Found qca8k switch in ath79/ar1022_iodata_wn-ag300dgr.dts
Conf for cpu port0, Mode rgmii-id, With tx-internal-delay-ps of 2000
######################END################################
Found qca8k switch in ath79/qca9558_sitecom_wlr-8100.dts
Conf for cpu port0, Mode rgmii-id, With qca,mac6-exchange
Custom rule for phy0123 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port0 led 0 is set to mode rule
Custom rule for phy4 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port4 led 0 is set to mode rule
Custom rule for phy0123 led 1 applied using qca,led_rules
port0 led 1 is set to mode off
Custom rule for phy4 led 1 applied using qca,led_rules
port4 led 1 is set to mode off
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode off
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode off
port1 led 0 is set to mode rule
port1 led 1 is set to mode off
port1 led 2 is set to mode off
port2 led 0 is set to mode rule
port2 led 1 is set to mode off
port2 led 2 is set to mode off
port3 led 0 is set to mode rule
port3 led 1 is set to mode off
port3 led 2 is set to mode off
######################END################################
Found qca8k switch in ath79/ar9342_ubnt_wa_2port.dtsi
Conf for cpu port0, Mode rgmii-id
Custom rule for phy0123 led 2 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, collision-blink, link-10M, link-100M, link-1000M, power-on-reset, half-duplex, full-duplex
port0 led 2 is set to mode rule
Custom rule for phy4 led 2 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, collision-blink, link-10M, link-100M, link-1000M, power-on-reset, half-duplex, full-duplex
port4 led 2 is set to mode rule
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode rule
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode rule
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode rule
######################END################################
Found qca8k switch in ath79/qca9563_phicomm_k2t.dts
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
Custom rule for phy0123 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, power-on-reset
port0 led 1 is set to mode rule
Custom rule for phy4 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, power-on-reset
port4 led 1 is set to mode rule
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode off
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode off
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode off
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode off
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode off
######################END################################
Found qca8k switch in ath79/ar9344_qxwlan_e750g-v8-16m.dts
Conf for cpu port0, Mode rgmii-id
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode rule
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode rule
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode rule
######################END################################
Found qca8k switch in ath79/ar9344_qxwlan_e750g-v8-8m.dts
Conf for cpu port0, Mode rgmii-id
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode rule
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode rule
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode rule
######################END################################
Found qca8k switch in ath79/ar9344_ubnt_unifi-ap-pro.dts
Conf for cpu port0, Mode rgmii-id
Set qca,power-on-sel  in switch node
######################END################################
Found qca8k switch in ath79/ar9344_devolo_dlan_wifi.dtsi
Conf for cpu port0, Mode rgmii-txid
Absent config (regs set to 0x0) for pad5. Not attached port5?
Absent config (regs set to 0x0) for pad6. Not attached port6?
######################END################################
Found qca8k switch in ath79/qca9563_tplink_archer-x6-v2.dtsi
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
######################END################################
Found qca8k switch in ath79/qca9563_tplink_tl-wpa8630.dtsi
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
######################END################################
Found qca8k switch in ath79/qca9557_iodata_wn-ac-dgr.dtsi
Conf for cpu port0, Mode rgmii-id, With qca,mac6-exchange
######################END################################
Found qca8k switch in ath79/ar9344_pcs_cr5000.dts
Conf for cpu port0, Mode rgmii-id
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode rule
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode rule
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode rule
######################END################################
Found qca8k switch in ath79/qca9563_nec_wg1200cr.dts
Conf for cpu port0, Mode sgmii
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode rule
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode rule
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode rule
######################END################################
Found qca8k switch in ath79/ar9342_iodata_etg3-r.dts
Conf for cpu port0, Mode rgmii-id
Custom rule for phy0123 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, collision-blink, link-10M, link-100M, link-1000M, power-on-reset, half-duplex, full-duplex
port0 led 0 is set to mode rule
Custom rule for phy4 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, collision-blink, link-10M, link-100M, link-1000M, power-on-reset, half-duplex, full-duplex
port4 led 0 is set to mode rule
Custom rule for phy0123 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, collision-blink, link-10M, link-100M, link-1000M, power-on-reset, half-duplex, full-duplex
port0 led 1 is set to mode rule
Custom rule for phy4 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, collision-blink, link-10M, link-100M, link-1000M, power-on-reset, half-duplex, full-duplex
port4 led 1 is set to mode rule
Custom rule for phy0123 led 2 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, collision-blink, link-10M, link-100M, link-1000M, power-on-reset, half-duplex, full-duplex
port0 led 2 is set to mode rule
Custom rule for phy4 led 2 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, collision-blink, link-10M, link-100M, link-1000M, power-on-reset, half-duplex, full-duplex
port4 led 2 is set to mode rule
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode rule
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode rule
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode rule
######################END################################
Found qca8k switch in ath79/ar9344_tplink_tl-wdr4300.dtsi
Conf for cpu port0, Mode rgmii-id
Set qca,power-on-sel  in switch node
Custom rule for phy0123 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M
port0 led 0 is set to mode rule
Custom rule for phy4 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M
port4 led 0 is set to mode rule
Custom rule for phy0123 led 1 applied using qca,led_rules
port0 led 1 is set to mode off
Custom rule for phy4 led 1 applied using qca,led_rules
port4 led 1 is set to mode off
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode off
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode off
port1 led 0 is set to mode rule
port1 led 1 is set to mode off
port1 led 2 is set to mode off
port2 led 0 is set to mode rule
port2 led 1 is set to mode off
port2 led 2 is set to mode off
port3 led 0 is set to mode rule
port3 led 1 is set to mode off
port3 led 2 is set to mode off
######################END################################
Found qca8k switch in ath79/ar1022_sitecom_wlr-7100.dts
Conf for cpu port0, Mode rgmii-id, With tx-internal-delay-ps of 2000, With qca,mac6-exchange
Conf for cpu port6, Mode rgmii-rxid
Set qca,power-on-sel  in switch node
######################END################################
Found qca8k switch in ath79/qca9558_tplink_tl-wdr4900-v2.dts
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
Conf for cpu port6, Mode rgmii-id
Custom rule for phy0123 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M
port0 led 0 is set to mode rule
Custom rule for phy4 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M
port4 led 0 is set to mode rule
Custom rule for phy0123 led 1 applied using qca,led_rules
port0 led 1 is set to mode off
Custom rule for phy4 led 1 applied using qca,led_rules
port4 led 1 is set to mode off
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode off
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode off
port1 led 0 is set to mode rule
port1 led 1 is set to mode off
port1 led 2 is set to mode off
port2 led 0 is set to mode rule
port2 led 1 is set to mode off
port2 led 2 is set to mode off
port3 led 0 is set to mode rule
port3 led 1 is set to mode off
port3 led 2 is set to mode off
######################END################################
Found qca8k switch in ath79/qca9563_tplink_archer-c7-v4.dts
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge, With qca,mac6-exchange
######################END################################
Found qca8k switch in ath79/qca9563_xiaomi_aiot-ac2350.dts
Conf for cpu port0, Mode sgmii
Conf for cpu port5, Mode rgmii-rxid
Absent config (regs set to 0x0) for pad6. Not attached port6?
!!MISSING TO CONVERT REMAINING BIT 0x60000000 FOR REG 0x10

Custom rule for phy0123 led 0 applied using qca,led_rules, blink-4hz, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port0 led 0 is set to mode rule
Custom rule for phy4 led 0 applied using qca,led_rules, blink-4hz, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port4 led 0 is set to mode rule
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode rule
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode rule
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode rule
Sgmii mode set to PHY If set to PHY you can ignore this settings as qca8k should automatically set this
######################END################################
Found qca8k switch in ath79/qca9563_netgear_wndr.dtsi
Conf for cpu port0, Mode sgmii
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
Custom rule for phy0123 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, power-on-reset
port0 led 1 is set to mode rule
Custom rule for phy4 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, power-on-reset
port4 led 1 is set to mode rule
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode off
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode off
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode off
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode off
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode off
######################END################################
Found qca8k switch in ath79/qca9558_librerouter_librerouter-v1.dts
Conf for cpu port0, Mode rgmii-id, With qca,mac6-exchange
Conf for cpu port6, Mode sgmii
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
Custom rule for phy0123 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port0 led 0 is set to mode rule
Custom rule for phy4 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port4 led 0 is set to mode rule
Custom rule for phy0123 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port0 led 1 is set to mode rule
Custom rule for phy4 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port4 led 1 is set to mode rule
Custom rule for phy0123 led 2 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port0 led 2 is set to mode rule
Custom rule for phy4 led 2 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port4 led 2 is set to mode rule
port1 led 0 is set to mode off
port1 led 1 is set to mode off
port1 led 2 is set to mode off
port2 led 0 is set to mode off
port2 led 1 is set to mode off
port2 led 2 is set to mode off
port3 led 0 is set to mode off
port3 led 1 is set to mode off
port3 led 2 is set to mode off
######################END################################
Found qca8k switch in ath79/qca9563_compex_wpj563.dts
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
######################END################################
Found qca8k switch in ath79/qca9563_tplink_tl-wr1043n.dtsi
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
######################END################################
Found qca8k switch in ath79/qca9563_comfast_cf-e375ac.dts
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
######################END################################
Found qca8k switch in ath79/ar9344_dlink_dir-8x5.dtsi
!!MISSING TO CONVERT REMAINING BIT 0x40000000 FOR REG 0x10
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
Conf for cpu port0, Mode rgmii-id
Conf for cpu port6, Mode rgmii-rxid
######################END################################
Found qca8k switch in ath79/qca9563_tplink_archer-x7-v5.dtsi
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge, With qca,mac6-exchange
Absent config (regs set to 0x0) for pad5. Not attached port5?
Absent config (regs set to 0x0) for pad6. Not attached port6?

######################END################################
Found qca8k switch in ath79/qca9558_tplink_tl-wr1043nd.dtsi
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
Conf for cpu port6, Mode rgmii-id
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode rule
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode rule
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode rule
######################END################################
Found qca8k switch in ath79/qca9563_rosinson_wr818.dts
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
######################END################################
Found qca8k switch in ath79/qca9558_dlink_dap-2695-a1.dts
Conf for cpu port0, Mode rgmii-id
Conf for cpu port6, Mode sgmii, With qca,sgmii-rxclk-falling-edge
######################END################################
Found qca8k switch in ath79/qca9563_elecom_wrc-ghbk2-i.dtsi
Conf for cpu port0, Mode sgmii
Custom rule for phy0123 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port0 led 0 is set to mode rule
Custom rule for phy4 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port4 led 0 is set to mode rule
Custom rule for phy0123 led 1 applied using qca,led_rules
port0 led 1 is set to mode off
Custom rule for phy4 led 1 applied using qca,led_rules
port4 led 1 is set to mode off
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode off
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode off
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode rule
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode rule
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode rule
######################END################################
Found qca8k switch in ath79/qca9558_tplink_archer-d7.dtsi
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
Conf for cpu port6, Mode rgmii-id
Custom rule for phy0123 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M
port0 led 0 is set to mode rule
Custom rule for phy4 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M
port4 led 0 is set to mode rule
Custom rule for phy0123 led 1 applied using qca,led_rules
port0 led 1 is set to mode off
Custom rule for phy4 led 1 applied using qca,led_rules
port4 led 1 is set to mode off
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode off
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode off
port1 led 0 is set to mode rule
port1 led 1 is set to mode off
port1 led 2 is set to mode off
port2 led 0 is set to mode rule
port2 led 1 is set to mode off
port2 led 2 is set to mode off
port3 led 0 is set to mode rule
port3 led 1 is set to mode off
port3 led 2 is set to mode off
######################END################################
Found qca8k switch in ath79/qca9558_dlink_dap-3662-a1.dts
Conf for cpu port0, Mode rgmii-id
Conf for cpu port6, Mode sgmii, With qca,sgmii-rxclk-falling-edge
######################END################################
Found qca8k switch in ath79/qca9558_engenius_epg5000.dts
Conf for cpu port0, Mode rgmii-id, With qca,mac6-exchange
######################END################################
Found qca8k switch in ath79/qca9563_tplink_archer-c2-v3.dts
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
######################END################################
Found qca8k switch in ath79/ar7242_ubnt_edgeswitch-5xp.dts
Conf for cpu port0, Mode rgmii-rxid, With rx-internal-delay-ps of 1000
Conf for cpu port6, Mode rgmii-rxid, With rx-internal-delay-ps of 1000
Custom rule for phy0123 led 0 applied using qca,led_rules
port0 led 0 is set to mode blink
Custom rule for phy4 led 0 applied using qca,led_rules
port4 led 0 is set to mode blink
Custom rule for phy0123 led 1 applied using qca,led_rules
port0 led 1 is set to mode blink
Custom rule for phy4 led 1 applied using qca,led_rules
port4 led 1 is set to mode blink
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode blink
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode blink
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode rule
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode rule
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode rule
######################END################################
Found qca8k switch in ath79/qca9563_glinet_gl-ar750s.dtsi
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
######################END################################
Found qca8k switch in ath79/qca9558_trendnet_tew-823dru.dts
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
Conf for cpu port6, Mode rgmii-id
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
######################END################################
Found qca8k switch in ath79/qca9563_dlink_dir-842-c.dtsi
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
Custom rule for phy0123 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, power-on-reset
port0 led 1 is set to mode rule
Custom rule for phy4 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, power-on-reset
port4 led 1 is set to mode rule
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode off
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode off
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode off
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode off
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode off
######################END################################
Found qca8k switch in ath79/ar9342_ubnt_aircube-ac.dts
Conf for cpu port0, Mode rgmii-id
######################END################################
Found qca8k switch in ath79/qca9557_buffalo_bhr-4grv2.dts
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge, With qca,mac6-exchange
Conf for cpu port6, Mode rgmii-id
######################END################################
Found qca8k switch in ath79/qca955x_zyxel_nbg6x16.dtsi
Conf for cpu port0, Mode rgmii-id, With qca,mac6-exchange
Conf for cpu port6, Mode sgmii, With qca,sgmii-rxclk-falling-edge
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
Custom rule for phy0123 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, collision-blink, link-10M, link-100M, link-1000M, power-on-reset, half-duplex, full-duplex
port0 led 0 is set to mode rule
Custom rule for phy4 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, collision-blink, link-10M, link-100M, link-1000M, power-on-reset, half-duplex, full-duplex
port4 led 0 is set to mode rule
Custom rule for phy0123 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, collision-blink, link-10M, link-100M, link-1000M, power-on-reset, half-duplex, full-duplex
port0 led 1 is set to mode rule
Custom rule for phy4 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, collision-blink, link-10M, link-100M, link-1000M, power-on-reset, half-duplex, full-duplex
port4 led 1 is set to mode rule
Custom rule for phy0123 led 2 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, collision-blink, link-10M, link-100M, link-1000M, power-on-reset, half-duplex, full-duplex
port0 led 2 is set to mode rule
Custom rule for phy4 led 2 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, collision-blink, link-10M, link-100M, link-1000M, power-on-reset, half-duplex, full-duplex
port4 led 2 is set to mode rule
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode rule
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode rule
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode rule
######################END################################
Found qca8k switch in ath79/qca9558_qxwlan_e558.dtsi
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
Conf for cpu port6, Mode rgmii-id
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode rule
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode rule
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode rule
######################END################################
Found qca8k switch in ath79/ar9344_compex_wpj344-16m.dts
Conf for cpu port0, Mode rgmii-id
Set qca,power-on-sel  in switch node
Custom rule for phy0123 led 0 applied using qca,led_rules
port0 led 0 is set to mode off
Custom rule for phy4 led 0 applied using qca,led_rules
port4 led 0 is set to mode off
Custom rule for phy0123 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M
port0 led 1 is set to mode rule
Custom rule for phy4 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M
port4 led 1 is set to mode rule
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode off
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode off
port1 led 0 is set to mode off
port1 led 1 is set to mode rule
port1 led 2 is set to mode off
port2 led 0 is set to mode off
port2 led 1 is set to mode rule
port2 led 2 is set to mode off
port3 led 0 is set to mode off
port3 led 1 is set to mode rule
port3 led 2 is set to mode off
######################END################################
Found qca8k switch in ath79/qca9558_compex_wpj558-16m.dts
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
Conf for cpu port6, Mode rgmii-id
Custom rule for phy0123 led 1 applied using qca,led_rules
port0 led 1 is set to mode off
Custom rule for phy4 led 1 applied using qca,led_rules
port4 led 1 is set to mode off
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode off
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode off
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode rule
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode rule
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode rule
######################END################################
Found qca8k switch in ath79/qca9563_tplink_eap245-v3.dts
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
Sgmii mode set to PHY If set to PHY you can ignore this settings as qca8k should automatically set this
######################END################################
Found qca8k switch in ath79/qca9558_domywifi_dw33d.dts
Conf for cpu port0, Mode rgmii-id, With qca,mac6-exchange
Conf for cpu port6, Mode sgmii, With qca,sgmii-rxclk-falling-edge
######################END################################
Found qca8k switch in ath79/qca9563_ubnt_unifiac-pro.dtsi
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
######################END################################
Found qca8k switch in ath79/qca9563_yuncore_xd4200.dtsi
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
Custom rule for phy0123 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port0 led 0 is set to mode rule
Custom rule for phy4 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port4 led 0 is set to mode rule
Custom rule for phy0123 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port0 led 1 is set to mode rule
Custom rule for phy4 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port4 led 1 is set to mode rule
Custom rule for phy0123 led 2 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port0 led 2 is set to mode rule
Custom rule for phy4 led 2 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M, power-on-reset
port4 led 2 is set to mode rule
port1 led 0 is set to mode rule
port1 led 1 is set to mode off
port1 led 2 is set to mode off
port2 led 0 is set to mode rule
port2 led 1 is set to mode off
port2 led 2 is set to mode off
port3 led 0 is set to mode off
port3 led 1 is set to mode off
port3 led 2 is set to mode off
######################END################################
Found qca8k switch in ath79/qca9558_comfast_cf-wr650ac.dtsi
Conf for cpu port0, Mode rgmii-id, With qca,mac6-exchange
Conf for cpu port6, Mode sgmii, With qca,sgmii-rxclk-falling-edge
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
######################END################################
Found qca8k switch in ath79/ar9344_atheros_db120.dts
Conf for cpu port0, Mode rgmii-id
!!MISSING TO CONVERT REMAINING BIT 0x40000000 FOR REG 0x10
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
######################END################################
Found qca8k switch in ath79/qca9563_nec_wg800hp.dts
Conf for cpu port0, Mode sgmii
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode rule
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode rule
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode rule
######################END################################
Found qca8k switch in ath79/qca9550_airtight_c-75.dts
Conf for cpu port0, Mode rgmii-id
Conf for cpu port6, Mode sgmii, With qca,sgmii-rxclk-falling-edge
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode rule
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode rule
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode rule
######################END################################
Found qca8k switch in ath79/ar9344_wd_mynet-n750.dts
Conf for cpu port0, Mode rgmii-id
Set qca,power-on-sel  in switch node
Custom rule for phy0123 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M
port0 led 0 is set to mode rule
Custom rule for phy4 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M
port4 led 0 is set to mode rule
Custom rule for phy0123 led 1 applied using qca,led_rules
port0 led 1 is set to mode off
Custom rule for phy4 led 1 applied using qca,led_rules
port4 led 1 is set to mode off
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode off
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode off
port1 led 0 is set to mode rule
port1 led 1 is set to mode off
port1 led 2 is set to mode off
port2 led 0 is set to mode rule
port2 led 1 is set to mode off
port2 led 2 is set to mode off
port3 led 0 is set to mode rule
port3 led 1 is set to mode off
port3 led 2 is set to mode off
######################END################################
Found qca8k switch in ath79/qca9558_tplink_archer-c.dtsi
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
Conf for cpu port6, Mode rgmii-id
Custom rule for phy0123 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M
port0 led 0 is set to mode rule
Custom rule for phy4 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M
port4 led 0 is set to mode rule
Custom rule for phy0123 led 1 applied using qca,led_rules
port0 led 1 is set to mode off
Custom rule for phy4 led 1 applied using qca,led_rules
port4 led 1 is set to mode off
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode off
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode off
port1 led 0 is set to mode rule
port1 led 1 is set to mode off
port1 led 2 is set to mode off
port2 led 0 is set to mode rule
port2 led 1 is set to mode off
port2 led 2 is set to mode off
port3 led 0 is set to mode rule
port3 led 1 is set to mode off
port3 led 2 is set to mode off
######################END################################
Found qca8k switch in ath79/qca9563_dlink_dir-859-a1.dts
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
Custom rule for phy0123 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, power-on-reset
port0 led 1 is set to mode rule
Custom rule for phy4 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, power-on-reset
port4 led 1 is set to mode rule
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode off
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode off
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode off
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode off
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode off
######################END################################
Found qca8k switch in ath79/ar9344_netgear_wndr.dtsi
Conf for cpu port0, Mode rgmii-id
Conf for cpu port6, Mode rgmii-rxid
!!MISSING TO CONVERT REMAINING BIT 0x40000000 FOR REG 0x10
Set qca,power-on-sel  in switch node, Set qca,led-open-drain  in switch node
Custom rule for phy0123 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, power-on-reset
port0 led 1 is set to mode rule
Custom rule for phy4 led 1 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, power-on-reset
port4 led 1 is set to mode rule
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode off
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode off
port1 led 0 is set to mode rule
port1 led 1 is set to mode rule
port1 led 2 is set to mode off
port2 led 0 is set to mode rule
port2 led 1 is set to mode rule
port2 led 2 is set to mode off
port3 led 0 is set to mode rule
port3 led 1 is set to mode rule
port3 led 2 is set to mode off
######################END################################
Found qca8k switch in ath79/qca9563_qxwlan_e1700ac.dtsi
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
######################END################################
Found qca8k switch in ath79/qca9558_belkin_f9x-v2.dtsi
Conf for cpu port0, Mode sgmii, With qca,sgmii-rxclk-falling-edge
Conf for cpu port6, Mode rgmii-id
Custom rule for phy0123 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M
port0 led 0 is set to mode rule
Custom rule for phy4 led 0 applied using qca,led_rules, blink-auto, tx-blink, rx-blink, link-10M, link-100M, link-1000M
port4 led 0 is set to mode rule
Custom rule for phy0123 led 1 applied using qca,led_rules
port0 led 1 is set to mode off
Custom rule for phy4 led 1 applied using qca,led_rules
port4 led 1 is set to mode off
Custom rule for phy0123 led 2 applied using qca,led_rules
port0 led 2 is set to mode off
Custom rule for phy4 led 2 applied using qca,led_rules
port4 led 2 is set to mode off
port1 led 0 is set to mode rule
port1 led 1 is set to mode off
port1 led 2 is set to mode off
port2 led 0 is set to mode rule
port2 led 1 is set to mode off
port2 led 2 is set to mode off
port3 led 0 is set to mode rule
port3 led 1 is set to mode off
port3 led 2 is set to mode off
######################END################################