21:09:48
// probe at 205.000,150.000 is z=-0.726250
21:09:49
// probe at 205.000,150.000 is z=-0.727656
21:09:50
// probe at 205.000,150.000 is z=-0.727813
21:09:53
// probe at 260.000,150.000 is z=-0.732031
21:09:54
// probe at 260.000,150.000 is z=-0.734375
21:09:55
// probe at 260.000,150.000 is z=-0.735625
21:09:58
// probe at 260.000,205.000 is z=-0.727031
21:09:59
// probe at 260.000,205.000 is z=-0.728594
21:10:00
// probe at 260.000,205.000 is z=-0.730000
21:10:03
// probe at 205.000,205.000 is z=-0.714375
21:10:04
// probe at 205.000,205.000 is z=-0.714219
21:10:06
// probe at 205.000,205.000 is z=-0.715313
21:10:09
// probe at 150.000,205.000 is z=-0.674375
21:10:10
// probe at 150.000,205.000 is z=-0.675625
21:10:11
// probe at 150.000,205.000 is z=-0.677031
21:10:14
// probe at 95.000,205.000 is z=-0.690625
21:10:15
// probe at 95.000,205.000 is z=-0.691719
21:10:16
// probe at 95.000,205.000 is z=-0.692500
21:10:19
// probe at 40.000,205.000 is z=-0.701875
21:10:20
// probe at 40.000,205.000 is z=-0.702813
21:10:21
// probe at 40.000,205.000 is z=-0.702969
21:10:24
// probe at 40.000,260.000 is z=-0.638125
21:10:25
// probe at 40.000,260.000 is z=-0.640156
21:10:27
// probe at 40.000,260.000 is z=-0.640625
21:10:29
// probe at 95.000,260.000 is z=-0.640313
21:10:31
// probe at 95.000,260.000 is z=-0.640469
21:10:32
// probe at 95.000,260.000 is z=-0.642188
21:10:35
// probe at 150.000,260.000 is z=-0.643125
21:10:36
// probe at 150.000,260.000 is z=-0.645156
21:10:37
// probe at 150.000,260.000 is z=-0.646563
21:10:40
// probe at 205.000,260.000 is z=-0.662969
21:10:41
// probe at 205.000,260.000 is z=-0.664063
21:10:42
// probe at 205.000,260.000 is z=-0.664688
21:10:45
// probe at 260.000,260.000 is z=-0.676250
21:10:46
// probe at 260.000,260.000 is z=-0.678125
21:10:47
// probe at 260.000,260.000 is z=-0.679219
21:10:48
// Mesh Bed Leveling Complete
21:10:48
// Bed Mesh state has been saved to profile [default]
// for the current session. The SAVE_CONFIG command will
// update the printer config file and restart the printer.
21:11:57
// Moving filament tip 0.0mms
21:11:57
// KAMP purge is not using firmware retraction, it is recommended to configure it.