Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- uloader 2011.06.0 (May 20 2014 - 16:36:41)
- Board: Mindspeed C2000
- c2k_spi_probe
- Copying Barebox from SPI Flash(bootopt=0)
- BB Copying Done
- ## Starting Barebox at 0x01000000 ...
- barebox 2011.06.0-svn44305-dirty6 (Aug 28 2014 - 22:25:22)
- Board: Mindspeed C2000
- c2k_spi_probe
- c2k_otp_probe.
- cbus_baseaddr: 9c000000, ddr_baseaddr: 03800000, ddr_phys_baseaddr: 03800000
- class init complete
- tmu init complete
- bmu1 init: done
- bmu2 init: done
- util init complete
- GPI1 init complete
- GPI2 init complete
- HGPI init complete
- HIF rx desc: base_va: 03e80000, base_pa: 03e80000
- HIF tx desc: base_va: 03e80400, base_pa: 03e80400
- HIF init complete
- bmu1 enabled
- bmu2 enabled
- pfe_hw_init: done
- pfe_firmware_init
- pfe_load_elf
- pfe_load_elf no of sections: 10
- pfe_firmware_init: class firmware loaded
- pfe_load_elf
- pfe_load_elf no of sections: 10
- pfe_firmware_init: tmu firmware loaded
- pfe_load_elf
- pfe_load_elf no of sections: 14
- pfe_firmware_init: util firmware loaded
- eth_port: 0
- NAS540_phy_reg_setting[eth_port].phyaddr: 0x4
- miidev_restart_aneg for PHY4
- eth_port: 1
- NAS540_phy_reg_setting[eth_port].phyaddr: 0x6
- miidev_restart_aneg for PHY6
- cfi_probe: cfi_flash base: 0xc0000000 size: 0x04000000
- ## Unknown FLASH on Bank at 0xc0000000 - Size = 0x00000000 = 0 MB
- bootopt = 0x0
- Using ENV from SPI Flash.
- nand_probe: comcerto_nand base: 0xc8300000 size: 0x256 MB
- NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD NAND 256MiB 3,3V 8-bit), page size: 2048, OOB size: 64
- Using default values
- Bad block table not found for chip 0
- Bad block table not found for chip 0
- Scanning device for bad blocks
- Bad block table written to 0x0ffe0000, version 0x01
- Bad block table written to 0x0ffc0000, version 0x01
- Malloc space: 0x00600000 -> 0x01000000 (size 10 MB)
- Stack space : 0x005f8000 -> 0x00600000 (size 32 kB)
- running /env/bin/init...
- Unknown command 'export' - try 'help'
- Disabling eee function of phy 4 ...
- Disabling eee function of phy 6 ...
- Hit any key to stop autoboot: 0
- booting kernel of type uimage from /dev/nand0.kernel2.bb
- Verifying Checksum ... OK
- Image Name: Linux-3.2.54
- Created: 2018-05-21 17:36:47 UTC
- Image Type: <NULL> <NULL> <NULL> (<NULL>)
- Data Size: 7311656 Bytes = 7 MB
- Load Address: 0f008000
- Entry Point: 0f008000
- OK
- Starting kernel ...
- commandline: console=ttyS0,115200n8, init=/etc/preinit pcie_gen1_only=yes mac_addr=,, ip=dhcp root=ubi0:rootfs ubi.mtd=2,2048 rootfstype=ubifs rw noinitrd mtdparts=spi0.0:256k(uloader)ro,512k(barebox)ro,256k(env);comcertonand:10M(config),10M(kernel1),110M(rootfs1),10M(kernel2),110M(rootfs2),-(reserved) usb3_internal_clk=yes
- arch_number: 1094
- Uncompressing Linux... done, booting the kernel.
- [ 0.000000] Booting Linux on physical CPU 0
- [ 0.000000] Initializing cgroup subsys cpuset
- [ 0.000000] Linux version 3.2.54 (root@SDD2SVR2) (gcc version 4.8.5 20150209 (prerelease) (crosstool-NG 1.21.0) ) #1 SMP Tue May 22 01:36:44 CST 2018
- [ 0.000000] CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=50c53c7d
- [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000] Machine: Comcerto 2000 EVM
- [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
- [ 0.000000] Comcerto: zone_dma mapping size=2c00000 type=b
- [ 0.000000] PERCPU: Embedded 8 pages/cpu @8524c000 s9504 r8192 d15072 u32768
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 254976
- [ 0.000000] Kernel command line: console=ttyS0,115200n8, init=/etc/preinit pcie_gen1_only=yes mac_addr=,, ip=dhcp root=ubi0:rootfs ubi.mtd=2,2048 rootfstype=ubifs rw noinitrd mtdparts=spi0.0:256k(uloader)ro,512k(barebox)ro,256k(env);comcertonand:10M(config),10M(kernel1),110M(rootfs1),10M(kernel2),110M(rootfs2),-(reserved) usb3_internal_clk=yes
- [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
- [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000] Memory: 44MB 960MB = 1004MB total
- [ 0.000000] Memory: 1008508k/1008508k available, 40068k reserved, 0K highmem
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000] fixmap : 0xfff30000 - 0xfffe0000 ( 704 kB)
- [ 0.000000] vmalloc : 0xc0800000 - 0xf0000000 ( 760 MB)
- [ 0.000000] lowmem : 0x80000000 - 0xc0000000 (1024 MB)
- [ 0.000000] modules : 0x83600000 - 0x84000000 ( 10 MB)
- [ 0.000000] .text : 0x84008000 - 0x8468b460 (6670 kB)
- [ 0.000000] .init : 0x8468c000 - 0x8499a520 (3130 kB)
- [ 0.000000] .data : 0x8499c000 - 0x849e4bb0 ( 291 kB)
- [ 0.000000] .bss : 0x849e4bd4 - 0x84a45218 ( 386 kB)
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] NR_IRQS:256
- [ 0.000000] PLL0 running at 2400 MHz, PLL1 at 1000 MHz PLL2 running at 1500 MHz PLL3 running at 1066 MHz
- [ 0.000000] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 17179ms
- [ 0.000194] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
- [ 0.090047] pid_max: default: 32768 minimum: 301
- [ 0.090244] Mount-cache hash table entries: 512
- [ 0.090770] Initializing cgroup subsys cpuacct
- [ 0.090802] Initializing cgroup subsys devices
- [ 0.090838] CPU: Testing write buffer coherency: ok
- [ 0.091001] CPU0: thread -1, cpu 0, socket 9, mpidr 80000900
- [ 0.091029] Calibrating local timer... 299.83MHz.
- [ 0.150069] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
- [ 0.151164] CPU1 powered up
- [ 0.151763] CPU1: Booted secondary processor
- [ 0.190037] CPU1: thread -1, cpu 1, socket 9, mpidr 80000901
- [ 0.190093] Brought up 2 CPUs
- [ 0.190105] SMP: Total of 2 processors activated (2393.70 BogoMIPS).
- [ 0.191622] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 2
- [ 0.192010] xor: measuring software checksum speed
- [ 0.239986] arm4regs : 2129.600 MB/sec
- [ 0.289955] 8regs : 1397.600 MB/sec
- [ 0.339927] 32regs : 1186.000 MB/sec
- [ 0.389910] neon : 1383.600 MB/sec
- [ 0.389917] xor: using function: arm4regs (2129.600 MB/sec)
- [ 0.390101] NET: Registered protocol family 16
- [ 0.391839] L310 cache controller enabled
- [ 0.391852] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x00c40000, PREFETCH_CTRL 0x00000000, Cache size: 262144 B
- [ 0.391932] ARMv7 AUX CTRL(0): 0x41
- [ 0.391937] ARMv7 AUX CTRL(0): 0x41
- [ 0.391954] ARMv7 AUX CTRL(1): 0x41
- [ 0.391962] ARMv7 AUX CTRL(1): 0x41
- [ 0.392879] Pin Select for GPIO[15:0]: 05000000
- [ 0.392886] Pin Select for GPIO[31:16]: 00555540
- [ 0.392891] Output Enable for GPIO[31:0]: DFFFFF00
- [ 0.392897] Pin Select for GPIO[59:32]: 0FFFFFFE
- [ 0.392902] Pin Select for GPIO[63:60]: 00000020
- [ 0.392908] Output Enable for GPIO[63:32]: 00000001
- [ 0.392914] Enable USB ...
- [ 0.394195] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
- [ 0.394205] hw-breakpoint: maximum watchpoint size is 4 bytes.
- [ 0.394220] Power Management Mode Support For C2000:
- [ 0.394588] PCIe: Ref clk 48Mhz
- [ 0.394595] PCIe: Detected C2K RevA1 device serdes clk devider old:new=2e:6
- [ 0.411540] PCIe0: Link Up Success
- [ 0.411546] PCIe0: Polarity: 0 Gen1 mode: 1 External Clk: 0
- [ 0.411552] comcerto_pcie_rc_int_init
- [ 0.411955] PCI: bus0: Fast back to back transfers disabled
- [ 0.412133] pci 0000:00:00.0: BAR 6: assigned [mem 0xa0000000-0xa000ffff pref]
- [ 0.412144] pci 0000:00:00.0: BAR 5: assigned [mem 0xa0010000-0xa00101ff]
- [ 0.412157] pci 0000:00:00.0: BAR 5: set to [mem 0xa0010000-0xa00101ff] (PCI address [0xa0010000-0xa00101ff])
- [ 0.438889] bio: create slab <bio-0> at 0
- [ 0.601116] raid6: int32x1 32 MB/s
- [ 0.770445] raid6: int32x2 49 MB/s
- [ 0.940075] raid6: int32x4 84 MB/s
- [ 1.109923] raid6: int32x8 119 MB/s
- [ 1.279731] raid6: neonx1 144 MB/s
- [ 1.449494] raid6: neonx2 177 MB/s
- [ 1.619460] raid6: neonx4 199 MB/s
- [ 1.789374] raid6: neonx8 201 MB/s
- [ 1.789380] raid6: using algorithm neonx8 (201 MB/s)
- [ 1.789672] vgaarb: loaded
- [ 1.790222] SCSI subsystem initialized
- [ 1.791110] usbcore: registered new interface driver usbfs
- [ 1.791340] usbcore: registered new interface driver hub
- [ 1.791494] usbcore: registered new device driver usb
- [ 1.792519] Switching to clocksource timer2
- [ 1.802199] NET: Registered protocol family 2
- [ 1.802416] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 1.803201] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
- [ 1.804556] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
- [ 1.805171] TCP: Hash tables configured (established 131072 bind 65536)
- [ 1.805179] TCP reno registered
- [ 1.805191] UDP hash table entries: 512 (order: 2, 16384 bytes)
- [ 1.805246] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
- [ 1.805607] NET: Registered protocol family 1
- [ 1.805913] RPC: Registered named UNIX socket transport module.
- [ 1.805921] RPC: Registered udp transport module.
- [ 1.805926] RPC: Registered tcp transport module.
- [ 1.805932] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 2.035162] gpio_dev = fd00000
- [ 2.035431] membuf_init: created membuf device(252, 0)
- [ 2.035498] clock_frequency_set: (1:24) NTG INCR value is 422212465
- [ 2.067427] VFS: Disk quotas dquot_6.5.2
- [ 2.067585] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [ 2.068271] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
- [ 2.068280] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
- [ 2.068870] fuse init (API version 7.17)
- [ 2.070976] Btrfs loaded
- [ 2.071007] msgmni has been set to 1969
- [ 2.076708] async_tx: api initialized (async)
- [ 2.077146] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
- [ 2.077159] io scheduler noop registered
- [ 2.077165] io scheduler deadline registered
- [ 2.077270] io scheduler cfq registered (default)
- [ 2.083215] ### comcerto_dma_probe: XOR DMA channel registered
- [ 2.087333] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
- [ 2.262960] 84a386a0 849af858 0 ffffffff
- [ 2.263914] serial8250 serial8250.0: Couldn't set LCR to 191
- [ 2.265432] serial8250 serial8250.0: Couldn't set LCR to 191
- [ 2.267390] serial8250 serial8250.0: Couldn't set LCR to 224
- [ 2.268666] serial8250 serial8250.0: Couldn't set LCR to 224
- [ 2.288705] serial8250.0: ttyS0 at MMIO 0x96400000 (irq = 59) is a 16550A
- [ 2.995205] console [ttyS0] enabled
- [ 3.028283] comcerto_otp_probe.
- [ 3.081457] loop: module loaded
- [ 3.095489] PCI: enabling device 0000:00:00.0 (0140 -> 0142)
- [ 3.101269] ahci: SSS flag set, parallel bus scan disabled
- [ 3.106848] ahci 0000:00:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
- [ 3.114985] ahci 0000:00:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs
- [ 3.142109] scsi0 : ahci
- [ 3.151213] scsi1 : ahci
- [ 3.154790] ata1: SATA max UDMA/133 abar m512@0xa0010000 port 0xa0010100 irq 96
- [ 3.162131] ata2: SATA max UDMA/133 abar m512@0xa0010000 port 0xa0010180 irq 96
- [ 3.174559] SATA Serdes: 48Mhz ref clk
- [ 3.178809] Serdes1: Lane OK Passed
- [ 3.182788] Serdes2: Lane OK Passed
- [ 3.186291] ahci ahci: forcing PORTS_IMPL to 0x3
- [ 3.190981] ahci ahci: AHCI 0001.0300 32 slots 2 ports 3 Gbps 0x3 impl platform mode
- [ 3.198762] ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
- [ 3.219478] scsi2 : ahci_platform
- [ 3.231772] scsi3 : ahci_platform
- [ 3.236057] ata3: SATA max UDMA/133 mmio [mem 0x9d000000-0x9d00ffff] port 0x100 irq 48
- [ 3.244048] ata4: SATA max UDMA/133 mmio [mem 0x9d000000-0x9d00ffff] port 0x180 irq 48
- [ 3.256742] designware_spi_probe:Initializing SPI Controller : Using dma=0 CLK(DUS)=250000000 Hz
- [ 3.269715] comcerto_spi comcerto_spi.1: at 0x96500000 mapped to 0xC080A000, irq=60
- [ 3.277450] designware_spi_probe:Initializing SPI Controller : Using dma=0 CLK(spi_i2c)=250000000 Hz
- [ 3.295207] comcerto_spi comcerto_spi.0: at 0x90498000 mapped to 0xC080C000, irq=61
- [ 3.328269] comcertoflash: probe of comcertoflash.0 failed with error -5
- [ 3.335432] m25p80 spi0.0: found mx25l8005, expected s25fl256s0
- [ 3.341377] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
- [ 3.346239] 3 cmdlinepart partitions found on MTD device spi0.0
- [ 3.352175] Creating 3 MTD partitions on "spi0.0":
- [ 3.357002] 0x000000000000-0x000000040000 : "uloader"
- [ 3.368336] 0x000000040000-0x0000000c0000 : "barebox"
- [ 3.385197] 0x0000000c0000-0x000000100000 : "env"
- [ 3.401374] pdev->resource->start = c8300000, pdev->resource->end = c8301fff
- [ 3.408503] nand_probe: comcertonand base: 0xc0800000
- [ 3.413687] ONFI flash detected
- [ 3.416915] ONFI param page 0 valid
- [ 3.420415] NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD S34ML02G1)
- [ 3.427585] hw_syndrome correction 2048.
- [ 3.431516] Using default values for hw ecc
- [ 3.439014] Bad block table not found for chip 0
- [ 3.446892] Bad block table not found for chip 0
- [ 3.451520] Scanning device for bad blocks
- [ 3.502588] ata1: SATA link down (SStatus 0 SControl 320)
- [ 3.533229] Bad block table written to 0x00000ffe0000, version 0x01
- [ 3.541343] Bad block table written to 0x00000ffc0000, version 0x01
- [ 3.547683] 6 cmdlinepart partitions found on MTD device comcertonand
- [ 3.554157] Creating 6 MTD partitions on "comcertonand":
- [ 3.559487] 0x000000000000-0x000000a00000 : "config"
- [ 3.570999] 0x000000a00000-0x000001400000 : "kernel1"
- [ 3.587767] 0x000001400000-0x000008200000 : "rootfs1"
- [ 3.593049] ata3: SATA link down (SStatus 0 SControl 320)
- [ 3.602624] ata4: SATA link down (SStatus 0 SControl 320)
- [ 3.610731] 0x000008200000-0x000008c00000 : "kernel2"
- [ 3.627959] 0x000008c00000-0x00000fa00000 : "rootfs2"
- [ 3.639540] 0x00000fa00000-0x000010000000 : "reserved"
- [ 3.669331] Fixed MDIO Bus: probed
- [ 3.673494] ## xhci_plat_probe
- [ 3.676567] ### comcerto_start_xhci
- [ 3.680083] USB3.0 clock selected: internal
- [ 3.687547] xhci-hcd xhci-hcd: xHCI Host Controller
- [ 3.692571] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
- [ 3.699796] xhci-hcd xhci-hcd: irq 54, io mem 0x9f000000
- [ 3.705209] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- [ 3.712017] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 3.719288] usb usb1: Product: xHCI Host Controller
- [ 3.724199] usb usb1: Manufacturer: Linux 3.2.54 xhci-hcd
- [ 3.729613] usb usb1: SerialNumber: xhci-hcd
- [ 3.738436] hub 1-0:1.0: USB hub found
- [ 3.742220] hub 1-0:1.0: 1 port detected
- [ 3.752296] xhci-hcd xhci-hcd: xHCI Host Controller
- hotplug394add:
- [ 3.757274] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
- [ 3.765784] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
- [ 3.772632] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 3.779884] usb usb2: Product: xHCI Host Controller
- [ 3.784803] usb usb2: Manufacturer: Linux 3.2.54 xhci-hcd
- [ 3.790217] usb usb2: SerialNumber: xhci-hcd
- hotplug395add:9
- [ 3.799982] hub 2-0:1.0: USB hub found
- [ 3.803818] hub 2-0:1.0: 1 port detected
- [ 3.821104] usbcore: registered new interface driver usblp
- hotplug395add:[9[ 3.826689] Initializing USB Mass Storage driver...
- /0/0]USB hub dev[ 3.833857] usbcore: registered new interface driver usb-storage
- [ 3.840332] USB Mass Storage support registered.
- [ 3.846369] dwc_otg: version 2.94a 27-OCT-2011
- [ 3.856119] ata2: SATA link down (SStatus 0 SControl 320)
- hotplug398add:9
- hotplug398add:[9/0/0]USB hub device:09h/xxh/xxh
- [ 4.050876] Core Release: 2.81a
- [ 4.054043] Setting default values for core params
- [ 4.062586] usb 1-1: new high-speed USB device number 2 using xhci-hcd
- [ 4.108605] usb 1-1: New USB device found, idVendor=174c, idProduct=2074
- [ 4.115335] usb 1-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
- [ 4.122490] usb 1-1: Product: ASM107x
- [ 4.126165] usb 1-1: Manufacturer: Asmedia
- [ 4.130272] usb 1-1: SerialNumber: 0000000A0003
- hotplug403add:[ 4.152056] hub 1-1:1.0: USB hub found
- [ 4.156316] hub 1-1:1.0: 4 ports detected
- hotplug404add:[9/0/1]USB hub device:09h/xxh/xxh
- [ 4.258755] Using Buffer DMA mode
- [ 4.262083] Periodic Transfer Interrupt Enhancement - disabled
- [ 4.267936] Multiprocessor Interrupt Enhancement - disabled
- [ 4.273529] OTG VER PARAM: 0, OTG VER FLAG: 0
- [ 4.277936] dwc_otg dwc_otg.0: DWC OTG Controller
- [ 4.282700] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 3
- [ 4.289788] dwc_otg dwc_otg.0: irq 53, io mem 0x00000000
- [ 4.295189] Init: Port Power? op_state=1
- [ 4.299122] Init: Power Port (0)
- [ 4.302413] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
- [ 4.309231] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 4.316479] usb usb3: Product: DWC OTG Controller
- [ 4.321196] usb usb3: Manufacturer: Linux 3.2.54 dwc_otg
- [ 4.326527] usb usb3: SerialNumber: dwc_otg.0
- [ 4.332142] hub 3-0:1.0: USB hub found
- [ 4.335998] hub 3-0:1.0: 1 port detected
- hotplug406add:
- [ 4.366900] mousedev: PS/2 mouse device common for all mice
- hotplug407add:9
- [ 4.380208] c2k-rtc c2k-rtc: rtc core: registered c2k as rtc0
- [ 4.386023] C2000 RTC, (c) 2012 Mindspeed Technologies
- [ 4.391298] c2k-rtc c2k-rtc: Warning: Invalid RTC value so initializing it
- [ 4.403113] i2c /dev entries driver
- hotplug407add:[9/0/0]USB hub dev[ 4.409077] comcerto_i2c_calculate_dividers: speed=97kHz, M=1, N=7, dividers=0x0f
- ice:09h/xxh/xxh
- [ 4.423598] i2c-core: driver [eeprom] using legacy suspend method
- [ 4.429713] i2c-core: driver [eeprom] using legacy resume method
- [ 4.438147] comcerto_wdt: support registered
- [ 4.442972] md: linear personality registered for level -1
- [ 4.443578] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
- [ 4.455059] md: raid0 personality registered for level 0
- [ 4.460386] md: raid1 personality registered for level 1
- [ 4.465730] md: raid10 personality registered for level 10
- [ 4.471230] md: raid6 personality registered for level 6
- [ 4.474994] usb 2-1: New USB device found, idVendor=174c, idProduct=3074
- [ 4.475001] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
- [ 4.475007] usb 2-1: Product: ASM107x
- [ 4.475012] usb 2-1: Manufacturer: Asmedia
- [ 4.475016] usb 2-1: SerialNumber: 0000000A0003
- [ 4.502777] md: raid5 personality registered for level 5
- [pv[ 4.509148] hub 2-1:1.0: USB hub found
- [ 4.513026] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
- [ 4.513177] hub 2-1:1.0: 4 ports detected
- hotplug423add:
- hotplug424add:9
- hotplug424add:[9/0/0]USB hub device:09h/xxh/xxh
- [ 4.595331] usbcore: registered new interface driver usbhid
- [ 4.600927] usbhid: USB HID core driver
- [ 4.605563] etherip: Ethernet over IPv4 tunneling driver
- [ 4.610891] etherip ----- is functional
- [ 4.620940] TCP cubic registered
- [ 4.624648] NET: Registered protocol family 10
- [ 4.631578] IPv6 over IPv4 tunneling driver
- [ 4.632685] usb 1-1.3: new high-speed USB device number 3 using xhci-hcd
- [ 4.645791] usb 1-1.3: New USB device found, idVendor=054c, idProduct=0243
- [ 4.652735] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
- [ 4.660073] usb 1-1.3: Product: Storage Media
- [ 4.664478] usb 1-1.3: Manufacturer: Sony
- [ 4.668503] usb 1-1.3: SerialNumber: 1505112125225
- [ 4.668873] NET: Registered protocol family 17
- [ 4.677805] 8021q: 802.1Q VLAN Support v1.8
- [ 4.682043] Registering the dns_resolver key type
- [ 4.684220] usb 1-1.3: ep 0x81 - rounding interval to 128 microframes, ep desc says 255 microframes
- [ 4.684234] usb 1-1.3: ep 0x2 - rounding interval to 128 microframes, ep desc says 255 microframes
- [d[ 4.705109] Clocks: disabled unused gemtx
- [ 4.709130] Clocks: disabled unused ipsec_spacc
- [ 4.713722] Clocks: disabled unused dpi_cie
- hotplug451add:[ 4.717935] Clocks: disabled unused dpi_decomp
- [ 4.717943] Clocks: disabled unused pcie1
- [ 4.717949] Clocks: disabled unused ext_phy0
- [ 4.717954] Clocks: disabled unused ext_phy1
- [ 4.717958] Clocks: disabled unused ext_phy2
- [ 4.717962] Clocks: disabled unused tpi
- [ 4.717966] Clocks: disabled unused csys
- [ 4.717970] Clocks: disabled unused tsuntg
- [ 4.717974] Clocks: disabled unused sata_occ
- [ 4.717978] Clocks: disabled unused pcie_occ
- [ 4.717982] Clocks: disabled unused sgmii_occ
- [ 4.771445] UBI: attaching mtd2 to ubi0
- [ 4.771453] scsi4 : usb-storage 1-1.3:1.0
- hotplug452add:8
- [ 4.783143] UBI: scanning is finished
- [ 4.786827] UBI error: ubi_read_volume_table: the layout volume was not found
- [ 4.794036] UBI error: ubi_attach_mtd_dev: failed to attach mtd2, error -22
- [ 4.801042] UBI error: ubi_init: cannot attach mtd2
- [ 4.806083] c2k-rtc c2k-rtc: setting system clock to 2012-07-12 18:25:01 UTC (1342117501)
- [ 4.820539] Freeing init memory: 3128K
- *** Stage 1: Setup system and device drivers ***
- Fail to open gpio device
- [ 5.803765] scsi 4:0:0:0: Direct-Access Sony Storage Media 0100 PQ: 0 ANSI: 0 CCS
- [ 5.826224] sd 4:0:0:0: [sda] 2030592 512-byte logical blocks: (1.03 GB/991 MiB)
- [ 5.835343] sd 4:0:0:0: [sda] Write Protect is off
- [ 5.836014] sd 4:0:0:0: Attached scsi generic sg0 type 0
- [ 5.846539] sd 4:0:0:0: [sda] No Caching mode page found
- [ 5.851877] sd 4:0:0:0: [sda] Assuming drive cache: write through
- [ 5.862329] sd 4:0:0:0: [sda] No Caching mode page found
- [ 5.867697] sd 4:0:0:0: [sda] Assuming drive cache: write through
- [ 5.952879] sda: sda1
- hotplug468add:[/block/sda][sda]Mass Storage device
- [ 6.002815] sd 4:0:0:0: [sda] No Caching mode page found
- [ 6.008155] sd 4:0:0:0: [sda] Assuming drive cache: write through
- [ 6.014300] sd 4:0:0:0: [sda] Attached SCSI removable disk
- [ 6.832562] pfe_module_init
- [ 6.835421] pfe_platform_probe
- [ 6.839674] ipsec: baseaddr :9a000000 --- c0a00000
- [ 6.845526] pfe_probe
- [ 6.847805] PFE Driver version:
- [ 6.847807] pfe_ctrl_12_00_2
- [ 6.847809] built with pfe sources version: pfe_12_00_2
- [ 6.859093] cbus_baseaddr: c3000000, ddr_baseaddr: c2000000, ddr_phys_baseaddr: 3400000, ddr_size: c00000
- [ 6.868701] pfe_hw_init
- [ 6.871153] CLASS version: 20
- [ 6.874147] TMU version: 1011231
- [ 6.877382] BMU1 version: 21
- [ 6.880267] BMU2 version: 21
- [ 6.883170] EMAC1 network cfg: 80000
- [ 6.886753] EMAC2 network cfg: 80000
- [ 6.890336] EMAC3 network cfg: 80000
- [ 6.893931] EGPI1 version: 50
- [ 6.896905] EGPI2 version: 50
- [ 6.899879] EGPI3 version: 50
- [ 6.902859] HGPI version: 50
- [ 6.905745] GPT version: 0
- [ 6.908458] HIF version: 10
- [ 6.911257] HIF NOPCY version: 10
- [ 6.914585] UTIL version: 20
- [ 6.917472] bmu_init(1) done
- [ 6.920359] bmu_init(2) done
- [ 6.929874] class_init() done
- [ 6.932861] tmu_init: mem init
- [ 6.935923] tmu_init: lmem init
- [ 6.939112] tmu_init() done
- [ 6.941911] util_init() done
- [ 6.944805] gpi_init(1) done
- [ 6.947693] gpi_init(2) done
- [ 6.950580] gpi_init(3) done
- [ 6.953476] gpi_init(hif) done
- [ 6.956537] bmu_enable(1) done
- [ 6.959597] bmu_enable(2) done
- [ 6.962664] pfe_hif_lib_init
- [ 6.965753] pfe_hif_init
- [ 6.968292] pfe_hif_alloc_descr
- [ 6.971643] pfe_hif_init_buffers
- [ 6.975029] pfe_firmware_init
- [ 6.996793] pfe_load_elf
- [ 6.999354] pe_load_ddr_section: load address(3fb0000) and elf file address(c083b000) rcvd
- [ 7.031375] PFE binary version: pfe_12_00_2
- [ 7.035599] pfe_firmware_init: class firmware loaded 0xb20 0xc3010000
- [ 7.042057] pfe_load_elf
- [ 7.045973] pfe_firmware_init: tmu firmware loaded 0x220
- [ 7.051300] pfe_load_elf
- [ 7.055756] pfe_firmware_init: util firmware loaded 0x16c0
- [ 7.061287] pfe_ctrl_init
- [ 7.083442] pfe_ctrl_init finished
- [ 7.086854] pfe_eth_init
- [ 7.090305] pfe_ctrl_timer
- [ 7.102955] Comcerto MDIO Bus: probed
- [ 7.208961] eth0: pfe_eth_init_one: created interface, baseaddr: c3200000
- [ 7.315404] eth1: pfe_eth_init_one: created interface, baseaddr: c3220000
- [ 7.322232] pfe_vwd_init
- [ 7.324989] pfe_vwd_init: created vwd device(250, 0)
- [ 7.329969] pfe_vwd_driver_init: start
- [ 7.333751] pfe_vwd_up: start
- [ 7.336759] comcerto_wifi_rx_fastpath_register:33 VWD Tx function registered
- [ 7.343860] pfe_vwd_driver_init: end
- [ 7.347449] pfe_pcap_init
- crw-rw---- 1 root root 10, 130 Jul 12 18:25 /dev/comcerto_wdt
- Starting watchdog ...
- -rw-r--r-- 1 root root 0 Jul [ 7.378549] MCU watchdog is reset!
- 12 18:25 /proc/mcu_wdt
- [ 7.868440] egiga0: pfe_eth_open
- [ 7.871903] hif_process_client_req: register client_id 0
- [ 7.877249] pfe_hif_client_register
- [ 7.880752] hif_lib_set_rx_cpu_affinity:Client (0) and HIF Rx processing will use same cpu
- [ 7.889058] egiga0: pfe_gemac_init
- [ 7.897247] egiga1: pfe_eth_open
- [ 7.900713] hif_process_client_req: register client_id 1
- [ 7.906061] pfe_hif_client_register
- [ 7.909566] hif_lib_set_rx_cpu_affinity:Client (1) and HIF Rx processing will use same cpu
- [ 7.917929] egiga1: pfe_gemac_init
- cat: can't open '/proc/hdd5_detect': No such file or directory
- *** Stage 2: Prepare the root file system ***
- mknod: /dev/gpio: File exists
- Initialize fan control
- Wrote to 0x90470058: 0x05000000
- Wrote to 0x90458000: 0x80000001
- Wrote to 0x90458028: 0x80001388
- Mount system partition...
- crw-rw---- 1 root root 10, 58 Jul 12 2012 /dev/ubi_ctrl
- sda
- checking sda
- Trying to mount /dev/sda1
- [ 8.731314] FAT-fs (sda1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
- md5 check ok
- + ECHO=/bin/echo
- + FLASH_ERASEALL=/sbin/flash_eraseall
- + ENV_PARTITION=/dev/mtd2
- + USB_PATH=/mnt/partnerkey
- + USB_FW_PATH=/mnt/partnerkey/nas5xx_fw
- + BUFFER_PATH=/mnt/partnerkey/buffer
- + FW_PATH=/firmware
- + exec
- [ 11.882767] PHY: comcerto-0:04 - Link is Up - 1000/Full
- [ 11.888037] pfe_eth_adjust_link: PHY: comcerto-0:04, phy->link: 1
- Doing pre-install ...
- ... pre-install finishes!
- [ 53.083254] UBI: attaching mtd5 to ubi5
- [ 53.810369] UBI: scanning is finished
- [ 53.830630] UBI: attached mtd5 (name "rootfs1", size 110 MiB) to ubi5
- [ 53.837109] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- [ 53.843924] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- [ 53.850643] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
- [ 53.857541] UBI: good PEBs: 880, bad PEBs: 0, corrupted PEBs: 0
- [ 53.863481] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
- [ 53.870636] UBI: max/mean erase counter: 5/3, WL threshold: 4096, image sequence number: 330185502
- [ 53.879625] UBI: available PEBs: 10, total reserved PEBs: 870, PEBs reserved for bad PEB handling: 40
- [ 53.888893] UBI: background thread "ubi_bgt5d" started, PID 998
- [ 53.914977] UBI error: ubi_create_volume: volume "ubi_rootfs1" exists (ID 0)
- [ 53.922052] UBI error: ubi_create_volume: cannot create volume 1, error -17
- [ 54.046913] UBIFS: mounted UBI device 5, volume 0, name "ubi_rootfs1"
- [ 54.053391] UBIFS: file system size: 103612416 bytes (101184 KiB, 98 MiB, 816 LEBs)
- [ 54.061245] UBIFS: journal size: 5206016 bytes (5084 KiB, 4 MiB, 41 LEBs)
- [ 54.068579] UBIFS: media format: w4/r0 (latest is w4/r0)
- [ 54.074432] UBIFS: default compressor: lzo
- [ 54.078538] UBIFS: reserved for root: 4893869 bytes (4779 KiB)
- [ 80.639786] UBIFS: un-mount UBI device 5, volume 0
- [ 80.846941] UBI: attaching mtd7 to ubi7
- [ 81.573927] UBI: scanning is finished
- [ 81.590664] UBI: attached mtd7 (name "rootfs2", size 110 MiB) to ubi7
- [ 81.597151] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- [ 81.603974] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- [ 81.610696] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
- [ 81.617598] UBI: good PEBs: 880, bad PEBs: 0, corrupted PEBs: 0
- [ 81.623542] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
- [ 81.630697] UBI: max/mean erase counter: 5/3, WL threshold: 4096, image sequence number: 1035530652
- [ 81.639774] UBI: available PEBs: 10, total reserved PEBs: 870, PEBs reserved for bad PEB handling: 40
- [ 81.649034] UBI: background thread "ubi_bgt7d" started, PID 1019
- [ 81.679723] UBI error: ubi_create_volume: volume "ubi_rootfs2" exists (ID 0)
- [ 81.686844] UBI error: ubi_create_volume: cannot create volume 1, error -17
- [ 81.815456] UBIFS: mounted UBI device 7, volume 0, name "ubi_rootfs2"
- [ 81.821921] UBIFS: file system size: 103612416 bytes (101184 KiB, 98 MiB, 816 LEBs)
- [ 81.829787] UBIFS: journal size: 5206016 bytes (5084 KiB, 4 MiB, 41 LEBs)
- [ 81.837125] UBIFS: media format: w4/r0 (latest is w4/r0)
- [ 81.842978] UBIFS: default compressor: lzo
- [ 81.847085] UBIFS: reserved for root: 4893869 bytes (4779 KiB)
- [ 108.274176] UBIFS: un-mount UBI device 7, volume 0
- Doing post-install ...
- ... post-install finishes!
- [ 144.946068] Power down.
- [ 144.948531] GPIO[15] is pull high for power off
- [ 148.415283] usb 1-1: USB disconnect, device number 2
Add Comment
Please, Sign In to add comment