..GXL:BL1:9ac50e:a1974b;FEAT:BDFD71BC;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 81919

BL2 Built : 13:27:37, Oct 25 2017. gxl g56b77aa - xiaobo.gu@droid12

_vcc5_power_init
rn5t567_power_init
Board ID = 1
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz
bist_test rank: 0 1a 05 2f 2d 1b 3f 17 00 2f 2b 16 40 19 04 2f 2a 12 42 17 00 2f 2d 16 45 693  rank: 1 1a 05 2f 2a 15 3f 15 00 2a 2c 15 43 14 04 24 2a 15 3f 14 01 27 2b 15 41 693   - PASS

Rank0: 1024MB(auto)-2T-13

Rank1: 1024MB(auto)-2T-13
AddrBus test pass!
-s
emmc switch 3 ok
Authentication key not yet programmed
emmc_rpmb_key_is_programmed: error 0x00000007
emmc switch 0 ok
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
aml log : R1024 check pass!
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01700000, size: 0x0000d600
aml log : R1024 check pass!
Load bl31 from eMMC, src: 0x00020200, des: 0x01700000, size: 0x0002c600
aml log : R1024 check pass!
Load bl32 from eMMC, src: 0x00050200, des: 0x01700000, size: 0x00034600
aml log : R1024 check pass!
Load bl33 from eMMC, src: 0x00088200, des: 0x01700000, size: 0x00051e00
aml log : R1024 check pass!
NOTICE:  BL3-1: v1.0(release):7c45a4f
NOTICE:  BL3-1: Built : 14:09:28, Oct 13 2017
[BL31]: GXL CPU setup!
NOTICE:  BL31: GXL secure boot!
NOTICE:  BL31: BL33 decompress pass
mpu_config_enable:ok

[Image: gxl_v1.1.3255-1a77b01 2017-09-15 16:58:02 xiaobo.gu@droid12]

OPS=0x82

b9 cf 79 bf 8d 20 e4 51 cc ef 4f 6e [1.447867 Inits done]

secure task start!
high task start!
low task start!
INFO:    BL3-2: ATOS-V2.4-67-g26d2f32 #1 Tue Jan 23 10:10:32 UTC 2018 arm
INFO:    BL3-2: Chip: GXL Rev: B (21:B - 80:2)
INFO:    BL3-2: crypto engine DMA
INFO:    BL3-2: secure time TEE
INFO:    BL3-2: CONFIG_DEVICE_SECURE 0xb200000e


U-Boot 2015.01-g0a1e56b (Jun 21 2018 - 13:51:11), Build: jenkins-once_cts-2167

DRAM:  2 GiB
Relocation Offset is: 76edb000
register usb cfg[0][1] = 0000000077f65290
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpu: vpu_clk_gate_init_off
MMC:   aml_priv->desc_buf = 0x0000000073edb640
aml_priv->desc_buf = 0x0000000073edd960
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
original ext_csd[171] USE_WP field value is 50
ext_csd[171] USER_WP filed value after switch is 58
[mmc_init] mmc init success
aml log : R1024 check pass!
      Amlogic multi-dtb tool
      Single dtb detected
start dts,buffer=0000000073ee01b0,dt_addr=0000000073ee01b0
      Amlogic multi-dtb tool
      Single dtb detected
parts: 16
00:     cache.0000000010000000 2
01:      logo.0000000000300000 1
02:   encrypt.0000000000100000 1
03:  recovery.0000000002000000 1
04:       tee.0000000000800000 1
05:     crypt.0000000002000000 1
06:      misc.0000000002000000 1
07:      boot.0000000001400000 1
08:       dto.0000000000800000 1
09:  cri_data.0000000000800000 2
10:     param.0000000001000000 2
11:       rsv.0000000001000000 1
12:    system.0000000044c00000 1
13:       oem.0000000012c00000 1
14:    vendor.0000000006400000 1
15:      data.ffffffffffffffff 4
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x10c00000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
hpd_state=0
cvbs performance type = 6, table = 0
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-1078: calc 1613cf46, store 1613cf46
_verify_dtb_checksum()-1078: calc 1613cf46, store 1613cf46
dtb_read()-1200: total valid 2
dtb_read()-1267: do nothing
aml log : R1024 check pass!
      Amlogic multi-dtb tool
      Single dtb detected
hpd_state=0
cvbs performance type = 6, table = 0
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[carrier] not programed yet
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f800000
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=5760, height=2160
pull down bt_reset
pull up bt_reset
set hci reset
04 0e 04 01 03 0c 00
set scan parameters
04 0e 04 01 0b 20 00
set scan enable
04 0e 04 01 0c 20 00
pull down bt_enable
once#

once#