API tools faq
paste
Advertisement
Guest User

K40 Laser Settings 24-7-17

a guest
Jul 24th, 2017
161
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 25.31 KB | None | 0 0
raw download clone embed print report
  1. # NOTE Lines must not exceed 132 characters
  2. ## Robot module configurations : general handling of movement G-codes and slicing into moves
  3. default_feed_rate 4000 # Default rate ( mm/minute ) for G1/G2/G3 moves
  4. default_seek_rate 4000 # Default rate ( mm/minute ) for G0 moves
  5. mm_per_arc_segment 0.0 # Fixed length for line segments that divide arcs 0 to disable
  6. mm_max_arc_error 0.01 # The maximum error for line segments that divide arcs 0 to disable
  7. # note it is invalid for both the above be 0
  8. # if both are used, will use largest segment length based on radius
  9. #mm_per_line_segment 5 # Lines can be cut into segments ( not usefull with cartesian
  10. # coordinates robots ).
  11.  
  12. # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
  13. alpha_steps_per_mm 157.575 # Steps per mm for alpha stepper
  14. beta_steps_per_mm 157.575 # Steps per mm for beta stepper
  15. gamma_steps_per_mm 1600 # Steps per mm for gamma stepper
  16.  
  17. # Planner module configuration : Look-ahead and acceleration configuration
  18. planner_queue_size 32 # DO NOT CHANGE THIS UNLESS YOU KNOW EXACTLY WHAT YOU ARE DOING
  19. acceleration 3000 # Acceleration in mm/second/second.
  20. #z_acceleration 500 # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA
  21. junction_deviation 0.05 # Similar to the old "max_jerk", in millimeters,
  22. # see https://github.com/grbl/grbl/blob/master/planner.c
  23. # and https://github.com/grbl/grbl/wiki/Configuring-Grbl-v0.8
  24. # Lower values mean being more careful, higher values means being
  25. # faster and have more jerk
  26. #z_junction_deviation 0.0 # for Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA
  27. #minimum_planner_speed 0.0 # sets the minimum planner speed in mm/sec
  28.  
  29. # Stepper module configuration
  30. microseconds_per_step_pulse 1 # Duration of step pulses to stepper drivers, in microseconds
  31. base_stepping_frequency 100000 # Base frequency for stepping
  32.  
  33. # Cartesian axis speed limits
  34. x_axis_max_speed 30000 # mm/min
  35. y_axis_max_speed 30000 # mm/min
  36. z_axis_max_speed 300 # mm/min
  37.  
  38. # Stepper module pins ( ports, and pin numbers, appending "!" to the number will invert a pin )
  39. alpha_step_pin 2.0 # Pin for alpha stepper step signal
  40. alpha_dir_pin 0.5! # Pin for alpha stepper direction
  41. alpha_en_pin 0.4 # Pin for alpha enable pin
  42. alpha_current 1.5 # X stepper motor current
  43. alpha_max_rate 30000.0 # mm/min
  44.  
  45. beta_step_pin 2.1 # Pin for beta stepper step signal
  46. beta_dir_pin 0.11! # Pin for beta stepper direction
  47. beta_en_pin 0.10 # Pin for beta enable
  48. beta_current 1.5 # Y stepper motor current
  49. beta_max_rate 30000.0 # mm/min
  50.  
  51. gamma_step_pin 2.2 # Pin for gamma stepper step signal
  52. gamma_dir_pin 0.20 # Pin for gamma stepper direction
  53. gamma_en_pin 0.19 # Pin for gamma enable
  54. gamma_current 1.5 # Z stepper motor current
  55. gamma_max_rate 300.0 # mm/min
  56.  
  57. ## System configuration
  58. # Serial communications configuration ( baud rate defaults to 9600 if undefined )
  59. uart0.baud_rate 115200 # Baud rate for the default hardware serial port
  60. second_usb_serial_enable false # This enables a second usb serial port (to have both pronterface
  61. # and a terminal connected)
  62. #leds_disable true # disable using leds after config loaded
  63. #play_led_disable true # disable the play led
  64.  
  65. # Kill button (used to be called pause) maybe assigned to a different pin, set to the onboard pin by default
  66. kill_button_enable true # set to true to enable a kill button
  67. kill_button_pin 2.12 # kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
  68.  
  69. #msd_disable false # disable the MSD (USB SDCARD) when set to true (needs special binary)
  70. #dfu_enable false # for linux developers, set to true to enable DFU
  71. #watchdog_timeout 10 # watchdog timeout in seconds, default is 10, set to 0 to disable the watchdog
  72.  
  73. # Only needed on a smoothieboard
  74. currentcontrol_module_enable true #
  75.  
  76. ## Extruder module configuration
  77. extruder.hotend.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
  78. extruder.hotend.steps_per_mm 140 # Steps per mm for extruder stepper
  79. extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  80. extruder.hotend.acceleration 500 # Acceleration for the stepper motor mm/sec²
  81. extruder.hotend.max_speed 50 # mm/s
  82.  
  83. extruder.hotend.step_pin 2.3 # Pin for extruder step signal
  84. extruder.hotend.dir_pin 0.22 # Pin for extruder dir signal
  85. extruder.hotend.en_pin 0.21 # Pin for extruder enable signal
  86.  
  87. # extruder offset
  88. #extruder.hotend.x_offset 0 # x offset from origin in mm
  89. #extruder.hotend.y_offset 0 # y offset from origin in mm
  90. #extruder.hotend.z_offset 0 # z offset from origin in mm
  91.  
  92. # firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
  93. #extruder.hotend.retract_length 3 # retract length in mm
  94. #extruder.hotend.retract_feedrate 45 # retract feedrate in mm/sec
  95. #extruder.hotend.retract_recover_length 0 # additional length for recover
  96. #extruder.hotend.retract_recover_feedrate 8 # recover feedrate in mm/sec (should be less than retract feedrate)
  97. #extruder.hotend.retract_zlift_length 0 # zlift on retract in mm, 0 disables
  98. #extruder.hotend.retract_zlift_feedrate 6000 # zlift feedrate in mm/min (Note mm/min NOT mm/sec)
  99.  
  100. delta_current 1.5 # First extruder stepper motor current
  101.  
  102. # Second extruder module configuration
  103. #extruder.hotend2.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
  104. #extruder.hotend2.steps_per_mm 140 # Steps per mm for extruder stepper
  105. #extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  106. #extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
  107. #extruder.hotend2.max_speed 50 # mm/s
  108.  
  109. #extruder.hotend2.step_pin 2.8 # Pin for extruder step signal
  110. #extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal
  111. #extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal
  112.  
  113. #extruder.hotend2.x_offset 0 # x offset from origin in mm
  114. #extruder.hotend2.y_offset 25.0 # y offset from origin in mm
  115. #extruder.hotend2.z_offset 0 # z offset from origin in mm
  116. #epsilon_current 1.5 # Second extruder stepper motor current
  117.  
  118.  
  119. ## Laser module configuration
  120. laser_module_enable true # Whether to activate the laser module at all. All configuration is
  121. # ignored if false.
  122. laser_module_pin 2.4! # this pin will be PWMed to control the laser. Only P2.0 - P2.5, P1.18, P1.20, P1.21, P1.23, P1.24, P1.26, P3.25, P3.26
  123. # can be used since laser requires hardware PWM
  124. laser_module_maximum_power 1.0 # this is the maximum duty cycle that will be applied to the laser
  125. laser_module_minimum_power 0.1 # This is a value just below the minimum duty cycle that keeps the laser
  126. # active without actually burning.
  127. #laser_module_default_power 1.0 # This is the default laser power that will be used for cuts if a power has not been specified. The value is a scale between
  128. # the maximum and minimum power levels specified above
  129. laser_module_pwm_period 100 # this sets the pwm frequency as the period in microseconds
  130.  
  131. switch.laserfire.enable true
  132. switch.laserfire.output_pin 2.5
  133. switch.laserfire.output_type digital
  134. switch.laserfire.input_on_command M3
  135. switch.laserfire.input_off_command M5
  136.  
  137. ## Temperature control configuration
  138. # First hotend configuration
  139. temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all.
  140. # All configuration is ignored if false.
  141. temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read
  142. temperature_control.hotend.heater_pin 2.7 # Pin that controls the heater, set to nc if a readonly thermistor is being defined
  143. temperature_control.hotend.thermistor EPCOS100K # see http://smoothieware.org/temperaturecontrol#toc5
  144. #temperature_control.hotend.beta 4066 # or set the beta value
  145. temperature_control.hotend.set_m_code 104 #
  146. temperature_control.hotend.set_and_wait_m_code 109 #
  147. temperature_control.hotend.designator T #
  148. #temperature_control.hotend.max_temp 300 # Set maximum temperature - Will prevent heating above 300 by default
  149. #temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below if set
  150.  
  151. # safety control is enabled by default and can be overidden here, the values show the defaults
  152. #temperature_control.hotend.runaway_heating_timeout 900 # max is 2040 seconds, how long it can take to heat up
  153. #temperature_control.hotend.runaway_cooling_timeout 900 # max is 2040 seconds, how long it can take to cool down if temp is set lower
  154. #temperature_control.hotend.runaway_range 20 # Max setting is 63°C
  155.  
  156. #temperature_control.hotend.p_factor 13.7 # permanently set the PID values after an auto pid
  157. #temperature_control.hotend.i_factor 0.097 #
  158. #temperature_control.hotend.d_factor 24 #
  159.  
  160. #temperature_control.hotend.max_pwm 64 # max pwm, 64 is a good value if driving a 12v resistor with 24v.
  161.  
  162. # Second hotend configuration
  163. #temperature_control.hotend2.enable true # Whether to activate this ( "hotend" ) module at all.
  164. # All configuration is ignored if false.
  165.  
  166. #temperature_control.hotend2.thermistor_pin 0.25 # Pin for the thermistor to read
  167. #temperature_control.hotend2.heater_pin 1.23 # Pin that controls the heater
  168. #temperature_control.hotend2.thermistor EPCOS100K # see http://smoothieware.org/temperaturecontrol#toc5
  169. ##temperature_control.hotend2.beta 4066 # or set the beta value
  170. #temperature_control.hotend2.set_m_code 104 #
  171. #temperature_control.hotend2.set_and_wait_m_code 109 #
  172. #temperature_control.hotend2.designator T1 #
  173.  
  174. #temperature_control.hotend2.p_factor 13.7 # permanently set the PID values after an auto pid
  175. #temperature_control.hotend2.i_factor 0.097 #
  176. #temperature_control.hotend2.d_factor 24 #
  177.  
  178. #temperature_control.hotend2.max_pwm 64 # max pwm, 64 is a good value if driving a 12v resistor with 24v.
  179.  
  180. temperature_control.bed.enable false #
  181. temperature_control.bed.thermistor_pin 0.24 #
  182. temperature_control.bed.heater_pin 2.5 #
  183. temperature_control.bed.thermistor Honeywell100K # see http://smoothieware.org/temperaturecontrol#toc5
  184. #temperature_control.bed.beta 3974 # or set the beta value
  185.  
  186. temperature_control.bed.set_m_code 140 #
  187. temperature_control.bed.set_and_wait_m_code 190 #
  188. temperature_control.bed.designator B #
  189.  
  190. #temperature_control.bed.bang_bang false # set to true to use bang bang control rather than PID
  191. #temperature_control.bed.hysteresis 2.0 # set to the temperature in degrees C to use as hysteresis
  192. # when using bang bang
  193.  
  194. ## Switch module for fan control
  195. switch.fan.enable false
  196. switch.fan.input_on_command M106 #
  197. switch.fan.input_off_command M107 #
  198. switch.fan.output_pin 2.6 #
  199. switch.fan.output_type pwm # pwm output settable with S parameter in the input_on_comand
  200. #switch.fan.max_pwm 255 # set max pwm for the pin default is 255
  201.  
  202. #switch.misc.enable true #
  203. #switch.misc.input_on_command M42 #
  204. #switch.misc.input_off_command M43 #
  205. #switch.misc.output_pin 2.4 #
  206. #switch.misc.output_type digital # just an on or off pin
  207.  
  208. # Switch module for spindle control
  209. #switch.spindle.enable false #
  210.  
  211. ## Temperatureswitch :
  212. # automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
  213. # useful to turn on a fan or water pump to cool the hotend
  214. #temperatureswitch.hotend.enable true #
  215. #temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor
  216. #temperatureswitch.hotend.switch misc # select which switch to use, matches the name of the defined switch
  217. #temperatureswitch.hotend.threshold_temp 60.0 # temperature to turn on (if rising) or off the switch
  218. #temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals
  219. #temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals
  220.  
  221.  
  222. ## Endstops
  223. endstops_enable true # the endstop module is enabled by default and can be disabled here
  224. #corexy_homing false # set to true if homing on a hbot or corexy
  225. alpha_min_endstop 1.24^ # add a ! to invert if endstop is NO connected to ground
  226. alpha_max_endstop 1.25^ # NOTE set to nc if this is not installed
  227. alpha_homing_direction home_to_min # or set to home_to_max and set alpha_max
  228. alpha_min 0 # this gets loaded after homing when home_to_min is set
  229. alpha_max 200 # this gets loaded after homing when home_to_max is set
  230. #beta_min_endstop 1.26^ #
  231. #beta_max_endstop 1.27^ #
  232. beta_max_endstop 1.26^ #
  233. beta_homing_direction home_to_max #
  234. beta_min 0 #
  235. beta_max 200 #
  236. gamma_min_endstop 1.28^ #
  237. gamma_max_endstop 1.29^ #
  238. gamma_homing_direction home_to_min #
  239. gamma_min 0 #
  240. gamma_max 200 #
  241.  
  242. alpha_max_travel 500 # max travel in mm for alpha/X axis when homing
  243. beta_max_travel 500 # max travel in mm for beta/Y axis when homing
  244. gamma_max_travel 500 # max travel in mm for gamma/Z axis when homing
  245.  
  246. # optional order in which axis will home, default is they all home at the same time,
  247. # if this is set it will force each axis to home one at a time in the specified order
  248. #homing_order XYZ # x axis followed by y then z last
  249. #move_to_origin_after_home false # move XY to 0,0 after homing
  250.  
  251. # optional enable limit switches, actions will stop if any enabled limit switch is triggered
  252. #alpha_limit_enable false # set to true to enable X min and max limit switches
  253. #beta_limit_enable false # set to true to enable Y min and max limit switches
  254. #gamma_limit_enable false # set to true to enable Z min and max limit switches
  255.  
  256. alpha_fast_homing_rate_mm_s 50 # feedrates in mm/second
  257. beta_fast_homing_rate_mm_s 50 # "
  258. gamma_fast_homing_rate_mm_s 4 # "
  259. alpha_slow_homing_rate_mm_s 25 # "
  260. beta_slow_homing_rate_mm_s 25 # "
  261. gamma_slow_homing_rate_mm_s 2 # "
  262.  
  263. alpha_homing_retract_mm 5 # distance in mm
  264. beta_homing_retract_mm 5 # "
  265. gamma_homing_retract_mm 1 # "
  266.  
  267. #endstop_debounce_count 100 # uncomment if you get noise on your endstops, default is 100
  268.  
  269. ## Z-probe
  270. zprobe.enable false # set to true to enable a zprobe
  271. zprobe.probe_pin 1.28!^ # pin probe is attached to if NC remove the !
  272. zprobe.slow_feedrate 5 # mm/sec probe feed rate
  273. #zprobe.debounce_count 100 # set if noisy
  274. zprobe.fast_feedrate 100 # move feedrate mm/sec
  275. zprobe.probe_height 5 # how much above bed to start probe
  276. #gamma_min_endstop nc # normally 1.28. Change to nc to prevent conflict,
  277.  
  278. # associated with zprobe the leveling strategy to use
  279. #leveling-strategy.three-point-leveling.enable true # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane
  280. #leveling-strategy.three-point-leveling.point1 100.0,0.0 # the first probe point (x,y) optional may be defined with M557
  281. #leveling-strategy.three-point-leveling.point2 200.0,200.0 # the second probe point (x,y)
  282. #leveling-strategy.three-point-leveling.point3 0.0,200.0 # the third probe point (x,y)
  283. #leveling-strategy.three-point-leveling.home_first true # home the XY axis before probing
  284. #leveling-strategy.three-point-leveling.tolerance 0.03 # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm
  285. #leveling-strategy.three-point-leveling.probe_offsets 0,0,0 # the probe offsets from nozzle, must be x,y,z, default is no offset
  286. #leveling-strategy.three-point-leveling.save_plane false # set to true to allow the bed plane to be saved with M500 default is false
  287.  
  288. ## Panel
  289. panel.enable true # set to true to enable the panel code
  290.  
  291. # Example for reprap discount GLCD
  292. # on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
  293. # +5v is EXP1 pin 10, Gnd is EXP1 pin 9
  294. panel.lcd reprap_discount_glcd #
  295. panel.spi_channel 0 # spi channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
  296. panel.spi_cs_pin 0.16 # spi chip select ; GLCD EXP1 Pin 4
  297. panel.encoder_a_pin 3.25!^ # encoder pin ; GLCD EXP2 Pin 3
  298. panel.encoder_b_pin 3.26!^ # encoder pin ; GLCD EXP2 Pin 5
  299. panel.click_button_pin 1.30!^ # click button ; GLCD EXP1 Pin 2
  300. panel.buzz_pin 0.27o # pin for buzzer ; GLCD EXP1 Pin 1
  301. panel.back_button_pin 2.11!^ # back button ; GLCD EXP2 Pin 8
  302.  
  303. panel.encoder_resolution 4
  304.  
  305. # pins used with other panels
  306. #panel.up_button_pin 0.1! # up button if used
  307. #panel.down_button_pin 0.0! # down button if used
  308. #panel.click_button_pin 0.18! # click button if used
  309.  
  310. panel.menu_offset 0 # some panels will need 1 here
  311.  
  312. panel.alpha_jog_feedrate 6000 # x jogging feedrate in mm/min
  313. panel.beta_jog_feedrate 6000 # y jogging feedrate in mm/min
  314. panel.gamma_jog_feedrate 200 # z jogging feedrate in mm/min
  315.  
  316. panel.hotend_temperature 185 # temp to set hotend when preheat is selected
  317. panel.bed_temperature 60 # temp to set bed when preheat is selected
  318.  
  319. ## Custom menus : Example of a custom menu entry, which will show up in the Custom entry.
  320. # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
  321. custom_menu.power_on.enable true #
  322. custom_menu.power_on.name Power_on #
  323. custom_menu.power_on.command M80 #
  324.  
  325. custom_menu.power_off.enable true #
  326. custom_menu.power_off.name Power_off #
  327. custom_menu.power_off.command M81 #
  328.  
  329.  
  330. ## Network settings
  331. network.enable false # enable the ethernet network services
  332. network.webserver.enable true # enable the webserver
  333. network.telnet.enable true # enable the telnet server
  334. network.ip_address auto # use dhcp to get ip address
  335. # uncomment the 3 below to manually setup ip address
  336. #network.ip_address 192.168.3.222 # the IP address
  337. #network.ip_mask 255.255.255.0 # the ip mask
  338. #network.ip_gateway 192.168.3.1 # the gateway address
  339. #network.mac_override xx.xx.xx.xx.xx.xx # override the mac address, only do this if you have a conflict
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!