Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- TIM-1.0
- WTMI-devel-18.07.0-6050fd5
- WTMI: system early-init
- CPU VDD voltage default value: 1.108V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):711ecd3 (Marvell-armada-18.09.4)
- NOTICE: BL1: Built : 21:51:52, Sep 5 2018
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):711ecd3 (Marvell-armada-18.09.4)
- NOTICE: BL2: Built : 21:51:55, Sep 5 2018
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):711ecd3 (Marvell-armada-18.09.4)
- NOTICE: BL31: Built : 21:52:00, Sep
- U-Boot 2017.03-armada-18.09.1-ga92bd86-armbian (Sep 05 2018 - 21:49:34 +0200)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 600 [MHz]
- L2 600 [MHz]
- NB AXI 150 [MHz]
- SB AXI 200 [MHz]
- DDR 600 [MHz]
- DRAM: 1 GiB
- U-Boot DT blob at : 000000003f7142d8
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- SATA link 0 timeout.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- PCIE-0: Link down
- MMC: sdhci@d0000: 0
- SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB
- Net: eth0: neta@30000 [PRIME]
- Hit any key to stop autoboot: 0
- TIM-1.0
- WTMI-devel-18.07.0-6050fd5
- WTMI: system early-init
- CPU VDD voltage default value: 1.108V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):711ecd3 (Marvell-armada-18.09.4)
- NOTICE: BL1: Built : 21:52:08, Sep 5 2018
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):711ecd3 (Marvell-armada-18.09.4)
- NOTICE: BL2: Built : 21:52:11, Sep 5 2018
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):711ecd3 (Marvell-armada-18.09.4)
- NOTICE: BL31: Built : 21:52:16
- U-Boot 2017.03-armada-18.09.1-ga92bd86-armbian (Sep 05 2018 - 21:49:34 +0200)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 800 [MHz]
- L2 800 [MHz]
- NB AXI 200 [MHz]
- SB AXI 250 [MHz]
- DDR 800 [MHz]
- DRAM: 1 GiB
- U-Boot DT blob at : 000000003f7142d8
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- SATA link 0 timeout.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- PCIE-0: Link down
- MMC: sdhci@d0000: 0
- SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB
- Net: eth0: neta@30000 [PRIME]
- Hit any key to stop autoboot: 0
- TIM-1.0
- WTMI-devel-18.07.0-6050fd5
- WTMI: system early-init
- CPU VDD voltage default value: 1.155V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):711ecd3 (Marvell-armada-18.09.4)
- NOTICE: BL1: Built : 21:52:23, Sep 5 2018
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):711ecd3 (Marvell-armada-18.09.4)
- NOTICE: BL2: Built : 21:52:26, Sep 5 2018
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):711ecd3 (Marvell-armada-18.09.4)
- NOTICE: BL31: Built : 21:5
- U-Boot 2017.03-armada-18.09.1-ga92bd86-armbian (Sep 05 2018 - 21:49:34 +0200)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 1000 [MHz]
- L2 1000 [MHz]
- NB AXI 250 [MHz]
- SB AXI 250 [MHz]
- DDR 800 [MHz]
- DRAM: 1 GiB
- U-Boot DT blob at : 000000003f7142d8
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- SATA link 0 timeout.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- PCIE-0: Link down
- MMC: sdhci@d0000: 0
- SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB
- Net: eth0: neta@30000 [PRIME]
- Hit any key to stop autoboot: 0
- TIM-1.0
- WTMI-devel-18.07.0-6050fd5
- WTMI: system early-init
- CPU VDD voltage default value: 1.202V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):711ecd3 (Marvell-armada-18.09.4)
- NOTICE: BL1: Built : 21:52:39, Sep 5 2018
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):711ecd3 (Marvell-armada-18.09.4)
- NOTICE: BL2: Built : 21:52:42, Sep 5 2018
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):711ecd3 (Marvell-armada-18.09.4)
- NOTICE: BL31: Built : 21
- U-Boot 2017.03-armada-18.09.1-ga92bd86-armbian (Sep 05 2018 - 21:49:34 +0200)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 1200 [MHz]
- L2 1200 [MHz]
- NB AXI 300 [MHz]
- SB AXI 250 [MHz]
- DDR 750 [MHz]
- DRAM: 1 GiB
- U-Boot DT blob at : 000000003f7142d8
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- SATA link 0 timeout.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- PCIE-0: Link down
- MMC: sdhci@d0000: 0
- SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB
- Net: eth0: neta@30000 [PRIME]
- Hit any key to stop autoboot: 0
- arvell>> printenv
- arch=arm
- baudrate=115200
- board=mvebu_armada-37xx
- board_name=mvebu_armada-37xx
- boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}
- boot_efi_binary=load ${devtype} ${devnum}:${distro_bootpart} ${kernel_addr_r} efi/boot/bootaa64.efi; if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r};else bootefi ${kernel_addr_i
- boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}extlinux/extlinux.conf
- boot_net_pci_enum=pci enum
- boot_net_usb_start=usb start
- boot_prefixes=/ /boot/
- boot_script_dhcp=boot.scr.uimg
- boot_scripts=boot.scr.uimg boot.scr
- boot_targets=mmc1 mmc0 usb0 scsi0 pxe dhcp
- bootcmd=run get_images; run set_bootargs; run load_script;booti $kernel_addr $ramfs_addr $fdt_addr
- bootcmd_dhcp=run boot_net_usb_start; run boot_net_pci_enum; if dhcp ${scriptaddr} ${boot_script_dhcp}; then source ${scriptaddr}; fi;setenv efi_fdtfile ${fdtfile}; setenv efi_old_vci ${bootp_vci};set;
- bootcmd_mmc0=setenv devnum 0; run mmc_boot
- bootcmd_mmc1=setenv devnum 1; run mmc_boot
- bootcmd_nfs=run get_images; run set_bootargs; booti $kernel_addr_r $ramdisk_addr_r $fdt_addr_r
- bootcmd_pxe=run boot_net_usb_start; run boot_net_pci_enum; dhcp; if pxe get; then pxe boot; fi
- bootcmd_scsi0=setenv devnum 0; run scsi_boot
- bootcmd_usb0=setenv devnum 0; run usb_boot
- bootdelay=2
- console=console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000
- cpu=armv8
- distro_bootcmd=setenv scsi_need_init; for target in ${boot_targets}; do run bootcmd_${target}; done
- efi_dtb_prefixes=/ /dtb/ /dtb/current/
- eth1addr=00:51:82:11:22:01
- eth2addr=00:51:82:11:22:02
- eth3addr=00:51:82:11:22:03
- ethact=neta@30000
- ethaddr=00:51:82:11:22:00
- ethprime=eth0
- extra_params=pci=pcie_bus_safe
- fdt_addr_r=0x6f00000
- fdt_high=0xffffffffffffffff
- fdt_name=fdt.dtb
- fdtcontroladdr=3f7142d8
- gatewayip=10.4.50.254
- get_images=tftpboot $kernel_addr_r $image_name; tftpboot $fdt_addr_r $fdt_name; run get_ramdisk
- get_ramdisk=if test "${ramdisk_name}" != "-"; then tftpboot $ramdisk_addr_r $ramdisk_name; else setenv ramdisk_addr_r -;fi
- hostname=marvell
- image_name=boot/Image
- initrd_addr=0x1100000
- initrd_size=0x2000000
- ipaddr=0.0.0.0
- kernel_addr_r=0x7000000
- load_efi_dtb=load ${devtype} ${devnum}:${distro_bootpart} ${fdt_addr_r} ${prefix}${efi_fdtfile}
- load_script=if test -e mmc 0:1 boot/boot.scr; then echo "... booting from SD";setenv boot_interface mmc;else echo "... booting from USB/SATA";usb start;setenv boot_interface usb;fi;if test -e $boot_ii
- loadaddr=0x7000000
- mmc_boot=if mmc dev ${devnum}; then setenv devtype mmc; run scan_dev_for_boot_part; fi
- netdev=eth0
- netmask=255.255.255.0
- pxefile_addr_r=0x6e00000
- ramdisk_addr_r=0xa000000
- ramdisk_name=-
- root=root=/dev/nfs rw
- rootpath=/srv/nfs
- scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;run scan_dev_for_efi;
- scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_boote
- scan_dev_for_efi=setenv efi_fdtfile ${fdtfile}; for prefix in ${efi_dtb_prefixes}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${efi_fdtfile}; then run load_efi_dtb; fi;done;if tese
- scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}extlinux/extlinux.conf; then echo Found ${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED: contii
- scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echoe
- scriptaddr=0x6d00000
- scsi_boot=run scsi_init; if scsi dev ${devnum}; then setenv devtype scsi; run scan_dev_for_boot_part; fi
- scsi_init=if ${scsi_need_init}; then setenv scsi_need_init false; scsi scan; fi
- serverip=0.0.0.0
- set_bootargs=setenv bootargs $console $root ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:none nfsroot=$serverip:$rootpath $extra_params $cpuidle
- soc=mvebu
- stderr=serial@12000
- stdin=serial@12000
- stdout=serial@12000
- usb_boot=usb start; if usb dev ${devnum}; then setenv devtype usb; run scan_dev_for_boot_part; fi
- vendor=Marvell
- Environment size: 5311/65532 bytes
- Marvell>>
- TIM-1.0
- WTMI-devel-18.07.0-6050fd5
- WTMI: system early-init
- CPU VDD voltage default value: 1.155V
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):711ecd3 (Marvell-armada-18.09.4)
- NOTICE: BL1: Built : 21:52:23, Sep 5 2018
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):711ecd3 (Marvell-armada-18.09.4)
- NOTICE: BL2: Built : 21:52:26, Sep 5 2018
- NOTICE: BL1: Booting BL31
- NOTICE: BL31: v1.5(release):711ecd3 (Marvell-armada-18.09.4)
- NOTICE: BL31: Built : 21:5
- U-Boot 2017.03-armada-18.09.1-ga92bd86-armbian (Sep 05 2018 - 21:49:34 +0200)
- Model: Marvell Armada 3720 Community Board ESPRESSOBin
- CPU 1000 [MHz]
- L2 1000 [MHz]
- NB AXI 250 [MHz]
- SB AXI 250 [MHz]
- DDR 800 [MHz]
- DRAM: 1 GiB
- U-Boot DT blob at : 000000003f7142d8
- Comphy chip #0:
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- SATA link 0 timeout.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- PCIE-0: Link down
- MMC: sdhci@d0000: 0
- SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB
- Net: eth0: neta@30000 [PRIME]
- Hit any key to stop autoboot: 0
- *** ERROR: `serverip' not set
- *** ERROR: `serverip' not set
- ... booting from SD
- 1176 bytes read in 6 ms (191.4 KiB/s)
- ## Executing script at 00800000
- 172 bytes read in 3 ms (55.7 KiB/s)
- ext4load - load binary file from a Ext4 filesystem
- Usage:
- ext4load <interface> [<dev[:part]> [addr [filename [bytes [pos]]]]]
- - load binary file 'filename' from 'dev' on 'interface'
- to address 'addr' from ext4 filesystem
- 4589284 bytes read in 208 ms (21 MiB/s)
- ext4load - load binary file from a Ext4 filesystem
- Usage:
- ext4load <interface> [<dev[:part]> [addr [filename [bytes [pos]]]]]
- - load binary file 'filename' from 'dev' on 'interface'
- to address 'addr' from ext4 filesystem
- ext4load - load binary file from a Ext4 filesystem
- Usage:
- ext4load <interface> [<dev[:part]> [addr [filename [bytes [pos]]]]]
- - load binary file 'filename' from 'dev' on 'interface'
- to address 'addr' from ext4 filesystem
- Bad Linux ARM64 Image magic!
- Bad Linux ARM64 Image magic!
- Marvell>>
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement