BusyBox v1.15.3 (2011-11-24 02:12:13 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 Backfire (10.03.1, r29592) ------------------------
  * 1/3 shot Kahlua    In a shot glass, layer Kahlua
  * 1/3 shot Bailey's  on the bottom, then Bailey's,
  * 1/3 shot Vodka     then Vodka.
 ---------------------------------------------------
root@OpenWrt:/# dmesg
CPU revision is: 00029006
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Linux version 2.4.37.9 ([email protected]) (gcc version 3.4.6 (OpenWrt-2.0)) #12 Wed Dec 21 03:33:39 CET 2011
Setting the PFC to its default value
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd console=ttyS0,115200
CPU: BCM4704 rev 8 at 264 MHz
Using 132.000 MHz high precision timer.
Calibrating delay loop... 263.78 BogoMIPS
Memory: 62856k/65536k available (1457k kernel code, 2680k reserved, 100k data, 84k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
PCI: Initializing host
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Setting latency timer of device 01:00.0 to 64
PCI: Fixing up bus 1
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Registering mini_fo version $Id$
devfs: v1.12c (20020818) Richard Gooch ([email protected])
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xb8000300 (irq = 3) is a 16550A
ttyS01 at 0xb8000400 (irq = 3) is a 16550A
b44.c:v0.93 (Mar, 2004)
PCI: Setting latency timer of device 00:01.0 to 64
eth0: Broadcom 47xx 10/100BaseT Ethernet 00:17:31:ba:e4:4a
PCI: Setting latency timer of device 00:02.0 to 64
eth1: Broadcom 47xx 10/100BaseT Ethernet 40:10:18:00:00:2c
Physically mapped flash: Found an alias at 0x200000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x600000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xa00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xe00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1200000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1600000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1a00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1e00000 for the chip at 0x0
 Amd/Fujitsu Extended Query Table v1.0 at 0x0040
Physically mapped flash: JEDEC Device ID is 0xC4. Assuming broken CFI table.
Physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Flash device: 0x200000 at 0x1c000000
bootloader size: 262144
Physically mapped flash: Filesystem type: squashfs, size=0x1142d3
Updating TRX offsets and length:
old trx = [0x0000001c, 0x00000904, 0x0007d400], len=0x001c1000 crc32=0x12af35f0
new trx = [0x0000001c, 0x00000904, 0x0007d400], len=0x001a0000 crc32=0x9454e070
Done
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x001f0000 : "linux"
0x000bd400-0x001e0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x001f0000-0x00200000 : "nvram"
0x001e0000-0x001f0000 : "rootfs_data"
sflash: found no supported devices
Initializing Cryptographic API
IEEE 802.2 LLC for Linux 2.1 (c) 1996 Tim Alpaerts
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
All bugs added by David S. Miller <[email protected]>
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 84k freed
diag: Detected 'ASUS WL-700gE'
diag: Spinning up HDD and enabling leds
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
roboswitch: Probing device eth0: found a 5325! It's a 5350.
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
jffs2.bbc: SIZE compression mode activated.
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
eth0.0: add 01:00:5e:00:00:01 mcast address to master interface
eth0.1: add 01:00:5e:00:00:01 mcast address to master interface
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
eth0.0: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
device eth0.0 entered promiscuous mode
eth0.1: del 01:00:5e:00:00:01 mcast address from vlan interface
eth0.1: del 01:00:5e:00:00:01 mcast address from master interface
eth0.1: Setting MAC address to  00 17 31 ba e4 4b.
eth0.1: add 01:00:5e:00:00:01 mcast address to master interface
AEC6X80: IDE controller at PCI slot 01:02.0
PCI: Enabling device 01:02.0 (0000 -> 0003)
AEC6X80: chipset revision 16
AEC6X80: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    ide0: BM-DMA at 0x0180-0x0187, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0x0188-0x018f, BIOS settings: hdc:pio, hdd:pio
br-lan: port 1(eth0.0) entering learning state
br-lan: port 1(eth0.0) entering forwarding state
br-lan: topology change detected, propagating
Journalled Block Device driver loaded
hda: HDT722525DLAT80, ATA DISK drive
ide0 at 0x100-0x107,0x10a on irq 2
br-lan: port 1(eth0.0) entering disabled state
br-lan: port 1(eth0.0) entering learning state
br-lan: port 1(eth0.0) entering forwarding state
br-lan: topology change detected, propagating
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 488397168 sectors (250059 MB) w/7674KiB Cache, CHS=30401/255/63, UDMA(33)
Partition check:
 /dev/ide/host0/bus0/target0/lun0: unknown partition table
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (5953 buckets, 5953 max) - 352 bytes per conntrack
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
mini_fo: build_sto_structure: failed to create storage dir [1].
mini_fo: get_neg_sto_dentry: ERROR building sto structure.
ASSERTION FAILED: src != NULL at mini_fo.h:394 (fist_copy_attr_times)
Unable to handle kernel paging request at virtual address 00000000, epc == 80064830, ra == 80064830
Oops in fault.c::do_page_fault, line 206:
$0 : 00000000 1000fc00 00000049 83c24000 801928c0 00000001 00000001 801928d0
$8 : 00000000 00001f1d 00001f1d 00001ed4 801a0000 801a0000 801a0000 ffffffff
$16: 839e6440 00000000 ffffffff 83bab420 83bab420 839e6440 0040a6f0 004a98a4
$24: 00000002 00000002                   83a42000 83a43e90 0049eaec 80064830
Hi : 00000000
Lo : 00000000
epc   : 80064830    Not tainted
Status: 1000fc03
Cause : 0000000c
PrId  : 00029006
Process mv (pid: 680, stackpage=83a42000)
Stack:    839e6440 80155074 80155068 0000018a 8014b7d4 00000000 fffffff0
 83bab4b0 83babd80 83babe10 800461cc 839e6640 80044930 80044918 8004489c
 80044884 839e6440 81187000 839e6440 7fff7f92 00000000 00000000 0040a6f0
 800463e4 8115200e 00000015 3b3f7b79 00000010 839e6640 801ee520 8118700e
 00000015 3b3f7b79 00000010 00000000 00000000 00000001 0049eb90 7fff7e98
 80008aa0 ...
Call Trace:   [<80155074>] [<80155068>] [<8014b7d4>] [<800461cc>] [<80044930>]
 [<80044918>] [<8004489c>] [<80044884>] [<800463e4>] [<80008aa0>] [<8005bd8c>]

Code: 2407018a  0c004d79  afa20010 <a2200000> 8e220058  8e230050  8e240054  ae620058  ae630050
root@OpenWrt:/#

 --------------------------------------------------------------------------------------------------------

root@OpenWrt:/# mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro)
none on /dev type devfs (rw)
none on /proc type proc (rw)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev)
devpts on /dev/pts type devpts (rw)
root on /tmp/root type tmpfs (rw)
mini_fo:/tmp/root on /tmp/root type mini_fo (rw)
/dev/mtdblock/4 on /overlay type jffs2 (rw)
mini_fo:/overlay on / type mini_fo (rw)

 --------------------------------------------------------------------------------------------------------

root@OpenWrt:/# df -h
Filesystem                Size      Used Available Use% Mounted on
/dev/root                 1.1M      1.1M         0 100% /rom
tmpfs                    30.7M     36.0K     30.7M   0% /tmp
root                      1.1M      1.1M         0 100% /tmp/root
mini_fo:/tmp/root         1.1M      1.1M         0 100% /tmp/root
/dev/mtdblock/4          64.0K     64.0K         0 100% /overlay
mini_fo:/overlay          1.1M      1.1M         0 100% /
 --------------------------------------------------------------------------------------------------------

root@OpenWrt:/# opkg list-installed
base-files - 43.32-r29592
busybox - 1.15.3-3.4
dropbear - 0.53.1-5
e2fsprogs - 1.41.11-1
fdisk - 2.13.0.1-4
firewall - 2-34.8
iptables - 1.4.6-3.1
iptables-mod-conntrack - 1.4.6-3.1
iptables-mod-nat - 1.4.6-3.1
kernel - 2.4.37.9-1
kmod-diag - 2.4.37.9-7.1
kmod-fs-ext3 - 2.4.37.9-1
kmod-ide-aec62xx - 2.4.37.9-1
kmod-ide-core - 2.4.37.9-1
kmod-ipt-conntrack - 2.4.37.9-1
kmod-ipt-core - 2.4.37.9-1
kmod-ipt-nat - 2.4.37.9-1
kmod-switch - 2.4.37.9-4
libblkid - 1.41.11-1
libc - 0.9.30.1-43.32
libext2fs - 1.41.11-1
libgcc - 3.4.6-43.32
libip4tc - 1.4.6-3.1
libpthread - 0.9.30.1-43.32
librt - 0.9.30.1-43.32
libuci - 12012009.7-4
libuuid - 1.41.11-1
libxtables - 1.4.6-3.1
mtd - 13
nvram - 7
opkg - 576-2
uci - 12012009.7-4
 --------------------------------------------------------------------------------------------------------

root@OpenWrt:/# fdisk -l /dev/ide/host0/bus0/target0/lun0/disc
Disk /dev/ide/host0/bus0/target0/lun0/disc: 250.0 GB, 250059350016 bytes
255 heads, 63 sectors/track, 30401 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000000
Disk /dev/ide/host0/bus0/target0/lun0/disc doesn't contain a valid partition table


 --------------------------------------------------------------------------------------------------------
root@OpenWrt:/# fdisk /dev/ide/host0/bus0/target0/lun0/disc
Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel
Building a new DOS disklabel with disk identifier 0xacc7b6bf.
Changes will remain in memory only, until you decide to write them.
After that, of course, the previous content won't be recoverable.


The number of cylinders for this disk is set to 30401.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
   (e.g., DOS FDISK, OS/2 FDISK)
Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite)

Command (m for help):