2020-01-20 05:07:31 ★ Marcus Wilburn drives the Honda Civic between a two post lift and hops out before adjusting the
2020-01-20 05:07:46 ★ arms on the driver side beneath the pinch welds of the car, moving to the left side and      ((Marcus Wilburn))
2020-01-20 05:07:57 ★ lining the passenger side arms beneath the pinch welds as well.      ((Marcus Wilburn))
2020-01-20 05:08:15 ★ Marcus Wilburn approaches the work bench and emits a sigh as he grabs his wrench and set of
2020-01-20 05:08:25 ★ different size sockets.      ((Marcus Wilburn))
2020-01-20 05:08:37 ★ Marcus Wilburn makes his way back to the car and places the ratchet and the sockets down in
2020-01-20 05:08:45 ★ front of the hood before opening the driver door and leaning in to pull the hood release      ((Marcus Wilburn))
2020-01-20 05:08:48 ★ handle.      ((Marcus Wilburn))
2020-01-20 05:08:58 ★ The hood pops open, Marcus walks up to the front and slides his fingers beneath the hood      ((Marcus Wilburn))
2020-01-20 05:09:06 ★ before raising it up and fixing it with the hood prop.      ((Marcus Wilburn))
2020-01-20 05:09:51 ★ Marcus Wilburn bends over and picks up the ratchet as he fits it with the right size socket and undoes the
2020-01-20 05:09:59 ★ two bolts securing the exhaust heat shield.      ((Marcus Wilburn))
2020-01-20 05:10:07 ★ Marcus Wilburn takes off the exhaust heat shield and tosses it away from the car as he reveals the
2020-01-20 05:10:12 ★ exhaust manifold.      ((Marcus Wilburn))
2020-01-20 05:10:21 ★ Marcus Wilburn replaces the socket on the ratchet and proceeds to undo the bolts securing the
2020-01-20 05:10:31 ★ exhaust manifold to the engine head.      ((Marcus Wilburn))
2020-01-20 05:13:08 ★ Marcus Wilburn puts the ratchet aside and retrives a flat head screwdriver as he starts unscrewing
2020-01-20 05:15:10 ★ the screws mounting the front bumper in place.      ((Marcus Wilburn))
2020-01-20 05:16:43 ★ Marcus Wilburn then unscrews the ones securing the bumper to the plastic splash shield.
2020-01-20 05:17:09 ★ Marcus Wilburn wiggles the bumper off of it's place and carelessly tosses it to the side to make clearance.
2020-01-20 05:18:06 ★ Marcus Wilburn uses the screwdriver to undo the pins on the wire harness to the radiator fan.
2020-01-20 05:18:31 ★ Marcus Wilburn puts away the screwdriver and reaches out for the ratchet, using it to loosen the bolts
2020-01-20 05:18:40 ★ on each corner of the radiator.      ((Marcus Wilburn))
2020-01-20 05:19:08 ★ Marcus Wilburn puts the wrench on the strut tower and grabs the top of the radiator as he fishes out the
2020-01-20 05:19:20 ★ engine bay with a jiggling motion.      ((Marcus Wilburn))
2020-01-20 05:20:22 ★ Marcus Wilburn lets go of the radiator when the hoses connected to it resist the movement.
2020-01-20 05:20:43 ★ Marcus Wilburn grabs the screw driver and loosens the screws on the clamps securing the hoses
2020-01-20 05:21:02 ★ to the radiator, he puts the screwdriver aside and pulls the radiator out of the bay      ((Marcus Wilburn))
2020-01-20 05:21:12 ★ to rest it against the wall in the garage.      ((Marcus Wilburn))
2020-01-20 05:21:59 ★ Marcus Wilburn sighs as he realizes how restless he is, he tried to pull the radiator out the bay without
2020-01-20 05:22:07 ★ removing the hoses connected to it.      ((Marcus Wilburn))
2020-01-20 05:22:49 ★ Marcus Wilburn mumbles as he grabs the ratchet and takes a knee in order to undo the two bolts
2020-01-20 05:23:43 ★ securing the exhaust pipe's flange to the bottom of the exhaust manifold.      ((Marcus Wilburn))
2020-01-20 05:24:10 ★ Marcus Wilburn pushes himself up and uses both hands to pull the exhaust manifold out of its place
2020-01-20 05:24:36 ★ as it's now completely loose, he tosses it near the rest of the junk.      ((Marcus Wilburn))
2020-01-20 05:25:28 ★ Marcus Wilburn grabs the screwdriver and uses it to carelessly tear the tape on the turbo kit carton box.
2020-01-20 05:25:43 ★ Marcus Wilburn pulls the turbo manifold out of the box and undoes the wrapping before head back to
2020-01-20 05:25:50 ★ the car and placing it in the exhaust manifold's place to test fit it.      ((Marcus Wilburn))
2020-01-20 05:25:56 ★ Marcus Wilburn nods a couple times as he fishes out a ziploc bag of bolts from the turbo kit's box.
2020-01-20 05:30:12 ★ Marcus Wilburn refits the turbo manifold in the exhaust manifold's spot and inserts the bolts in the
2020-01-20 05:30:25 ★ holes as he slightly tightens them with his bare fingers.      ((Marcus Wilburn))
2020-01-20 05:30:34 ★ Marcus Wilburn grabs the ratchet and fully secures the said bolts to fix the turbo manifold in place.
2020-01-20 05:30:42 ★ Marcus Wilburn extracts the turbo compressor itself out of the box and slides it through the studs on the
2020-01-20 05:30:49 ★ turbo manifold before hand tightening the lugs and washers that came with it.      ((Marcus Wilburn))
2020-01-20 05:30:56 ★ Marcus Wilburn scoops up the ratchet and uses it to tighten the said lugs in order to firmly secure the
2020-01-20 05:31:03 ★ compressor housing to the turbo manifold.      ((Marcus Wilburn))
2020-01-20 05:32:26 ★ Marcus Wilburn admires the turbo housing sitting on the turbo manifold, he draws a rather wide smile as
2020-01-20 05:32:35 ★ he checks it out from different angles.      ((Marcus Wilburn))
2020-01-20 05:33:38 ★ Marcus Wilburn grabs a remote to the two post lift and pushes a button to raise the car up, enough
2020-01-20 05:33:51 ★ for him to get under it.      ((Marcus Wilburn))
2020-01-20 05:35:09 ★ Marcus Wilburn steps beneath the car with his ratchet, he unplugs the O2 sensor and starts loosening
2020-01-20 05:35:31 ★ the bolts securing the exhaust assembly hangers to the frame of the Honda.      ((Marcus Wilburn))
2020-01-20 05:35:53 ★ Marcus Wilburn stands aside as he does so, making enough space for the exhaust assembly to fall
2020-01-20 05:36:05 ★ down without hitting his feet.      ((Marcus Wilburn))
2020-01-20 05:36:36 ★ Marcus Wilburn finishes undoing the bolts of the exhaust hangers, the system falls after Marcus slightly
2020-01-20 05:36:55 ★ jiggles it, he bends over and grabs the exhaust pipe as he drags it away from beneath      ((Marcus Wilburn))
2020-01-20 05:36:57 ★ the car.      ((Marcus Wilburn))
2020-01-20 05:39:35 ★ Marcus Wilburn pushes a button on the lift remote to lower the car down, he makes his way to the
2020-01-20 05:40:06 ★ bay and yawns as he takes a moment to assess the situation and figure his next move.      ((Marcus Wilburn))
2020-01-20 05:41:14 ★ Marcus Wilburn grabs a plastic container and slides it beneath the oil pan before taking a knee and
2020-01-20 05:41:30 ★ using a 10mm socket on his ratchet to loosen the drain bolt.      ((Marcus Wilburn))
2020-01-20 05:42:02 ★ Marcus Wilburn allows the oil to drain in the plastic container, he lights up a cigarette and waits
2020-01-20 05:42:06 ★ patiently.      ((Marcus Wilburn))
2020-01-20 05:42:55 ★ Marcus Wilburn puffs on his cigarette as he narrows his eyes at the turbo housing.
2020-01-20 05:43:43 ★ Marcus Wilburn drops the cancer stick down and stomps it before approaching the vehicle and
2020-01-20 05:44:01 ★ using the remote to lift it up about a meter for clearance.      ((Marcus Wilburn))
2020-01-20 05:44:33 ★ Marcus Wilburn kneels down and pulls the plastic container away as he using the 10mm socket and ratchet
2020-01-20 05:44:53 ★ to loosen the bolts securing the oil pan to the bottom of the D16 engine.      ((Marcus Wilburn))
2020-01-20 05:45:11 ★ Marcus Wilburn grabs the oil pan and heads to the workbench as he rests it there, he grabs a
2020-01-20 05:45:25 ★ clean fiber towel and wipes off the remaining oil in it.      ((Marcus Wilburn))
2020-01-20 05:46:24 ★ Marcus Wilburn cleans the oil pan and grabs an electric drill as he fits it with a bit.
2020-01-20 05:46:46 ★ Marcus Wilburn turns it on and pulls the trigger in order to steadily drill a hole in the oil pan.
2020-01-20 05:47:13 ★ Marcus Wilburn grabs the oil tap from the turbo kit carton box and inserts it into the hole he drilled.
2020-01-20 05:48:32 ★ Marcus Wilburn nods as he appears satisfied with the tight fit, he takes it off and applies some
2020-01-20 05:48:49 ★ teflon tape to the tap's thread to avoid any future leaks.      ((Marcus Wilburn))
2020-01-20 05:49:36 ★ Marcus Wilburn fits the tap again and secures it before scratching the old gasket on the oil pan.
2020-01-20 05:50:19 ★ Marcus Wilburn grabs an RTV tube and squeezes it as he uses his finger to spread it around the
2020-01-20 05:50:38 ★ oil pan connection surface, creating a new gasket.      ((Marcus Wilburn))
2020-01-20 05:50:55 ★ Marcus Wilburn takes the pan back to the car and fits it in place as he hand tightens the bolts.
2020-01-20 05:51:19 ★ Marcus Wilburn then uses the ratchet and 10mm socket to fully tighten them in a cristian cross pattern to
2020-01-20 05:51:23 ★ avoid leaks.      ((Marcus Wilburn))
2020-01-20 05:55:19 ★ Marcus Wilburn pushes himself up and takes the philips head screwdriver, using it to undo the lid of the
2020-01-20 05:55:27 ★ airbox.      ((Marcus Wilburn))
2020-01-20 05:56:09 ★ Marcus Wilburn scratches his head for a moment before placing the philips head screwdriver aside
2020-01-20 05:56:43 ★ and getting the flat head one, using it to undo the clamp securing the OEM intake tube      ((Marcus Wilburn))
2020-01-20 05:56:58 ★ to the throttle body.      ((Marcus Wilburn))
2020-01-20 05:57:24 ★ Marcus Wilburn grasps on the loose air tube and pulls as hard as he could, eventually breaking the
2020-01-20 05:57:52 ★ OEM airbox off of its place, he tosses it aside carelessly.      ((Marcus Wilburn))
2020-01-20 06:01:48 ★ Marcus Wilburn takes out all the intercooler silicon hoses that came with the kit along with a printed
2020-01-20 06:03:21 ★ diagram and installs the first piece's end to the throttle body, using a clamp to secure it      ((Marcus Wilburn))
2020-01-20 06:03:25 ★ in place.      ((Marcus Wilburn))
2020-01-20 06:04:15 ★ Marcus Wilburn grabs the intercooler itself and rests it on the car's frame where the bumper is
2020-01-20 06:04:37 ★ supposed to go, he continues routing the silicone hoses until he achives the connection      ((Marcus Wilburn))
2020-01-20 06:05:40 ★ from the throttle body to one side of the intercooler, securing the said hoses with the      ((Marcus Wilburn))
2020-01-20 06:05:46 ★ provided clamps.      ((Marcus Wilburn))
2020-01-20 06:06:25 ★ Marcus Wilburn makes a second connection running from the second side of the intercooler to
2020-01-20 06:07:00 ★ the turbine's air outlet.      ((Marcus Wilburn))
2020-01-20 06:07:16 ★ Marcus Wilburn fits clamps on the loose silicone hoses and tightens them with the screwdriver.
2020-01-20 06:08:55 ★ Marcus Wilburn yawns as he inspects the intercooler setup, looking for any mistakes he's done.
2020-01-20 06:09:10  [English] Marcus Wilburn says: Looking good.
2020-01-20 06:09:38 ★ Marcus Wilburn opens a second carton box and takes out a cold air intake assembly, he fits the
2020-01-20 06:10:02 ★ hose onto the compressor's inlet and secures it with the provided clamp by tightening the      ((Marcus Wilburn))
2020-01-20 06:10:06 ★ screw on it down.      ((Marcus Wilburn))
2020-01-20 06:11:42 ★ Marcus Wilburn is seemingly happy with the setup so far, he grabs the oil feed line from the box and
2020-01-20 06:12:12 ★ connects it to the tap he's installed in the oil pan, routing it all the way to the      ((Marcus Wilburn))
2020-01-20 06:13:01 ★ turbo housing afterwards, connecting it in the right slot and using a solid wrench to      ((Marcus Wilburn))
2020-01-20 06:13:06 ★ secure it in place.      ((Marcus Wilburn))
2020-01-20 06:14:00 ★ Marcus Wilburn then proceeds to plug the end of the oil return line to the tap on the oil pan, securing it
2020-01-20 06:14:27 ★ and routing it to the turbo housing as he connects it in the associated slot.      ((Marcus Wilburn))
2020-01-20 06:14:54 ★ Marcus Wilburn secures both ends after applying teflon tape to make sure it wouldn't leak.
2020-01-20 06:17:08 ★ Marcus Wilburn takes the electric drill and fits it with a bit of the right size before drilling into the
2020-01-20 06:17:12 ★ vacuum line.      ((Marcus Wilburn))
2020-01-20 06:18:05 ★ Marcus Wilburn places the drill aside and grabs a T connector as he fits it in the hole's just drilled.
2020-01-20 06:18:52 ★ Marcus Wilburn fishes the blow off valve that came with the kit out the box and connects it to the T
2020-01-20 06:19:18 ★ connection he's just installed, he uses a clamp to tighten it in place.      ((Marcus Wilburn))
2020-01-20 06:23:44 ★ Marcus Wilburn grabs the airbox he's removed earlier and fishes the filter out of it before putting it back
2020-01-20 06:24:33 ★ in place, just rested there for the time being, he moves the cold air filter inside it and      ((Marcus Wilburn))
2020-01-20 06:27:31 ★ emits a sigh as he looks at the engine bay.      ((Marcus Wilburn))
2020-01-20 06:28:23 ★ Marcus Wilburn uses the ratchet to undo the two bolts of the left side of the hood.
2020-01-20 06:28:42 ★ Marcus Wilburn supports the hood with his left hand and undoes the two bolts on the right side, the hood
2020-01-20 06:29:08 ★ prop is making his life easier, when he's done unscrewing the bolts, he quickly tosses      ((Marcus Wilburn))
2020-01-20 06:29:23 ★ the ratchet aside and uses both hands to lift it up with a grunt and move it to the work      ((Marcus Wilburn))
2020-01-20 06:29:27 ★ bench.      ((Marcus Wilburn))
2020-01-20 06:30:46 ★ Marcus Wilburn grabs his torch set and adjusts the gas and oxygen valves, enough of the mixture to spark it
2020-01-20 06:30:51 ★ up.      ((Marcus Wilburn))
2020-01-20 06:31:43 ★ Marcus Wilburn grabs his protective eyewear and puts it on before increasing the gas amount for
2020-01-20 06:32:26 ★ a bigger flame, he cuts a circle big enough for his hood exit plans in the hood.      ((Marcus Wilburn))
2020-01-20 06:33:07 ★ Marcus Wilburn puts out the gas operated torch and places it aside as he gets his angle grinder and uses
2020-01-20 06:33:25 ★ it to smoothen to edges of the circle he's just cut.      ((Marcus Wilburn))
2020-01-20 06:34:15 ★ Marcus Wilburn grunts as he lifts the hood up with all of his might, he moves it back in place and
2020-01-20 06:34:24 ★ lines the holes up with the brackets.      ((Marcus Wilburn))
2020-01-20 06:35:01 ★ Marcus Wilburn supports it with his left hand while using his right one to tighten the bolts in order
2020-01-20 06:35:10 ★ to mount the hood back in place.      ((Marcus Wilburn))
2020-01-20 06:36:15 ★ Marcus Wilburn doesn't take off his protective glasses, he opens another box and takes out a
2020-01-20 06:37:07 ★ 90 degree DIY exhaust pipe, he lines it up with the turbine exhaust outlet while      ((Marcus Wilburn))
2020-01-20 06:37:29 ★ using his left hand to slowly lower the hood to know how much he should cut in order      ((Marcus Wilburn))
2020-01-20 06:37:46 ★ for the pipe to fit through the hood exit hole he's cut.      ((Marcus Wilburn))
2020-01-20 06:38:09 ★ Marcus Wilburn bobs his head and raises the hood back up, applying the prop.
2020-01-20 06:38:29 ★ Marcus Wilburn heads to the workbench and mans the electric saw, he turns the machine on and
2020-01-20 06:38:51 ★ steadily cuts through the pipe to trim it down in order for it to fit his needs.      ((Marcus Wilburn))
2020-01-20 06:39:21 ★ Marcus Wilburn places the saw aside after turning it off, he uses the grinder to smoothen the
2020-01-20 06:39:36 ★ sharp edges produced by the saw.      ((Marcus Wilburn))
2020-01-20 06:39:57 ★ Marcus Wilburn grabs the pipe and test fits it again, seemingly impressed as it meets his needs.
2020-01-20 06:40:51 ★ Marcus Wilburn grabs his TIC welder post closer to the hood and turns the machine on as he adjusts the
2020-01-20 06:40:58 ★ paramets.      ((Marcus Wilburn))
2020-01-20 06:41:41 ★ Marcus Wilburn wears a pair of protective gloves and holds the pipe in place as he carefully
2020-01-20 06:41:51 ★ welds the pipe to the turbine exhaust outlet.      ((Marcus Wilburn))
2020-01-20 06:42:36 ★ Marcus Wilburn ensures he forgets no spots to avoid any possible leaks, he lets go of the pipe once it's in
2020-01-20 06:42:51 ★ place and lowers the hood back and forth to see if there's any clearance issue, apparently      ((Marcus Wilburn))
2020-01-20 06:42:54 ★ none.      ((Marcus Wilburn))
2020-01-20 06:47:16 ★ Marcus Wilburn supports the hood with the prop and grabs the bumper he's removed earlier.
2020-01-20 06:47:43 ★ Marcus Wilburn test fits it and uses a permanent marker to mark where he needs to cut to make enough
2020-01-20 06:48:03 ★ room for his front mount intercooler.      ((Marcus Wilburn))
2020-01-20 06:48:22 ★ Marcus Wilburn takes the bumper to the workbench and turns on the electric saw as he carefully
2020-01-20 06:48:40 ★ cuts through the marked lines to removed the excess material from the bumper.      ((Marcus Wilburn))
2020-01-20 06:49:12 ★ Marcus Wilburn grabs the final product after smoothing the edges with an angle grinder for a hotter look.
2020-01-20 06:49:44 ★ Marcus Wilburn fits the bumper back on and cops a screwdriver as he starts screwing it back
2020-01-20 06:50:15 ★ in place, giving it a gentle pull to see if it's any loose.      ((Marcus Wilburn))
2020-01-20 06:50:43 ★ Marcus Wilburn puts the screwdriver aside and grabs the top of the radiator before lifting it up and
2020-01-20 06:50:51 ★ carefully dropping it back in place.      ((Marcus Wilburn))
2020-01-20 06:51:16 ★ Marcus Wilburn hand fits the radiator hoses back on and uses the screwdriver to screw in the clamps
2020-01-20 06:51:22 ★ in order to tighten them.      ((Marcus Wilburn))
2020-01-20 06:51:48 ★ Marcus Wilburn reconnects the wire harness to the radiator fan and yawns as he checks out the
2020-01-20 06:51:54 ★ progress he's made so far.      ((Marcus Wilburn))
2020-01-20 07:06:08 ★ Marcus Wilburn heads to the back of the car and pops the trunk open before removing the carpet
2020-01-20 07:06:43 ★ covering the cover to the fuel pump assembly.      ((Marcus Wilburn))
2020-01-20 07:07:18 ★ Marcus Wilburn places a bunch of dry towels around the the cover and undoes the bolts prior to fishing
2020-01-20 07:08:04 ★ a flat head screwdriver out of his pocket and using it to undo the harness to the      ((Marcus Wilburn))
2020-01-20 07:08:10 ★ fuel pump assembly.      ((Marcus Wilburn))
2020-01-20 07:08:36 ★ Marcus Wilburn then proceeds to unscrew the lid to reveal the pump itself, he unplugs the electric
2020-01-20 07:08:52 ★ connections and takes it out before throwing it to the side.      ((Marcus Wilburn))
2020-01-20 07:09:13 ★ Marcus Wilburn opens the carton box and takes out a brand new high flow fuel pump, dropping it
2020-01-20 07:09:22 ★ inside the pump assembly and reconnecting the wires.      ((Marcus Wilburn))
2020-01-20 07:09:42 ★ Marcus Wilburn places the lid back on and uses the screwdriver to fix it in place.
2020-01-20 07:10:05 ★ Marcus Wilburn drops the fuel pump assembly back inside the fuel tank through the hole and reconnects the
2020-01-20 07:10:14 ★ wire harness.      ((Marcus Wilburn))
2020-01-20 07:10:41 ★ Marcus Wilburn puts the cover back and tightens the bolts using his ratchet and the right size socket.
2020-01-20 09:11:32 ★ Marcus Wilburn fits his ratcheting wrench with a 10mm socket and undoes the three nuts that secure the
2020-01-20 09:11:45 ★ fuel rail in place.      ((Marcus Wilburn))
2020-01-20 09:12:27 ★ Marcus Wilburn grabs an dry towel and places it beneath the engine before taking an adjustable
2020-01-20 09:12:55 ★ wrench and slowly loosening the nut securing the end of the fuel feed line to the      ((Marcus Wilburn))
2020-01-20 09:13:36 ★ fuel rail, he eases the fuel pressure out the system as the fuel drips down on the      ((Marcus Wilburn))
2020-01-20 09:13:43 ★ dry towel he placed.      ((Marcus Wilburn))
2020-01-20 09:14:06 ★ Marcus Wilburn completely removes the said nut and the washer with it, placing them aside for later
2020-01-20 09:14:08 ★ use.      ((Marcus Wilburn))
2020-01-20 09:14:41 ★ Marcus Wilburn proceeds to do the same with the fuel return hose on the fuel rack, he loosens the nut
2020-01-20 09:15:03 ★ and saves it along with the washer for later installation.      ((Marcus Wilburn))
2020-01-20 09:17:18 ★ Marcus Wilburn eases the fuel rail out of place as he does so extremely slowly trying not to lose
2020-01-20 09:17:52 ★ the rubber seals of the injectors inside.      ((Marcus Wilburn))
2020-01-20 09:20:39 ★ Marcus Wilburn unplugs the wire harness to each injector before taking the fuel rail to the workbench and
2020-01-20 09:24:02 ★ placing a cloth beneath the rail as he places it down on the bench.      ((Marcus Wilburn))
2020-01-20 09:24:35 ★ Marcus Wilburn starts wiggling the OEM injectors out of place and removing them from the fuel
2020-01-20 09:25:12 ★ rail before getting a glass container that has the new high flow injectors soaking in      ((Marcus Wilburn))
2020-01-20 09:25:17 ★ gasoline in it.      ((Marcus Wilburn))
2020-01-20 09:25:50 ★ Marcus Wilburn takes out the new injectors and applies the rubber seals to the tip before fitting them in
2020-01-20 09:26:09 ★ the holes from the fuel rail and applying some pressure until they stop.      ((Marcus Wilburn))
2020-01-20 09:26:38 ★ Marcus Wilburn grabs the fuel rail with the new injectors installed on it, he eases it back in place with
2020-01-20 09:27:00 ★ the new injectors inside the holes on the intake manifold, he watches for the sprayer      ((Marcus Wilburn))
2020-01-20 09:27:17 ★ tips while doing so as they tend to be squishy.      ((Marcus Wilburn))
2020-01-20 09:27:41 ★ Marcus Wilburn hands tightening the three nuts that secure the fuel rail in place and grabs the ratchet
2020-01-20 09:28:29 ★ with the 10mm socket on it, he starts tightening the said nuts until they're snug.      ((Marcus Wilburn))
2020-01-20 09:29:03 ★ Marcus Wilburn grabs the nut and washer from the fuel return line and fits it back on the return port
2020-01-20 09:29:28 ★ from the fuel rack, using the adjustable wrench to fasten the nut until the hose is      ((Marcus Wilburn))
2020-01-20 09:29:34 ★ firmly secured to the rail.      ((Marcus Wilburn))
2020-01-20 09:29:55 ★ Marcus Wilburn grabs the fuel feed line and plugs it to the fuel rail, using the nut and washer from
2020-01-20 09:30:22 ★ earlier to secure them as he tightens them with the 10mm socket fitted on his ratchet.      ((Marcus Wilburn))
2020-01-20 09:34:04 ★ Marcus Wilburn reconnects the wire harnesses to the new injectors as he makes sure they're all
2020-01-20 09:34:17 ★ plugged in properly, slightly shaking them to make sure.      ((Marcus Wilburn))