectl_set @ 0xffffffff80903d20 (0x10 bytes)
- Loading set_crypto_set @ 0xffffffff80903d30 (0x18 bytes)
- Loading set_ieee80211_ioctl_setset @ 0xffffffff80903d48 (0x18 bytes)
- Loading set_ieee80211_ioctl_getset @ 0xffffffff80903d60 (0x18 bytes)
- Loading set_scanner_set @ 0xffffffff80903d78 (0x28 bytes)
- Loading kern_conf @ 0xffffffff80903da0 (0x8c8 bytes)
- Loading .data @ 0xffffffff80906000 (0xa5a00 bytes)
- Loading .got @ 0xffffffff809aba00 (0x4a08 bytes)
- Loading .rld_map @ 0xffffffff809b0408 (0x4 bytes)
- Loading set_pcpu @ 0xffffffff809b0440 (0xda4 bytes)
- Loading .sdata @ 0xffffffff809b11e4 (0x1c bytes)
- Clearing .bss @ 0xffffffff809b1200 (0x23e660 bytes)
- ## Loading Linux kernel with entry point: 0xffffffff80100080 ...
- Bootloader: Done loading app on coremask: 0x1
- Boot Descriptor Ver: 6 -> 1/2 CPU clock: 500MHz Core Mask: 0
- Board Type: 20006 Revision: 2/0
- Mac Address 00.DE.AD.20.75.00 (255)
- Board: CUST_DLINK_DSR1000N
- Model: CN5010p1.1-500-SCP
- Cache info:
- picache_stride = 4096
- picache_loopcount = 8
- pdcache_stride = 256
- pdcache_loopcount = 64
- cpu0: Cavium processor v1.6
- MMU: Standard TLB, 64 entries
- L1 i-cache: 4 ways of 64 sets, 128 bytes per line
- L1 d-cache: 64 ways of 2 sets, 128 bytes per line
- Config1=0xfe3303da<COP2,PerfCount,WatchRegs,EJTAG>
- Config3=0x1080
- Physical memory chunk(s):
- 0xbf0000 - 0xfeeffff, 254803968 bytes (62208 pages)
- Maxmem is 0xfef0000
- pcpu is available at virtual address 0xc000000000000000.
- KDB: debugger backends: ddb
- KDB: current backend: ddb
- Octeon SDK: Cavium Networks Octeon SDK version 2.0.0, build 366
- Available Octeon features: SAAD CRYPTO USB
- Copyright (c) 1992-2011 The FreeBSD Project.
- Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
- The Regents of the University of California. All rights reserved.
- FreeBSD is a registered trademark of The FreeBSD Foundation.
- FreeBSD 10.0-CURRENT #97 r0:226680M: Fri Oct 28 14:58:38 EEST 2011
- ray@terran.dlink.ua:/usr/obj/mips.mips64eb/usr/1/MIPS_FreeBSD/HEAD/head/sys/OCTEON1 mips
- WARNING: WITNESS option enabled, expect reduced performance.
- real memory = 254803968 (248832K bytes)
- Physical memory chunk(s):
- 0x00d0d000 - 0x0f796fff, 245932032 bytes (60042 pages)
- avail memory = 242606080 (231MB)
- ULE: setup cpu 0
- wlan: <802.11 Link Layer>
- mem: <memory>
- crypto: <crypto core>
- random: <entropy source, Software, Yarrow>
- nfslock: pseudo-device
- null: <null device, zero device>
- nexus0: <MIPS32 root nexus>
- clock0: <Generic MIPS32 ticker> on nexus0
- Timecounter "MIPS32" frequency 500000000 Hz quality 800
- Event timer "MIPS32" frequency 500000000 Hz quality 800
- rnd0: <Cavium Octeon Random Number Generator> on nexus0
- cryptocteon0: <Octeon Secure Coprocessor> on nexus0
- crypto: assign cryptocteon0 driver id 0, flags 83886080
- crypto: cryptocteon0 registers alg 6 flags 0 maxoplen 0
- crypto: cryptocteon0 registers alg 7 flags 0 maxoplen 0
- crypto: cryptocteon0 registers alg 1 flags 0 maxoplen 0
- crypto: cryptocteon0 registers alg 2 flags 0 maxoplen 0
- crypto: cryptocteon0 registers alg 11 flags 0 maxoplen 0
- ciu0: <Cavium Octeon Central Interrupt Unit> on nexus0
- obio0 on ciu0
- uart1: <Octeon-16550 channel 1> on obio0
- uart1: fast interrupt
- uart1: console (115200,n,8,1)
- uart0: <Octeon-16550 channel 0> on obio0
- uart0: fast interrupt
- uart0: console (115200,n,8,1)
- octebus0: <Cavium Octeon Ethernet pseudo-bus> on ciu0
- cavium-ethernet: Cavium Networks Octeon SDK version 2.0.0, build 366
- Interface 0 has 3 ports (RGMII)
- Warning: Enabling IPD when IPD already enabled.
- Warning: Enabling PKO when PKO already enabled.
- octe0: <Cavium Octeon RGMII Ethernet> on octebus0
- DUMP PHY0:
- 1140 796d 0143 bf88 0de1 41e1 0067 2001 0000 0f00 0000 0000 0000 0000 0000 3000
- 0000 0301 0000 0000 0000 0028 0000 0f75 0c00 f514 040e ffff 0000 0184 0000 0000
- DUMP PHY1:
- 1140 7949 0143 bf88 0de1 0000 0064 2001 0000 0f00 0000 0000 0000 0000 0000 3000
- 0000 2000 0000 0000 0000 0028 0000 0f75 0c00 1000 0000 ffff 0000 0000 0000 0000
- DUMP PHY2:
- 1140 7949 0143 bf88 0de1 0000 0064 2001 0000 0f00 0000 0000 0000 0000 0000 3000
- 0000 2000 0000 0000 0000 0028 0000 0f75 0c00 1000 0000 ffff 2c4e 0000 0000 0000
- DUMP PHY3:
- 1140 7949 0143 bf88 0de1 0000 0064 2001 0000 0f00 0000 0000 0000 0000 0000 3000
- 0000 2000 0000 0000 0000 0028 0000 0f75 0c00 1000 0000 ffff 2c60 0000 0000 0000
- DUMP PHY4:
- 1140 796d 0143 bf88 0de1 41e1 0067 2001 0000 0f00 0000 0000 0000 0000 0000 3000
- 0000 2301 0000 0000 0000 0028 0000 0f75 0c00 f514 040e ffff 0000 040d 0000 0000
- DUMP PHY5:
- 1140 0149 0143 bff0 01e0 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 c000
- 0190 0007 0042 0001 0011 0881 03c0 0000 0000 0000 0820 0000 0000 017c 0289 0000
- DUMP PHY8:
- 1140 7949 0143 bca2 01e1 0000 0064 2001 0000 0200 0000 0000 0000 0000 0000 3000
- 0000 2000 0000 0000 0000 0000 0000 0000 0400 1000 0000 ffff 3833 0000 0000 0000
- miibus0: <MII bus> on octe0
- ukphy0: <Generic IEEE 802.3u media interface> PHY 0 on miibus0
- ukphy0: OUI 0x000af7, model 0x0038, rev. 8
- ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
- ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
- ukphy1: OUI 0x000af7, model 0x0038, rev. 8
- ukphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
- ukphy2: <Generic IEEE 802.3u media interface> PHY 2 on miibus0
- ukphy2: OUI 0x000af7, model 0x0038, rev. 8
- ukphy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
- ukphy3: <Generic IEEE 802.3u media interface> PHY 3 on miibus0
- ukphy3: OUI 0x000af7, model 0x0038, rev. 8
- ukphy3: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
- ukphy4: <Generic IEEE 802.3u media interface> PHY 4 on miibus0
- ukphy4: OUI 0x000af7, model 0x0038, rev. 8
- ukphy4: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
- brgphy0: <BCM5709S 1000/2500baseSX PHY> PHY 5 on miibus0
- brgphy0: OUI 0x000af7, model 0x003f, rev. 0
- brgphy0: 1000baseSX-FDX, auto
- ukphy5: <Generic IEEE 802.3u media interface> PHY 8 on miibus0
- ukphy5: OUI 0x000af7, model 0x000a, rev. 2
- ukphy5: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
- MAC: 00:de:ad:20:75:00
- octe0: bpf attached
- octe0: Ethernet address: 00:de:ad:20:75:00
- octe1: <Cavium Octeon RGMII Ethernet> on octebus0
- DUMP PHY0:
- 1140 7949 0143 bf88 0de1 0000 0064 2001 0000 0f00 0000 0000 0000 0000 0000 3000
- 0000 0001 0000 0000 0000 0000 0000 0000 0400 0000 0000 ffff 0000 0000 0000 0000
- DUMP PHY1:
- 1540 7949 0143 bf88 0de1 0000 0064 2001 0000 0f00 0000 0000 0000 0000 0000 3000
- 0000 2000 0000 0000 0000 0000 0000 0000 0400 0000 0000 ffff 0000 0000 0000 0000
- DUMP PHY2:
- 1540 7949 0143 bf88 0de1 0000 0064 2001 0000 0f00 0000 0000 0000 0000 0000 3000
- 0000 2000 0000 0000 0000 0000 0000 0000 0400 0000 0000 ffff 0000 0000 0000 0000
- DUMP PHY3:
- 1540 7949 0143 bf88 0de1 0000 0064 2001 0000 0f00 0000 0000 0000 0000 0000 3000
- 0000 0000 0000 0000 0000 0000 0000 0000 0400 0000 0000 ffff 0000 0000 0000 0000
- DUMP PHY4:
- 1540 7949 0143 bf88 0de1 0000 0064 2001 0000 0f00 0000 0000 0000 0000 0000 3000
- 0000 2000 0000 0000 0000 0000 0000 0000 0400 0000 0000 ffff 0000 0000 0000 0000
- DUMP PHY5:
- 1140 0149 0143 bff0 01e0 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 c000
- 0190 0007 0042 0001 0011 0881 03c0 0000 0000 0000 0820 0000 0000 017c 0289 0000
- DUMP PHY8:
- 1540 7949 0143 bca2 01e1 0000 0064 2001 0000 0200 0000 0000 0000 0000 0000 3000
- 0000 0000 0000 0000 0000 0000 0000 0000 0400 0000 0000 ffff 0000 0000 0000 0000
- miibus1: <MII bus> on octe1
- ukphy6: <Generic IEEE 802.3u media interface> PHY 0 on miibus1
- ukphy6: OUI 0x000af7, model 0x0038, rev. 8
- ukphy6: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
- ukphy7: <Generic IEEE 802.3u media interface> PHY 1 on miibus1
- ukphy7: OUI 0x000af7, model 0x0038, rev. 8
- ukphy7: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
- ukphy8: <Generic IEEE 802.3u media interface> PHY 2 on miibus1
- ukphy8: OUI 0x000af7, model 0x0038, rev. 8
- ukphy8: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
- ukphy9: <Generic IEEE 802.3u media interface> PHY 3 on miibus1
- ukphy9: OUI 0x000af7, model 0x0038, rev. 8
- ukphy9: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
- ukphy10: <Generic IEEE 802.3u media interface> PHY 4 on miibus1
- ukphy10: OUI 0x000af7, model 0x0038, rev. 8
- ukphy10: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
- brgphy1: <BCM5709S 1000/2500baseSX PHY> PHY 5 on miibus1
- brgphy1: OUI 0x000af7, model 0x003f, rev. 0
- brgphy1: 1000baseSX-FDX, auto
- ukphy11: <Generic IEEE 802.3u media interface> PHY 8 on miibus1
- ukphy11: OUI 0x000af7, model 0x000a, rev. 2
- ukphy11: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
- MAC: 00:de:ad:20:75:00
- octe1: bpf attached
- octe1: Ethernet address: 00:de:ad:20:75:00
- octe2: <Cavium Octeon RGMII Ethernet> on octebus0
- DUMP PHY8:
- 1540 7949 0143 bca2 01e1 0000 0064 2001 0000 0200 0000 0000 0000 0000 0000 3000
- 0000 0000 0000 0000 0000 0000 0000 0000 0400 0000 0000 ffff 0000 0000 0000 0000
- miibus2: <MII bus> on octe2
- ukphy12: <Generic IEEE 802.3u media interface> PHY 8 on miibus2
- ukphy12: OUI 0x000af7, model 0x000a, rev. 2
- ukphy12: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
- MAC: 00:de:ad:20:75:00
- octe2: bpf attached
- octe2: Ethernet address: 00:de:ad:20:75:00
- pcib0: <Cavium Octeon PCI bridge> on ciu0
- pcib0: 32-bit PCI bus.
- pci0: <PCI bus> on pcib0
- pci0: domain=0, physical bus=0
- dotg0: <DWC like USB OTG controller> on ciu0
- dotg_init: READ4 from GSNPSID_REG 0x4f54265a
- dotg_init: READ4 from GSNPSID_REG+4 0x00000000
- usbus0 on dotg0
- usbus0: bpf attached
- dotg0: usbpf: Attached
- cfi_do_query: query at 0 with mask 0xff (w=1, s=2)
- cfi_do_query: cfi_read(sc, ofs, CFI_QRY_IDENT) return 0x51
- cfi0: detected with bus width = 1, address shift = 2
- cfi0: CFI Flash Manufacturer ID = 0x10, Device ID 0x01
- cfi0: Array mask = 0xff
- cfi0: <AMD/Fujitsu - 32MB> on ciu0
- cfi0:
- cfi0: [256x128KB]
- cfid0 on cfi0
- rtc0: <Cavium Octeon Realtime Clock> on nexus0
- rtc0: registered as a time-of-day clock (resolution 1000000us, adjustment 0.500000000s)
- cryptosoft0: <software crypto> on nexus0
- crypto: assign cryptosoft0 driver id 1, flags 100663296
- crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
- crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
- Device configuration finished.
- procfs registered
- Timecounter "Octeon" frequency 500000000 Hz quality 900
- Timecounters tick every 10.000 msec
- crypto: <crypto device>
- vlan: initialized, using hash tables with chaining
- IPsec: Initialized Security Association Processing.
- lo0: bpf attached
- GEOM: new disk cfid0
- usbus0: 480Mbps High Speed USB v2.0
- ugen0.1: <DWC> at usbus0
- uhub0: <DWC OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
- MAP: 0xa0000, data=0xa0000 "/dev/map/bootloader"
- MAP: a0000x900000, data=0x900000 "/dev/map/kernel"
- MAP: 9a0000x1400000, data=0x1400000 "/dev/map/rootfs"
- MAP: 1da0000x200000, data=0x200000 "/dev/map/config"
- MAP: 1fa0000x20000, data=0x20000 "/dev/map/bootloader-env"
- MAP: 1fc0000x40000, data=0x40000 "/dev/map/XXX"
- MAP: a0000x1d00000, data=0x1d00000 "/dev/map/upgrade"
- uhub0: 1 port with 1 removable, self powered
- bootpc_init: wired to interface 'octe0'
- miibus0: mii_mediachg: can't handle non-zero PHY instance 5
- octe0: link state changed to DOWN
- Sending DHCP Discover packet from interface octe0 (00:de:ad:20:75:00)
- ugen0.2: <vendor 0x0409> at usbus0
- uhub1: <vendor 0x0409 product 0x005a, class 9/0, rev 2.00/1.00, addr 2> on usbus0
- uhub1: 2 ports with 2 removable, self powered
- Received DHCP Offer packet on octe0 from 0.0.0.0 (accepted) (no root path)
- ugen0.3: <Kingston> at usbus0
- umass0: <Kingston DT 101 II, class 0/0, rev 2.00/1.10, addr 3> on usbus0
- umass0:0:0:-1: Attached to scbus0
- (probe0:umass-sim0:0:0:0): Down reving Protocol Version from 2 to 0?
- pass0 at umass-sim0 bus 0 scbus0 target 0 lun 0
- pass0: <Kingston DT 101 II PMAP> Removable Direct Access SCSI-0 device
- pass0: Serial Number 0019E00149F7B9B1E000010C
- pass0: 40.000MB/s transfers
- da0 at umass-sim0 bus 0 scbus0 target 0 lun 0
- da0: <Kingston DT 101 II PMAP> Removable Direct Access SCSI-0 device
- da0: Serial Number 0019E00149F7B9B1E000010C
- da0: 40.000MB/s transfers
- da0: 3827MB (7837696 512 byte sectors: 255H 63S/T 487C)
- GEOM: new disk da0
- MAP: No valid partition found at da0
- MAP: No valid partition found at da0s1
- MAP: No valid partition found at da0s2
- MAP: No valid partition found at da0s3
- MAP: No valid partition found at da0s4
- MAP: No valid partition found at da0s2a
- Sending DHCP Request packet from interface octe0 (00:de:ad:20:75:00)
- Received DHCP Ack packet on octe0 from 0.0.0.0 (accepted) (got root path)
- octe0 at 192.168.0.31 server 0.0.0.0
- subnet mask 255.255.255.0 router 192.168.0.90 rootfs 192.168.0.90:/usr/obj/MIPS64BE
- Adjusted interface octe0
- WARNING: WITNESS option enabled, expect reduced performance.
- Trying to mount root from nfs: []...
- NFS ROOT: 192.168.0.90:/usr/obj/MIPS64BE
- start_init: trying /sbin/init
- octe0: link state changed to UP
- Interface octe0 IP-Address 192.168.0.31 Broadcast 192.168.0.255
- Setting hostuuid: 18b36f8a-1dd2-11b2-9501-00dead207500.
- Setting hostid: 0xd225c13e.
- No suitable dump device was found.
- Entropy harvesting: interrupts ethernet point_to_point kickstart.
- Starting file system checks:
- mount_nfs: can't update /var/db/mounttab for 192.168.0.90:/usr/obj/MIPS64BE
- Mounting local file systems:.
- Setting hostname: DSR-1000N.
- Starting Network: lo0 octe0 octe1 octe2.
- lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
- options=3<RXCSUM,TXCSUM>
- inet 127.0.0.1 netmask 0xff000000
- inet6 ::1 prefixlen 128
- inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
- nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
- octe0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
- options=b<RXCSUM,TXCSUM,VLAN_MTU>
- ether 00:de:ad:20:75:00
- inet6 fe80::2de:adff:fe20:7500%octe0 prefixlen 64 tentative scopeid 0x1
- inet 192.168.0.31 netmask 0xffffff00 broadcast 192.168.0.255
- nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
- media: Ethernet autoselect (100baseTX <full-duplex>)
- status: active
- octe1: flags=8a02<BROADCAST,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
- options=b<RXCSUM,TXCSUM,VLAN_MTU>
- ether 00:de:ad:2octe1: link state changed to UP
- 0:75:00
- media: Ethernet autoselect (100baseTX <full-duplex>)
- status: active
- octe2: flags=8a02<BROADCAST,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
- options=b<RXCSUM,TXCSUM,VLAN_MTU>
- ether 00:de:ad:20:75:00
- media: Ethernet autoselect (none)
- Starting devd.
- Starting Network: octe1.
- octe1: flags=8a02<BROADCAST,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
- options=b<RXCSUM,TXCSUM,VLAN_MTU>
- ether 00:de:ad:20:75:00
- media: Ethernet autoselect (100baseTX <full-duplex>)
- status: active
- Starting Network: octe2.
- octe2: flags=8a02<BROADCAST,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
- options=b<RXCSUM,TXCSUM,VLAN_MTU>
- ether 00:de:ad:20:75:00
- media: Ethernet autoselect (none)
- Starting Network: usbus0.
- devd: cannot open pid file: Operation not supported
- add net ::ffff:0.0.0.0: gateway ::1
- add net ::0.0.0.0: gateway ::1
- add net fe80::: gateway ::1
- add net ff02::: gateway ::1
- Creating and/or trimming log files.
- Starting syslogd.
- syslogd: cannot open pid file: Operation not supported
- /etc/rc: WARNING: Dump device does not exist. Savecore not run.
- ELF ldconfig path: /lib /usr/lib /usr/lib/compat
- Clearing /tmp (X related).
- Updating motd:.
- load: 0.65 cmd: sendmail 1381 [kqread] 39.22r 0.05u 0.20s 0% 2448k
- Script /etc/rc.d/sendmail running
- Sep 28 12:34:24 DSR-1000N sm-mta[1382]: NOQUEUE: SYSERR(root): cannot flock(/var/run/sendmail.pid, fd=5, type=6, omode=40001, euid=0): Operation not supported
- Sep 28 12:35:31 DSR-1000N sm-msp-queue[1387]: p8SCZV4N001385: SYSERR(root): cannot flock(/var/spool/clientmqueue/sm-client.pid, fd=4, type=6, omode=40001, euid=25): Operation not supported
- Starting cron.
- cron: can't open or create /var/run/cron.pid: Operation not supported
- /etc/rc: WARNING: failed to start cron
- Starting background file system checks in 60 seconds.
- Wed Sep 28 12:35:35 UTC 2011
- FreeBSD/mips (DSR-1000N) (ttyu0)
- login: root
- Sep 28 12:35:38 DSR-1000N login: ROOT LOGIN (root) ON ttyu0
- FreeBSD 10.0-CURRENT (OCTEON1) #97 r0:226680M: Fri Oct 28 14:58:38 EEST 2011
- Welcome to FreeBSD!
- Before seeking technical support, please use the following resources:
- o Security advisories and updated errata information for all releases are
- at http://www.FreeBSD.org/releases/ - always consult the ERRATA section
- for your release first as it's updated frequently.
- o The Handbook and FAQ documents are at http://www.FreeBSD.org/ and,
- along with the mailing lists, can be searched by going to
- http://www.FreeBSD.org/search/. If the doc distribution has
- been installed, they're also available formatted in /usr/share/doc.
- If you still have a question or problem, please take the output of
- `uname -a', along with any relevant error messages, and email it
- as a question to the questions@FreeBSD.org mailing list. If you are
- unfamiliar with FreeBSD's directory layout, please refer to the hier(7)
- manual page. If you are not familiar with manual pages, type `man man'.
- You may also use sysinstall(8) to re-enter the installation and
- configuration utility. Edit /etc/motd to change this login announcement.
- DSR-1000N#
- DSR-1000N# ugen0.4: <Huawei Technologies> at usbus0
- Ejecting Huawei Technologies HUAWEI Mobile using method 9
- ugen0.4: <Huawei Technologies> at usbus0 (disconnected)
- ugen0.4: <Huawei Technologies> at usbus0
- u3g0: <Huawei Technologies HUAWEI Mobile, class 0/0, rev 2.00/0.00, addr 4> on usbus0
- u3g0: Found 4 ports.
- umass1: <Huawei Technologies HUAWEI Mobile, class 0/0, rev 2.00/0.00, addr 4> on usbus0
- umass1:1:1:-1: Attached to scbus1
- umass2: <Huawei Technologies HUAWEI Mobile, class 0/0, rev 2.00/0.00, addr 4> on usbus0
- umass2:2:2:-1: Attached to scbus2
- (probe0:umass-sim1:1:0:0): SCSI status error
- (probe0:umass-sim1:1:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0
- (probe0:umass-sim1:1:0:0): CAM status: SCSI Status Error
- (probe0:umass-sim1:1:0:0): SCSI status: Check Condition
- (probe0:umass-sim1:1:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (probe0:umass-sim1:1:0:0): Error 6, Unretryable error
- pass1 at umass-sim1 bus 1 scbus1 target 0 lun 0
- pass1: <HUAWEI Mass Storage 2.31> Removable CD-ROM SCSI-2 device
- pass1: 40.000MB/s transfers
- (cd0:umass-sim1:1:0:0): SCSI status error
- (cd0:umass-sim1:1:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
- (cd0:umass-sim1:1:0:0): CAM status: SCSI Status Error
- (cd0:umass-sim1:1:0:0): SCSI status: Check Condition
- (cd0:umass-sim1:1:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (cd0:umass-sim1:1:0:0): Error 6, Unretryable error
- cd0 at umass-sim1 bus 1 scbus1 target 0 lun 0
- cd0: <HUAWEI Mass Storage 2.31> Removable CD-ROM SCSI-2 device
- cd0: 40.000MB/s transfers
- cd0: Attempt to query device size failed: NOT READY, Medium not present
- GEOM: new disk cd0
- (probe0:umass-sim2:2:0:0): SCSI status error
- (probe0:umass-sim2:2:0:0): INQUIRY. CDB: 12 1 0 0 ff 0
- (probe0:umass-sim2:2:0:0): CAM status: SCSI Status Error
- (probe0:umass-sim2:2:0:0): SCSI status: Check Condition
- (probe0:umass-sim2:2:0:0): SCSI sense: ILLEGAL REQUEST asc:24,0 (Invalid field in CDB)
- (probe0:umass-sim2:2:0:0): Error 22, Unretryable error
- (probe0:umass-sim2:2:0:0): SCSI status error
- (probe0:umass-sim2:2:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0
- (probe0:umass-sim2:2:0:0): CAM status: SCSI Status Error
- (probe0:umass-sim2:2:0:0): SCSI status: Check Condition
- (probe0:umass-sim2:2:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (probe0:umass-sim2:2:0:0): Error 6, Unretryable error
- pass2 at umass-sim2 bus 2 scbus2 target 0 lun 0
- pass2: <HUAWEI TF CARD Storage 2.31> Removable Direct Access SCSI-2 device
- pass2: 40.000MB/s transfers
- (cd0:umass-sim1:1:0:0): SCSI status error
- (da1:umass-sim2:2:0:0): SCSI status error
- (da1:umass-sim2:2:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
- (da1:umass-sim2:2:0:0): CAM status: SCSI Status Error
- (da1:umass-sim2:2:0:0): SCSI status: Check Condition
- (da1:umass-sim2:2:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (da1:umass-sim2:2:0:0): Error 6, Unretryable error
- da1 at umass-sim2 bus 2 scbus2 target 0 lun 0
- da1: <HUAWEI TF CARD Storage 2.31> Removable Direct Access SCSI-2 device
- da1: 40.000MB/s transfers
- da1: Attempt to query device size failed: NOT READY, Medium not present
- (cd0:umass-sim1:1:0:0): PREVENT ALLOW MEDIUM REMOVAL. CDB: 1e 0 0 0 1 0
- (cd0:umass-sim1:1:0:0): CAM status: SCSI Status Error
- (cd0:umass-sim1:1:0:0): SCSI status: Check Condition
- (cd0:umass-sim1:1:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (cd0:umass-sim1:1:0:0): Error 6, Unretryable error
- (cd0:umass-sim1:1:0:0): SCSI status error
- (cd0:umass-sim1:1:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
- (cd0:umass-sim1:1:0:0): CAM status: SCSI Status Error
- (cd0:umass-sim1:1:0:0): SCSI status: Check Condition
- (cd0:umass-sim1:1:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (cd0:umass-sim1:1:0:0): Error 6, Unretryable error
- (cd0:umass-sim1:1:0:0): SCSI status error
- (cd0:umass-sim1:1:0:0): PREVENT ALLOW MEDIUM REMOVAL. CDB: 1e 0 0 0 1 0
- (cd0:umass-sim1:1:0:0): CAM status: SCSI Status Error
- (cd0:umass-sim1:1:0:0): SCSI status: Check Condition
- (cd0:umass-sim1:1:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (cd0:umass-sim1:1:0:0): Error 6, Unretryable error
- (cd0:umass-sim1:1:0:0): SCSI status error
- (cd0:umass-sim1:1:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
- (cd0:umass-sim1:1:0:0): CAM status: SCSI Status Error
- (cd0:umass-sim1:1:0:0): SCSI status: Check Condition
- (cd0:umass-sim1:1:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (cd0:umass-sim1:1:0:0): Error 6, Unretryable error
- (cd0:umass-sim1:1:0:0): SCSI status error
- (cd0:umass-sim1:1:0:0): PREVENT ALLOW MEDIUM REMOVAL. CDB: 1e 0 0 0 1 0
- (cd0:umass-sim1:1:0:0): CAM status: SCSI Status Error
- (cd0:umass-sim1:1:0:0): SCSI status: Check Condition
- (cd0:umass-sim1:1:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (cd0:umass-sim1:1:0:0): Error 6, Unretryable error
- (cd0:umass-sim1:1:0:0): SCSI status error
- (cd0:umass-sim1:1:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
- (cd0:umass-sim1:1:0:0): CAM status: SCSI Status Error
- (cd0:umass-sim1:1:0:0): SCSI status: Check Condition
- (cd0:umass-sim1:1:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (cd0:umass-sim1:1:0:0): Error 6, Unretryable error
- (cd0:umass-sim1:1:0:0): SCSI status error
- (cd0:umass-sim1:1:0:0): PREVENT ALLOW MEDIUM REMOVAL. CDB: 1e 0 0 0 1 0
- (cd0:umass-sim1:1:0:0): CAM status: SCSI Status Error
- (cd0:umass-sim1:1:0:0): SCSI status: Check Condition
- (cd0:umass-sim1:1:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (cd0:umass-sim1:1:0:0): Error 6, Unretryable error
- (cd0:umass-sim1:1:0:0): SCSI status error
- (cd0:umass-sim1:1:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
- (cd0:umass-sim1:1:0:0): CAM status: SCSI Status Error
- (cd0:umass-sim1:1:0:0): SCSI status: Check Condition
- (cd0:umass-sim1:1:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (cd0:umass-sim1:1:0:0): Error 6, Unretryable error
- MAP: No valid partition found at cd0
- GEOM: new disk da1
- (da1:umass-sim2:2:0:0): SCSI status error
- (da1:umass-sim2:2:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
- (da1:umass-sim2:2:0:0): CAM status: SCSI Status Error
- (da1:umass-sim2:2:0:0): SCSI status: Check Condition
- (da1:umass-sim2:2:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (da1:umass-sim2:2:0:0): Error 6, Unretryable error
- Opened disk da1 -> 6
- (da1:umass-sim2:2:0:0): SCSI status error
- (da1:umass-sim2:2:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
- (da1:umass-sim2:2:0:0): CAM status: SCSI Status Error
- (da1:umass-sim2:2:0:0): SCSI status: Check Condition
- (da1:umass-sim2:2:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (da1:umass-sim2:2:0:0): Error 6, Unretryable error
- Opened disk da1 -> 6
- (da1:umass-sim2:2:0:0): SCSI status error
- (da1:umass-sim2:2:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
- (da1:umass-sim2:2:0:0): CAM status: SCSI Status Error
- (da1:umass-sim2:2:0:0): SCSI status: Check Condition
- (da1:umass-sim2:2:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (da1:umass-sim2:2:0:0): Error 6, Unretryable error
- Opened disk da1 -> 6
- (da1:umass-sim2:2:0:0): SCSI status error
- (da1:umass-sim2:2:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
- (da1:umass-sim2:2:0:0): CAM status: SCSI Status Error
- (da1:umass-sim2:2:0:0): SCSI status: Check Condition
- (da1:umass-sim2:2:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
- (da1:umass-sim2:2:0:0): Error 6, Unretryable error
- Opened disk da1 -> 6
- DSR-1000N#
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement