Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- ; Configuration file for Duet WiFi (firmware version 3)
- ; executed by the firmware on start-up
- ;
- ; generated by RepRapFirmware Configuration Tool v3.2.2 on Thu Jan 28 2021 08:56:19 GMT+0100 (Central European Standard Time)
- ; General preferences
- G90 ; send absolute coordinates...
- M83 ; ...but relative extruder moves
- M550 P"HevORT" ; set printer name
- M669 K1 ; select CoreXY mode
- ; Network
- M552 S1 ; enable network
- M586 P0 S1 ; enable HTTP
- M586 P1 S0 ; disable FTP
- M586 P2 S0 ; disable Telnet
- ; Drives
- M569 P0 S1 ; physical drive 0 goes forwards
- M569 P1 S1 ; physical drive 1 goes forwards
- M569 P2 S1 ; physical drive 2 goes forwards
- M569 P3 S1 ; physical drive 3 goes forwards
- M569 P5 S1 ; physical drive 5 goes forwards
- M569 P6 S1 ; physical drive 6 goes forwards
- M584 X0 Y1 Z5:6:2 E3 ; set drive mapping
- M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
- M92 X160.00 Y160.00 Z800.00 E415.00 ; set steps per mm
- M566 X1200.00 Y1200.00 Z30.00 E1800.00 ; set maximum instantaneous speed changes (mm/min)
- M203 X18000.00 Y18000.00 Z1800.00 E3000.00 ; set maximum speeds (mm/min)
- M201 X1600.00 Y1600.00 Z100.00 E2000.00 ; set accelerations (mm/s^2)
- M906 X1200 Y1200 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
- M84 S30 ; Set idle timeout
- ; Axis Limits
- M208 X0 Y0 Z0 S1 ; set axis minima
- M208 X355 Y355 Z400 S0 ; set axis maxima
- ; Endstops
- M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
- M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
- M574 Z1 S2 ; configure Z-probe endstop for low end on Z
- ; Z-Probe
- M950 S0 C"duex.pwm1" ; create servo pin 0 for BLTouch
- M558 P9 C"^zprobe.in" H15 F120 T9000 ; set Z probe type to bltouch and the dive height + speeds
- G31 P500 X37,449 Y26,253 Z2.5 ; set Z probe trigger value, offset and trigger height
- M557 X15:215 Y15:195 S20 ; define mesh grid
- ; Heaters
- M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
- M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
- M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
- M140 H0 ; map heated bed to heater 0
- M143 H0 S120 ; set temperature limit for heater 0 to 120C
- M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
- M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
- M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
- M143 H1 S280 ; set temperature limit for heater 1 to 280C
- ; Fans
- M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
- M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
- M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
- M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
- ; Tools
- M563 P0 D0 H1 F0 ; define tool 0
- G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
- G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
- ; Custom settings are not defined
- ; Miscellaneous
- M911 S22 R23.5 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
- ; Triple Z
- M671 X-13,298:182,911:379,12 Y2,021:370,231:2,021 S50
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
