settings.ini for IIIDMax PETG on ankermake m5

[base_param]
international_language=false
param_print_mode=normal
anker_param_ai_camera=false
camera_take_picture_time=30
anker_abc_1=[ ]
anker_abc_2=[ ]
camera_position="[288.78, 20.27, 9]"
camera_position_x=288.780
camera_position_y=20.27
camera_position_z=9
camera_up="[-0.5, 0, 0.87]"
camera_up_x=-0.50
camera_up_y=0
camera_up_z=0.87
camera_view_vector="[-0.87, 0, -0.5]"
camera_view_vector_x=-0.87
camera_view_vector_y=0
camera_view_vector_z=-0.50
camera_resolution=1920 × 1080
camera_resolution_w=1920
camera_resolution_h=1080
camera_field_view=60
ak_meshfix_dynamic_resolution=false
meshfix_maximum_resolution=0.30
meshfix_maximum_travel_resolution=0.313
meshfix_maximum_deviation=0.03
relative_extrusion=false
ak_VAJK_K_enabled=false
ak_K_print=0.06
ak_K_infill=0.06
ak_K_wall=0.06
ak_K_wall_0=0.06
ak_K_wall_x=0.06
ak_K_topbottom=0.06
ak_K_support=0.06
ak_K_skirt_brim=0.06
ak_K_layer_0=0.06
shrink_infill_shrink_distance=0
wall_ruler_concave_convex_enable=true
wall_ruler_concave_percent=20
wall_ruler_convex_percent=50
wall_ruler_separate_percent=20
small_hole_max_size=3
small_feature_max_length=9.42
small_feature_speed_factor=50
small_feature_speed_factor_0=50
wall_min_extrusion=0
wall_overhang_angle=45
wall_overhang_area_filter=0.80
wall_overhang_extend_circle=false
wall_overhang_extend_type=gradually_xy
overhang_min_line_length=5
wall_overhang_extend_xy_distance=0
wall_overhang_extend_z_distance=10
overhang_inner_wall_shrink_distance=0
overhang_related_inner_wall_slow_down=true
wall_overhang_speed_factor=30
wall_overhang_flow_factor=120
skin_overhang_enable=true
skin_overlap_overhang_speed=30
skin_overlap_overhang_flow=105
skin_overlap_overhang=120
skin_overlap_overhang_mm=0
optimize_wall_0_printing_order=true
optimize_wall_hole_printing=true
reverse_hole_outer_wall_print_orient=true
optimize_wall_small_printing=true
optimize_single_part_z_seam=0
show_machine_setting=false
machine_max_jerk_xy=30
machine_max_jerk_z=0.30
machine_max_jerk_e=3
bridge_settings_enabled=true
bridge_split_min_length=5
bridge_shrink_length=0.01
bridge_wall_min_length=5
bridge_skin_support_threshold=50
bridge_sparse_infill_max_density=0
bridge_wall_coast=100
bridge_wall_speed=50
bridge_wall_material_flow=100
bridge_skin_speed=50
bridge_skin_material_flow=100
bridge_skin_density=110
bridge_fan_speed=100
bridge_enable_more_layers=true
bridge_skin_speed_2=50
bridge_skin_material_flow_2=100
bridge_skin_density_2=75
bridge_fan_speed_2=0
bridge_skin_speed_3=50
bridge_skin_material_flow_3=110
bridge_skin_density_3=80
bridge_fan_speed_3=0
machine_index_name=AnkerMake M5
extruder_index_name=0.4 mm
material_index_name=PETG-alt
parameter_index_name=PETG-IIIDMax
extract_param_from_gcode=false
check_param_lost_interval=60
coasting_enable=false
coasting_volume=0.06
coasting_min_volume=0.80
coasting_speed=90
machine_name=AnkerMake M5
machine_show_variants=false
machine_start_gcode="; config start gcode "
machine_end_gcode="; config end gcode\nM104 S0\nM140 S0\n;Retract the filament\nG92 E1\nG1 E-1 F300\nG28 X0 Y0\nM84"
material_guid=
material_bed_temp_wait=true
material_print_temp_wait=true
material_print_temp_prepend=true
material_bed_temp_prepend=true
machine_width=235
machine_depth=235
machine_shape=rectangular
machine_buildplate_type=glass
machine_height=250
machine_heated_bed=true
machine_heated_build_volume=false
build_volume_temperature=0
machine_always_write_active_tool=false
machine_center_is_zero=false
machine_extruder_count=1
extruders_enabled_count=1
machine_nozzle_tip_outer_diameter=1
machine_nozzle_head_distance=3
machine_nozzle_expansion_angle=45
machine_heat_zone_length=16
machine_nozzle_temp_enabled=true
machine_nozzle_heat_up_speed=2
machine_nozzle_cool_down_speed=2
machine_min_cool_heat_time_window=50
machine_gcode_flavor=RepRap (Marlin/Sprinter)
machine_firmware_retract=false
machine_extruders_share_heater=false
machine_extruders_share_nozzle=false
machine_extruders_shared_nozzle_initial_retraction=0
machine_disallowed_areas=[]
machine_head_with_fans_polygon="[ [ -20, 10 ], [ 10, 10 ], [ 10, -10 ], [ -20, -10 ] ]"
gantry_height=250
machine_use_extruder_offset_to_offset_coords=true
extruder_prime_pos_abs=false
machine_max_feedrate_x=300
machine_max_feedrate_y=300
machine_max_feedrate_z=20
machine_max_feedrate_e=100
machine_max_acceleration_x=2500
machine_max_acceleration_y=2500
machine_max_acceleration_z=2500
machine_max_acceleration_e=2500
machine_acceleration=2500
machine_steps_per_mm_x=80
machine_steps_per_mm_y=80
machine_steps_per_mm_z=400
machine_steps_per_mm_e=1312
machine_endstop_positive_direction_x=false
machine_endstop_positive_direction_y=false
machine_endstop_positive_direction_z=true
machine_minimum_feedrate=0
machine_feeder_wheel_diameter=10
extruder_nr=0
machine_nozzle_id=unknown
machine_nozzle_size=0.40
machine_nozzle_offset_x=0
machine_nozzle_offset_y=0
machine_extruder_start_code=
machine_extruder_start_pos_abs=false
machine_extruder_start_pos_x=0
machine_extruder_start_pos_y=0
machine_extruder_end_code=
machine_extruder_end_pos_abs=false
machine_extruder_end_pos_x=0
machine_extruder_end_pos_y=0
extruder_prime_pos_z=0
machine_extruder_cooling_fan_number=0
nozzle_disallowed_areas=[]
layer_height=0.30
layer_height_0=0.24
line_width=0.40
wall_line_width=0.40
wall_line_width_0=0.42
thin_wall_line_width_0=0.10
wall_line_width_x=0.40
skin_line_width=0.40
infill_line_width=0.40
skirt_brim_line_width=0.40
support_line_width=0.40
support_interface_line_width=0.40
support_roof_line_width=0.40
support_bottom_line_width=0.40
prime_tower_line_width=0.40
initial_layer_line_width_factor=100
wall_extruder_nr=-1
wall_0_extruder_nr=-1
wall_x_extruder_nr=-1
wall_thickness=1.40
wall_line_count=3
wall_0_wipe_dist=0.20
wall_0_inset=0
optimize_wall_printing_order=true
outer_inset_first=false
alternate_extra_perimeter=true
travel_compensate_overlapping_walls_enabled=true
travel_compensate_overlapping_walls_0_enabled=true
travel_compensate_overlapping_walls_x_enabled=true
wall_min_flow=0
wall_min_flow_retract=false
fill_perimeter_gaps=everywhere
filter_out_tiny_gaps=true
fill_outline_gaps=false
xy_offset=0
xy_offset_layer_0=0
hole_xy_offset=0
z_seam_type=shortest
z_seam_position=back
z_seam_x=120
z_seam_y=130
z_seam_corner=z_seam_corner_weighted
z_seam_relative=false
z_seam_min_angle_diff=36
z_seam_max_angle=162
top_bottom_extruder_nr=-1
top_bottom_thickness=1.20
top_thickness=1.20
top_layers=4
bottom_thickness=1.20
bottom_layers=4
initial_bottom_layers=4
roofing_extruder_nr=-1
roofing_layer_count=0
top_bottom_pattern=concentric
top_bottom_pattern_0=concentric
connect_skin_polygons=false
skin_monotonic=true
skin_angles=[ ]
skin_no_small_gaps_heuristic=false
skin_outline_count=0
top_skin_density=100
top_surface_one_wall=false
ironing_enabled=false
ironing_only_highest_layer=false
ironing_pattern=zigzag
ironing_monotonic=false
ironing_line_spacing=0.10
ironing_flow=10
ironing_inset=0.39
speed_ironing=40
acceleration_ironing=500
jerk_ironing=10
skin_overlap=0
skin_overlap_mm=0
skin_preshrink=1.22
top_skin_preshrink=1.22
bottom_skin_preshrink=1.22
expand_skins_expand_distance=1.22
top_skin_expand_distance=1.22
bottom_skin_expand_distance=1.22
max_skin_angle_for_expansion=90
min_skin_width_for_expansion=0
infill_extruder_nr=-1
infill_sparse_density=20
infill_line_distance=6
infill_pattern=triangles
zig_zaggify_infill=true
connect_infill_polygons=false
infill_angles=[90]
infill_offset_x=0
infill_offset_y=0
infill_randomize_start_location=true
infill_multiplier=1
infill_wall_line_count=0
sub_div_rad_add=0.40
infill_overlap=10
infill_overlap_mm=0.04
infill_wipe_dist=0.10
infill_sparse_thickness=0.30
gradual_infill_steps=0
gradual_infill_step_height=2
infill_before_walls=true
min_infill_area=0
infill_support_enabled=false
infill_support_angle=40
skin_edge_support_thickness=0
skin_edge_support_layers=0
material_diameter=1.75
material_density=1.24
material_linear_density=2.98
default_material_print_temperature=210
material_print_temperature=230
before_homing_temperature=240
material_print_temperature_layer_0=240
material_initial_print_temperature=220
material_final_print_temperature=215
default_material_bed_temperature=60
material_bed_temperature=75
material_bed_temperature_layer_0=80
material_extrusion_cool_down_speed=0.70
material_adhesion_tendency=10
material_surface_energy=100
material_shrinkage_percentage=100
material_crystallinity=false
material_anti_ooze_retracted_position=-4
material_anti_ooze_retraction_speed=5
material_break_preparation_retracted_position=-16
material_break_preparation_speed=2
material_break_preparation_temperature=230
material_break_retracted_position=-50
material_break_speed=25
material_break_temperature=50
material_flush_purge_speed=0.50
material_flush_purge_length=60
material_end_of_filament_purge_speed=0.50
material_end_of_filament_purge_length=20
material_maximum_park_duration=300
material_no_load_move_factor=0.94
material_flow=105
wall_material_flow=105
wall_0_material_flow=105
wall_x_material_flow=105
skin_material_flow=105
roofing_material_flow=105
infill_material_flow=105
skirt_brim_material_flow=105
support_material_flow=105
support_interface_material_flow=105
support_roof_material_flow=105
support_bottom_material_flow=105
prime_tower_flow=105
material_flow_layer_0=120
material_standby_temperature=175
speed_travel=125
speed_print=120
speed_infill=120
speed_wall=72
speed_wall_0=72
speed_wall_x=120
speed_topbottom=60
speed_roofing=60
speed_support=120
speed_support_infill=120
speed_support_interface=80
speed_support_roof=80
speed_support_bottom=80
speed_prime_tower=120
speed_layer_0=120
speed_print_layer_0=120
speed_travel_layer_0=120
skirt_brim_speed=120
speed_z_hop=10
speed_slowdown_layers=2
speed_equalize_flow_enabled=false
speed_equalize_flow_max=72
acceleration_enabled=true
acceleration_travel=500
acceleration_print=500
acceleration_infill=500
acceleration_wall=500
acceleration_wall_0=500
acceleration_wall_x=500
acceleration_topbottom=500
acceleration_roofing=500
acceleration_support=500
acceleration_support_infill=500
acceleration_support_interface=500
acceleration_support_roof=500
acceleration_support_bottom=500
acceleration_prime_tower=500
acceleration_layer_0=500
acceleration_travel_layer_0=500
acceleration_print_layer_0=500
acceleration_skirt_brim=500
jerk_enabled=true
jerk_travel=10
jerk_print=10
jerk_infill=10
jerk_wall=10
jerk_wall_0=8
jerk_wall_x=10
jerk_topbottom=10
jerk_roofing=10
jerk_support=10
jerk_support_infill=10
jerk_support_interface=10
jerk_support_roof=10
jerk_support_bottom=10
jerk_prime_tower=10
jerk_layer_0=10
jerk_travel_layer_0=10
jerk_print_layer_0=10
jerk_skirt_brim=10
retraction_enable=true
retract_at_layer_change=false
retraction_amount=3
retraction_speed=30
retraction_retract_speed=30
retraction_prime_speed=30
retraction_extra_prime_amount=0
retraction_prime_min_travel=20
retraction_min_travel=0.80
retraction_count_max=90
retraction_extrusion_window=0.10
limit_support_retractions=false
retraction_combing=off
retraction_combing_max_distance=3
travel_retract_before_outer_wall=true
travel_avoid_other_parts=true
travel_avoid_supports=true
travel_avoid_distance=0.63
layer_start_x=0
layer_start_y=0
retraction_hop_enabled=false
retraction_hop_only_when_collides=false
retraction_hop=1
retraction_hop_after_extruder_switch=true
retraction_hop_after_extruder_switch_height=1
cool_fan_enabled=false
cool_fan_speed=0
cool_fan_speed_min=0
cool_fan_speed_max=0
cool_min_layer_time_fan_speed_max=10
cool_fan_speed_0=0
cool_fan_full_at_height=0.24
cool_fan_full_layer=2
cool_min_layer_time=6
cool_min_speed_includes_outer_walls=false
cool_min_speed=30
cool_lift_head=false
support_enable=false
support_extruder_nr=0
support_infill_extruder_nr=0
support_extruder_nr_layer_0=0
support_interface_extruder_nr=0
support_roof_extruder_nr=0
support_bottom_extruder_nr=0
support_structure=normal
support_tree_angle=40
support_tree_branch_distance=1
support_tree_branch_diameter=2
support_tree_branch_diameter_angle=5
support_tree_collision_resolution=0.20
support_type=everywhere
support_angle=60
support_pattern=zigzag
support_wall_count=0
zig_zaggify_support=false
support_connect_zigzags=true
support_infill_rate=30
support_line_distance=1.333
support_initial_layer_line_distance=1.333
support_infill_angles=[ ]
support_brim_enable=false
support_brim_width=8
support_brim_line_count=20
support_z_distance=0.10
support_top_distance=0.20
support_bottom_distance=0.40
support_xy_distance=0.80
support_xy_overrides_z=xy_overrides_z
support_xy_distance_overhang=0.20
support_bottom_stair_step_height=0.30
support_bottom_stair_step_width=5
support_bottom_stair_step_min_slope=10
support_join_distance=2
support_offset=2
support_infill_sparse_thickness=0.30
gradual_support_infill_steps=0
gradual_support_infill_step_height=1
minimum_support_area=5
support_interface_enable=false
support_roof_enable=false
support_bottom_enable=false
support_interface_height=2
support_roof_height=2
support_bottom_height=2
support_interface_skip_height=0.30
support_interface_density=50
support_roof_density=50
support_roof_line_distance=0.80
support_bottom_density=50
support_bottom_line_distance=0.80
support_interface_pattern=zigzag
support_roof_pattern=zigzag
support_bottom_pattern=zigzag
minimum_interface_area=1
minimum_roof_area=1
minimum_bottom_area=1
support_interface_offset=0
support_roof_offset=0
support_bottom_offset=0
support_interface_angles=[ ]
support_roof_angles=[ ]
support_bottom_angles=[ ]
support_fan_enable=false
support_supported_skin_fan_speed=100
support_use_towers=false
support_tower_diameter=3
support_tower_maximum_supported_diameter=3
support_tower_roof_angle=65
support_mesh_drop_down=true
support_meshes_present=false
prime_blob_enable=false
extruder_prime_pos_x=0
extruder_prime_pos_y=0
adhesion_type=none
adhesion_extruder_nr=0
skirt_line_count=1
skirt_gap=3
skirt_brim_minimal_length=250
brim_width=8
brim_line_count=20
brim_gap=0
brim_replaces_support=true
brim_outside_only=true
raft_margin=15
raft_smoothing=5
raft_airgap=0.30
layer_0_z_overlap=0.15
raft_surface_layers=2
raft_surface_thickness=0.30
raft_surface_line_width=0.40
raft_surface_line_spacing=0.40
raft_interface_thickness=0.450
raft_interface_line_width=0.80
raft_interface_line_spacing=1
raft_base_thickness=0.288
raft_base_line_width=0.80
raft_base_line_spacing=1.60
raft_speed=60
raft_surface_speed=60
raft_interface_speed=45
raft_base_speed=45
raft_acceleration=500
raft_surface_acceleration=500
raft_interface_acceleration=500
raft_base_acceleration=500
raft_jerk=10
raft_surface_jerk=10
raft_interface_jerk=10
raft_base_jerk=10
raft_fan_speed=0
raft_surface_fan_speed=0
raft_interface_fan_speed=0
raft_base_fan_speed=0
prime_tower_enable=false
prime_tower_size=20
prime_tower_min_volume=6
prime_tower_position_x=230.97
prime_tower_position_y=208.97
prime_tower_wipe_enabled=true
prime_tower_brim_enable=false
ooze_shield_enabled=false
ooze_shield_angle=60
ooze_shield_dist=2
switch_extruder_retraction_amount=16
switch_extruder_retraction_speeds=20
switch_extruder_retraction_speed=20
switch_extruder_prime_speed=20
switch_extruder_extra_prime_amount=0
meshfix_union_all=true
meshfix_union_all_remove_holes=false
meshfix_extensive_stitching=false
meshfix_keep_open_polygons=false
multiple_mesh_overlap=0.15
carve_multiple_volumes=false
alternate_carve_order=true
remove_empty_first_layers=true
print_sequence=all_at_once
infill_mesh=false
infill_mesh_order=0
cutting_mesh=false
mold_enabled=false
mold_width=5
mold_roof_height=0.50
mold_angle=40
support_mesh=false
anti_overhang_mesh=false
magic_mesh_surface_mode=normal
magic_spiralize=false
magic_spiralize_print_speed=30
smooth_spiralized_contours=true
slicing_tolerance=middle
roofing_line_width=0.40
roofing_pattern=concentric
roofing_monotonic=true
roofing_angles=[ ]
infill_enable_travel_optimization=false
material_flow_dependent_temperature=false
material_flow_temp_graph="[[3.5,200],[7.0,240]]"
minimum_polygon_circumference=1
support_skip_some_zags=false
support_skip_zag_per_mm=20
support_zag_skip_count=15
draft_shield_enabled=false
draft_shield_dist=10
draft_shield_height_limitation=full
draft_shield_height=10
conical_overhang_enabled=false
conical_overhang_angle=50
conical_overhang_hole_size=0
cross_infill_pocket_size=6
cross_infill_density_image=
cross_support_density_image=
support_conical_enabled=false
support_conical_angle=30
support_conical_min_width=5
magic_fuzzy_skin_enabled=false
magic_fuzzy_skin_outside_only=false
magic_fuzzy_skin_thickness=0.30
magic_fuzzy_skin_point_density=1.25
magic_fuzzy_skin_point_dist=0.80
flow_rate_max_extrusion_offset=0
flow_rate_extrusion_offset_factor=100
wireframe_enabled=false
wireframe_height=3
wireframe_roof_inset=3
wireframe_printspeed=5
wireframe_printspeed_bottom=5
wireframe_printspeed_up=5
wireframe_printspeed_down=5
wireframe_printspeed_flat=5
wireframe_flow=100
wireframe_flow_connection=100
wireframe_flow_flat=100
wireframe_top_delay=0
wireframe_bottom_delay=0
wireframe_flat_delay=0.10
wireframe_up_half_speed=0.30
wireframe_top_jump=0.60
wireframe_fall_down=0.50
wireframe_drag_along=0.60
wireframe_strategy=compensate
wireframe_straight_before_down=20
wireframe_roof_fall_down=2
wireframe_roof_drag_along=0.80
wireframe_roof_outer_delay=0.20
wireframe_nozzle_clearance=1
adaptive_layer_height_enabled=false
adaptive_layer_height_variation=0.10
adaptive_layer_height_variation_step=0.01
adaptive_layer_height_threshold=0.20
clean_between_layers=false
max_extrusion_before_wipe=10
wipe_retraction_enable=true
wipe_retraction_amount=3
wipe_retraction_extra_prime_amount=0
wipe_retraction_speed=30
wipe_retraction_retract_speed=30
wipe_retraction_prime_speed=30
wipe_pause=0
wipe_hop_enable=false
wipe_hop_amount=1
wipe_hop_speed=10
wipe_brush_pos_x=100
wipe_repeat_count=5
wipe_move_distance=20
center_object=false
mesh_position_x=0
mesh_position_y=0
mesh_position_z=0
mesh_rotation_matrix="[[1,0,0], [0,1,0], [0,0,1]]"
keep_wall0_speed_when_cooling=true
overhang_inner_wall_shrink=0.05
skin_related_wall_slow_down=true
ak_VAJK_J_E_enabled=false
ak_J_E_print=3
ak_J_E_infill=3
ak_J_E_wall=3
ak_J_E_wall_0=3
ak_J_E_wall_x=3
ak_J_E_topbottom=3
ak_J_E_support=3
ak_J_E_skirt_brim=3
ak_J_E_layer_0=3
anker_param_ai_uplayer_array=[ ]
anker_param_ai_height_array=[ ]
index_of_role_order_in_part=0
min_contact_area=25

[ak_meta]
meta_profile_name=PETG-IIIDMax
meta_profile_visible=true
meta_current_machine_name=AnkerMake M5
meta_modify_time_str=2023-06-25 10:44:02
meta_modify_time=@DateTime(\0\0\0\x10\0\0\0\0\0\0%\x89\xd9\x2M\xa1\x84\0)
meta_current_material_name=PETG-alt
meta_current_nozzle_name=0.4 mm