U-Boot 2014.04 (Sep 26 2017 - 12:17:58)

CPU:   Freescale i.MX6SOLO rev1.3 at 792 MHz
CPU:   Temperature 36 C, calibration data: 0x59250c69
Reset cause: POR
Board: SK-iMX6-OEM
DRAM:  512 MiB
NAND:  1024 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment

Net:   FEC
Normal Boot
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x1000000, size 0x600000
 6291456 bytes read: OK

NAND read: device 0 offset 0x1800000, size 0x19000
 102400 bytes read: OK
Kernel image @ 0x12000000 [ 0x000000 - 0x4f4098 ]
## Flattened Device Tree blob at 12800000
   Booting using the fdt blob at 0x12800000
   Using Device Tree in place at 12800000, end 1280b42e

Starting kernel ...

Booting Linux on physical CPU 0x0
Linux version 3.14.14 (root@imx6-build-machine) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #133 SMP Tue May 23 15:08:22 MSK 2017
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Starterkit SK-iMX6-OEM Board
cma: CMA: reserved 320 MiB at 1c000000
Memory policy: Data cache writeback
CPU: All CPU(s) started in SVC mode.
PERCPU: Embedded 8 pages/cpu @8bb39000 s8832 r8192 d15744 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line: console=ttymxc0,115200 mtdparts=gpmi-nand:16M(boot),8M(kernel),2M(dtb),512M(rootfs),-(userdata) ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rootwait rw video=mxcfb0:dev=ldb,SK-ATM0704,if=RGB24 video=mxcfb1:dev=lcd,SK-ATM0704,if=RGB24 consoleblank=0
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 181732K/524288K available (6585K kernel code, 249K rwdata, 1988K rodata, 292K init, 425K bss, 342556K reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xa0800000 - 0xff000000   (1512 MB)
    lowmem  : 0x80000000 - 0xa0000000   ( 512 MB)
    pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
    modules : 0x7f000000 - 0x7fe00000   (  14 MB)
      .text : 0x80008000 - 0x808677cc   (8574 kB)
      .init : 0x80868000 - 0x808b1280   ( 293 kB)
      .data : 0x808b2000 - 0x808f0720   ( 250 kB)
       .bss : 0x808f0728 - 0x8095ae30   ( 426 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
        RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 16 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76050001
sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655765682ns
Console: colour dummy device 80x30
Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Initializing cgroup subsys bfqio
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x106489c8 - 0x10648a20
CPU1: failed to boot: -38
Brought up 1 CPUs
SMP: Total of 1 processors activated.
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
pinctrl core: initialized pinctrl subsystem
regulator-dummy: no parameters
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
CPU identified as i.MX6DL, silicon rev 1.3
Use WDOG1 as reset source
syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered
vdd1p1: 800 <--> 1375 mV at 1125 mV
vdd3p0: 2800 <--> 3150 mV at 3000 mV
vdd2p5: 2000 <--> 2750 mV at 2425 mV
vddarm: 725 <--> 1450 mV at 1150 mV
vddpu: 725 <--> 1450 mV
vddsoc: 725 <--> 1450 mV at 1175 mV
syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered
syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered
imx6q_ocram_suspend_init: invalid argument!
imx6_pm_common_init: failed to initialize ocram suspend -22!
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
imx6dl-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
bio: create slab <bio-0> at 0
mxs-dma 110000.dma-apbh: initialized
3P3V: 3300 mV
usb_h1_vbus: 5000 mV
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
usbphy_nop1.11 supply vcc not found, using dummy regulator
usbphy_nop2.12 supply vcc not found, using dummy regulator
i2c i2c-1: IMX I2C adapter registered
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
MIPI CSI2 driver module loaded
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.18
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Switched to clocksource mxc_timer1
cfg80211: Calling CRDA to update world regulatory domain
imx6q-pcie 1ffc000.pcie: phy link never came up
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io  0x1000-0x10000]
pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
pci 0000:00:00.0: BAR 0: assigned [mem 0x01000000-0x010fffff]
pci 0000:00:00.0: BAR 6: assigned [mem 0x01100000-0x0110ffff pref]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0: PCI bridge to [bus 01]
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: enabled with ARMv7_Cortex_A9 PMU driver, 7 counters available
pureg-dummy: no parameters
Bus freq driver module loaded
futex hash table entries: 512 (order: 3, 32768 bytes)
zbud: loaded
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
fuse init (API version 7.22)
msgmni has been set to 994
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered
io scheduler bfq registered (default)
BFQ I/O-scheduler version: v7r5
pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
backlight.17 supply power not found, using dummy regulator
mxc_sdc_fb fb.21: register mxc display driver ldb
fbcvt: Invalid input parameters
imx-ipuv3 2400000.ipu: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
Console: switching to colour frame buffer device 240x45
mxc_sdc_fb fb.22: register mxc display driver lcd
mxc_sdc_fb fb.22: NO mxc display driver found!
imx-sdma 20ec000.sdma: no iram assigned, using external mem
imx-sdma 20ec000.sdma: loaded firmware 1.1
imx-sdma 20ec000.sdma: initialized
Serial: IMX driver
2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58, base_baud = 5000000) is a IMX
console [ttymxc0] enabled
21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59, base_baud = 5000000) is a IMX
serial: Freescale lpuart driver
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized vivante 1.0.0 20120216 on minor 0
brd: module loaded
loop: module loaded
nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xd3
nand: Macronix MX60LF8G18AC
nand: 1024MiB, SLC, page size: 2048, OOB size: 64
gpmi-nand 112000.gpmi-nand: mode:5 ,failed in set feature.
Bad block table found at page 524224, version 0x02
Bad block table found at page 524160, version 0x02
nand_read_bbt: bad block at 0x00000aaa0000
nand_read_bbt: bad block at 0x000027f20000
nand_read_bbt: bad block at 0x00002d5c0000
nand_read_bbt: bad block at 0x0000303e0000
nand_read_bbt: bad block at 0x000033f60000
nand_read_bbt: bad block at 0x00003ef60000
5 cmdlinepart partitions found on MTD device gpmi-nand
Creating 5 MTD partitions on "gpmi-nand":
0x000000000000-0x000001000000 : "boot"
0x000001000000-0x000001800000 : "kernel"
0x000001800000-0x000001a00000 : "dtb"
0x000001a00000-0x000021a00000 : "rootfs"
0x000021a00000-0x000040000000 : "userdata"
gpmi-nand 112000.gpmi-nand: driver registered.
spi_imx 2008000.ecspi: probed
spi_imx 2014000.ecspi: probed
CAN device driver interface
2090000.flexcan supply xceiver not found, using dummy regulator
flexcan 2090000.flexcan: device registered (reg_base=a0a50000, irq=142)
2094000.flexcan supply xceiver not found, using dummy regulator
flexcan 2094000.flexcan: device registered (reg_base=a0a58000, irq=143)
2188000.ethernet supply phy not found, using dummy regulator
libphy: fec_enet_mii_bus: probed
fec 2188000.ethernet eth0: registered PHC device 0
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
2184800.usbmisc supply vbus-wakeup not found, using dummy regulator
2184000.usb supply vbus not found, using dummy regulator
ci_hdrc ci_hdrc.1: doesn't support gadget
ci_hdrc ci_hdrc.1: EHCI Host Controller
ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ads7846 spi0.0: touchscreen, irq 271
input: ADS7846 Touchscreen as /devices/soc0/soc.1/2000000.aips-bus/2000000.spba-bus/2008000.ecspi/spi_master/spi0/spi0.0/input/input0
ads7846 spi3.0: touchscreen, irq 169
input: ADS7846 Touchscreen as /devices/soc0/soc.1/2000000.aips-bus/2000000.spba-bus/2014000.ecspi/spi_master/spi3/spi3.0/input/input1
snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc0
i2c /dev entries driver
mxc_v4l2_output v4l2_out.26: V4L2 device registered as video16
mxc_v4l2_output v4l2_out.26: V4L2 device registered as video17
uvcvideo: Unable to create debugfs directory
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
platform tempmon.10: Driver imx_thermal requests probe deferral
imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: no vqmmc regulator found
2190000.usdhc supply card-external-vcc not found, using dummy regulator
mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
mmc1: no vqmmc regulator found
2194000.usdhc supply card-external-vcc not found, using dummy regulator
mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
galcore: clk_get vg clock failed, disable vg!
Galcore version 5.0.11.33433
mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
mxc_asrc 2034000.asrc: mxc_asrc registered
mxc_vpu 2040000.vpu: VPU initialized
mxc_hdmi_cec hdmi_cec.16: HDMI CEC initialized
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
fsl-hdmi-dai hdmi_audio.15: failed to probe. Load HDMI-video first.
fsl-hdmi-dai: probe of hdmi_audio.15 failed with error -12
tlv320aic23-codec 1-001a: codec clk_frequency = 12000000
imx-tlv320 sound.23: tlv320aic23-hifi <-> 202c000.ssi mapping ok
imx-spdif sound-spdif.25: ASoC: CPU DAI (null) not registered
imx-spdif sound-spdif.25: snd_soc_register_card failed: -517
platform sound-spdif.25: Driver imx-spdif requests probe deferral
imx-audio-hdmi sound-hdmi.24: initialize HDMI-audio failed. load HDMI-video first!
TCP: cubic registered
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
8021q: 802.1Q VLAN Support v1.8
lib80211: common routines for IEEE802.11 drivers
Key type dns_resolver registered
regulator-dummy: disabling
imx-spdif sound-spdif.25: ASoC: CPU DAI (null) not registered
imx-spdif sound-spdif.25: snd_soc_register_card failed: -517
platform sound-spdif.25: Driver imx-spdif requests probe deferral
UBI: attaching mtd3 to ubi0
random: nonblocking pool is initialized
UBI: scanning is finished
UBI: attached mtd3 (name "rootfs", size 512 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 4095, bad PEBs: 1, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 3/2, WL threshold: 256, image sequence number: 500379069
UBI: available PEBs: 0, total reserved PEBs: 4095, PEBs reserved for bad PEB handling: 159
UBI: background thread "ubi_bgt0d" started, PID 106
snvs_rtc 20cc034.snvs-rtc-lp: setting system clock to 1970-01-01 00:00:06 UTC (6)
ALSA device list:
  #0: imx-tlv320
UBIFS: background thread "ubifs_bgt0_0" started, PID 107
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 497238016 bytes (474 MiB, 3916 LEBs), journal size 24887296 bytes (23 MiB, 196 LEBs)
UBIFS: reserved for root: 4952683 bytes (4836 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID 7F04D275-BB38-43A1-BB03-9700AEC88BC7, small LPT model
VFS: Mounted root (ubifs filesystem) on device 0:11.
devtmpfs: mounted
Freeing unused kernel memory: 292K (80868000 - 808b1000)
UBIFS error (pid 1): ubifs_read_node: bad node type (255 but expected 1)
UBIFS error (pid 1): ubifs_read_node: bad node at LEB 134:61936, LEB mapping status 0
Not a node, first 24 bytes:
00000000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff                          ........................
CPU: 0 PID: 1 Comm: init Not tainted 3.14.14 #133
[<80015388>] (unwind_backtrace) from [<80011690>] (show_stack+0x10/0x14)
[<80011690>] (show_stack) from [<80642d74>] (dump_stack+0x88/0x98)
[<80642d74>] (dump_stack) from [<801d1094>] (ubifs_read_node+0x230/0x298)
[<801d1094>] (ubifs_read_node) from [<801ed99c>] (ubifs_tnc_read_node+0x120/0x12c)
[<801ed99c>] (ubifs_tnc_read_node) from [<801d45cc>] (ubifs_tnc_locate+0x1a0/0x1cc)
[<801d45cc>] (ubifs_tnc_locate) from [<801c6f7c>] (do_readpage+0x128/0x3d0)
[<801c6f7c>] (do_readpage) from [<801c8320>] (ubifs_readpage+0x38/0x4a0)
[<801c8320>] (ubifs_readpage) from [<8009a70c>] (filemap_fault+0x26c/0x448)
[<8009a70c>] (filemap_fault) from [<800b6410>] (__do_fault+0x6c/0x5a0)
[<800b6410>] (__do_fault) from [<800b9a28>] (handle_mm_fault+0x104/0x8d0)
[<800b9a28>] (handle_mm_fault) from [<8001a610>] (do_page_fault+0x184/0x3f0)
[<8001a610>] (do_page_fault) from [<80008454>] (do_PrefetchAbort+0x34/0x9c)
[<80008454>] (do_PrefetchAbort) from [<80012514>] (ret_from_exception+0x0/0x10)
Exception stack(0x8804bfb0 to 0x8804bff8)
bfa0:                                     00000001 7ea1df14 7ea1df1c 000937b8
bfc0: 00000000 0005dcb9 76eed000 00000000 00000000 00000000 76f19000 00000000
bfe0: 76e17259 7ea1ddc0 76e172af 0005dcb8 600d0030 ffffffff
UBIFS error (pid 1): do_readpage: cannot read page 77 of inode 736, error -22
UBIFS error (pid 1): ubifs_read_node: bad node type (255 but expected 1)
UBIFS error (pid 1): ubifs_read_node: bad node at LEB 134:61936, LEB mapping status 0
Not a node, first 24 bytes:
00000000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff                          ........................
CPU: 0 PID: 1 Comm: init Not tainted 3.14.14 #133
[<80015388>] (unwind_backtrace) from [<80011690>] (show_stack+0x10/0x14)
[<80011690>] (show_stack) from [<80642d74>] (dump_stack+0x88/0x98)
[<80642d74>] (dump_stack) from [<801d1094>] (ubifs_read_node+0x230/0x298)
[<801d1094>] (ubifs_read_node) from [<801ed99c>] (ubifs_tnc_read_node+0x120/0x12c)
[<801ed99c>] (ubifs_tnc_read_node) from [<801d45cc>] (ubifs_tnc_locate+0x1a0/0x1cc)
[<801d45cc>] (ubifs_tnc_locate) from [<801c6f7c>] (do_readpage+0x128/0x3d0)
[<801c6f7c>] (do_readpage) from [<801c8320>] (ubifs_readpage+0x38/0x4a0)
[<801c8320>] (ubifs_readpage) from [<8009a610>] (filemap_fault+0x170/0x448)
[<8009a610>] (filemap_fault) from [<800b6410>] (__do_fault+0x6c/0x5a0)
[<800b6410>] (__do_fault) from [<800b9a28>] (handle_mm_fault+0x104/0x8d0)
[<800b9a28>] (handle_mm_fault) from [<8001a610>] (do_page_fault+0x184/0x3f0)
[<8001a610>] (do_page_fault) from [<80008454>] (do_PrefetchAbort+0x34/0x9c)
[<80008454>] (do_PrefetchAbort) from [<80012514>] (ret_from_exception+0x0/0x10)
Exception stack(0x8804bfb0 to 0x8804bff8)
bfa0:                                     00000001 7ea1df14 7ea1df1c 000937b8
bfc0: 00000000 0005dcb9 76eed000 00000000 00000000 00000000 76f19000 00000000
bfe0: 76e17259 7ea1ddc0 76e172af 0005dcb8 600d0030 ffffffff
UBIFS error (pid 1): do_readpage: cannot read page 77 of inode 736, error -22
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007