Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- [ 0.000000] Linux version 4.9.152 (buildbot@builds-03.infra.lede-project.org) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7549-217219e) ) #0 Mon Jan 28 08:54:32 2019
- [ 0.000000] MyLoader: sysp=aaaa5554, boardp=aaaa5554, parts=aaaa5554
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
- [ 0.000000] SoC: Atheros AR7161 rev 2
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] On node 0 totalpages: 16384
- [ 0.000000] free_area_init_node: node 0, pgdat 8044a204, node_mem_map 81000020
- [ 0.000000] Normal zone: 128 pages used for memmap
- [ 0.000000] Normal zone: 0 pages reserved
- [ 0.000000] Normal zone: 16384 pages, LIFO batch:3
- [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
- [ 0.000000] pcpu-alloc: [0] 0
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- [ 0.000000] Kernel command line: board=WNDR3700 mtdparts=spi0.0:320k(u-boot)ro,128k(u-boot-env)ro,7680k(firmware),64k(art)ro console=ttyS0,115200 rootfstype=squashfs noinitrd
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Writing ErrCtl register=00000000
- [ 0.000000] Readback ErrCtl register=00000000
- [ 0.000000] Memory: 60028K/65536K available (3388K kernel code, 175K rwdata, 448K rodata, 268K init, 211K bss, 5508K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:51
- [ 0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.000MHz
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns
- [ 0.000008] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns
- [ 0.007804] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
- [ 0.070515] pid_max: default: 32768 minimum: 301
- [ 0.075220] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.081828] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.091060] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.100917] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.108051] NET: Registered protocol family 16
- [ 0.113710] MIPS: machine is NETGEAR WNDR3700/WNDR3800/WNDRMAC
- [ 2.573685] random: fast init done
- [ 2.796347] registering PCI controller with io_map_base unset
- [ 2.802089] Can't analyze schedule() prologue at 803ab684
- [ 2.816447] PCI host bridge to bus 0000:00
- [ 2.820600] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
- [ 2.827462] pci_bus 0000:00: root bus resource [io 0x0000]
- [ 2.833029] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
- [ 2.839801] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 2.847755] pci 0000:00:11.0: [168c:ff1d] type 00 class 0x020000
- [ 2.847765] pci 0000:00:11.0: fixup device configuration
- [ 2.854283] pci 0000:00:11.0: reg 0x10: [mem 0x00000000-0x0000ffff]
- [ 2.854336] pci 0000:00:11.0: PME# supported from D0 D3hot
- [ 2.854517] pci 0000:00:12.0: [168c:ff1d] type 00 class 0x020000
- [ 2.854525] pci 0000:00:12.0: fixup device configuration
- [ 2.861064] pci 0000:00:12.0: reg 0x10: [mem 0x00000000-0x0000ffff]
- [ 2.861111] pci 0000:00:12.0: PME# supported from D0 D3hot
- [ 2.861275] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
- [ 2.861301] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
- [ 2.868077] pci 0000:00:12.0: BAR 0: assigned [mem 0x10010000-0x1001ffff]
- [ 2.874883] pci 0000:00:11.0: using irq 40 for pin 1
- [ 2.879837] pci 0000:00:12.0: using irq 41 for pin 1
- [ 2.887557] clocksource: Switched to clocksource MIPS
- [ 2.893436] NET: Registered protocol family 2
- [ 2.898628] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 2.905599] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 2.911996] TCP: Hash tables configured (established 1024 bind 1024)
- [ 2.918448] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 2.924279] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 2.930753] NET: Registered protocol family 1
- [ 2.935144] PCI: CLS 0 bytes, default 32
- [ 2.937396] Crashlog allocated RAM at address 0x3f00000
- [ 2.943602] workingset: timestamp_bits=30 max_order=14 bucket_order=0
- [ 2.955853] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 2.961718] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 2.978858] io scheduler noop registered
- [ 2.982781] io scheduler deadline registered (default)
- [ 2.988301] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 2.996833] console [ttyS0] disabled
- [ 3.020472] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 10625000) is a 16550A
- [ 3.029183] console [ttyS0] enabled
- [ 3.036131] bootconsole [early0] disabled
- [ 3.048980] m25p80 spi0.0: found mx25l6405d, expected m25p80
- [ 3.055089] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
- [ 3.060031] 4 cmdlinepart partitions found on MTD device spi0.0
- [ 3.065935] Creating 4 MTD partitions on "spi0.0":
- [ 3.070734] 0x000000000000-0x000000050000 : "u-boot"
- [ 3.077313] 0x000000050000-0x000000070000 : "u-boot-env"
- [ 3.084374] 0x000000070000-0x0000007f0000 : "firmware"
- [ 3.096506] 2 netgear-fw partitions found on MTD device firmware
- [ 3.102560] 0x000000070000-0x0000001c4440 : "kernel"
- [ 3.108856] 0x0000001c4440-0x0000007f0000 : "rootfs"
- [ 3.115201] mtd: device 4 (rootfs) set to be root filesystem
- [ 3.120943] 1 squashfs-split partitions found on MTD device rootfs
- [ 3.127118] 0x000000410000-0x0000007f0000 : "rootfs_data"
- [ 3.134310] 0x0000007f0000-0x000000800000 : "art"
- [ 3.141044] Realtek RTL8366S ethernet switch driver version 0.2.2
- [ 3.147166] rtl8366s rtl8366s: using GPIO pins 5 (SDA) and 7 (SCK)
- [ 3.153493] rtl8366s rtl8366s: RTL8366 ver. 1 chip found
- [ 3.219233] libphy: rtl8366s: probed
- [ 3.223365] libphy: Fixed MDIO Bus: probed
- [ 3.569230] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
- [ 3.909518] ag71xx ag71xx.1: connected to PHY at rtl8366s:04 [uid=001cc960, driver=Generic PHY]
- [ 3.918847] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:RGMII
- [ 3.926511] NET: Registered protocol family 10
- [ 3.934192] NET: Registered protocol family 17
- [ 3.938729] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
- [ 3.951757] 8021q: 802.1Q VLAN Support v1.8
- [ 3.957322] hctosys: unable to open rtc device (rtc0)
- [ 3.967326] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
- [ 3.975233] Freeing unused kernel memory: 268K
- [ 3.979693] This architecture does not have kernel memory protection.
- [ 4.634775] init: Console is alive
- [ 4.638449] init: - watchdog -
- [ 5.528600] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 5.583535] usbcore: registered new interface driver usbfs
- [ 5.589158] usbcore: registered new interface driver hub
- [ 5.594539] usbcore: registered new device driver usb
- [ 5.603870] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 5.611734] ehci-platform: EHCI generic platform driver
- [ 5.617026] ehci-platform ehci-platform: EHCI Host Controller
- [ 5.622839] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
- [ 5.630861] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
- [ 5.657589] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
- [ 5.664598] hub 1-0:1.0: USB hub found
- [ 5.668706] hub 1-0:1.0: 2 ports detected
- [ 5.674867] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 5.682173] ohci-platform: OHCI generic platform driver
- [ 5.687465] ohci-platform ohci-platform: Generic Platform OHCI controller
- [ 5.694324] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
- [ 5.702325] ohci-platform ohci-platform: irq 14, io mem 0x1c000000
- [ 5.782372] hub 2-0:1.0: USB hub found
- [ 5.786387] hub 2-0:1.0: 2 ports detected
- [ 5.791201] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 5.808858] init: - preinit -
- [ 6.513468] ar71xx: pll_reg 0xb8050010: 0x11110000
- [ 6.513486] eth0: link up (1000Mbps/Full duplex)
- [ 6.536693] random: procd: uninitialized urandom read (4 bytes read)
- [ 9.776322] jffs2: notice: (417) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 9.793079] mount_root: switching to jffs2 overlay
- [ 9.824922] urandom-seed: Seed file not found (/etc/urandom.seed)
- [ 10.007141] eth0: link down
- [ 10.020435] procd: - early -
- [ 10.023406] procd: - watchdog -
- [ 10.633680] procd: - watchdog -
- [ 10.637065] procd: - ubus -
- [ 10.733988] random: ubusd: uninitialized urandom read (4 bytes read)
- [ 10.781825] random: ubusd: uninitialized urandom read (4 bytes read)
- [ 10.788602] random: ubusd: uninitialized urandom read (4 bytes read)
- [ 10.795709] procd: - init -
- [ 11.083243] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 11.093615] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 11.111375] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
- [ 11.119420] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
- [ 11.128837] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 11.141455] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
- [ 11.192634] xt_time: kernel timezone is -0000
- [ 11.237217] PPP generic driver version 2.4.2
- [ 11.243707] NET: Registered protocol family 24
- [ 11.273809] PCI: Enabling device 0000:00:11.0 (0000 -> 0002)
- [ 11.284371] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
- [ 11.292971] ath: EEPROM regdomain: 0x0
- [ 11.292976] ath: EEPROM indicates default country code should be used
- [ 11.292979] ath: doing EEPROM country->regdmn map search
- [ 11.292990] ath: country maps to regdmn code: 0x3a
- [ 11.292994] ath: Country alpha2 being used: US
- [ 11.292997] ath: Regpair used: 0x3a
- [ 11.306150] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
- [ 11.309374] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
- [ 11.395680] PCI: Enabling device 0000:00:12.0 (0000 -> 0002)
- [ 11.406220] ath: phy1: Ignoring endianness difference in EEPROM magic bytes.
- [ 11.414819] ath: EEPROM regdomain: 0x0
- [ 11.414824] ath: EEPROM indicates default country code should be used
- [ 11.414827] ath: doing EEPROM country->regdmn map search
- [ 11.414837] ath: country maps to regdmn code: 0x3a
- [ 11.414842] ath: Country alpha2 being used: US
- [ 11.414845] ath: Regpair used: 0x3a
- [ 11.430206] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
- [ 11.433394] ieee80211 phy1: Atheros AR9280 Rev:2 mem=0xb0010000, irq=41
- [ 11.506265] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 12.436268] urandom_read: 5 callbacks suppressed
- [ 12.436276] random: jshn: uninitialized urandom read (4 bytes read)
- [ 20.629163] ar71xx: pll_reg 0xb8050010: 0x11110000
- [ 20.629198] eth0: link up (1000Mbps/Full duplex)
- [ 20.633893] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- [ 20.675327] br-lan: port 1(eth0.1) entered blocking state
- [ 20.680776] br-lan: port 1(eth0.1) entered disabled state
- [ 20.686528] device eth0.1 entered promiscuous mode
- [ 20.691366] device eth0 entered promiscuous mode
- [ 20.770416] br-lan: port 1(eth0.1) entered blocking state
- [ 20.775816] br-lan: port 1(eth0.1) entered forwarding state
- [ 20.781584] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
- [ 20.867659] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
- [ 21.637646] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- [ 21.644384] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
- [ 130.447602] random: crng init done
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement