API tools faq
paste
Guest User

Strong 1200 dmesg original firmware

a guest
Oct 4th, 2018
664
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 15.25 KB | None | 0 0
raw download clone embed print report
  1. # dmesg
  2. dmesg
  3. 16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
  4. Creating 6 MTD partitions on "raspi":
  5. 0x000000000000-0x000001000000 : "ALL"
  6. 0x000000000000-0x000000030000 : "Bootloader"
  7. 0x000000030000-0x000000040000 : "Config"
  8. 0x000000040000-0x000000050000 : "Factory"
  9. 0x000000050000-0x000000ff0000 : "Kernel"
  10. 0x000000ff0000-0x000001000000 : "Second_Config"
  11. rdm_major = 253
  12. GMAC1_MAC_ADRH -- : 0x0000000c
  13. GMAC1_MAC_ADRL -- : 0x43288054
  14. Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500!
  15. GMAC1_MAC_ADRH -- : 0x0000000c
  16. GMAC1_MAC_ADRL -- : 0x43288022
  17. PROC INIT OK!
  18. PPP generic driver version 2.4.2
  19. PPP BSD Compression module registered
  20. PPP MPPE Compression module registered
  21. NET: Registered protocol family 24
  22. PPTP driver version 0.8.5
  23. IMQ driver loaded successfully.
  24. Hooking IMQ before NAT on PREROUTING.
  25. Hooking IMQ after NAT on POSTROUTING.
  26. usbcore: registered new interface driver catc
  27. catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
  28. usbcore: registered new interface driver asix
  29. usbcore: registered new interface driver ax88179_178a
  30. usbcore: registered new interface driver cdc_ether
  31. usbcore: registered new interface driver net1080
  32. usbcore: registered new interface driver cdc_subset
  33. usbcore: registered new interface driver zaurus
  34. register rt2860
  35. PCI: Setting latency timer of device 0000:01:00.0 to 64
  36.  
  37.  
  38. === pAd = c0282000, size = 2173440 ===
  39.  
  40. RTMPAllocTxRxRingMemory, Status=0
  41. RTMPAllocAdapterBlock, Status=0
  42. pAd->CSRBaseAddress =0xc0180000, csr_addr=0xc0180000!
  43. device_id =0x7662
  44. ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
  45. RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
  46. RtmpEepromGetDefault::e2p_dafault=3
  47. NVM is efuse and the information is too less to bring up the interface
  48. Force to use Flash mode
  49. NVM is FLASH mode (pAd->flash_offset = 0x48000)
  50. get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
  51. PCI: Setting latency timer of device 0000:02:00.0 to 64
  52.  
  53.  
  54. === pAd = c0602000, size = 2173440 ===
  55.  
  56. RTMPAllocTxRxRingMemory, Status=0
  57. RTMPAllocAdapterBlock, Status=0
  58. pAd->CSRBaseAddress =0xc0500000, csr_addr=0xc0500000!
  59. device_id =0x7662
  60. ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
  61. RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
  62. RtmpEepromGetDefault::e2p_dafault=3
  63. NVM is efuse and the information is too less to bring up the interface
  64. Force to use Flash mode
  65. NVM is FLASH mode (pAd->flash_offset = 0x40000)
  66. get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=ra
  67. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  68. ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  69. FM_OUT value: u4FmOut = 0(0x00000000)
  70. FM_OUT value: u4FmOut = 0(0x00000000)
  71. FM_OUT value: u4FmOut = 0(0x00000000)
  72. FM_OUT value: u4FmOut = 0(0x00000000)
  73. FM_OUT value: u4FmOut = 0(0x00000000)
  74. FM_OUT value: u4FmOut = 0(0x00000000)
  75. FM_OUT value: u4FmOut = 0(0x00000000)
  76. FM_OUT value: u4FmOut = 0(0x00000000)
  77. FM_OUT value: u4FmOut = 0(0x00000000)
  78. FM_OUT value: u4FmOut = 0(0x00000000)
  79. FM_OUT value: u4FmOut = 0(0x00000000)
  80. FM_OUT value: u4FmOut = 0(0x00000000)
  81. FM_OUT value: u4FmOut = 0(0x00000000)
  82. FM_OUT value: u4FmOut = 0(0x00000000)
  83. FM_OUT value: u4FmOut = 0(0x00000000)
  84. FM_OUT value: u4FmOut = 0(0x00000000)
  85. FM_OUT value: u4FmOut = 0(0x00000000)
  86. FM_OUT value: u4FmOut = 0(0x00000000)
  87. FM_OUT value: u4FmOut = 0(0x00000000)
  88. FM_OUT value: u4FmOut = 0(0x00000000)
  89. xhc_mtk xhc_mtk: xHCI Host Controller
  90. xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 1
  91. xhc_mtk xhc_mtk: irq 22, io mem 0x1e1c0000
  92. xHCI xhci_add_endpoint called for root hub
  93. xHCI xhci_check_bandwidth called for root hub
  94. hub 1-0:1.0: USB hub found
  95. hub 1-0:1.0: 2 ports detected
  96. xhc_mtk xhc_mtk: xHCI Host Controller
  97. xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 2
  98. xHCI xhci_add_endpoint called for root hub
  99. xHCI xhci_check_bandwidth called for root hub
  100. hub 2-0:1.0: USB hub found
  101. hub 2-0:1.0: 1 port detected
  102. usbcore: registered new interface driver usbserial
  103. USB Serial support registered for generic
  104. usbcore: registered new interface driver usbserial_generic
  105. usbserial: USB Serial Driver core
  106. Netfilter messages via NETLINK v0.30.
  107. nf_conntrack version 0.5.0 (1845 buckets, 7380 max)
  108. matchsize=264
  109. xt_time: kernel timezone is -0000
  110. IPVS: Registered protocols ()
  111. IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
  112. IPVS: ipvs loaded.
  113. GRE over IPv4 demultiplexor driver
  114. gre: can't add protocol
  115. ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
  116. ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
  117. arp_tables: (C) 2002 David S. Miller
  118. TCP cubic registered
  119. NET: Registered protocol family 17
  120. L2TP core driver, V2.0
  121. PPPoL2TP kernel driver, V2.0
  122. 802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
  123. All bugs added by David S. Miller <[email protected]>
  124. >>>wsc_negotiate_info_init:r[0]<<<
  125. >>>private_domain_init:r[0]<<<
  126. Warning: unable to open an initial console.
  127. Freeing unused kernel memory: 5040k freed
  128. Algorithmics/MIPS FPU Emulator v1.5
  129. >>>PRIVATE_DOMAIN_IOCTL_SET g_sz_private_domain=strong.1200.wr<<<
  130. >>>PRIVATE_DOMAIN_IOCTL_GET g_sz_private_domain=strong.1200.wr<<<
  131. Raeth v3.1 (Tasklet)
  132. phy_free_head is 0x5e06000!!!
  133. phy_free_tail_phy is 0x5e07ff0!!!
  134. txd_pool=a5e08000 phy_txd_pool=05E08000
  135. ei_local->skb_free start address is 0x87ce9494.
  136. free_txd: a5e08010, ei_local->cpu_ptr: 05E08000
  137. POOL HEAD_PTR | DMA_PTR | CPU_PTR
  138. ----------------+---------+--------
  139. 0xa5e08000 0x05E08000 0x05E08000
  140.  
  141. phy_qrx_ring = 0x05e01000, qrx_ring = 0xa5e01000
  142.  
  143. phy_rx_ring0 = 0x05e0a000, rx_ring0 = 0xa5e0a000
  144. change HW-TRAP to 0x17ccf
  145. set LAN/WAN LLLLW
  146. GMAC1_MAC_ADRH -- : 0x0000000c
  147. GMAC1_MAC_ADRL -- : 0x43288022
  148. CDMA_CSG_CFG = 81000000
  149. GDMA1_FWD_CFG = 20710000
  150. ra2880stop()...Done
  151. Free TX/RX Ring Memory!
  152. Raeth v3.1 (Tasklet)
  153. phy_free_head is 0x5d86000!!!
  154. phy_free_tail_phy is 0x5d87ff0!!!
  155. txd_pool=a5d60000 phy_txd_pool=05D60000
  156. ei_local->skb_free start address is 0x87ce9494.
  157. free_txd: a5d60010, ei_local->cpu_ptr: 05D60000
  158. POOL HEAD_PTR | DMA_PTR | CPU_PTR
  159. ----------------+---------+--------
  160. 0xa5d60000 0x05D60000 0x05D60000
  161.  
  162. phy_qrx_ring = 0x05d81000, qrx_ring = 0xa5d81000
  163.  
  164. phy_rx_ring0 = 0x05d62000, rx_ring0 = 0xa5d62000
  165. change HW-TRAP to 0x17ccf
  166. set LAN/WAN LLLLW
  167. GMAC1_MAC_ADRH -- : 0x00000016
  168. GMAC1_MAC_ADRL -- : 0xfbc6a38e
  169. CDMA_CSG_CFG = 81000000
  170. GDMA1_FWD_CFG = 20710000
  171. device eth2 entered promiscuous mode
  172. device eth2.1 entered promiscuous mode
  173. br0: port 1(eth2.1) entering learning state
  174. br0: port 1(eth2.1) entering learning state
  175. br0: port 1(eth2.1) entering forwarding state
  176. ESW: Link Status Changed - Port3 Link UP
  177. build time =
  178. 20141115060606a
  179. rom patch for E3 IC
  180.  
  181. platform =
  182. ALPS
  183. hw/sw version =
  184. ��
  185. patch version =
  186. 
  187. FW Version:0.0.00 Build:1
  188. Build Time:201507311614____
  189. fw for E3 IC
  190. RX[0] DESC a6390000 size = 4096
  191. RX[1] DESC a6391000 size = 4096
  192. E2pAccessMode=0
  193. cfg_mode=9
  194. cfg_mode=9
  195. wmode_band_equal(): Band Equal!
  196. APSDCapable[0]=0
  197. APSDCapable[1]=0
  198. APSDCapable[2]=0
  199. APSDCapable[3]=0
  200. APSDCapable[4]=0
  201. APSDCapable[5]=0
  202. APSDCapable[6]=0
  203. APSDCapable[7]=0
  204. APSDCapable[8]=0
  205. APSDCapable[9]=0
  206. APSDCapable[10]=0
  207. APSDCapable[11]=0
  208. APSDCapable[12]=0
  209. APSDCapable[13]=0
  210. APSDCapable[14]=0
  211. APSDCapable[15]=0
  212. default ApCliAPSDCapable[0]=0
  213. Key1Str is Invalid key length(0) or Type(0)
  214. Key2Str is Invalid key length(0) or Type(0)
  215. Key3Str is Invalid key length(0) or Type(0)
  216. Key4Str is Invalid key length(0) or Type(0)
  217. 1. Phy Mode = 14
  218. get_chl_grp:illegal channel (167)
  219. get_chl_grp:illegal channel (167)
  220. get_chl_grp:illegal channel (169)
  221. get_chl_grp:illegal channel (169)
  222. get_chl_grp:illegal channel (171)
  223. get_chl_grp:illegal channel (171)
  224. drivers/net/wireless/rlt_wifi_ap/../rlt_wifi/chips/mt76x2.c:2899 assert (ad->TxPower[choffset].Channel == 42)failed
  225. Country Region from e2p = ffff
  226. mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0
  227. mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=2
  228. mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=0, low_temp_slope=0
  229. mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=13, low_temp_slope=16
  230. mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=0, tc_upper_bound=0
  231. mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=-7, tc_upper_bound=5
  232. mt76x2_get_external_lna_gain::LNA type=0x10, BLNAGain=0xffffff8e, ALNAGain0=0xffffff8c, ALNAGain1=0xffffff8c, ALNAGain2=0xffffff8c
  233. 2. Phy Mode = 14
  234. 3. Phy Mode = 14
  235. andes_pci_fw_init
  236. 0x1300 = 00073200
  237. AntCfgInit: primary/secondary ant 0/1
  238. andes_load_cr:cr_type(2)
  239. ChipStructAssign(): MT76x2 hook !
  240. RTMPSetPhyMode: channel is out of range, use first channel=0
  241. MCS Set = ff ff 00 00 01
  242. =====================================================
  243. Channel 1 : Dirty = 35, ApCnt=6, Busy Time = 0, Skip Channel = FALSE
  244. Channel 2 : Dirty = 6, ApCnt=0, Busy Time = 0, Skip Channel = FALSE
  245. Channel 3 : Dirty = 36, ApCnt=2, Busy Time = 0, Skip Channel = FALSE
  246. Channel 4 : Dirty = 36, ApCnt=1, Busy Time = 0, Skip Channel = FALSE
  247. Channel 5 : Dirty = 7, ApCnt=0, Busy Time = 0, Skip Channel = FALSE
  248. Channel 6 : Dirty = 35, ApCnt=6, Busy Time = 0, Skip Channel = FALSE
  249. Channel 7 : Dirty = 35, ApCnt=1, Busy Time = 0, Skip Channel = FALSE
  250. Channel 8 : Dirty = 5, ApCnt=0, Busy Time = 0, Skip Channel = FALSE
  251. Channel 9 : Dirty = 33, ApCnt=1, Busy Time = 0, Skip Channel = FALSE
  252. Channel 10 : Dirty = 4, ApCnt=0, Busy Time = 0, Skip Channel = FALSE
  253. Channel 11 : Dirty = 32, ApCnt=4, Busy Time = 0, Skip Channel = FALSE
  254. Channel 12 : Dirty = 2, ApCnt=0, Busy Time = 0, Skip Channel = TRUE
  255. Channel 13 : Dirty = 2, ApCnt=1, Busy Time = 0, Skip Channel = TRUE
  256. =====================================================
  257. Rule 2 APCnt : minimum APCnt with minimum interference(dirtiness: 30~32) ==> Select Channel 11
  258. Dirtiness = 32 , Min ApCnt = 4
  259. mt76x2_bbp_adjust():rf_bw=1, ext_ch=3, PrimCh=11, HT-CentCh=9, VHT-CentCh=0
  260. APStartUp(): AP Set CentralFreq at 9(Prim=11, HT-CentCh=9, VHT-CentCh=0, BBP_BW=1)
  261. mt76x2_calibration(channel = 9)
  262. @@@ ed_monitor_init : ===>
  263. @@@ ed_monitor_init : <===
  264. Main bssid = 00:16:fb:c6:a3:8c
  265. mt76x2_reinit_agc_gain:original agc_vga0 = 0x44, agc_vga1 = 0x44
  266. mt76x2_reinit_agc_gain:updated agc_vga0 = 0x44, agc_vga1 = 0x44
  267. mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x35, hi_lna1 = 0x35
  268. mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x35, hi_lna1 = 0x35
  269. original vga value(chain0) = 44
  270. original vga value(chain1) = 44
  271. == rt28xx_init, Status=0
  272. get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=apcli
  273. RTMPDrvOpen(1):Check if PDMA is idle!
  274. RTMPDrvOpen(2):Check if PDMA is idle!
  275. @@@ ed_monitor_init : ===>
  276. @@@ ed_monitor_init : <===
  277. device ra0 entered promiscuous mode
  278. br0: port 2(ra0) entering learning state
  279. br0: port 2(ra0) entering learning state
  280. build time =
  281. 20141115060606a
  282. rom patch for E3 IC
  283.  
  284. platform =
  285. ALPS
  286. hw/sw version =
  287. ��
  288. patch version =
  289. 
  290. FW Version:0.0.00 Build:1
  291. Build Time:201507311614____
  292. fw for E3 IC
  293. RX[0] DESC a611c000 size = 4096
  294. RX[1] DESC a611d000 size = 4096
  295. E2pAccessMode=0
  296. cfg_mode=14
  297. cfg_mode=14
  298. wmode_band_equal(): Band Not Equal!
  299. APSDCapable[0]=0
  300. APSDCapable[1]=0
  301. APSDCapable[2]=0
  302. APSDCapable[3]=0
  303. APSDCapable[4]=0
  304. APSDCapable[5]=0
  305. APSDCapable[6]=0
  306. APSDCapable[7]=0
  307. APSDCapable[8]=0
  308. APSDCapable[9]=0
  309. APSDCapable[10]=0
  310. APSDCapable[11]=0
  311. APSDCapable[12]=0
  312. APSDCapable[13]=0
  313. APSDCapable[14]=0
  314. APSDCapable[15]=0
  315. default ApCliAPSDCapable[0]=0
  316. edcca_tx_stop_start():stop tx
  317. Key1Str is Invalid key length(0) or Type(0)
  318. Key2Str is Invalid key length(0) or Type(0)
  319. Key3Str is Invalid key length(0) or Type(0)
  320. Key4Str is Invalid key length(0) or Type(0)
  321. 1. Phy Mode = 49
  322. get_chl_grp:illegal channel (167)
  323. get_chl_grp:illegal channel (167)
  324. get_chl_grp:illegal channel (169)
  325. get_chl_grp:illegal channel (169)
  326. get_chl_grp:illegal channel (171)
  327. get_chl_grp:illegal channel (171)
  328. drivers/net/wireless/rlt_wifi_ap/../rlt_wifi/chips/mt76x2.c:2899 assert (ad->TxPower[choffset].Channel == 42)failed
  329. Country Region from e2p = ffff
  330. mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0
  331. mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=0
  332. mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=15, low_temp_slope=9
  333. mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=13, low_temp_slope=16
  334. mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4
  335. mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=-7, tc_upper_bound=5
  336. mt76x2_get_external_lna_gain::LNA type=0x0, BLNAGain=0xffffff8c, ALNAGain0=0xffffff8c, ALNAGain1=0xffffff8c, ALNAGain2=0xffffff8c
  337. 2. Phy Mode = 49
  338. 3. Phy Mode = 49
  339. andes_pci_fw_init
  340. 0x1300 = 00073200
  341. AntCfgInit: primary/secondary ant 0/1
  342. andes_load_cr:cr_type(2)
  343. ChipStructAssign(): MT76x2 hook !
  344. RTMPSetPhyMode: channel is out of range, use first channel=0
  345. MCS Set = ff ff 00 00 00
  346. br0: port 2(ra0) entering forwarding state
  347. =====================================================
  348. Channel 36 : Dirty = 32, ApCnt=3, Busy Time = 0, Skip Channel = FALSE
  349. Channel 40 : Dirty = 2, ApCnt=0, Busy Time = 0, Skip Channel = FALSE
  350. Channel 44 : Dirty = 2, ApCnt=0, Busy Time = 0, Skip Channel = FALSE
  351. Channel 48 : Dirty = 32, ApCnt=1, Busy Time = 0, Skip Channel = FALSE
  352. =====================================================
  353. Rule 2 APCnt : minimum APCnt with minimum interference(dirtiness: 30~32) ==> Select Channel 48
  354. Dirtiness = 32 , Min ApCnt = 1
  355. mt76x2_bbp_adjust():rf_bw=0, ext_ch=0, PrimCh=48, HT-CentCh=48, VHT-CentCh=42
  356. APStartUp(): AP Set CentralFreq at 48(Prim=48, HT-CentCh=48, VHT-CentCh=42, BBP_BW=0)
  357. mt76x2_calibration(channel = 48)
  358. @@@ ed_monitor_init : ===>
  359. @@@ ed_monitor_init : <===
  360. Main bssid = 00:16:fb:c6:b3:8c
  361. mt76x2_reinit_agc_gain:original agc_vga0 = 0x4a, agc_vga1 = 0x4a
  362. mt76x2_reinit_agc_gain:updated agc_vga0 = 0x4a, agc_vga1 = 0x4a
  363. mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x33, hi_lna1 = 0x33
  364. mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x33, hi_lna1 = 0x33
  365. original vga value(chain0) = 4a
  366. original vga value(chain1) = 4a
  367. == rt28xx_init, Status=0
  368. get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=apclii
  369. RTMPDrvOpen(1):Check if PDMA is idle!
  370. RTMPDrvOpen(2):Check if PDMA is idle!
  371. @@@ ed_monitor_init : ===>
  372. @@@ ed_monitor_init : <===
  373. device rai0 entered promiscuous mode
  374. br0: port 3(rai0) entering learning state
  375. br0: port 3(rai0) entering learning state
  376. set_ed_chk_proc(): ed_chk=0
  377. @@@ ed_monitor_exit : ===>
  378. @@@ ed_monitor_exit : <===
  379. edcca_tx_stop_start():start tx
  380. set_ed_chk_proc(): ed_chk=1
  381. @@@ ed_monitor_init : ===>
  382. @@@ ed_monitor_init : <===
  383. >>>WSC_NEGOTIATE_INFO_REG_PID program_pid=1371<<<
  384. br0: port 3(rai0) entering forwarding state
  385. Initializing USB Mass Storage driver...
  386. usbcore: registered new interface driver usb-storage
  387. USB Mass Storage support registered.
  388. MTK MSDC device init.
  389. msdc0 -> ops_get_cd return<0> <- msdc_ops_get_cd() : L<2317> PID<kworker/u:1><0x1a>
  390. mtk-sd: MediaTek MT6575 MSDC Driver
  391. usbcore: registered new interface driver usblp
  392. ESW: Link Status Changed - Port3 Link Down
  393. ESW: Link Status Changed - Port3 Link UP
  394. ESW: Link Status Changed - Port3 Link Down
  395. ESW: Link Status Changed - Port3 Link UP
  396. ESW: Link Status Changed - Port3 Link Down
  397. ESW: Link Status Changed - Port3 Link UP
  398. ESW: Link Status Changed - Port3 Link Down
  399. ESW: Link Status Changed - Port3 Link UP
Advertisement
Add Comment
Please, Sign In to add comment
Public Pastes
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!