Rogue System Cold Start Guide

Initial Powerup

Enter Pilot Seat
INST LIGHT - ON
SEAT MODE button - FLIGHT
BATT 1 COVER - OPEN
a. BATT 1 button - ENABLED
(VERIFY CABIN POWER)
b. BATT 1 COVER - CLOSE
FAULT ACK button - PRESS
(Verify CAw Silenced)
BATT TO SYS BUS 1 - TIED
(Verify ECS SYS BUS 1 Powered)
EXT POWER - IN USE
(Verify BATT 1 no longer losing charge)
BATT 2 COVER - OPEN
a. BATT 2 button - ENABLED
b. BATT 2 COVER - CLOSE
BMS KNOB - BATT 2
BATT TO SYS BUS 2 - TIED
(Verify ECS SYS BUS 2 Powered)
Fuel Cell System - Initial Startup
FUEL CELL 1 COVER - OPEN
a. FUEL CELL 1 - STANDBY
(Verify FC1 Core Temp Rise)
b. FUEL CELL 1 COVER - CLOSE
FUEL CELL 2 COVER - OPEN
a. FUEL CELL 2 - STANDBY
b. FUEL CELL 2 COVER - CLOSE
FCS KNOB - FCS 2
(Verify FC2 Core Temp Rise)

Temperature Management System
TM SYS COVER - OPEN
a. TM SYS - ENABLED
(Verify TM SYS panel powered)
b. TM SYS COVER - CLOSE
CL TANK BLADDER - PRSRZ'D
(Verify CLNT PRESS Rise, TANK Fall)
(Verify CLNT PRESS 100psi MINIMUM,else CL TANK BLADDER - DEPR'D)
CL CIRC PUMP PWR - ENABLED
CL CIRC PUMP SPD - NORM
CL RBLC POWER - ENABLED
TMS KNOB - LOOP 2
CL TANK BLADDER - PRSRZ'D
(Verify CLNT PRESS Rise, TANK Fall)
(Verify CLNT PRESS 100psi MINIMUM,else CL TANK BLADDER - DEPR'D)
CL CIRC PUMP PWR - ENABLED
CL CIRC PUMP SPD - NORM
CL RBLC POWER - ENABLED
Cabin HVAC
CABIN HVAC - ENABLED

Communications System

COMM SYS POWER COVER - OPEN
a. COMM SYS POWER ENABLED
b. COMM SYS POWER COVER - CLOSE
XMTR POWER - ENABLED
CONTACT STC - CHECK IN
CONTACT STC - REQUEST DEPARTURE CLEARANCE

LENR and RCS

LENR SYS POWER COVER - OPEN
a. LENR SYS POWER - ENABLED
b. LENR SYS POWER COVER - CLOSE
CORE HEATER - ACTIVE
(Verify CORE TEMP Rise)
RCM SYS POWER COVER - OPEN
a. RCM SYS POWER - ENABLED
b. RCM SYS POWER COVER - CLOSE
TANK 1 BLADDER - PRSRZ'D
TANK 2 BLADDER - PRSRZ'D
TANK 3 BLADDER - PRSRZ'D
TANK 4 BLADDER - PRSRZ'D
RCM KNOB - ROTATE
(Verify each Tank PRESS rising)
LENR VALIDATE REACTANT - VALID
(Press again until TANK 4 selected)
Fuel Cell System - Enable Reaction
FCS VALIDATE - CONS VALID
FCS PURGE CONTAM - ENABLED
FCS KNOB - FCS 1
FCS VALIDATE - CONS VALID
FCS PURGE CONTAM - ENABLED
VMS
MFD DISPLAYS: PWR SET - ENABLED
Navigation and Autopilot
NAS SYS POWER COVER - OPEN
a. NAS SYS POWER - ENABLED
b. NAS SYS POWER COVER - CLOSED
LENR Initiation
CONTACT STC - READY FOR LENR INITIATION
(Verify approval)
LENR FUSE ALLOW - ENABLED
(Verify *FUSE* On LENR Panel)
(Verify Rise in FLOW RATE and CONV EFF)
(Verify MAIN Bus Powered)
MAIN TO SYS BUS 1 - TIED
MAIN TO SYS BUS 2 - TIED
MAIN TO UTIL BUS - TIED
EXT POWER - CUTOFF
BMS CHARGE ALLOW - CHARGING
(Verify BATT 2 Charging)
BMS KNOB - BATT 1
BMS CHARGE ALLOW - CHARGING
(Verify BATT 1 Charging)
MTS and Pre-departure
MTS SYS POWER COVER - OPEN
a. MTS SYS POWER - ENABLED
(Verify MTS Panel Powered)
b. MTS SYS POWER COVER - CLOSED
MTS VALIDATE PROP - VALID
MTS PROP INJECTOR - ENABLED
DOCKING LIGHT - ON
EXT FLOOD LIGHT - ON
NAV LIGHT - ON
VMS - SET APPROPRIATE VIEW

END STARTUP CHECKLIST, PROCEED TO DEPARTURE CHECKLIST
Departure (While still in STC Limiting)
MANEUVER OUT OF STC LIMITER RANGE (>200m)
(Maintain safe speed and situational awareness)
DOCKING LIGHT - OFF
Departure (When out of STC Limiting)
MTS SPRCON COVER- OPEN
a. SPRCON - ENABLED
b. SPRCON COVER - CLOSE
MTS HELICON COUPLER - ENABLED
MTS IGNITE/PROVIDE COVER - OPEN
a. IGNITE/PROVIDE - PRESS AND HOLD
(Release when BURNING indicated)
b. IGNITE/PROVIDE COVER - CLOSE
MTS ICH COUPLER - ENABLED
MES Startup (optional)
MES ME SYS 1 POWER COVER - OPEN
a. ME SYS 1 POWER - ENABLED
(Verify MES Panel Powered)
b. ME SYS 1 POWER COVER - CLOSE
MES 1 HVVFM COVER - OPEN
a. MES 1 HVVFM - ENABLED
b. MES 1 HVVFM COVER - CLOSE
MES 1 RFCS - ENABLED
(Verify SUPERCON Rise on MES Display)

MES ME SYS 2 POWER COVER - OPEN
a. ME SYS 2 POWER - ENABLED
b. ME SYS 2 POWER COVER - CLOSE
MES 2 HVVFM COVER - OPEN
a. MES 2 HVVFM - ENABLED
b. MES 2 HVVFM COVER - CLOSE
MES 2 RFCS - ENABLED
(Verify SUPERCON Rise on MES Display)