Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 1.1.3 (Jan 18 2018 - 02:33:24)
- Board: Ralink APSoC DRAM: 64 MB
- relocate_code Pointer at: 83fb4000
- enable ephy clock...done. rf reg 29 = 5
- SSC disabled.
- spi_wait_nsec: 29
- spi device id: c8 40 17 c8 40 (4017c840)
- Warning: un-recognized chip ID, please update bootloader!
- ============================================
- Ralink UBoot Version: 5.0.0.0
- --------------------------------------------
- ASIC 7620_MP (Port5<->GigaSW)
- DRAM component: 512 Mbits DDR, width 16
- DRAM bus: 16 bit
- Total memory: 64 MBytes
- Flash component: SPI Flash
- Date:Jan 18 2018 Time:02:33:24
- ============================================
- icache: sets:512, ways:4, linesz:32 ,total:65536
- dcache: sets:256, ways:4, linesz:32 ,total:32768
- ##### The CPU freq = 580 MHZ ####
- estimate memory size =64 Mbytes
- rt_rtl8367_init(1705):Begin
- Wait for RTL8367C Ready
- .
- RTL8367C is ready now!
- rt_rtl8367_init(1749):Call Func rt_rtl8367_enableRgmii()
- continue to starting system. 0
- disable switch forward...
- 3: System Boot system code via Flash.(0xbc020000)
- do_bootm:argc=2, addr=0xbc020000
- ## Booting image at bc020000 ...
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80000000) ...
- ## Giving linux memsize in MB, 64
- Starting kernel ...
- [ 0.000000] Linux version 4.4.14 (leks@93-78-139-78) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 50115) ) #21 Tue Sep 4 00:09:39 UTC 2018
- [ 0.000000] Board has DDR2
- [ 0.000000] Analog PMU set to hw control
- [ 0.000000] Digital PMU set to hw control
- [ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
- [ 0.000000] MIPS: machine is TP-Link Archer C5 V4
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Writing ErrCtl register=0002fb7f
- [ 0.000000] Readback ErrCtl register=0002fb7f
- [ 0.000000] Memory: 60776K/65536K available (2879K kernel code, 141K rwdata, 700K rodata, 176K init, 195K bss, 4760K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:256
- [ 0.000000] CPU Clock: 580MHz
- [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
- [ 0.000000] systick: enable autosleep mode
- [ 0.000000] systick: running - mult: 214748, shift: 32
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
- [ 0.000009] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
- [ 0.007571] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
- [ 0.070072] pid_max: default: 32768 minimum: 301
- [ 0.074680] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.081051] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.093261] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.102964] pinctrl core: initialized pinctrl subsystem
- [ 0.108643] NET: Registered protocol family 16
- [ 0.376709] PCI host bridge /pcie@10140000 ranges:
- [ 0.381303] MEM 0x0000000020000000..0x000000002fffffff
- [ 0.386374] IO 0x0000000010160000..0x000000001016ffff
- [ 0.399722] rt2880_gpio 10000600.gpio: registering 24 gpios
- [ 0.405110] rt2880_gpio 10000600.gpio: registering 24 irq handlers
- [ 0.411308] rt2880_gpio 10000638.gpio: registering 16 gpios
- [ 0.416667] rt2880_gpio 10000638.gpio: registering 16 irq handlers
- [ 0.422853] rt2880_gpio 10000660.gpio: registering 32 gpios
- [ 0.428213] rt2880_gpio 10000660.gpio: registering 32 irq handlers
- [ 0.434384] rt2880_gpio 10000688.gpio: registering 1 gpios
- [ 0.439658] rt2880_gpio 10000688.gpio: registering 1 irq handlers
- [ 0.446330] PCI host bridge to bus 0000:00
- [ 0.450252] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
- [ 0.456961] pci_bus 0000:00: root bus resource [io 0xffffffff]
- [ 0.462669] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
- [ 0.469271] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 0.477406] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
- [ 0.485843] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
- [ 0.492204] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
- [ 0.499010] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
- [ 0.505562] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
- [ 0.512586] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
- [ 0.519180] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
- [ 0.526299] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
- [ 0.533284] pci 0000:00:00.0: PCI bridge to [bus 01]
- [ 0.538116] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
- [ 0.544696] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
- [ 0.551732] pci 0000:00:00.0: card - bus=0x0, slot = 0x0 irq=0
- [ 0.557378] pci 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
- [ 0.563973] clocksource: Switched to clocksource systick
- [ 0.570441] NET: Registered protocol family 2
- [ 0.575515] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.582239] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.588456] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.594677] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.600300] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.606690] NET: Registered protocol family 1
- [ 0.611399] rt-timer 10000100.timer: maximum frequency is 1220Hz
- [ 0.618189] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.642938] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.648619] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.660758] io scheduler noop registered
- [ 0.664574] io scheduler deadline registered (default)
- [ 0.669760] ralink-usb-phy usbphy: invalid resource
- [ 0.675133] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
- [ 0.682420] console [ttyS0] disabled
- [ 0.685926] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
- [ 0.695530] console [ttyS0] enabled
- [ 0.695530] console [ttyS0] enabled
- [ 0.702574] bootconsole [early0] disabled
- [ 0.702574] bootconsole [early0] disabled
- [ 0.715329] spi spi0.0: force spi mode3
- [ 0.719722] m25p80 spi0.0: gd25q64 (8192 Kbytes)
- [ 0.724531] 6 ofpart partitions found on MTD device spi0.0
- [ 0.730123] Creating 6 MTD partitions on "spi0.0":
- [ 0.735031] 0x000000000000-0x000000020000 : "u-boot"
- [ 0.741777] 0x000000020000-0x0000007c0000 : "firmware"
- [ 0.810515] 2 tplink-fw partitions found on MTD device firmware
- [ 0.816596] 0x000000020000-0x0000001589a0 : "kernel"
- [ 0.823166] 0x0000001589a0-0x0000007c0000 : "rootfs"
- [ 0.829998] mtd: device 3 (rootfs) set to be root filesystem
- [ 0.835983] 1 squashfs-split partitions found on MTD device rootfs
- [ 0.842303] 0x0000003e0000-0x0000007c0000 : "rootfs_data"
- [ 0.849597] 0x0000007c0000-0x0000007d0000 : "config"
- [ 0.856472] 0x0000007d0000-0x0000007e0000 : "rom"
- [ 0.862918] 0x0000007e0000-0x0000007f0000 : "romfile"
- [ 0.869837] 0x0000007f0000-0x000000800000 : "radio"
- [ 0.877078] Realtek RTL8366S ethernet switch driver version 0.2.2
- [ 0.883424] rtl8366s rtl8366s: using GPIO pins 1 (SDA) and 2 (SCK)
- [ 0.889861] rtl8366s rtl8366s: unknown chip id (0303)
- [ 0.895028] rtl8366s rtl8366s: chip detection failed, err=-19
- [ 0.904276] gsw: setting port4 to ephy mode
- [ 0.908734] mtk_soc_eth 10100000.ethernet: using fixed link parameters
- [ 0.915485] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
- [ 0.922229] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
- [ 0.931221] rt2880_wdt 10000120.watchdog: Initialized
- [ 0.937830] NET: Registered protocol family 10
- [ 0.945949] NET: Registered protocol family 17
- [ 0.950576] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 0.963512] 8021q: 802.1Q VLAN Support v1.8
- [ 0.982756] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
- [ 0.990982] Freeing unused kernel memory: 176K (803a4000 - 803d0000)
- [ 3.422349] init: Console is alive
- [ 3.426180] init: - watchdog -
- [ 5.225486] usbcore: registered new interface driver usbfs
- [ 5.231173] usbcore: registered new interface driver hub
- [ 5.236754] usbcore: registered new device driver usb
- [ 5.247426] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 5.255652] ehci-platform: EHCI generic platform driver
- [ 5.271341] phy phy-usbphy.0: remote usb device wakeup disabled
- [ 5.277394] phy phy-usbphy.0: UTMI 16bit 30MHz
- [ 5.281955] ehci-platform 101c0000.ehci: EHCI Host Controller
- [ 5.287863] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
- [ 5.296072] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
- [ 5.306514] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
- [ 5.313952] hub 1-0:1.0: USB hub found
- [ 5.318228] hub 1-0:1.0: 1 port detected
- [ 5.325160] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 5.332919] ohci-platform: OHCI generic platform driver
- [ 5.338604] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
- [ 5.345578] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
- [ 5.353772] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
- [ 5.384403] hub 2-0:1.0: USB hub found
- [ 5.388579] hub 2-0:1.0: 1 port detected
- [ 5.398554] init: - preinit -
- [ 6.351617] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
- [ 6.359964] 8021q: adding VLAN 0 to HW filter on device eth0
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 7.376616] jffs2: notice: (341) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 7.394919] mount_root: switching to jffs2 overlay
- [ 7.424252] mtk_soc_eth 10100000.ethernet eth0: port 5 link down
- [ 7.439980] procd: - early -
- [ 7.443033] procd: - watchdog -
- [ 7.872464] procd: - ubus -
- [ 7.910059] random: ubusd urandom read with 16 bits of entropy available
- [ 7.918727] procd: - init -
- Please press Enter to activate this console.
- [ 8.697014] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 8.716080] Loading modules backported from Linux version wt-2016-05-12-0-g7a54796
- [ 8.723813] Backport generated by backports.git backports-20160216-0-ge3c56e4
- [ 8.778811] mt76x2e 0000:01:00.0: ASIC revision: 76120044
- [ 8.794587] ROM patch already applied
- [ 8.800166] Firmware Version: 0.0.00
- [ 8.803871] Build: 1
- [ 8.806096] Build Time: 201507311614____
- [ 8.820092] Firmware running!
- [ 8.849400] i2c /dev entries driver
- [ 8.888569] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 8.923900] nf_conntrack version 0.5.0 (952 buckets, 3808 max)
- [ 8.985167] xt_time: kernel timezone is -0000
- [ 9.002537] PPP generic driver version 2.4.2
- [ 9.009793] NET: Registered protocol family 24
- [ 9.032304] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected
- [ 9.040291] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 7620 detected
- [ 16.576628] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
- [ 16.584895] 8021q: adding VLAN 0 to HW filter on device eth0
- [ 16.646926] device eth0.1 entered promiscuous mode
- [ 16.651833] device eth0 entered promiscuous mode
- [ 16.716154] br-lan: port 1(eth0.1) entered forwarding state
- [ 16.721887] br-lan: port 1(eth0.1) entered forwarding state
- [ 18.715076] br-lan: port 1(eth0.1) entered forwarding state
- [ 19.975938] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
- [ 19.986597] device wlan1 entered promiscuous mode
- [ 20.007141] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
- [ 20.013805] br-lan: port 2(wlan1) entered forwarding state
- [ 20.019511] br-lan: port 2(wlan1) entered forwarding state
- [ 20.768539] br-lan: port 2(wlan1) entered forwarding state
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement