Simple DMT Extraction

Simple DMT Extraction Technique

DISCLAIMER: I do not encourage you to break the law or to do anything your mother would not approve of and this guide is purely for informational purposes only. Do not listen to anything I say ever and please keep in mind the name of this tumblr. You have been warned. I am not responsible for your actions.



Things needed:

    900ml jar
    200ml jar
    100g Mimosa hostilis root bark
    150ml Naptha
    100g Lye (sodium hydroxide)
    600ml Water
    Turkey baster
    freezer
    scalpel
    safety goggles
    safety gloves

How it’s done:

Step 1 - SAFETY
Safety goggles and safety gloves should be worn while handling lye.
Long sleeve tops and trousers should also be worn for extra protection.
Lye reacts with water and becomes extremely hot, if any of the solution comes in to contact with skin or eyes, seek medical advice.

Step 2
The water should be boiled and left to cool and then the lye should be added until the solution becomes clear.
(Always add the lye to the water slowly bit by bit and not the other way round, as already mentioned the lye and water mixed together will become very hot and if the water is added to the lye it could become extremely hot and smash the jar and come into contact with skin)
Once the solution is clear the mimosa hostilis root bark is then added and submerged in the solution.
Then the lid needs to be screwed on to the jar and left at room temperature for 24 hours.

Step 3
After the 24 hours the naptha should then be added into the jar, the lid is then placed back on and the jar needs to be shaken.
The jar then needs to left alone for another 24 hours in somewhere heated, such as on top of a radiator.
Shake the jar every so often through out the 24 hours.
During this step the naptha slowly absorbs the dmt from the root bark.

Step 4
A turkey baster is then used to collect the naptha and put in to the 200ml jar.
The naptha should be completely clear, with a tint of yellow.
No brown liquid should be tolerated as this affects the dmt. If your naptha has a tint of browny orange, leave the naptha sit in the separate jar over night, the brown liquid should then separate and should be removed before moving on to the next step.


Step 5
The jar of naptha should be then placed in to the freezer for 24 hours.
The jar then needs to be taken out of the freezer and left for about half an hour so that the naptha becomes clear.
The naptha should be then be slowly poured back into the jar filled with the rootbark and left in the aquarium heater.

Step 6
There should only be crystals with a tint of yellow-white, left in the 200ml jar.
The jar needs to be left for 24 hours as it needs to dry out.
Placing the jar in front of a fan will speed things up.
Once the dmt is then dried, it can be then scraped out with a clean scalpel or knife.

Dosage, onset and smoking technique:

Threshold : 2 - 5 mg
Light : 10 - 20 mg
Moderate : 20 - 40 mg
Strong : 40 - 60 mg

Onset : 15 - 60 seconds
Duration : 5 - 20 minutes
Normal After Effects : 15 - 60 minutes

Although the internet is full of various smoking and vaporizing techniques that may or may not be more effective than others I’ve always found the simplest way to successfully smoke DMT is to put it into a normal water filtered bong with a small mixture of weed or other filler to absorb the DMT as it melts and light the bowl as usual. Take big pulls and hold them in for as long as you possibly can, if you are worried about the harshness of the smoke putting ice into the bong water helps drastically.

Useful Links: Here, Here and Here.
http://i.imgur.com/dJvwK.gif
http://www.erowid.org/chemicals/dmt/dmt.shtml
http://imgur.com/a/EqJpy