[2019-06-17 10:10:12] [Output] : ★ Alex Harold makes his way into the Subaru,opening the front left door.
[2019-06-17 10:10:13] [Output] : * Alex Harold presses on the key to unlock the vehicle. ((2019 Subaru WRX STI)) *
[2019-06-17 10:10:39] [Output] : ★ Alex Harold then pulls up the hood release cable located near the brake pedal poping up the hood.
[2019-06-17 10:11:09] [Output] : ★ With the hood in the rear now released Alex makes his way to the back of the car      ((Alex Harold))
[2019-06-17 10:11:11] [Output] : Vehicle spawn position set.
[2019-06-17 10:11:53] [Output] : ★ Alex Harold inserts his hands under the hood and searches for the release trigger.
[2019-06-17 10:12:19] [Output] : ★ Alex Harold pops the trigger and lifts the hood up,letting it sit on the hydraulic arms.
[2019-06-17 10:12:33] [Output] : ★ The fully engine of the car would now be exposed.      ((Alex Harold))
[2019-06-17 10:12:43] [Output] : ★ There would be a bunch of tools near the first car lift.      ((Alex Harold))
[2019-06-17 10:13:01] [Output] : ★ Alex Harold makes his way to the tools in order to pick up his impact gun and pliers.
[2019-06-17 10:13:31] [Output] : ★ Alex Harold leans over the tools and picks up the impact gun and his pliers,returning to the car's back
[2019-06-17 10:16:25] [Output] : ★ The intake would be sitting on the top of the engine with the four throtles attached.      ((Alex Harold))
[2019-06-17 10:16:55] [Output] : ★ There would also be four hoses attached to each throtle,heading into the two air filters.      ((Alex Harold))
[2019-06-17 10:19:08] [Output] : ★ Alex Harold grabs up his pliers and starts untightening the clamps holding the four hoses.
[2019-06-17 10:19:40] [Output] : ★ Alex Harold would then grab each hose's end and let it sit on top of the engine letting the throtles fre
[2019-06-17 10:19:42] [Output] : Alex Harold: (( free* ))
[2019-06-17 10:20:12] [Output] : ★ The two air filter of the engine would be installed on both sides on the rear fender's walls      ((Alex Harold))
[2019-06-17 10:20:42] [Output] : ★ Alex Harold uses his pliers again and disconnects the clamp holding the left hose from the left air...
[2019-06-17 10:20:48] [Output] : ★ Alex Harold ...filter.
[2019-06-17 10:21:01] [Output] : ★ Alex Harold then grabs the hose out and places it down on the ground.
[2019-06-17 10:21:20] [Output] : ★ Alex Harold would then use the pliers again and repeat the process to get the right hose out as well.
[2019-06-17 10:21:33] [Output] : ★ Alex Harold then drags out the hose and puts it on the ground near the other one.
[2019-06-17 10:22:03] [Output] : ★ The air filter's housings would each have four bolts tightening the top cap.      ((Alex Harold))
[2019-06-17 10:22:29] [Output] : ★ Alex Harold starts up the impact gun and makes his way to the left air filter in order to get it out
[2019-06-17 10:22:51] [Output] : ★ Alex Harold unbolts the four bolts holding the cap in and then pockets them up,holding the cap with his.
[2019-06-17 10:22:57] [Output] : ★ Alex Harold ...left hand
[2019-06-17 10:23:13] [Output] : ★ Alex Harold then takes the cap out and places it on the ground near the two hoses.
[2019-06-17 10:23:42] [Output] : ★ As the cap is dettached,the air filter would be exposed.      ((Alex Harold))
[2019-06-17 10:23:57] [Output] : ★ Alex Harold drags the old air filter out and throws it away on the ground.
[2019-06-17 10:24:22] [Output] : ★ The bottom cap of the air filter's housing would be held to the chasis with two clamps      ((Alex Harold))
[2019-06-17 10:24:56] [Output] : ★ Alex Harold grabs his pliers and unbolts the two claps holding the cap in.
[2019-06-17 10:25:21] [Output] : ★ Alex Harold then drags the cap out and places it on the ground.
[2019-06-17 10:25:35] [Output] : ★ Alex Harold would then start up the impact gun and make his way  to the right air filter.
[2019-06-17 10:25:54] [Output] : ★ Alex Harold disconnects the four bolts in a row and pockets them up,holding the cap with his left hand
[2019-06-17 10:26:18] [Output] : ★ Alex Harold then slides the cap out and positions it on the ground near the others.
[2019-06-17 10:26:41] [Output] : ★ Alex Harold would then pick up the old right air filter and drag it out,throwing it near the other one
[2019-06-17 10:27:19] [Output] : ★ Alex Harold then brings his pliers into the engine bay and uses it to disconnect the two clamps holding.
[2019-06-17 10:27:31] [Output] : ★ Alex Harold ...the bottom cap to the chassis
[2019-06-17 10:27:44] [Output] : ★ Alex Harold then grabs out the cap and throws it away on the ground near the other ones.
[2019-06-17 10:28:07] [Output] : ★ On each throtle body you could see a throtle position sensor cable leading into them.      ((Alex Harold))
[2019-06-17 10:28:33] [Output] : ★ Alex Harold uses his left hand and then pulls out each wire letting the throtles dettached.
[2019-06-17 10:29:50] [Output] : ★ Each throtle would be attached to the air intake housings with four bolts.      ((Alex Harold))
[2019-06-17 10:30:10] [Output] : ★ Alex Harold starts the impact gun up and heads to the first left throtle body.
[2019-06-17 10:30:26] [Output] : ★ Alex Harold then dettaches each bolt and holds the throtle with his left hand.
[2019-06-17 10:30:57] [Output] : ★ Alex Harold would then pocket up the four bolts and drag the throttle body out,repeating the process...
[2019-06-17 10:31:04] [Output] : ★ Alex Harold ...for all the other three.
[2019-06-17 10:31:26] [Output] : ★ Alex Harold then drags them all out and places them in a safe place near the suv on the left.
[2019-06-17 10:31:44] [Output] : ★ Alex Harold returns to the car then in order to proceed further
[2019-06-17 10:33:31] [Output] : ★ Under the air intake,there would be the two fuel rails leading the fuel into the engine.      ((Alex Harold))
[2019-06-17 10:33:48] [Output] :  [English] Alex Harold says: Right,so I have to get the rails out to dettach the intake...
[2019-06-17 10:34:10] [Output] : ★ Alex Harold inspects the fuel rails to check for any bolts holding them in.
[2019-06-17 10:34:59] [Output] : ★ There would be two bolts at the end of each fuel line holding them in.      ((Alex Harold))
[2019-06-17 10:35:14] [Output] : ★ Alex Harold starts up the impact gun and proceeds to dettach the first fuel line bolts out.
[2019-06-17 10:35:40] [Output] : ★ Alex Harold dettaches the first bolt and then pockets it heading to the rear one.
[2019-06-17 10:36:02] [Output] : ★ The rear bolt would also hold in place the fuel line leading into the fuel rail.      ((Alex Harold))
[2019-06-17 10:36:17] [Output] : ★ Alex Harold dettaches the bolts easily and then pockets it leaving the fuel line free.
[2019-06-17 10:36:33] [Output] : ★ Alex Harold then drags the fuel rail up and places it on the ground near the rest of parts.
[2019-06-17 10:36:48] [Output] : ★ The six injectors on the left side would now be exposed.      ((Alex Harold))
[2019-06-17 10:37:05] [Output] : ★ In order to dettach the intake manifold,Alex would have to get each injector out.      ((Alex Harold))
[2019-06-17 10:37:35] [Output] : ★ Alex Harold makes his way to the first injector and twists it to the left
[2019-06-17 10:38:00] [Output] : ★ A click would be heard and the injector would pop up by a few centimeters.      ((Alex Harold))
[2019-06-17 10:38:43] [Output] : ★ Alex Harold then repeats the process for each of the remaining five injectors,twisting them to the left.
[2019-06-17 10:38:47] [Output] : ★ Alex Harold ...to pop
[2019-06-17 10:39:46] [Output] : ★ Alex Harold then removes each injector from it's place and places them carefully on a safe place near...
[2019-06-17 10:39:48] [Output] : ★ Alex Harold ...the suv
[2019-06-17 10:40:01] [Output] : ★ Alex Harold then heads back to the right fuel rail in order to take it out.
[2019-06-17 10:40:24] [Output] : ★ Alex Harold starts up the impact gun and dettaches the front bolt of the fuel rail.
[2019-06-17 10:40:37] [Output] : ★ Alex Harold then pockets the bolt and mooves to the rear bolt.
[2019-06-17 10:40:48] [Output] : ★ Again,the rear bolt would also hold the fuel line in place.      ((Alex Harold))
[2019-06-17 10:41:07] [Output] : ★ Alex Harold carefully disconnects the rear bolt and lets the fuel line free on the engine bay.
[2019-06-17 10:41:21] [Output] : ★ You would notice a gasoline smell and some drips comming out of the two fuel lines.      ((Alex Harold))
[2019-06-17 10:41:56] [Output] : ★ Alex Harold pulls the fuel rail up after and gets it out of the engine bay,placing it near the other one
[2019-06-17 10:42:29] [Output] : ★ Alex Harold then twists all the injectors to the right in order to click them out of their place
[2019-06-17 10:43:00] [Output] : ★ After six clicks,each injector would be poped out of it's place.      ((Alex Harold))
[2019-06-17 10:43:38] [Output] : ★ Alex Harold then picks up the six fuel injectors and carefully places them on the floor near the others
[2019-06-17 10:43:54] [Output] : ★ In order to further dettach the rest of the parts,the engine cover would have to come out.      ((Alex Harold))
[2019-06-17 10:44:49] [Output] : ★ The engine cover would have eight bolts in total holding it over the rear shocks.      ((Alex Harold))
[2019-06-17 10:45:06] [Output] : ★ Alex Harold starts up the impact gun and dettaches all of the eight bolts in a row.
[2019-06-17 10:45:21] [Output] : ★ Alex Harold then places the bolts in his rear pocket and mooves further to remove the cover
[2019-06-17 10:45:40] [Output] : ★ As the engine cover is made out of carbon it is light enough to make Alex able to pick it      ((Alex Harold))
[2019-06-17 10:45:59] [Output] : ★ Alex Harold places his hands on each side of the engine cover and drags it out of place.
[2019-06-17 10:46:15] [Output] : ★ Alex Harold then heads to the bunch of tools in order to let the cover sit in a safe place
[2019-06-17 10:46:39] [Output] : ★ Alex Harold places the engine cover down and then mooves back to the car
[2019-06-17 10:47:32] [Output] : ★ The air intake would now have twenty four bolts holding it to the engine block.      ((Alex Harold))
[2019-06-17 10:47:53] [Output] : ★ Alex Harold uses his wrench and starts dettaching the twelve bolts on the left side
[2019-06-17 10:48:06] [Output] : ★ Alex Harold then removes the bolts and carefully pockets them up
[2019-06-17 10:48:50] [Output] : ★ Alex Harold then makes his way to the right side of the manifold starting to remove the rest of twelve..
[2019-06-17 10:48:53] [Output] : ★ Alex Harold ...bolts
[2019-06-17 10:49:03] [Output] : ★ Alex Harold then pockets them up as well making the intake sit free.
[2019-06-17 10:49:28] [Output] : ★ Alex Harold places his both hands on the sides of the manifold and lifts it out of place.
[2019-06-17 10:49:40] [Output] : ★ Alex Harold then makes his way back near the engine cover
[2019-06-17 10:50:08] [Output] : ★ Alex Harold leaves the intake manifold seat near the engine cover in order to store it in a safe place.
[2019-06-17 10:50:29] [Output] : ★ Alex Harold then returns up to the car's engine to further dettach the parts.
[2019-06-17 10:51:32] [Output] : ★ The twelve ignition coils placed on both sides of the engine would all have a wire leading      ((Alex Harold))
[2019-06-17 10:51:34] [Output] : ★ Alex Harold ...into them
[2019-06-17 10:51:55] [Output] : ★ Alex Harold makes his way to the right side of the engine and starts pulling out the wires of the coils.
[2019-06-17 10:51:59] [Output] : ★ Alex Harold ...one by one
[2019-06-17 10:52:23] [Output] : ★ As the ignition coils on the right side are let free,Alex proceeds to the left side      ((Alex Harold))
[2019-06-17 10:52:48] [Output] : ★ Alex Harold then disconnects the six wires leading into the left side ignition coils and let them free..
[2019-06-17 10:52:52] [Output] : ★ Alex Harold ...as well
[2019-06-17 10:53:28] [Output] : ★ With the ignition coils now set free,Alex is able to further remove them and the sparks      ((Alex Harold))
[2019-06-17 10:53:52] [Output] : ★ Alex Harold twists each coil on the left side to the left until they all click
[2019-06-17 10:54:04] [Output] : ★ After six clicks,all the ignition coils would be set free.      ((Alex Harold))
[2019-06-17 10:54:21] [Output] : ★ Alex Harold then drags them all six out and opens up his backpack,placing them into it.
[2019-06-17 10:55:04] [Output] : ★ Alex Harold then makes his way to the right side of the engine in order to remove the remaining six coil
[2019-06-17 10:55:07] [Output] : Alex Harold: (( coils* ))
[2019-06-17 10:55:23] [Output] : ★ Alex Harold twists them each to the right in order to click them out of the spark plugs
[2019-06-17 10:55:51] [Output] : ★ Alex Harold then picks up all of the six and puts them near the rest in the backpack.
[2019-06-17 10:59:07] [Output] : ★ Alex Harold would then go back to the bunch of tools in order to pick up a spark plugs key
[2019-06-17 10:59:39] [Output] : ★ Alex Harold leans over to the ground and picks up the key desired to unbolt the spark plugs.
[2019-06-17 10:59:50] [Output] : ★ Alex Harold then returns to the car's engine holding the key with his right hand
[2019-06-17 11:00:19] [Output] : ★ There would be a total of twelve spark plugs firing up the engine.      ((Alex Harold))
[2019-06-17 11:04:19] [Output] : ★ Alex Harold places the key on top of the firts spark plug and starts twisting it to the left.t
[2019-06-17 11:04:37] [Output] : ★ As the key is rotated,the spark plug remains in the key      ((Alex Harold))
[2019-06-17 11:05:09] [Output] : ★ Alex Harold takes the spark plug out and places it in his backpack,reapeating the same process for the..
[2019-06-17 11:05:19] [Output] : ★ Alex Harold ...rest of eleven remaining spark plugs.
[2019-06-17 11:05:28] [Output] : ★ Alex Harold then places his key on the ground.
[2019-06-17 22:38:40] [Output] : ★ There would be a metal cover on the front side of the engine covering the alternator and...      ((Alex Harold))
[2019-06-17 22:38:48] [Output] : ★ Alex Harold ...the serpentine belts
[2019-06-17 22:39:07] [Output] : ★ In order to remove them,the rear bumper would have to be taken of.      ((Alex Harold))
[2019-06-17 22:39:21] [Output] : ★ Alex Harold searches the bumper for any bolts or clamps holding it to the chassis.
[2019-06-17 22:39:51] [Output] : ★ The bumper would be held in place by twelve clamps which click out.      ((Alex Harold))
[2019-06-17 22:40:08] [Output] : ★ Alex Harold starts dragging the rear bumper from the left side heading to the right.
[2019-06-17 22:40:27] [Output] : ★ After aplying medium force,the bumper would come off easily not breaking or damaging      ((Alex Harold))
[2019-06-17 22:40:58] [Output] : ★ Alex Harold heads to the engine cover with the rear bumper in his both hands
[2019-06-17 22:41:18] [Output] : ★ Alex Harold places the bumper down carefully not to scratch it.
[2019-06-17 22:41:30] [Output] : ★ Alex Harold would then head back to the engine to take of the rest
[2019-06-17 22:41:57] [Output] : ★ Alex Harold sits down on his knees and watches the bolts holding the metal cover over the timing...
[2019-06-17 22:42:01] [Output] : ★ Alex Harold ...components
[2019-06-17 22:43:01] [Output] : ★ There would be a total of eight bolts holding the cover on the timing parts.      ((Alex Harold))
[2019-06-17 22:43:25] [Output] : ★ The impact gun would be sitting on the floor near the car due to the last performed operatio      ((Alex Harold))
[2019-06-17 22:43:29] [Output] : Alex Harold: (( operations* ))
[2019-06-17 22:43:46] [Output] : ★ Alex Harold extends his left arm to the tool and picks it up returning to the engine.
[2019-06-17 22:44:23] [Output] : ★ Alex Harold starts up the impact gun and heads to the cover of the alternator.
[2019-06-17 22:44:41] [Output] : ★ There would be two bolts holding the alternator cover to the main timing cover      ((Alex Harold))
[2019-06-17 22:45:05] [Output] : ★ Alex Harold disconnects the two bolts holding the cover with his left arm.
[2019-06-17 22:45:21] [Output] : ★ Alex Harold would then pocket up the bolts and slide the cover out placing it on the ground
[2019-06-17 22:46:07] [Output] : ★ There would be another two bolts holding the power steering cover and a hose leading into it      ((Alex Harold))
[2019-06-17 22:46:35] [Output] : ★ Alex Harold picks up the pliers also located on the floor and bends up the clamps holding the hose in.
[2019-06-17 22:46:57] [Output] : ★ Alex Harold then picks up the hose and places it around the rear frame not to damage it when removing...
[2019-06-17 22:47:00] [Output] : ★ Alex Harold ...the engine
[2019-06-17 22:47:46] [Output] : ★ Alex Harold then starts up the impact gun and  removes the two bolts holding the power steering cover in
[2019-06-17 22:47:55] [Output] : ★ Alex Harold ..holding it with his left hand after.
[2019-06-17 22:48:09] [Output] : ★ Alex Harold then pockets up the two bolts and slides the cover out placing it near the other one.
[2019-06-17 22:48:25] [Output] : ★ With the two small covers exposed,the serpentine belts would be clearly visible.      ((Alex Harold))
[2019-06-17 22:49:34] [Output] : ★ Alex Harold starts up the impact gun again and makes his way to each of the eight bolts,one by one...
[2019-06-17 22:49:48] [Output] : ★ Alex Harold ...dettaching them all out and holding the main cover with his left arm.
[2019-06-17 22:50:38] [Output] : ★ Alex Harold then slides out the cover with the bolts staying in their holes and places it near the other
[2019-06-17 22:50:41] [Output] : ★ Alex Harold ...two covers
[2019-06-17 22:51:31] [Output] : ★ The rollers,belts and the AC compressor along with it's hose and sensor would now be visible      ((Alex Harold))
[2019-06-17 22:51:57] [Output] : ★ Alex Harold picks up the AC compressor's wire and drags it out from it's plae.
[2019-06-17 22:51:59] [Output] : Alex Harold: (( place* ))
[2019-06-17 22:52:25] [Output] : ★ Alex Harold then takes it and twists it around the rear right fender not to damage it when removing....
[2019-06-17 22:52:30] [Output] : ★ Alex Harold ...the rest of parts.
[2019-06-17 22:52:55] [Output] : ★ Alex Harold uses the impact gun again and dettaches the bolt holding the alternator's roller in.
[2019-06-17 22:53:09] [Output] : ★ Alex Harold then slides out the roller with it's bolt and places it on the right side of the car.
[2019-06-17 22:53:45] [Output] : ★ The alternator would be held in place by two bolts going into the engine block      ((Alex Harold))
[2019-06-17 22:54:38] [Output] : ★ Alex Harold drags the serpentine belt from the radiator and mooves it away not to cut it.
[2019-06-17 22:56:52] [Output] : ★ Alex Harold then starts up the impact gun and removes the two bolts holding in the alternator,holding it
[2019-06-17 22:57:19] [Output] : ★ Alex Harold then slides the alternator out of it's place with the bolts and places it on the right side
[2019-06-17 22:57:47] [Output] : ★ Alex Harold then picks up his wrench in order to dettach the metal hose leading inside the AC compressor
[2019-06-17 22:58:06] [Output] : ★ Alex Harold locks the wrench on the washer and twists it to the left a few times dettaching it.
[2019-06-17 22:58:33] [Output] : ★ Alex Harold then slides the line out of place and drags it to the rear right fender.
[2019-06-17 23:00:01] [Output] : ★ Alex Harold starts up the impact gun after and dettaches the bolts holding the AC compressor as well
[2019-06-17 23:00:11] [Output] : ★ Alex Harold the slides out the compressor and places it near the alternator.
[2019-06-17 23:00:47] [Output] : ★ The power steering line sitting on the right leading into the pump would have a washer...      ((Alex Harold))
[2019-06-17 23:01:58] [Output] : ★ Alex Harold uses his wrench again to twist the washer to the left a few times.
[2019-06-17 23:02:14] [Output] : ★ Alex Harold then grabs the line out and slides it to the left fender under the exhaust manifold
[2019-06-17 23:03:19] [Output] : ★ Alex Harold then places his hands on the serpentine belt only sitting on the idle rollers.
[2019-06-17 23:03:33] [Output] : ★ Alex Harold then drags it backwards a bit and then lifts it up removing it from the engine
[2019-06-17 23:03:59] [Output] : ★ Alex Harold bends the belt in half and places it near the alternator and compressor.
[2019-06-17 23:04:13] [Output] : ★ The power steering pump would be held in place by two bolts.      ((Alex Harold))
[2019-06-17 23:05:09] [Output] : ★ Alex Harold starts up the impact gun and makes his way to each of the bolts dettaching them both
[2019-06-17 23:05:39] [Output] : ★ Alex Harold then slides out the pump with it's bolts still in place and then puts it near the alternator
[2019-06-17 23:05:55] [Output] : ★ Alex Harold would then think of the next part needing to be taken out
[2019-06-17 23:07:32] [Output] : ★ Alex Harold stands up to the top of the engine looking for any wires that need to be taken of.
[2019-06-17 23:08:02] [Output] : ★ Alex Harold would spot a few sensor wires and takes them all out,placing then on the rear fenders
[2019-06-17 23:08:06] [Output] :  [English] Alex Harold says: Good,wires out...
[2019-06-17 23:08:14] [Output] :  [English] Alex Harold says: I have to take off the water pump,damn it
[2019-06-17 23:08:26] [Output] : ★ Alex Harold sits down again and makes his way to the middle of the idle rollers.
[2019-06-17 23:08:43] [Output] : ★ Sitting in the middle,there would be the watter pump that is held in by two side bolts      ((Alex Harold))
[2019-06-17 23:09:26] [Output] : ★ Alex Harold starts up the impact gun and then removes the two bolts holding the pump in the engine.
[2019-06-17 23:09:41] [Output] : ★ Alex Harold then slides out the pump and places it near the other timing parts.
[2019-06-17 23:12:19] [Output] : ★ The alternator crankshaft pulley would also be held in place by a big middle bolts.      ((Alex Harold))
[2019-06-17 23:12:41] [Output] : ★ Alex Harold starts up the impact gun again and makes his way to the bolt holding the pulley on the...
[2019-06-17 23:12:44] [Output] : ★ Alex Harold ...crankshaft
[2019-06-17 23:13:01] [Output] : ★ Alex Harold then slides the pulley out and places it on the ground near the rest of parts.
[2019-06-17 23:13:38] [Output] : ★ Alex Harold stands up and searches for the second elevator remote in his left pocket
[2019-06-17 23:13:56] [Output] : ★ Alex Harold then drags the remote out and uses the top button to raise up the car lift.
[2019-06-17 23:14:57] [Output] : ★ With the elevator raised up all the way,the exhaust system would be viewable from under...      ((Alex Harold))
[2019-06-17 23:14:59] [Output] : ★ Alex Harold ...the car
[2019-06-17 23:16:13] [Output] : ★ Alex Harold inspects the mufflers and exhaust manifolds for the bolts holding them
[2019-06-17 23:16:46] [Output] : ★ There would be two bolts holding each muffler to the manifolds and twelve bolts holding...      ((Alex Harold))
[2019-06-17 23:16:56] [Output] : ★ Alex Harold ...each exhaust manifold to the engine block.
[2019-06-17 23:17:12] [Output] : ★ Alex Harold starts up the impact gun and makes his way to the right muffler
[2019-06-17 23:17:33] [Output] : ★ Alex Harold places his left hand on the muffler and starts dettaching the bolts with his impact gun
[2019-06-17 23:17:44] [Output] : ★ Alex Harold then pockets up the bolts and places his both hands on the muffler.
[2019-06-17 23:17:57] [Output] : ★ Alex Harold slowly lowers the muffler down after and puts it on the ground.
[2019-06-17 23:18:08] [Output] : ★ Alex Harold then stands up again and makes his way to the left muffler.
[2019-06-17 23:18:42] [Output] : ★ Alex Harold holds the muffler with his left hand and starts dettaching the two bolts holding it
[2019-06-17 23:18:56] [Output] : ★ Alex Harold then pockets the bolts and place his both hands on the muffler.
[2019-06-17 23:19:12] [Output] : ★ Alex Harold drags it backwards a little and slowly brings it down,placing it near the other one
[2019-06-17 23:19:34] [Output] : ★ With the mufflers now removed,there would only be the two side exhaust manifolds held in by.      ((Alex Harold))
[2019-06-17 23:19:45] [Output] : ★ Alex Harold ...twenty four total bolts
[2019-06-17 23:20:07] [Output] : ★ Alex Harold heads to the left manifold in order to dettach the bolts.
[2019-06-17 23:20:33] [Output] : ★ Alex Harold starts up the impact gun and dettaches all the twelve bolts,one by one holding the pipes...
[2019-06-17 23:20:41] [Output] : ★ Alex Harold ...at the same time with the left hand
[2019-06-17 23:20:59] [Output] : ★ Alex Harold then pockets the bolts and places his both hands on the exhaust manifold
[2019-06-17 23:22:31] [Output] : ★ Alex Harold then lowers it down from the engine bay and holds it in his hands
[2019-06-17 23:22:49] [Output] : ★ Alex Harold heads to the mufflers and places the manifold near them as well.
[2019-06-17 23:23:03] [Output] : ★ Alex Harold then returns to the right exhaust manifold in order to dettach it
[2019-06-17 23:24:02] [Output] : ★ Alex Harold starts up the impact gun one more time and holds the manifold with his left hand
[2019-06-17 23:24:47] [Output] : ★ Alex Harold then dettaches all the twelve bolts,one by one and places them in his pocket
[2019-06-17 23:25:03] [Output] : ★ Alex Harold then puts his both hands on the manifold and slides it out of place,lowering it.
[2019-06-17 23:25:22] [Output] : ★ Alex Harold then makes his way to the rest of pipes to let the second manifold down.
[2019-06-17 23:25:51] [Output] : ★ Alex Harold puts down the second manifold and then makes his way to the engine
[2019-06-17 23:26:12] [Output] : ★ The last part on the bottom that needs to be taken out would be the oilpan.      ((Alex Harold))
[2019-06-17 23:26:37] [Output] : ★ The pan would be held in place by four bolts on each corner of the engine      ((Alex Harold))
[2019-06-17 23:26:54] [Output] : ★ Alex Harold makes his way to the main office to search for an empty pan
[2019-06-17 23:27:21] [Output] : ★ Alex Harold searches under the desk and takes out and empty ten liters pan
[2019-06-17 23:27:32] [Output] : ★ Alex Harold then takes it in his hand and makes his way to the car
[2019-06-17 23:28:11] [Output] : ★ Alex Harold places the pan on the ground under the oil pan middle bolt to drain the oild in it.
[2019-06-17 23:28:46] [Output] : ★ Alex Harold uses his wrench and dettaches the oil pan's with his left hand.
[2019-06-17 23:29:12] [Output] : ★ The oil filter of the car would be attached to the cover placed over the belts.      ((Alex Harold))
[2019-06-17 23:29:53] [Output] : ★ As the bolt is dettached,the old oil drains out of the engine straight into the pan.      ((Alex Harold))
[2019-06-17 23:30:14] [Output] : ★ After two minutes,all the oil would be now drained out.      ((Alex Harold))
[2019-06-17 23:30:30] [Output] : ★ Alex Harold picks up the full pan and makes his way to the stairs.
[2019-06-17 23:30:48] [Output] : ★ Alex Harold lets the pan down at the bottom of the stairs and returns to the engine
[2019-06-17 23:31:50] [Output] : ★ Alex Harold starts up the impact gun again and heads to the bolts holding the pan.
[2019-06-17 23:32:11] [Output] : ★ Alex Harold then places his hand on the pan holding it not to fall.
[2019-06-17 23:32:34] [Output] : ★ Alex Harold then removes the four bolts and pockets them up,placing his right hand on the pan as well
[2019-06-17 23:32:52] [Output] : ★ Alex Harold then slowly drags the pan down and places it on the left side of the car
[2019-06-17 23:33:26] [Output] : ★ Alex Harold then pushes down the bottom button of the remote and lowers down the car lift.
[2019-06-17 23:33:29] [Output] : * Alex Harold presses the button on the ramp controls lowering the car lift. *
[2019-06-17 23:33:55] [Output] : ★ Alex Harold looks into the engine bay and looks for the engine mounts holding the block in the chassis.
[2019-06-17 23:34:43] [Output] : ★ On the left side of the Subaruru,near the Suv would be a pack of four straps.      ((Alex Harold))
[2019-06-17 23:35:34] [Output] : ★ Alex Harold makes his way to the straps set and drags out three of them
[2019-06-17 23:35:48] [Output] : ★ Alex Harold then returns to the engine in order to tie it.
[2019-06-17 23:36:42] [Output] : ★ Alex Harold places the straps on the top of the engine and only holds one of them
[2019-06-17 23:39:06] [Output] : ★ Alex Harold unties the strap and lets it down on the right side of the car.
[2019-06-17 23:41:12] [Output] : ★ Alex Harold then throws the head of the belt around the left side and lets it fall down.
[2019-06-17 23:41:27] [Output] : ★ Alex Harold then picks up the second strap and reapeats the process.
[2019-06-17 23:41:42] [Output] : ★ Alex Harold goes under the car after and ties down the two straps.
[2019-06-17 23:41:53] [Output] : ★ Alex Harold would then go back up and pick the third strap.
[2019-06-17 23:43:05] [Output] : ★ Alex Harold ties the strap around the other two and tightens it up.
2019-06-17 19:42:07] [Output] : ★ Alex Harold searches for his remote in his left pocket
2019-06-17 19:42:26] [Output] : ★ Alex Harold then picks the remote and uses the top button to raise the lift up
2019-06-17 19:43:25] [Output] : ★ Alex Harold makes his way under the car in order to inspect how the transmision is attached
2019-06-17 19:45:46] [Output] : ★ As the car is rear wheel drive,the first parts to come off are the axles.      ((Alex Harold))
2019-06-17 19:46:57] [Output] : ★ Alex Harold extends his arm to the right side of the lift where the impact gun would be left.
2019-06-17 19:47:11] [Output] : ★ Alex Harold then picks up the impact gun and makes his way to the right wheel.
2019-06-17 19:48:13] [Output] : ★ Alex Harold starts up the impact gun and disconnects all the five lugnuts in a row.
2019-06-17 19:48:29] [Output] : ★ Alex Harold then places the lugnuts on the floor and slides the wheel out,placing it near the lugnuts
2019-06-17 19:50:24] [Output] : ★ The rear knuckle with the axle placed it the middle of it would now be exposed.      ((Alex Harold))
2019-06-17 19:50:51] [Output] : ★ As the axles lead into the axle shaft,they will need to be dettached with the hammer      ((Alex Harold))
2019-06-17 19:51:07] [Output] : ★ Alex Harold makes his way to the first lift where the bunch of tools would be.
2019-06-17 19:51:29] [Output] : ★ Alex Harold picks up a medium sized hammer and returns to the wheel's hub
2019-06-17 19:52:09] [Output] : ★ Missing the dustcap,the axle would only have the lock pin holding it.      ((Alex Harold))
2019-06-17 19:52:27] [Output] : ★ Alex Harold uses his hammer and hits the pin,getting it flying off
2019-06-17 19:52:50] [Output] : ★ Alex Harold then applies medium pressure on the hammer and hits the head of the axle a few times.
2019-06-17 19:53:01] [Output] : ★ As the axle is hit,it would come off the knuckle.      ((Alex Harold))
2019-06-17 19:53:21] [Output] : ★ Alex Harold goes under the car after and locates the axle.
2019-06-17 19:53:38] [Output] : ★ Alex Harold drags the head of the axle out of the hub and places it on the ramp.
2019-06-17 19:54:00] [Output] : ★ Alex Harold would then put his hands on the head leading into the axle shaft and slide the axle out.
2019-06-17 19:54:42] [Output] : ★ Alex Harold then gets the axle out and carefully places it on the floor in a safe place.
2019-06-17 19:55:01] [Output] : ★ Alex Harold would then get both,the impact gun and the hammer and make his way to the opposite wheel
2019-06-17 19:56:13] [Output] : ★ Alex Harold starts up the impact gun then and dettaches all the five lugnuts in a row,placing them on...
2019-06-17 19:56:16] [Output] : ★ Alex Harold the floor.
2019-06-17 19:56:27] [Output] : ★ Alex Harold slides the wheel out after and puts it near the lugnuts.
2019-06-17 19:56:43] [Output] : ★ Alex Harold lets the impact gun down on the ramp after and picks up the hammer in his right hand
2019-06-17 19:56:51] [Output] : ★ Alex Harold starts hitting up the pin until it goes out.
2019-06-17 19:57:11] [Output] : ★ As the pin flyes out,the axle would be ready to be hited      ((Alex Harold))
2019-06-17 19:57:33] [Output] : ★ Alex Harold starts hitting the axle in the middle,aplying medium pressure.
2019-06-17 19:57:47] [Output] : ★ After a few hits,the axle would be dettached completely from the knuckle      ((Alex Harold))
2019-06-17 19:57:55] [Output] : ★ Alex Harold goes under the car after and locates the left axle.
2019-06-17 19:58:32] [Output] : ★ Alex Harold pulls out the head of the axle from the knuckle and then slides it out from the shaft.
2019-06-17 19:58:51] [Output] : ★ Alex Harold carefully places down the axle after,on the floor near the other one.
2019-06-17 19:59:32] [Output] : ★ As the axles are now out,the transmision would be free to dettach.      ((Alex Harold))
2019-06-17 19:59:48] [Output] : ★ Alex Harold makes his way to the bunch of tools in order to pick up a ratchet.
2019-06-17 20:00:09] [Output] : ★ Alex Harold lets the hammer down and picks up a ratchet and two medium and long extensions
2019-06-17 20:00:49] [Output] : ★ Alex Harold keeps the ratchet in his right hand and makes his way to the other corner of the garage
2019-06-17 20:01:09] [Output] : ★ The wooden pallet would be located where Alex headed.      ((Alex Harold))
2019-06-17 20:01:27] [Output] : ★ Alex Harold puts his left hand under the pallet and starts pulling it to the car.
2019-06-17 20:01:50] [Output] : * Alex Harold would get the gun out holding it with his right hand *
2019-06-17 20:02:25] [Output] : ★ Alex Harold positions the wooden pallet under the transmision in order to lift it up.
2019-06-17 20:02:41] [Output] : ★ Alex Harold then goes under the car in order to get the starter out.
2019-06-17 20:03:20] [Output] : ★ Alex Harold attaches the medium size extension to his ratchet and positions the ratchet on the bottom...
2019-06-17 20:03:22] [Output] : ★ Alex Harold ...bolt
2019-06-17 20:03:34] [Output] : ★ Alex Harold then spots the alternator wire leading into the back of it.
2019-06-17 20:03:55] [Output] : ★ Alex Harold uses his left hand and pulls out the wire,leting it hang on the ramp.
2019-06-17 20:04:55] [Output] : ★ Alex Harold then twists the ratchet to the left dettaching the first bottom bolt of the alternator.
2019-06-17 20:05:15] [Output] : ★ Alex Harold then places the bolt down and heads to the right bolt of the starter
2019-06-17 20:06:37] [Output] : ★ Alex Harold twists the ratchet to the left and slides out the second bolt holding the starter in.
2019-06-17 20:06:57] [Output] : ★ Alex Harold puts the ratchet down after and disconnects the medium sized extension
2019-06-17 20:07:10] [Output] : ★ Alex Harold would then attach the long extension to it and head to the top bolt.
2019-06-17 20:07:35] [Output] : ★ Alex Harold slides the extension's head to the top bolt of the starter and starts twisting his ratchet..
2019-06-17 20:07:39] [Output] : ★ Alex Harold ...to the left
2019-06-17 20:08:28] [Output] : ★ Alex Harold then puts the ratchet on the ground and places his hands on the starter.
2019-06-17 20:08:39] [Output] : ★ Alex Harold give the starter a good shake pulling it out from it's place.
2019-06-17 20:08:59] [Output] : ★ Alex Harold then puts the starter to sit near the axles.
2019-06-17 20:09:28] [Output] : ★ Two wires leading into the transmision would be spotted by Alex when removing the starter.      ((Alex Harold))
2019-06-17 20:10:12] [Output] : ★ Alex Harold pulls the wires out and lets them both hang near the alternator's cable.
2019-06-17 20:11:18] [Output] : ★ Alex Harold then makes his way to the right side of the transmision in order to dettach the clutch wire.
2019-06-17 20:11:37] [Output] : ★ The wire would have a dust cover held in by two bolts.      ((Alex Harold))
2019-06-17 20:11:54] [Output] : ★ Alex Harold picks up the ratchet again and starts twisting each of the two bolts to the left.
2019-06-17 20:12:09] [Output] : ★ Alex Harold slides them out after as well as the cover and sets them aside on the floor.
2019-06-17 20:13:30] [Output] : ★ With the cable now exposed,there would only be one washer holding it in.      ((Alex Harold))
2019-06-17 20:13:56] [Output] : ★ Alex Harold sets the ratchet down and picks up the wrench returning to the washer.
2019-06-17 20:14:06] [Output] : ★ Alex Harold twists the washer to the left in order to get it out.
2019-06-17 20:14:25] [Output] : ★ Alex Harold then puts the wrench down and returns to the cable.
2019-06-17 20:14:48] [Output] : ★ Alex Harold pulls out the cable from the transmision and lets it rest on the ground.
2019-06-17 20:16:27] [Output] : ★ Alex Harold then inspects the transmision to check for all the bolts holding it.
2019-06-17 20:16:57] [Output] : ★ The transmion itself would have eight bolts holding it and the support in the back would...      ((Alex Harold))
2019-06-17 20:17:08] [Output] : ★ Alex Harold ...have two bolts tightened into the chassis.
2019-06-17 20:17:23] [Output] : ★ Alex Harold makes his way to the bunch of tools one more time
2019-06-17 20:17:41] [Output] : ★ Alex Harold picks up the twelve tons jack and returns under the car.
2019-06-17 20:18:50] [Output] : ★ Alex Harold slides the jack under the wooden pallet and starts lifting it up.
2019-06-17 20:19:08] [Output] : ★ As the pallet is lifted up a bit,Alex goes to the driver's wheel      ((Alex Harold))
2019-06-17 20:19:11] [Output] : Alex Harold: (( door* ))
2019-06-17 20:20:28] [Output] : ★ Alex Harold opens up the door and then lowers the lift using it's remote
2019-06-17 20:20:36] [Output] : * Alex Harold presses the button on the ramp controls lowering the car lift. *
2019-06-17 20:21:35] [Output] : ★ Alex Harold steps into the car and makes his way to the center console where the shifter is.
2019-06-17 20:22:09] [Output] : ★ Alex Harold pulls up the cover near of the shifter and places it on the right seat.
2019-06-17 20:22:50] [Output] : ★ As the cover is removed,the shifter would be exposed.      ((Alex Harold))
2019-06-17 20:23:44] [Output] : ★ Alex Harold puts his right hand on the shift knob and starts twisting it to the left,dettaching it.
2019-06-17 20:25:01] [Output] : ★ Alex Harold then puts the knob on the seat near the cover and then inspects the shifter's bolts.
2019-06-17 20:25:32] [Output] : ★ In order to dettach the transmision the shifter and a metal plate have to come off.      ((Alex Harold))
2019-06-17 20:25:35] [Output] : Vehicle spawn position set.
2019-06-17 20:25:45] [Output] : ★ Alex Harold steps out of the vehicle and picks up the ratchet.
2019-06-17 20:25:57] [Output] : ★ Alex Harold then returns into the car and starts working on the shifter.
2019-06-17 20:26:25] [Output] : ★ The shifter would have four bolts holding it into the transmision.      ((Alex Harold))
2019-06-17 20:26:34] [Output] :  [English] Alex Harold ((In Car)) says: Right,so I only have to take out the bottom bolts.
2019-06-17 20:26:54] [Output] : ★ Alex Harold puts the ratchet on one of the bolts and starts rotating it to the left,dettaching it.
2019-06-17 20:27:06] [Output] : ★ Alex Harold then reapeats the process for the second bolt and places them both on the seat.
2019-06-17 20:28:35] [Output] : ★ Alex Harold pulls up the shifter after and places it on the floor at the passenger's seat
2019-06-17 20:30:34] [Output] : ★ Alex Harold then uses his ratchet and starts taking out the four bolts holding the plate and the...
2019-06-17 20:30:41] [Output] : ★ Alex Harold ..transmision to the interior
2019-06-17 20:31:27] [Output] : ★ Alex Harold then picks up the plate along with the bolts and places it near the shifter.
2019-06-17 20:31:39] [Output] : ★ Alex Harold then takes the ratchet and steps out of the car.
2019-06-17 20:31:41] [Output] : Vehicle spawn position set.
2019-06-17 20:32:25] [Output] : ★ Alex Harold uses the remote again and raises up the lift.
2019-06-17 20:32:30] [Output] : * Alex Harold presses the button on the ramp controls raising the car lift. *
2019-06-17 20:32:52] [Output] : ★ Alex Harold pulls the jack's lever up all the way,getting the pallet under the transmision
2019-06-17 20:33:06] [Output] : ★ Alex Harold then puts the ratchet down and picks up his impact gun
2019-06-17 20:33:20] [Output] : ★ Alex Harold goes under the car after to dettach the bolts.
2019-06-17 20:33:40] [Output] : ★ Alex Harold goes to the back of the transmision  in order to dettach the support arm from the chassis
2019-06-17 20:34:03] [Output] : ★ Alex Harold starts up the impact gun and dettaches the two bolts,placing them near the axles.
2019-06-17 20:34:29] [Output] : ★ Alex Harold then goes to the front side of the transmisions in order to take out the eight bolts holding
2019-06-17 20:34:34] [Output] : ★ Alex Harold ...it to the engine block.
2019-06-17 20:35:12] [Output] : ★ Alex Harold starts up the impact gun and dettaches all the eight bolts in a row.
2019-06-17 20:35:36] [Output] : ★ Alex Harold then places the bolts near the other two ones and locks the jack with his left foot.
2019-06-17 20:36:12] [Output] : ★ Alex Harold would then wiggle the transmision a back a little to dettach it from the engine
2019-06-17 20:36:26] [Output] : ★ With the transmision now dettached,Alex would be able to lower it down.      ((Alex Harold))
2019-06-17 20:36:40] [Output] : ★ Alex Harold pulls the jack's lever down,lowering the transmision.
2019-06-17 20:37:07] [Output] : ★ Alex Harold then drags the pallet with his jack and makes the way of the gearbox in a safe place
[2019-06-07 15:42:20] [Output] : ★ The only pieces left to dettach to take the engine out would be the clutch assembly and...      ((Alex Harold))
[2019-06-07 15:42:31] [Output] : ★ ...the four engine mounts.      ((Alex Harold))
[2019-06-07 15:42:52] [Output] : ★ Alex Harold heads to the clutch and inspects it around to see the bolts holding it.
[2019-06-07 15:43:36] [Output] : ★ There would be six bolts holding the pressure plate on the clutch plate.      ((Alex Harold))
[2019-06-07 15:44:41] [Output] : ★ Alex Harold heads to the back of the car where his impact gun would be left.
[2019-06-07 15:44:54] [Output] : ★ Alex Harold then picks up the impact gun and returns to the pressure plate.
[2019-06-07 15:45:12] [Output] : ★ Alex Harold lowers down the lift a bit to get the car closer to him
[2019-06-07 15:45:16] [Output] : * Alex Harold presses the button on the ramp controls lowering the car lift. *
[2019-06-07 15:45:19] [Output] : * Alex Harold presses the button on the ramp controls lowering the car lift. *
[2019-06-07 15:45:38] [Output] : ★ Alex Harold extends his arms to the plate and sets his left arm on it to lock it in place.
[2019-06-07 15:46:06] [Output] : ★ Alex Harold then starts up his impact gun and removes the six bolts holding the plate one after the othe
[2019-06-07 15:46:09] [Output] : Alex Harold: (( other* ))
[2019-06-07 15:46:23] [Output] : ★ Alex Harold then drops the bolts down and places his both hands on the pressure plate.
[2019-06-07 15:46:34] [Output] : ★ Alex Harold slowly lowers the plate from it's place,dragging it backwards
[2019-06-07 15:46:58] [Output] : ★ Alex Harold then leans over to the floor on the left side of the car to let down the plate
[2019-06-07 15:47:17] [Output] : ★ Alex Harold puts the clutch pressure plate on the floor and then returns to the car.
[2019-06-07 15:47:44] [Output] : ★ The only parts left in place would be the clutch plate,the middle bearing and the flywheel.      ((Alex Harold))
[2019-06-07 15:47:54] [Output] : ★ Alex Harold leans over to the floor and places his impact gun down.
[2019-06-07 15:48:11] [Output] : ★ Alex Harold would then make his way to the bunch of tools in order to pick up a bearing wrench
[2019-06-07 15:48:32] [Output] : ★ Alex Harold leans over the tools and searches for the bearing wrench
[2019-06-07 15:48:43] [Output] : ★ Alex Harold finds it and picks it up returning to the car.
[2019-06-07 15:50:08] [Output] : ★ Alex Harold inserts the wrench into the middle bolt and slides it all the way in.
[2019-06-07 15:51:15] [Output] : ★ Alex Harold then uses the wrench's lever and makes the arms slides behind the bearing.
[2019-06-07 15:51:28] [Output] : ★ As the bearing is now locked up,Alex would be able to pull it.      ((Alex Harold))
[2019-06-07 15:51:48] [Output] : ★ Alex Harold slides out the wrench along with the bearing,placing them both down near the axles.
[2019-06-07 15:52:28] [Output] : ★ Alex Harold returns to the clutch after and makes his way further in the process
[2019-06-07 15:52:50] [Output] : ★ Alex Harold places his hands on the clutch plate and slides it out of it's place.
[2019-06-07 15:53:06] [Output] : ★ Alex Harold then picks up the plate and returns where the pressure plate is placed.
[2019-06-07 15:53:31] [Output] : ★ Alex Harold lets down the clutch plate and further returns to the car.
[2019-06-07 15:53:47] [Output] : ★ Alex Harold inspects the flywheel to check for the bolts holding it.
[2019-06-07 15:54:42] [Output] : ★ As noticed,the fly wheel would have six bolts holding it to the engine block.      ((Alex Harold))
[2019-06-07 15:54:51] [Output] : ★ Alex Harold leans over to the ground and picks up his impact gun.
[2019-06-07 15:55:01] [Output] : ★ Alex Harold then returns up to the flywheel in order to get it out.
[2019-06-07 15:55:25] [Output] : ★ Alex Harold places his left hand on the flywheel,preventing it from spining and starts dettaching the...
[2019-06-07 15:55:31] [Output] : ★ Alex Harold ...bolts from the top to the bottom.
[2019-06-07 16:02:40] [Output] : ★ Alex Harold then slides out the six bolts,throwing them on the ground
[2019-06-07 16:02:57] [Output] : ★ Alex Harold places his both hands on the flywheel then,further sliding it out.
[2019-06-07 16:03:22] [Output] : ★ Alex Harold makes his way with the flywheel in his hands in order to place it near the other clutch part
[2019-06-07 16:03:35] [Output] : ★ Alex Harold lets the flywheel down and returns to the car
[2019-06-08 12:21:40] [Output] : ★ Alex Harold looks over to the engine bay spotting the four engine mounts.
[2019-06-08 12:22:11] [Output] : ★ Alex Harold then checks the bolts holding the mounts,noticing that they can be take off from the top
[2019-06-08 12:23:00] [Output] : ★ Alex Harold heads into the towtruck in order to use it to lift the engine up
[2019-06-08 12:24:18] [Output] : ★ The remote controling the towtruck's hook would be sitting on the dash      ((Alex Harold))
[2019-06-08 12:24:45] [Output] : ★ Alex Harold grabs the remote in his hands and then easily pushes the bottom button until the hook gets..
[2019-06-08 12:24:49] [Output] : ★ Alex Harold ...on top of the engine
[2019-06-08 12:25:57] [Output] : ★ Alex Harold then puts the remote back  on the dash and steps out,returning to the engine.
[2019-06-08 12:26:31] [Output] : ★ Alex Harold then drags the hook under the middle strap,lifting it up.
[2019-06-08 12:26:42] [Output] : ★ Alex Harold returns into the truck in order to lift up the hook.
[2019-06-08 12:27:11] [Output] : ★ Alex Harold grabs the remote from the dash and pushes it's upper button .
[2019-06-08 12:27:31] [Output] : ★ As the hook raises up the strap holding it,Alex stops.      ((Alex Harold))
[2019-06-08 12:27:59] [Output] : ★ Alex Harold returns to the car after in order to dettach the four mounts.
[2019-06-08 12:28:16] [Output] : ★ The impact gun would be sitting on the floor,on the right side of the car.      ((Alex Harold))
[2019-06-08 12:28:36] [Output] : ★ Alex Harold leans over to the floor and picks the impact gun up.
[2019-06-08 12:28:52] [Output] : ★ Alex Harold then heads into the engine bay and points the first engine mount.
[2019-06-08 12:29:03] [Output] : ★ There would be one bolt holding each mount to the chassis.      ((Alex Harold))
[2019-06-08 12:29:59] [Output] : ★ Alex Harold starts up the impact gun and dettaches the first bolt,placing it in the back of the towtruck
[2019-06-08 12:30:08] [Output] : ★ Alex Harold then makes his way to the second mount
[2019-06-08 12:30:27] [Output] : ★ Alex Harold positions the impact gun on top of it and starts it up to dettach the bolt.
[2019-06-08 12:30:44] [Output] : ★ Alex Harold then picks the bolt up,placing it on the back of the truck.
[2019-06-08 12:31:04] [Output] : ★ Alex Harold then heads to the opposite side of the car and repeats the same exact process for the two...
[2019-06-08 12:31:11] [Output] : ★ Alex Harold ...remaining mounts.
[2019-06-08 12:31:31] [Output] : ★ As the mounts are now dettached from the chassis,they would come off with the engine      ((Alex Harold))
[2019-06-08 12:32:08] [Output] : ★ Alex Harold makes his way to the towtruck and steps inside it.
[2019-06-08 12:32:27] [Output] : ★ Alex Harold grabs the remote and uses it's top button to raise up the engine from the bay
[2019-06-08 12:32:48] [Output] : ★ As the hook is slowly lifted,the engine leaves the bay      ((Alex Harold))
[2019-06-08 12:33:06] [Output] : ★ Alex Harold then drives slowly forward,taking it fully out
[2019-06-08 12:33:35] [Output] : ★ Alex Harold stops after he turns and steps back again from the towtruck
[2019-06-08 12:33:55] [Output] : ★ You would now be able to see the engine hanging from the hook      ((Alex Harold))
[2019-06-08 12:34:20] [Output] : ★ Alex Harold then makes his way to pick the engine stand up and moove it to the engine.
[2019-06-08 12:35:04] [Output] : ★ Alex Harold gets at the back of the engine stand,pushing it on it's wheels to the back of the engine
[2019-06-08 12:35:33] [Output] : ★ Alex Harold then makes his way to the back of the engine without the crane in order to pick up...
[2019-06-08 12:35:42] [Output] : ★ Alex Harold ...the metal gasket of the gearbox.
[2019-06-08 12:36:01] [Output] : ★ Alex Harold grabs the gasket out with his hands and places it near the car
[2019-06-08 12:36:28] [Output] : ★ Alex Harold then returns to the back of the stand and slowly pushes it
[2019-06-08 12:37:00] [Output] : ★ Alex Harold starts pushing the stand a bit bit a bit getting it close to the engine
[2019-06-08 12:37:18] [Output] : ★ Alex Harold then steps inside the towtruck in order to lower the hook
[2019-06-08 12:37:51] [Output] : ★ Alex Harold grabs the hook's remote and lowers down the hook making the engine sit near the stand.
[2019-06-08 12:38:17] [Output] : ★ Alex Harold then lets down the remote and steps back out
[2019-06-08 12:38:29] [Output] : ★ Alex Harold makes his way to the stand again further pushing it
[2019-06-08 12:38:45] [Output] : ★ Alex Harold pushes down the stand a bit until he reminds of something.
[2019-06-08 12:39:00] [Output] : ★ Alex Harold heads over to the impact gun,picking it up
[2019-06-08 12:39:15] [Output] : ★ Alex Harold leans over to the impact gun and makes his way to the front of the engine stand.
[2019-06-08 12:40:18] [Output] : ★ There would be eight bolts tightened over the holes of the stand.      ((Alex Harold))
[2019-06-08 12:40:43] [Output] : ★ Alex Harold starts the impact gun up and dettaches the eight bolts one by one,placing them on the ground
[2019-06-08 12:40:58] [Output] : ★ Alex Harold then makes his way to the back of the stand and starts pushing it to hit the holes.
[2019-06-08 12:41:28] [Output] : ★ Alex Harold pushes the stand until the holes stand over the transmision holes.
[2019-06-08 12:41:44] [Output] : ★ Alex Harold then slowly allings the stand and then uses his left foot to engage his brake.
[2019-06-08 12:44:07] [Output] : ★ Alex Harold lets the stand free after and leans over to the ground
[2019-06-08 12:44:22] [Output] : ★ Alex Harold picks up the eight bolts and heads to the back of the stand.
[2019-06-08 12:46:15] [Output] : ★ Alex Harold inserts the bolts in the holes,twisting each of them in the engine.
[2019-06-08 12:46:35] [Output] : ★ Alex Harold then uses his impact gun and tigthens them up in a criss cross pattern.