Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- pi@raspberrypi:~ $ iw list
- Wiphy phy17
- max # scan SSIDs: 4
- max scan IEs length: 2257 bytes
- max # sched scan SSIDs: 0
- max # match sets: 0
- max # scan plans: 1
- max scan plan interval: -1
- max scan plan iterations: 0
- Retry short long limit: 2
- Coverage class: 0 (up to 0m)
- Device supports RSN-IBSS.
- Supported Ciphers:
- * WEP40 (00-0f-ac:1)
- * WEP104 (00-0f-ac:5)
- * TKIP (00-0f-ac:2)
- * CCMP-128 (00-0f-ac:4)
- * CCMP-256 (00-0f-ac:10)
- * GCMP-128 (00-0f-ac:8)
- * GCMP-256 (00-0f-ac:9)
- * CMAC (00-0f-ac:6)
- * CMAC-256 (00-0f-ac:13)
- * GMAC-128 (00-0f-ac:11)
- * GMAC-256 (00-0f-ac:12)
- Available Antennas: TX 0 RX 0
- Supported interface modes:
- * IBSS
- * managed
- * AP
- * AP/VLAN
- * monitor
- * mesh point
- Band 1:
- Capabilities: 0x17e
- HT20/HT40
- SM Power Save disabled
- RX Greenfield
- RX HT20 SGI
- RX HT40 SGI
- RX STBC 1-stream
- Max AMSDU length: 3839 bytes
- No DSSS/CCK HT40
- Maximum RX AMPDU length 32767 bytes (exponent: 0x002)
- Minimum RX AMPDU time spacing: 2 usec (0x04)
- HT TX/RX MCS rate indexes supported: 0-7, 32
- Bitrates (non-HT):
- * 1.0 Mbps
- * 2.0 Mbps (short preamble supported)
- * 5.5 Mbps (short preamble supported)
- * 11.0 Mbps (short preamble supported)
- * 6.0 Mbps
- * 9.0 Mbps
- * 12.0 Mbps
- * 18.0 Mbps
- * 24.0 Mbps
- * 36.0 Mbps
- * 48.0 Mbps
- * 54.0 Mbps
- Frequencies:
- * 2412 MHz [1] (36.0 dBm)
- * 2417 MHz [2] (36.0 dBm)
- * 2422 MHz [3] (36.0 dBm)
- * 2427 MHz [4] (36.0 dBm)
- * 2432 MHz [5] (36.0 dBm)
- * 2437 MHz [6] (36.0 dBm)
- * 2442 MHz [7] (36.0 dBm)
- * 2447 MHz [8] (36.0 dBm)
- * 2452 MHz [9] (36.0 dBm)
- * 2457 MHz [10] (36.0 dBm)
- * 2462 MHz [11] (36.0 dBm)
- * 2467 MHz [12] (36.0 dBm)
- * 2472 MHz [13] (36.0 dBm)
- * 2484 MHz [14] (disabled)
- Supported commands:
- * new_interface
- * set_interface
- * new_key
- * start_ap
- * new_station
- * new_mpath
- * set_mesh_config
- * set_bss
- * authenticate
- * associate
- * deauthenticate
- * disassociate
- * join_ibss
- * join_mesh
- * set_tx_bitrate_mask
- * frame
- * frame_wait_cancel
- * set_wiphy_netns
- * set_channel
- * set_wds_peer
- * probe_client
- * set_noack_map
- * register_beacons
- * start_p2p_device
- * set_mcast_rate
- * connect
- * disconnect
- * set_qos_map
- * set_multicast_to_unicast
- Supported TX frame types:
- * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- Supported RX frame types:
- * IBSS: 0x40 0xb0 0xc0 0xd0
- * managed: 0x40 0xd0
- * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- * mesh point: 0xb0 0xc0 0xd0
- * P2P-client: 0x40 0xd0
- * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- * P2P-device: 0x40 0xd0
- software interface modes (can always be added):
- * AP/VLAN
- * monitor
- valid interface combinations:
- * #{ AP, mesh point } <= 8,
- total <= 8, #channels <= 1
- HT Capability overrides:
- * MCS: ff ff ff ff ff ff ff ff ff ff
- * maximum A-MSDU length
- * supported channel width
- * short GI for 40 MHz
- * max A-MPDU length exponent
- * min MPDU start spacing
- Device supports TX status socket option.
- Device supports HT-IBSS.
- Device supports SAE with AUTHENTICATE command
- Device supports low priority scan.
- Device supports scan flush.
- Device supports AP scan.
- Device supports per-vif TX power setting
- Driver supports full state transitions for AP/GO clients
- Driver supports a userspace MPM
- Device supports configuring vdev MAC-addr on create.
- Supported extended features:
- * [ RRM ]: RRM
- * [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
- * [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
- * [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
- Wiphy phy0
- max # scan SSIDs: 10
- max scan IEs length: 2048 bytes
- max # sched scan SSIDs: 16
- max # match sets: 16
- max # scan plans: 1
- max scan plan interval: 508
- max scan plan iterations: 0
- Retry short limit: 7
- Retry long limit: 4
- Coverage class: 0 (up to 0m)
- Device supports roaming.
- Device supports T-DLS.
- Supported Ciphers:
- * WEP40 (00-0f-ac:1)
- * WEP104 (00-0f-ac:5)
- * TKIP (00-0f-ac:2)
- * CCMP-128 (00-0f-ac:4)
- * CMAC (00-0f-ac:6)
- Available Antennas: TX 0 RX 0
- Supported interface modes:
- * IBSS
- * managed
- * AP
- * P2P-client
- * P2P-GO
- * P2P-device
- Band 1:
- Capabilities: 0x1062
- HT20/HT40
- Static SM Power Save
- RX HT20 SGI
- RX HT40 SGI
- No RX STBC
- Max AMSDU length: 3839 bytes
- DSSS/CCK HT40
- Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
- Minimum RX AMPDU time spacing: 16 usec (0x07)
- HT TX/RX MCS rate indexes supported: 0-7
- Bitrates (non-HT):
- * 1.0 Mbps
- * 2.0 Mbps (short preamble supported)
- * 5.5 Mbps (short preamble supported)
- * 11.0 Mbps (short preamble supported)
- * 6.0 Mbps
- * 9.0 Mbps
- * 12.0 Mbps
- * 18.0 Mbps
- * 24.0 Mbps
- * 36.0 Mbps
- * 48.0 Mbps
- * 54.0 Mbps
- Frequencies:
- * 2412 MHz [1] (20.0 dBm)
- * 2417 MHz [2] (20.0 dBm)
- * 2422 MHz [3] (20.0 dBm)
- * 2427 MHz [4] (20.0 dBm)
- * 2432 MHz [5] (20.0 dBm)
- * 2437 MHz [6] (20.0 dBm)
- * 2442 MHz [7] (20.0 dBm)
- * 2447 MHz [8] (20.0 dBm)
- * 2452 MHz [9] (20.0 dBm)
- * 2457 MHz [10] (20.0 dBm)
- * 2462 MHz [11] (20.0 dBm)
- * 2467 MHz [12] (20.0 dBm)
- * 2472 MHz [13] (20.0 dBm)
- * 2484 MHz [14] (disabled)
- Band 2:
- Capabilities: 0x1062
- HT20/HT40
- Static SM Power Save
- RX HT20 SGI
- RX HT40 SGI
- No RX STBC
- Max AMSDU length: 3839 bytes
- DSSS/CCK HT40
- Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
- Minimum RX AMPDU time spacing: 16 usec (0x07)
- HT TX/RX MCS rate indexes supported: 0-7
- VHT Capabilities (0x00001020):
- Max MPDU length: 3895
- Supported Channel Width: neither 160 nor 80+80
- short GI (80 MHz)
- SU Beamformee
- VHT RX MCS set:
- 1 streams: MCS 0-9
- 2 streams: not supported
- 3 streams: not supported
- 4 streams: not supported
- 5 streams: not supported
- 6 streams: not supported
- 7 streams: not supported
- 8 streams: not supported
- VHT RX highest supported: 0 Mbps
- VHT TX MCS set:
- 1 streams: MCS 0-9
- 2 streams: not supported
- 3 streams: not supported
- 4 streams: not supported
- 5 streams: not supported
- 6 streams: not supported
- 7 streams: not supported
- 8 streams: not supported
- VHT TX highest supported: 0 Mbps
- Bitrates (non-HT):
- * 6.0 Mbps
- * 9.0 Mbps
- * 12.0 Mbps
- * 18.0 Mbps
- * 24.0 Mbps
- * 36.0 Mbps
- * 48.0 Mbps
- * 54.0 Mbps
- Frequencies:
- * 5170 MHz [34] (disabled)
- * 5180 MHz [36] (20.0 dBm)
- * 5190 MHz [38] (disabled)
- * 5200 MHz [40] (20.0 dBm)
- * 5210 MHz [42] (disabled)
- * 5220 MHz [44] (20.0 dBm)
- * 5230 MHz [46] (disabled)
- * 5240 MHz [48] (20.0 dBm)
- * 5260 MHz [52] (20.0 dBm) (no IR, radar detection)
- * 5280 MHz [56] (20.0 dBm) (no IR, radar detection)
- * 5300 MHz [60] (20.0 dBm) (no IR, radar detection)
- * 5320 MHz [64] (20.0 dBm) (no IR, radar detection)
- * 5500 MHz [100] (20.0 dBm) (no IR, radar detection)
- * 5520 MHz [104] (20.0 dBm) (no IR, radar detection)
- * 5540 MHz [108] (20.0 dBm) (no IR, radar detection)
- * 5560 MHz [112] (20.0 dBm) (no IR, radar detection)
- * 5580 MHz [116] (20.0 dBm) (no IR, radar detection)
- * 5600 MHz [120] (disabled)
- * 5620 MHz [124] (disabled)
- * 5640 MHz [128] (disabled)
- * 5660 MHz [132] (20.0 dBm) (no IR, radar detection)
- * 5680 MHz [136] (20.0 dBm) (no IR, radar detection)
- * 5700 MHz [140] (20.0 dBm) (no IR, radar detection)
- * 5720 MHz [144] (20.0 dBm) (no IR, radar detection)
- * 5745 MHz [149] (20.0 dBm)
- * 5765 MHz [153] (20.0 dBm)
- * 5785 MHz [157] (20.0 dBm)
- * 5805 MHz [161] (20.0 dBm)
- * 5825 MHz [165] (20.0 dBm)
- Supported commands:
- * new_interface
- * set_interface
- * new_key
- * start_ap
- * join_ibss
- * set_pmksa
- * del_pmksa
- * flush_pmksa
- * remain_on_channel
- * frame
- * set_wiphy_netns
- * set_channel
- * tdls_oper
- * start_sched_scan
- * start_p2p_device
- * connect
- * disconnect
- * crit_protocol_start
- * crit_protocol_stop
- * update_connect_params
- Supported TX frame types:
- * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- Supported RX frame types:
- * managed: 0x40 0xd0
- * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- * P2P-client: 0x40 0xd0
- * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- * P2P-device: 0x40 0xd0
- software interface modes (can always be added):
- valid interface combinations:
- * #{ managed } <= 1, #{ P2P-device } <= 1, #{ P2P-client, P2P-GO } <= 1,
- total <= 3, #channels <= 2
- * #{ managed } <= 1, #{ AP } <= 1, #{ P2P-client } <= 1, #{ P2P-device } <= 1,
- total <= 4, #channels <= 1
- Device supports scan flush.
- Device supports randomizing MAC-addr in sched scans.
- Supported extended features:
- * [ 4WAY_HANDSHAKE_STA_PSK ]: 4-way handshake with PSK in station mode
- * [ 4WAY_HANDSHAKE_STA_1X ]: 4-way handshake with 802.1X in station mode
- * [ DFS_OFFLOAD ]: DFS offload
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement