Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 1.1.3 (Sep 22 2016 - 14:56:24)
- Board: Ralink APSoC DRAM: 64 MB
- relocate_code Pointer at: 83fb8000
- flash manufacture id: ef, device id 40 18
- find flash: W25Q128BV
- *** Warning - bad CRC, using default environment
- ============================================
- Ralink UBoot Version: 5.0.0.0
- --------------------------------------------
- ASIC 7628_MP (Port5<->None)
- DRAM component: 512 Mbits DDR, width 16
- DRAM bus: 16 bit
- Total memory: 64 MBytes
- Flash component: SPI Flash
- Date:Sep 22 2016 Time:14:56:24
- ============================================
- icache: sets:512, ways:4, linesz:32 ,total:65536
- dcache: sets:256, ways:4, linesz:32 ,total:32768
- ##### The CPU freq = 580 MHZ ####
- estimate memory size =64 Mbytes
- RESET MT7628 PHY!!!!!!
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 7: Load Boot Loader code then write to Flash via Serial.
- 9: Load Boot Loader code then write to Flash via TFTP.
- default: 3
- 4 3 2 1 0
- 3: System Boot system code via Flash.
- ## Booting image at bc050000 ...
- Image Name: MIPS OpenWrt Linux-4.14.121
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 1675414 Bytes = 1.6 MB
- Load Address: 80000000
- Entry Point: 80000000
- Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80000000) ...
- ## Giving linux memsize in MB, 64
- Starting kernel ...
- [ 0.000000] Linux version 4.14.121 (buildbot@slashdirt-03) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10085-8128a7e)) #0 Tue May 28 11:18:58 2019
- [ 0.000000] Board has DDR2
- [ 0.000000] Analog PMU set to hw control
- [ 0.000000] Digital PMU set to hw control
- [ 0.000000] SoC Type: MediaTek MT7628AN ver:1 eco:2
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
- [ 0.000000] MIPS: machine is SKYLAB SKW92A
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x480 with crng_init=0
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
- [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Writing ErrCtl register=00060a50
- [ 0.000000] Readback ErrCtl register=00060a50
- [ 0.000000] Memory: 59464K/65536K available (3918K kernel code, 186K rwdata, 908K rodata, 164K init, 207K bss, 6072K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS: 256
- [ 0.000000] intc: using register map from devicetree
- [ 0.000000] CPU Clock: 580MHz
- [ 0.000000] timer_probe: no matching timers found
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
- [ 0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
- [ 0.015380] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
- [ 0.087585] pid_max: default: 32768 minimum: 301
- [ 0.096945] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.109908] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.129479] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.148859] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.160967] pinctrl core: initialized pinctrl subsystem
- [ 0.173758] NET: Registered protocol family 16
- [ 0.207649] mt7621_gpio 10000600.gpio: registering 32 gpios
- [ 0.218857] mt7621_gpio 10000600.gpio: registering 32 gpios
- [ 0.230000] mt7621_gpio 10000600.gpio: registering 32 gpios
- [ 0.245912] clocksource: Switched to clocksource MIPS
- [ 0.257029] NET: Registered protocol family 2
- [ 0.266549] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.280258] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.292766] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.305460] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.316926] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.329520] NET: Registered protocol family 1
- [ 0.341362] Crashlog allocated RAM at address 0x3f00000
- [ 0.353216] workingset: timestamp_bits=30 max_order=14 bucket_order=0
- [ 0.371834] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.383278] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.412790] io scheduler noop registered
- [ 0.420466] io scheduler deadline registered (default)
- [ 0.431518] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.447029] console [ttyS0] disabled
- [ 0.453996] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
- [ 0.471922] console [ttyS0] enabled
- [ 0.471922] console [ttyS0] enabled
- [ 0.485615] bootconsole [early0] disabled
- [ 0.485615] bootconsole [early0] disabled
- [ 0.502076] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A
- [ 0.520143] cacheinfo: Failed to find cpu0 device node
- [ 0.530356] cacheinfo: Unable to detect cache hierarchy for CPU 0
- [ 0.543201] spi-mt7621 10000b00.spi: sys_freq: 193333333
- [ 0.570000] m25p80 spi0.0: w25q128 (16384 Kbytes)
- [ 0.579377] 4 fixed-partitions partitions found on MTD device spi0.0
- [ 0.591966] Creating 4 MTD partitions on "spi0.0":
- [ 0.601467] 0x000000000000-0x000000030000 : "u-boot"
- [ 0.612235] 0x000000030000-0x000000040000 : "u-boot-env"
- [ 0.623666] 0x000000040000-0x000000050000 : "factory"
- [ 0.634658] 0x000000050000-0x000001000000 : "firmware"
- [ 0.648541] 2 uimage-fw partitions found on MTD device firmware
- [ 0.660322] Creating 2 MTD partitions on "firmware":
- [ 0.670184] 0x000000000000-0x0000001990d6 : "kernel"
- [ 0.680940] 0x0000001990d6-0x000000fb0000 : "rootfs"
- [ 0.691628] mtd: device 5 (rootfs) set to be root filesystem
- [ 0.704371] 1 squashfs-split partitions found on MTD device rootfs
- [ 0.716682] 0x000000390000-0x000000fb0000 : "rootfs_data"
- [ 0.729018] libphy: Fixed MDIO Bus: probed
- [ 0.747866] rt3050-esw 10110000.esw: link changed 0x00
- [ 0.759697] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
- [ 0.777943] NET: Registered protocol family 10
- [ 0.790947] Segment Routing with IPv6
- [ 0.798382] NET: Registered protocol family 17
- [ 0.807251] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
- [ 0.832924] 8021q: 802.1Q VLAN Support v1.8
- [ 0.850002] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
- [ 0.864928] Freeing unused kernel memory: 164K
- [ 0.873754] This architecture does not have kernel memory protection.
- [ 1.972449] init: Console is alive
- [ 1.979517] init: - watchdog -
- [ 2.455922] random: fast init done
- [ 3.224305] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 3.413656] usbcore: registered new interface driver usbfs
- [ 3.424685] usbcore: registered new interface driver hub
- [ 3.435338] usbcore: registered new device driver usb
- [ 3.451464] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 3.466331] ehci-platform: EHCI generic platform driver
- [ 3.487016] phy phy-10120000.usbphy.0: remote usb device wakeup disabled
- [ 3.500301] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz
- [ 3.510673] ehci-platform 101c0000.ehci: EHCI Host Controller
- [ 3.522128] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
- [ 3.537939] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
- [ 3.575954] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
- [ 3.589396] hub 1-0:1.0: USB hub found
- [ 3.597270] hub 1-0:1.0: 1 port detected
- [ 3.608647] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 3.622654] ohci-platform: OHCI generic platform driver
- [ 3.633347] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
- [ 3.646876] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
- [ 3.662660] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
- [ 3.740891] hub 2-0:1.0: USB hub found
- [ 3.748817] hub 2-0:1.0: 1 port detected
- [ 3.760723] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 3.785594] init: - preinit -
- [ 4.969527] rt3050-esw 10110000.esw: link changed 0x00
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3[ 5.154916] random: procd: uninitialized urandom read (4 bytes read)
- ] or [4] key and hit [enter] to select the debug level
- [ 8.372143] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
- [ 8.419322] urandom-seed: Seed file not found (/etc/urandom.seed)
- [ 8.470665] procd: - early -
- [ 8.476567] procd: - watchdog -
- [ 9.250220] procd: - watchdog -
- [ 9.256871] procd: - ubus -
- [ 9.399376] random: ubusd: uninitialized urandom read (4 bytes read)
- [ 9.451774] random: ubusd: uninitialized urandom read (4 bytes read)
- [ 9.465024] random: ubusd: uninitialized urandom read (4 bytes read)
- [ 9.478707] procd: - init -
- Please press Enter to activate this console.
- [ 9.902542] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 9.923231] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 9.944163] Loading modules backported from Linux version v4.19.32-0-g3a2156c839c7
- [ 9.959233] Backport generated by backports.git v4.19.32-1-0-g1c4f7569
- [ 9.975687] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 9.996491] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
- [ 10.076362] xt_time: kernel timezone is -0000
- [ 10.150025] mt76_wmac 10300000.wmac: ASIC revision: 76280001
- [ 11.178116] mt76_wmac 10300000.wmac: Firmware Version: 20151201
- [ 11.189926] mt76_wmac 10300000.wmac: Build Time: 20151201183641
- [ 11.215926] mt76_wmac 10300000.wmac: firmware init done
- [03060D0B][03050D0B]
- DDR Calibration DQS reg = 00008888
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement