cnxsoft

sabrelite timesys

Jul 14th, 2013
499
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. U-Boot 2009.08 (Aug 16 2012 - 10:06:42)
  2.  
  3. CPU: Freescale i.MX 6 family 0.0V at 792 MHz
  4. Temperature: 28 C, calibration data 0x5b25247d
  5. mx6q pll1: 792MHz
  6. mx6q pll2: 528MHz
  7. mx6q pll3: 480MHz
  8. mx6q pll8: 50MHz
  9. ipg clock : 66000000Hz
  10. ipg per clock : 66000000Hz
  11. uart clock : 80000000Hz
  12. cspi clock : 60000000Hz
  13. ahb clock : 132000000Hz
  14. axi clock : 264000000Hz
  15. emi_slow clock: 29333333Hz
  16. ddr clock : 528000000Hz
  17. usdhc1 clock : 200000000Hz
  18. usdhc2 clock : 200000000Hz
  19. usdhc3 clock : 200000000Hz
  20. usdhc4 clock : 200000000Hz
  21. nfc clock : 24000000Hz
  22. Board: MX6Q-SABRELITE:[ POR]
  23. Boot Device: I2C
  24. I2C: ready
  25. DRAM: 1 GB
  26. MMC: FSL_USDHC: 0,FSL_USDHC: 1
  27. JEDEC ID: 0xbf:0x25:0x41
  28. Reading SPI NOR flash 0xc0000 [0x2000 bytes] -> ram 0x276009b8
  29. SUCCESS
  30.  
  31. *** Warning - bad CRC, using default environment
  32.  
  33. In: serial
  34. Out: serial
  35. Err: serial
  36. Net: got MAC address from IIM: 00:00:00:00:00:00
  37. FEC0 [PRIME]
  38. Hit any key to stop autoboot: 0
  39. Card did not respond to voltage select!
  40. mmc0(part 0) is current device
  41. MMC: block number 0x1 exceeds max(0x0)
  42. ** Can't read from device 0 **
  43.  
  44. ** Unable to use mmc 0:1 for fatload **
  45. ** Bad partition 1 **
  46. mmc1 is current device
  47. reading /6q_bootscript
  48.  
  49. ** Unable to read "/6q_bootscript" from mmc 1:1 **
  50. Loading file "/6q_bootscript" from mmc device 1:1 (xxb1)
  51. 361 bytes read
  52. ## Executing script at 10008000
  53. Loading file "/boot/uImage" from mmc device 1:1 (xxb1)
  54. 3627844 bytes read
  55. ## Booting kernel from Legacy Image at 10800000 ...
  56. Image Name: Linux-3.0.15-ts-armv7l
  57. Image Type: ARM Linux Kernel Image (uncompressed)
  58. Data Size: 3627780 Bytes = 3.5 MB
  59. Load Address: 10008000
  60. Entry Point: 10008000
  61. Verifying Checksum ... OK
  62. Loading Kernel Image ... OK
  63. OK
  64.  
  65. Starting kernel ...
  66.  
  67. Uncompressing Linux... done, booting the kernel.
  68. Linux version 3.0.15-ts-armv7l (fourier@fourier-desktop) (gcc version 4.6.3 (Ti2
  69. CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
  70. CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
  71. Machine: Freescale i.MX 6Quad Sabre-Lite Board
  72. Memory policy: ECC disabled, Data cache writealloc
  73. PERCPU: Embedded 7 pages/cpu @8c008000 s5440 r8192 d15040 u32768
  74. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227328
  75. Kernel command line: console=ttymxc1,115200 video=mxcfb0:dev=hdmi,1280x720M@60,c
  76. PID hash table entries: 4096 (order: 2, 16384 bytes)
  77. Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  78. Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  79. Memory: 640MB 256MB = 896MB total
  80. Memory: 897440k/897440k available, 151136k reserved, 0K highmem
  81. Virtual kernel memory layout:
  82. vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  83. fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  84. DMA : 0xf4600000 - 0xffe00000 ( 184 MB)
  85. vmalloc : 0xc0800000 - 0xf2000000 ( 792 MB)
  86. lowmem : 0x80000000 - 0xc0000000 (1024 MB)
  87. pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
  88. modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
  89. .init : 0x80008000 - 0x8003c000 ( 208 kB)
  90. .text : 0x8003c000 - 0x80a2c110 (10177 kB)
  91. .data : 0x80a2e000 - 0x80a7f940 ( 327 kB)
  92. .bss : 0x80a7f964 - 0x80aaa8cc ( 172 kB)
  93. SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  94. Preemptible hierarchical RCU implementation.
  95. NR_IRQS:496
  96. MXC GPIO hardware
  97. sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
  98. MXC_Early serial console at MMIO 0x21e8000 (options '115200')
  99. bootconsole [ttymxc1] enabled
  100. Console: colour dummy device 80x30
  101. Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
  102. pid_max: default: 32768 minimum: 301
  103. Mount-cache hash table entries: 512
  104. CPU: Testing write buffer coherency: ok
  105. hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
  106. CPU1: Booted secondary processor
  107. CPU2: Booted secondary processor
  108. CPU3: Booted secondary processor
  109. Brought up 4 CPUs
  110. SMP: Total of 4 processors activated (6324.22 BogoMIPS).
  111. print_constraints: dummy:
  112. NET: Registered protocol family 16
  113. print_constraints: vddpu: 725 <--> 1300 mV at 1150 mV fast normal
  114. print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal
  115. print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal
  116. print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
  117. print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
  118. print_constraints: vdd3p0: 2800 <--> 3150 mV at 3000 mV fast normal
  119. hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
  120. hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
  121. hw-breakpoint: maximum watchpoint size is 4 bytes.
  122. L310 cache controller enabled
  123. l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x02070000, Cache size: 1048576 B
  124. IMX usb wakeup probe
  125. IMX usb wakeup probe
  126. bio: create slab <bio-0> at 0
  127. print_constraints: VDDA: 2500 mV
  128. print_constraints: VDDIO: 3300 mV
  129. machine_constraints_voltage: VDDD: unsupportable voltage constraints
  130. reg-fixed-voltage reg-fixed-voltage.2: Failed to register regulator: -22
  131. reg-fixed-voltage: probe of reg-fixed-voltage.2 failed with error -22
  132. print_constraints: vmmc: 3300 mV
  133. SCSI subsystem initialized
  134. spi_imx imx6q-ecspi.0: probed
  135. usbcore: registered new interface driver usbfs
  136. usbcore: registered new interface driver hub
  137. usbcore: registered new device driver usb
  138. Freescale USB OTG Driver loaded, $Revision: 1.55 $
  139. add wake up source irq 75
  140. imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
  141. imx-ipuv3 imx-ipuv3.1: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
  142. mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 driver probed
  143. mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 dphy version is 0x3130302a
  144. MIPI CSI2 driver module loaded
  145. Advanced Linux Sound Architecture Driver Version 1.0.24.
  146. Bluetooth: Core ver 2.16
  147. NET: Registered protocol family 31
  148. Bluetooth: HCI device and connection manager initialized
  149. Bluetooth: HCI socket layer initialized
  150. Bluetooth: L2CAP socket layer initialized
  151. Bluetooth: SCO socket layer initialized
  152. cfg80211: Calling CRDA to update world regulatory domain
  153. i2c-core: driver [max17135] using legacy suspend method
  154. i2c-core: driver [max17135] using legacy resume method
  155. Switching to clocksource mxc_timer1
  156. Switched to NOHz mode on CPU #0
  157. Switched to NOHz mode on CPU #2
  158. Switched to NOHz mode on CPU #1
  159. Switched to NOHz mode on CPU #3
  160. NET: Registered protocol family 2
  161. IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
  162. TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
  163. TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
  164. TCP: Hash tables configured (established 131072 bind 65536)
  165. TCP reno registered
  166. UDP hash table entries: 512 (order: 2, 16384 bytes)
  167. UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  168. NET: Registered protocol family 1
  169. RPC: Registered named UNIX socket transport module.
  170. RPC: Registered udp transport module.
  171. RPC: Registered tcp transport module.
  172. RPC: Registered tcp NFSv4.1 backchannel transport module.
  173. Static Power Management for Freescale i.MX6
  174. cpaddr = c0884000 suspend_iram_base=c0932000
  175. PM driver module loaded
  176. i.MXC CPU frequency driver
  177. JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
  178. msgmni has been set to 1752
  179. io scheduler noop registered
  180. io scheduler deadline registered
  181. io scheduler cfq registered (default)
  182. MIPI DSI driver module loaded
  183. mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi
  184. mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0xa:0xa0:0xc1
  185. fbcvt: 1280x720@60: CVT Name - .921M9
  186. imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
  187. Console: switching to colour frame buffer device 160x45
  188. mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver ldb
  189. mxc_ldb mxc_ldb: Input pixel format not valid use default RGB666
  190. _regulator_get: get() with no identifier
  191. mxc_sdc_fb mxc_sdc_fb.2: register mxc display driver ldb
  192. mxc_sdc_fb mxc_sdc_fb.3: register mxc display driver ldb
  193. mxc_sdc_fb mxc_sdc_fb.3: ipu1-di1 already in use
  194. mxc_sdc_fb: probe of mxc_sdc_fb.3 failed with error -16
  195. imx-sdma imx-sdma: loaded firmware 1.1
  196. imx-sdma imx-sdma: initialized
  197. Serial: IMX driver
  198. imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
  199. imx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX
  200. console [ttymxc1] enabled, bootconsole disabled
  201. console [ttymxc1] enabled, bootconsole disabled
  202. loop: module loaded
  203. Can't recover from RESET HBA!
  204. No sata disk.
  205. m25p80 spi0.0: sst25vf016b (2048 Kbytes)
  206. Creating 2 MTD partitions on "m25p80":
  207. 0x000000000000-0x000000040000 : "bootloader"
  208. 0x000000040000-0x000000200000 : "kernel"
  209. vcan: Virtual CAN interface driver
  210. CAN device driver interface
  211. flexcan netdevice driver
  212. flexcan imx6q-flexcan.0: device registered (reg_base=c09a8000, irq=142)
  213. FEC Ethernet Driver
  214. fec_enet_mii_bus: probed
  215. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  216. fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
  217. fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
  218. fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
  219. fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
  220. hub 1-0:1.0: USB hub found
  221. hub 1-0:1.0: 1 port detected
  222. add wake up source irq 72
  223. fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
  224. fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
  225. fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
  226. fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
  227. hub 2-0:1.0: USB hub found
  228. hub 2-0:1.0: 1 port detected
  229. Initializing USB Mass Storage driver...
  230. usbcore: registered new interface driver usb-storage
  231. USB Mass Storage support registered.
  232. ARC USBOTG Device Controller driver (1 August 2005)
  233. mousedev: PS/2 mouse device common for all mice
  234. input: gpio-keys as /devices/platform/gpio-keys/input/input0
  235. egalax_ts 2-0004: egalax_ts: failed to read firmware version
  236. egalax_ts: probe of 2-0004 failed with error -5
  237. i2c-core: driver [isl29023] using legacy suspend method
  238. i2c-core: driver [isl29023] using legacy resume method
  239. snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0
  240. i2c /dev entries driver
  241. Linux video capture interface: v2.00
  242. mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16
  243. mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17
  244. mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18
  245. mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video19
  246. mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video20
  247. i2c-core: driver [mag3110] using legacy suspend method
  248. i2c-core: driver [mag3110] using legacy resume method
  249. imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
  250. Bluetooth: Virtual HCI driver ver 1.3
  251. Bluetooth: HCI UART driver ver 2.2
  252. Bluetooth: HCIATH3K protocol initialized
  253. Bluetooth: Generic Bluetooth USB driver ver 0.6
  254. usbcore: registered new interface driver btusb
  255. sdhci: Secure Digital Host Controller Interface driver
  256. sdhci: Copyright(c) Pierre Ossman
  257. mmc0: Unknown controller version (3). You may experience problems.
  258. mmc0: SDHCI controller on platform [sdhci-esdhc-imx.3] using ADMA
  259. mmc1: Unknown controller version (3). You may experience problems.
  260. mmc1: SDHCI controller on platform [sdhci-esdhc-imx.2] using ADMA
  261. mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
  262. VPU initialized
  263. mxc_asrc registered
  264. Anatop Thermal registered as thermal_zone0
  265. anatop_thermal_probe: default cooling device is cpufreq!
  266. usbcore: registered new interface driver usbhid
  267. usbhid: USB HID core driver
  268. usbcore: registered new interface driver snd-usb-audio
  269. usb 2-1: new high speed USB device number 2 using fsl-ehci
  270. mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
  271. Cirrus Logic CS42888 ALSA SoC Codec Driver
  272. i2c-core: driver [cs42888] using legacy suspend method
  273. i2c-core: driver [cs42888] using legacy resume method
  274. sgtl5000 0-000a: Failed to get supply 'VDDD': -19
  275. print_constraints: 0-000a: 850 <--> 1600 mV at 1200 mV normal
  276. sgtl5000 0-000a: sgtl5000 revision 17
  277. mmc0: new SDHC card at address 1234
  278. mmcblk0: mmc0:1234 SA04G 3.63 GiB
  279. mmcblk0: p1
  280. asoc: sgtl5000 <-> imx-ssi.1 mapping ok
  281. imx_3stack asoc driver
  282. asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok
  283. ALSA device list:
  284. #0: sgtl5000-audio
  285. #1: imx-hdmi-soc
  286. NET: Registered protocol family 26
  287. TCP cubic registered
  288. NET: Registered protocol family 17
  289. can: controller area network core (rev 20090105 abi 8)
  290. NET: Registered protocol family 29
  291. can: raw protocol (rev 20090105)
  292. can: broadcast manager protocol (rev 20090105 t)
  293. Bluetooth: RFCOMM TTY layer initialized
  294. Bluetooth: RFCOMM socket layer initialized
  295. Bluetooth: RFCOMM ver 1.11
  296. Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  297. Bluetooth: BNEP filters: protocol multicast
  298. Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  299. lib80211: common routines for IEEE802.11 drivers
  300. VFP support v0.3:
  301. hub 2-1:1.0: USB hub found
  302. implementor 41 architecture 3 part 30 variant 9 rev 4
  303. hub 2-1:1.0: 3 ports detected
  304. Bus freq driver module loaded
  305. mxc_dvfs_core_probe
  306. DVFS driver module loaded
  307. snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 00:00:00 UTC (0)
  308. EXT3-fs: barriers not enabled
  309. kjournald starting. Commit interval 5 seconds
  310. EXT3-fs (mmcblk0p1): using internal journal
  311. EXT3-fs (mmcblk0p1): recovery complete
  312. EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode
  313. VFS: Mounted root (ext3 filesystem) on device 179:1.
  314. Freeing init memory: 208K
  315. init started: BusyBox v1.20.2 (2012-08-16 10:09:55 EDT)
  316. Thermal: fuse data 0x5b25247d
  317. Setting hotplug handler: [ OK ]
  318. Creating device files: Auto-mount of [/media/mmcblk0p1] successful
  319. [ OK ]
  320. modprobe: module tsc2004 not found in modules.dep
  321. modprobe: module egalax_ts not found in modules.dep
  322. modprobe: module ft5x06_ts not found in modules.dep
  323. Starting system logging.
  324. Configuring network interfaces: done
  325. Starting dropbear sshd: OK
  326. Finding touchscreen using legacy method:[FAIL]
  327. Finding mouse:[FAIL]
  328. Framebuffer fb0
  329. Resolution 1280 720
  330. Screen resolution: 1280 x 720
  331. HDMI display
  332. Search for input device Acer T230H
  333. Mouse device is Auto
  334. cat: can't open '/etc/ts.dev': No such file or directory
  335. Starting demo...
  336. Starting demo...
  337.  
  338. BusyBox v1.20.2 (2012-08-16 10:09:55 EDT) built-in shell (ash)
  339. Enter 'help' for a list of built-in commands.
  340.  
  341. #
RAW Paste Data