U-Boot 2009.08 (Nov 04 2012 - 19:53:53) Avocent (0.0.3) EVB, Build: jenkins-idrac-yocto-release-88

CPU: SH-4A
BOARD: R0P7757LC00xxRL (C0 step) board
BOOT: Secure, HRK generated
DRAM:  240MB
  (240MB of 256MB total DRAM is available on U-Boot)
ENV:   Using primary env area.
In:    serial
Out:   serial
Err:   serial
PCIe:  Bridge loaded with 0x18000 bytes
WDT2:  Booted Lower Vector, 'uboot1'
sh_mmcif: 0, sh-sdhi: 1
Net:   sh_eth.0, sh_g_eth.0
INFO: 00:002 Start-up -to- util_idrac_main()
INFO: 00:004 U-Boot 2009.08 (Nov 04 2012 - 19:53:53) Avocent (0.0.3) EVB
INFO: 00:007 U-Boot checkin date(07-30-2012) Version(1.0.179)
INFO: 00:006 iDRAC PPID <NULL>
INFO: 00:003 SPI NOR init 4096 KiB MX25L3206E bus=0 cs=0, speed=1000000, mode=3
INFO: 00:007 SH-4A Product: Major Ver=0x31  Minor Ver=0x13 C3 Little endian
             Family=0x10    Major Ver=0x30  Minor Ver=0x0b
PASS: 00:016 Dedicated monolithic mgmt NIC disabled
INFO: 00:128 BCM54610 OUI=0x3fffff  Model=0x3f  Revision=0x0f PhyAddr=1
INFO: 00:092 SD CARD:   Device: sh-sdhi   Manufacturer ID: 3   OEM: 5344
             Name: SD01G   Tran Speed: 25000000   Rd Block Len: 512
             SD version 1.10   High Capacity: No   Capacity: 1015808000
sh_mmcif: Cmd(d'1) err
Card did not respond to voltage select!
INFO: 00:032 EMMC:   Device: sh_mmcif   Manufacturer ID: 0   OEM: 0
             Name:
INFO: 00:008 CPLD: Major Ver=0x1  Minor Ver=0x0  Maint Ver=0x3
             Planar: Type=0x02  Rev=0x8  Rework=0x0  Scratch/PathRetry=0x00
PASS: 00:014 Coin cell detected good,  AD=0x399 low water=0x2c1
PASS: 00:008 PCIe C0 Ver=0.13 MCTP en, CRC=0x19592849 @0x8efbf4fc cnt=0x18000
INFO: 00:007 Init PCIe mailbox(PCIe 0xFFEE0150=0x40010000)
INFO: 00:006 mode=normal
INFO: 00:002 reset_cause=recover
PASS: 00:005 Booted Lower Vector, 'uboot1' wdt2cnt=0
INFO: 00:005 wdt0cnt=1
PASS: 00:002 SMR0 no sermux env, default 0xd4
INFO: 00:005 GRACR=0x3c HISEL=0x00 SIRQCR5_D=0x03 SIRQCR6_D=0x01 LADMSK0=0xff2
             MRSTCR0=0xfedffe7f MRSTCR1=0xfff3ff0f MRSTCR2=0x7f80feff
             BARMAP=0x1 BCR=0x85000000 NCER=0x01fc NCMCR=0x0006 NCCSR=0x0303
PASS: 00:021 etherc0=78:45:C4:F5:23:F9
             getherc0=78:45:C4:F5:23:FA
INFO: 00:007 Fan logic is not modified on Non-AC power up
INFO: 00:053 Env and backup CRC'ed ok
sh_mmcif: Cmd(d'1) err
Card did not respond to voltage select!
sh_mmcif: Cmd(d'1) err
Card did not respond to voltage select!
sh_mmcif: Cmd(d'1) err
Card did not respond to voltage select!
sh_mmcif: Cmd(d'16) err
set read bl len failed
*** fail to read block from device ***
*** can't read from device 1 ***
*** create default partitions ***
sh_mmcif: Cmd(d'1) err
Card did not respond to voltage select!
sh_mmcif: Cmd(d'16) err
set write bl len failed
*** fail to write block to device ***
*** can't write to device 1 ***
FAIL: 00:086 fwu_init() failure
INFO: 00:004 Sync eMMC/SPI NOR/Alternate u-boot images
FAIL: 00:005 ...eMMC/MBR does not have a bootable partition
FAIL: 00:006 verify_os_images(): eMMC/MBR does not have a bootable partition
FAIL: 00:007 Boot device=emmc  Boot partition-1/No bootable partition
             Boot Path Retry:P1/N=0 P5/N-1=0  Invalid boot partition
INFO: 00:014 Sync eMMC/SPI NOR/Alternate u-boot images
FAIL: 00:005 ...eMMC/MBR does not have a bootable partition
FAIL: 00:006 verify_os_images(): eMMC/MBR does not have a bootable partition
FAIL: 00:007 Boot device=emmc  Boot partition-1/No bootable partition
             Boot Path Retry:P1/N=0 P5/N-1=0  Invalid boot partition
INFO: 00:075 No 'userexe' defined
INFO: 00:000 00:658
Hit any key to stop autoboot:  0
WDT2: Disable in abortboot()
OSWDT: Disable in abortboot()
CPLD_BMCRDY: Enable BMC_MIN_RDY in abortboot().  Prevent BIOS reset.

NOTE: After stopping u-boot in this development mode.  You may need to
      warm/cold reset the server when booting iDRAC manually as BIOS
      may have already viewed iDRAC as unresponsive.



RECOVER:Max retries occured for both N/N-1 paths, OR forced recover.

iDRAC7=> util recover -emmc -from sd -f firmimg.d7


UTIL RECOVER:Transport:sd  TargetMMC:EMMC  File:firmimg.d7
reading firmimg.d7

112384230 bytes read
UTIL RECOVER:SD load passed from FAT fs.
UTIL RECOVER:Transport time [sec:mil]: 19:913

Clear OS images in partition/s.
Clear kernelN, rootfsN, ubootN
'EMMC' blk size=[0x200][512]  Erase to 0xffffffff
Mem buf size=[0x06000000][100663296]  Total bytes=[0x08000000][134217728]
blocks[0x1:0x40001][1:262145]
sh_mmcif: Cmd(d'1) erruf[0x88000000]..fill buffer..erase/write
Card did not respond to voltage select!
sh_mmcif: Cmd(d'16) err
set write bl len failed
util flash:
Failure writing blocks [1:196609] RC=0xffffffac
UTIL PASS
iDRAC7=>